Liquid-liquid extraction of tungsten(VI) with mesityl oxide application to an alloy steel

A new and simple method has been developed for the rapid extraction of tungsten(VI) with mesityl oxide. Quantitative extraction occurs from solutions 1M in hydrochloric acid and 12M in lithium chloride (as the salting-out agent) with 75% mesityl oxide in isobutyl methyl ketone. Tungsten is finally determined photometrically as the thiocyanate complex in the aqueous phase. Tungsten-(VI) can be extracted and determined satisfactorily in the presence of several elements. The method is shown to be applicable to an alloy steel.     

Extraction of zinc with tri(iso-octyl)amine in methyl isobutyl ketone and colorimetric determination with zincon in the organic phase

A study was made of the extraction of zinc from hydrochloric acid solutions with solutions of methyldioctylamine and tri(iso-octyl)amine in methyl isobutyl ketone. Quantitative extraction was accomplished from 2 N hydrochloric acid with 5% (w/v) tri(iso-octyl)amine-methyl isobutyl ketone. A procedure was developed for the colorimetric determination of zinc in the organic phase after extraction using 2-carboxy-2'-hydroxy-5'-sulfoformazylbenzene (Zincon).     

Solvent extraction of chromium(VI) from base metal ions with diphenyl-2-pyridylmethane as a liquid anion exchanger

The extraction of chromium(VI) from aqueous hydrochloric, nitric and sulfuric acid solutions by diphenyl-2-pyridylmethane(DPPM) dissolved in chloroform has been studied. Chromium(VI) is quantitatively extracted from hydrochloric acid solutions in the range 0.1–1M. With increasing acid concentration, the extraction of chromium diminishes and in concentrated acid solutions practically all the chromium remains in the aqueous phase. The quantitative back-extraction of chromium from the organic phase is possible with HCl or HNO₃ at concentrations higher than 5M through the use of reducing agents. The composition of the extracted chromium(VI) species was studied in solution. The complexes (DPPMH)⁺HCrO ₄ ⁻ and (DPPMH)₂Cr₂O ₇ ⁻ are extracted for tracer and macro amounts of chromium(VI) respectively. The data have been utilized for the separation of chromium(VI) from base metal ions.     

Masking of iron with fluoride in the extractive atomic-absorption spectrometric determination of chromium in steel

Chromium in steel is determined by oxidation to dichromate, extraction into methyl isobutyl ketone from 1-3 M hydrochloric acid, and atomic-absorption measurements on the extract. The interference of iron in the atomic absorption is eliminated by using fluoride to keep the iron(III) in the aqueous phase in the extraction step.     

Studies on the extraction and determination of metal salts with isobutyl methyl ketone-XIII Extraction of thorium and uranium

The work deals with the extraction of thorium or uranium from hydrochloric, perchloric, sulphuric or nitric acid solutions of various concentrations, or from mixed acid solutions, by means of isobutyl methyl ketone. When the extraction is made from 5-8M hydrochloric acid that is 10M in lithium chloride or from 7-8M hydrochloric acid that is 1M in magnesium chloride, uranium is extracted quantitatively (>99%), whereas thorium is hardly extracted at all.     

Flame atomic absorption spectrometry of silver and gold in copper intermediates

The effect of hydrochloric acid and salts from the sample on the solubility of methyl isobutyl ketone (MIBK) in aqueous phase and the effect of hydrochloric acid concentration on the MIBK extraction of iron(III) and gold(III) were studied. As a result, an improved method by flame atomic absorption sepctrometry for determination of silver and gold in copper intermediates was developed, employing a more efficient removal of iron and special standards depending upon the concentration of salts introduced by different samples.     

Studies on the extraction and determination of metal salts with isobutyl methyl ketone-XIV Extraction of gold

The isobutyl methyl ketone extraction of gold(III) from hydrochloric acid or various mixtures of hydrochloric and other mineral acids was studied as a function of the gold concentration and the acid concentration. Gold (initial concentration up to 5 x 10(-3)M) was quantitatively extracted (99%) from 3-5M hydrochloric acid. Addition of nitric acid in 1-5M concentration and sulphuric or perchloric acid in 1-3N concentration to the 1-5M hydrochloric acid solutions used had no effect.     

Separation of Cr(III) and Cr(VI) using complexation of Cr(III) with 8-hydroxyquinoline and determination of both species in waters by ETA-AAS

Summary A method for the determination of chromium(III) and (VI) species has been studied and applied to mineral water samples. The chromium(III) was chelated with 0.1 mol/l 8-hydroxyquinoline in methyl alcohol, extracted in isobutyl methyl ketone and determined by ETA-AAS. The effects of the pH, extraction and heating time and amounts of the reagents required for the extraction were studied. A method for the determination of total chromium was optimized too, and the chromium(VI) can be calculated. The precision, sensibility, accuracy, graphite furnace program and interferences for both methods were also investigated.     

Effect of acidity on the extraction and kinetic stability of the copper(II)/APCD/IBMK system in strongly acidic media

The extraction of copper(II) from strongly acidic solution (0.01-8M hydrochloric acid) with ammonium 1-pyrrolidinecarbodithioate in isobutyl methyl ketone has been investigated. The shaking time needed for quantitative extraction decreases as the acidity is increased. The effect of the mutual solubility of the organic solvent and the aqueous phase is significant when the acidity of the aqueous phase is increased. The acidity of the aqueous phase mainly affects the kinetic stability of the chelate during the shaking period, rather than the decomposition of the chelating agent. The kinetic stability of the chelate apparently depends on the mole ratio of reagent to copper, the half-lives for the chelate extracted from 4M hydrochloric acid being 29.0, 40.0 and 85.0 min for reagent: metal mole ratios of 10, 100 and 1000, respectively.     

Removal of iron interferences by solvent extraction for geochemical analysis by atomic-absorption spectrophotometry

Iron is a common interferent in the determination of many elements in geochemical samples. Two approaches for its removal have been taken. The first involves removal of iron by extraction with methyl isobutyl ketone (MIBK) from hydrochloric acid medium, leaving the analytes in the aqueous phase. The second consists of reduction of iron(III) to iron(II) by ascorbic acid to minimize its extraction into MIBK, so that the analytes may be isolated by extraction. Elements of interest can then be determined using the aqueous solution or the organic extract, as appropriate. Operating factors such as the concentration of hydrochloric acid, amounts of iron present, number of extractions, the presence or absence of a salting-out agent, and the optimum ratio of ascorbic acid to iron have been determined. These factors have general applications in geochemical analysis by atomic-absorption spectrophotometry.     

Determination of gallium in an iron-aluminium matrix by solvent extraction and flame emission spectroscopy

Solvent extraction of gallium(III) into methyl isobutyl ketone from hydrochloric acid solutions containing titanium (III) sulphate provides a rapid method for separation of gallium from an iron/aluminium matrix and may be employed to eliminate the interference of these elements in the flame emission spectrometric determination of gallium.     

The determination of chromium in biological materials by atomic absorption spectroscopy

Biological samples were mineralized with a mixture of nitric, sulfuric, and perchloric acids. The chromium was oxidized to chromium(VI) followed by extraction into methyl isobutyl ketone in the cold. The ketone extract was aspirated into a fuel-rich hydrogen-air flame, and the absorption recorded using the 357.9 nm line of chromium. The limit of detection for chromium was found to be 10 p.p.b. Tissue chromium levels of normal albino rats were determined. Increased chromium values were observed for animals maintained on a high chromium diet compared to those fed a deficient diet.     

Comparative study of IBMK and DIBK as extraction solvents in strongly acidic media: extraction behaviour and kinetic stability of Cu(PCD)(2) in these solvents

The use of di-isobutyl ketone (DIBK) and isobutyl methyl ketone (IBMK) as the solvent for extraction of copper(II) from strongly acidic media (0.01-8M hydrochloric acid) with ammonium l-pyrrolidinecarbodithioate has been studied. In contrast to IBMK, the volume of the DIBK extract remains the same, irrespective of the acidity of the aqueous phase. A certain amount of free acid is transferred into both solvents, and affects the kinetic stability of the chelate extracted; the free acid can be completely removed by washing the extract with water, and partly by filtering it through a dry filter paper. However, the chelate extracted into DIBK exhibits excellent stability without such treatment, since the amount of free acid in DIBK is much smaller than that in IBMK. When DIBK is used, the copper chelate can be quantitatively extracted as long as the extraction is done from acidic media.     

Solvent extraction of metals with hydroxamic acids

Solvent extraction with hydroxamic acids has been investigated. with comparison of aliphatic and aromatic reagents for the extraction of iron, copper, cobalt and nickel. Caprylohydroxamic acid has been evaluated for use in extraction systems for titanium, vanadium, chromium, molybdenum and uranium, both in terms of acidity of aqueous phase and oxidation state of the metal. It has been established that caprylohydroxamic acid in 1-hexanol is a suitable extractant for the removal of titanium(IV), vanadium(V), chromium(VI), molybdenum(VI) and uranium(VI) from 6M hydrochloric acid.     

Cr(III)/Cr(VI) speciation in aerosol particles by extractive separation and thermal ionization isotope dilution mass spectrometry

 An isotope dilution mass spectrometric (IDMS) method, using the formation of positive thermal ions, was developed for Cr(III) and Cr(VI) speciation in aerosol particles. Cr(III) and Cr(VI) spike species, enriched in ⁵³Cr, were applied for the isotope dilution step. After leaching of filter collected aerosol samples by an alkaline solution at pH 13, species separation was carried out by extraction with a liquid anion exchanger in methyl isobutyl ketone. Cr(VI) in the organic phase was re-extracted into an ammoniacal solution and chromium was then isolated from both fractions of species by electrodeposition. Detection limits of 30 pg/m³ for Cr(III) and of 8 pg/m³ for Cr(VI) were achieved in atmospheric aerosols for volumes of air samples of about 120 m³. These low detection limits allowed the determination of chromium species in continental aerosol particles in dependence on different seasons. The Cr(III) /Cr(VI) ratio was always found to be about 0.3 whereas dust from soil erosion, which is probably the primary source of chromium in the atmosphere, showed higher ratios. This indicates that chromium is oxidized in the atmosphere. The accuracy of the method was demonstrated in two interlaboratory comparisons of Cr(VI) determinations in welding dust samples. The IDMS method also contributed to the certification of a corresponding standard reference material organized by the Standard Reference Bureau of the European Union. Chromium speciation, including the determination of elemental chromium Cr(0), was carried out in aerosols of different welding processes for stainless steel. These analyses showed distinct differences in the distribution of chromium species in the welding process and can be used as an exact calibration method for routine methods in this important field of monitoring corresponding working places. Received: 19 August 1996/Revised: 24 September 1996/Accepted: 28 September 1996     

Hexavalent chromium recovery by liquid-liquid extraction with tributylphosphate from acidic chloride media.

A method is introduced for recuperation of chromium(VI) in water samples by liquid-liquid extraction with tributylphosphate PO(C4H9O)3 (TBP) from acidic chloride media. The optimum conditions for quantitative extraction of Cr(VI) were evaluated by varying the experimental parameters, such as the shaking period, the pH of the aqueous phase, the hydrochloric acid concentration, the hydrogen and chloride ion concentrations, the extractant concentration and the ratio of aqueous-to-organic phase. The probable extracted species of hexavalent chromium in organic phase, deduced from log-log plots, were H2CrO4 in acid media in absence of chloride and HCrO3Cl in acidic chloride media. Chromium(VI) was found to be extracted with tributylphosphate from acidic chloride media according to the following reaction: HCrO4-(aq), + 2H+(aq) + Cl-(aq) + 2TBP(org) <==> [HCrO3Cl, 2TBP](org) + H2O(aq). Since the tributylphosphate (TBP) exhibited a high selectivity for chromium(VI), this method can be applicable to the extraction and the determination of chromium in both oxidation states [Cr(VI) and Cr(III)] in water samples.     

The extraction of lead iodide by methyl iso-propyl ketone

A method is proposed for the isolation of lead by solvent extraction. When solutions of lead ions are treated with excess potassium iodide and hydrochloric acid (5 %), lead iodide is extracted quantitatively by methyl iso-propyl ketone. Employing a preliminary extraction with methyl iso-propyl ketone after conditioning the aqueous solution with ammonium thiocyanate and hydrochloric acid, practically all interferences are eliminated (except Cd and Ru).     

Atomic absorption determination of indium after extraction with di-(2-ethylhexyl)phosphoric acid

The equilibrium data show that indium can be quickly extracted from acidic aqueous solutions by di-(2-ethylhexyl)phosphoric acid in methyl isobutyl ketone. In this polar solvent the species ML₃·HL is extracted. The overall extraction constant is higher than that for other tervalent metals. The extraction process can be combined with AAS determination of the indium. The method is fast because stripping is not necessary, and the organic phase can be analysed directly by AAS. Use of a 51 v/v aqueous: organic phase ratio increases the sensitivity. In the pH-range used the method has good selectivity.     

Solvent extraction behaviour of thiocyanic acid

The solvent extraction behaviour of thiocyanic acid with isobutyl methyl ketone and xylene as solvents is described. In the ketone system the thiocyanic acid is solvated in the organic phase to give a complex with a proposed composition of HSCN. 2IBMK. Deviations from ideal behaviour, which can be attributed to variations in the activity coefficient of the acid in the aqueous phase, are shown.