Determination of calcium,magnesium, and phosphate in the presence of iron and each other

Excess EDTA and MgSO₄ solution is added to a mildly acidic solution of the sample containing calcium, magnesium, iron, and phosphate ions. Addition of NH₄OH to this solution results in the precipitation of MgNH₄PO₄·6H₂O and various iron compounds. Calcium ions and a portion of the magnesium ions stay in the solution as the respective EDTA chelates. The mixture is adjusted to a known volume and filtered. The EDTA content of the filtrate with the exception of the EDTA tied up as calcium-EDTA chelate, is titrated with standard CaCl₂ solution at pH 12.5–13.0 in the presence of hydroxy naphthol blue indicator. The calcium content of the sample can be calculated from the result of this titration.     

Influence of chemical dealumination on the properties of USY zeolite

Three series of dealuminated Y zeolites have been prepared by chemical extraction ofhydrothermally dealuminated Y zeolite(USY)with H_2Na_2EDTA,HCl and H_4EDTA.The unitcell constant,mesopore distribution,acidity and extraframework aluminum(EFAL)of thezeolites were studied with XRD,chemical analyses,adsorption,IR and NH_3-TPD techniques.It was shown that H_2Na_2EDTA only removed EFAL species deposited in the pores of USY,by contrast,HCl and H_4EDTA extract both extraframework and framework aluminum,andmake the zeolite framework further dealuminated.Adsorption tests gave evidence that a second-ary pore system exists in these dealuminated zeolites.H_2Na_2EDTA extraction increased bothmicropore and mesopore volumes,but after HCl and H_4EDTA treatments,new mesopores formedand the micropore volume was decreased.The pyridine-IR and NH_3-TPD measurements demon-strated that EFAL had no evident contribution to the zeolite acidity.     

Luminescence properties of [Ru(bpy)2MDHIP]2+ modulated by the introduction of DNA,copper(II) ion and EDTA

The luminescence properties of [Ru(bpy)₂MDHIP]²⁺ (bpy = 2,2′-bipyridine, MDHIP = 2,4-dihydrophenyl-imidazo[4,5-f][1,10]phenanthroline) in the absence and presence of DNA modulated by the introduction of Cu²⁺ ion and EDTA have been investigated. It is found that the ruthenium(II) complex can insert and stack between the base pairs of calf thymus DNA with MDHIP ligand, and the intramolecular hydrogen bond is located inside of the DNA. The presence of DNA can enhance the luminescence intensities of [Ru(bpy)₂MDHIP]²⁺ both in buffer solution and on an ITO surface. Moreover, the luminescence intensities of [Ru(bpy)₂MDHIP]²⁺ and DNA-bound [Ru(bpy)₂MDHIP]²⁺ are quenched by Cu²⁺, and next recovered by the addition of EDTA. The repetitive luminescence-modulations have been achieved through the introduction of equimolar Cu²⁺ and EDTA, respectively. In addition, it becomes evident that the number of luminescence-modulation cycles for [Ru(bpy)₂MDHIP]²⁺ in the absence and presence of DNA is influenced by the cumulative concentrations of CuEDTA, generated successively by the strong coordination of Cu²⁺ to EDTA.     

Two-dimensional layer architecture assembled by Keggin polyoxotungstate, Cu(II)-EDTA complex and sodium linker: Synthesis, crystal structures, and magnetic properties

Reaction of Keggin polyoxotungstate with copper(II)-EDTA (EDTA=ethylenediamine tetraacetate) complex under mild conditions led to the formation of hybrid inorganic-organic compounds Na₄(OH)[(Cu₂EDTA)PW₁₂O₄₀]·17H₂O (1) and Na₄[(Cu₂EDTA)SiW₁₂O₄₀]·19H₂O (2). The single-crystal X-ray diffraction analyses reveal their two structural features: (1) one-dimensional chain structure consisting of Keggin polyoxotungstate and copper(II)-EDTA complex; (2) Two-dimensional layer architecture assembled by the one-dimensional chain structure and sodium linker. The results of magnetic measurements in the temperature range 300-2 K indicated the existence of ferromagnetic exchange interactions between the Cu^II ions for both compounds. In addition, TGA analysis, IR spectra, and electrochemical properties were also investigated to well characterize these two compounds.     

Sensitized photo-redox reaction: VII. The Synthesis,FAB mass spectrum,stationary absorption,emission, transient absorption spectra,redox potential of dihydroxy-tin (IV)-mesoporphyrin dimethyl ester and its sensitized photo-reduction of methyl viologen

In DMSO/water (4:1), photolysis of the dihydroxy-Sn (IV)-mesoporphyrin dimethyl ester (SnP)/methyl viologen (MV²⁺)/ethylene diamine tetraacetic acid (EDTA) ternary system produces methyl viologen cation radical with a quantum yield of 0.67, much higher than that of systems with other metal complexes of mesoporphyrin dimethyl ester. Neither EDTA nor MV²⁺ quenches the stationary fluorescence of SnP, implying that the reaction does not take place at the singlet state. With flash photolysis we obtain the T-T absorption spectrum of SnP (λ_max 440 nm). By following the decay of this absorption, the triplet life time of SnP is estimated to be 41 μs. The life time is related to the concentration of either MV²⁺ or EDTA. Good linear relationships are obtained by plotting τ₀τ vs. the concentration of MV²⁺ or EDTA (Stern-Volmer plot), from which we determine the quenching constants: _kq(MV²⁺) =5.5 × 10⁷ mol^?1, s^?1; k_q (EDTA) =2.7 × 10⁷ mol^?1, s^?1. The data suggests that upon photolysis of the above ternary system, both oxidative quenching and reductive quenching of the triplet state of the sensitizer are occurring. From the measured phosphorescence spectrum (λ_max 704 nm) and the ground state redox, potentials (E^red_1/2?-0.84V, E^ox_1/2?+1.43 V, vs. Ag/AgCl, KCl (sat.)), we obtain the redox potential of triplet SnP to be E(P⁺/P*_T)?-0.33 V, E(P*_T+/P^?)?+0.92 V. Matching this data with the redox potential of MV²⁺ and EDTA, we establish the fact that during the photolysis of the SnP/MV²⁺/EDTA ternary system, both oxidative and reductive quenching are thermodynamically favorable processes. This is also the reason why the SnP sensitized reaction is much more efficient relative to other mesoporphyrin derivatives.     

Komplexone XL. Die Protonierungskonstanten einiger Komplexone in verschiedenen wässerigen Salzmedien (NaClO4, (CH3)4NCl,KNO3)

The protonation constants of the anions of thirteen polyaminocarboxylic acids have been determined in solutions containing different inert salts: KNO₃, NaClO₄ and N(CH₃)₄Cl. The formation constants of the following species: H₅EDTA+, H₆EDTA²⁺, H₅CDTA⁺ and H₄NTA⁺ have been obtained from solubility measurements with ethylenediamine tetraacetic acid (H₄EDTA), 1,2-diaminocyclohexane tetraacetic acid (H₄CDTA) and nitrilotriacetic acid (H₃NTA) in acid solutions between pH = 3 and 0 at ionic strength 1M (NaClO₄ + HClO₄).     

TiO2/EDTA-rich carbon composites: Synthesis,characterization and visible-light-driven photocatalytic reduction of Cr(VI)

TiO₂/EDTA-rich carbon composites exhibits excellent photoreduction of Cr(VI) activity via ligand-to-metal charge transfer process.     

Komplexone XLVI. EDTA-Komplexe des Pt(II)-Ions mit und ohne einzähnige Fremdliganden

The formation of complexes between Pt(II)EDTA^2? and H⁺, OH^?, Cl^?, Br^?, SCN^?, CN^? and NH₃ was investigated using pH and UV.-spectrophotometric measurements at ionic strength 1.0 and 25°. The existence of the following species could be proved (charges are omitted): H_pPt(EDTA) (0 ≤ p ≤ 3), Pt(EDTA)X (X = OH, NH₃, Cl, Br, I, SCN), H_pPt(EDTA)X (1 ≤ p ≤ 3; X = Cl, Br) and H₄Pt(EDTA)Cl₂. They have been characterised by spectral data as well as with equilibrium constants. The different modes of attachment of EDTA are discussed.     

Environmental Mobility of Pu(IV) in the Presence of Ethylenediaminetetraacetic Acid: Myth or Reality?

Ethylenediaminetetracetic acid (EDTA), which was co-disposed with Pu at several US Department of Energy sites, has been reported to enhance the solubility and transport of Pu. It is generally assumed that this enhanced transport of Pu in geologic environments is a result of complexation of Pu(IV) with EDTA. However, the fundamental basis for this assumption has never been fully explored. Whether EDTA can mobilize Pu(IV) in geologic environments is dependent on many factors, chief among them are not only the complexation constants of Pu with EDTA and dominant oxidation state and the nature of Pu solids, but also (1) the complexation constants of environmentally important metal ions (e.g., Fe, Al, Ca, Mg) that compete with Pu for EDTA and (2) EDTA interactions with the geomedia (e.g., adsorption, biodegradation) that reduce effective EDTA concentrations available for complexation. Extensive studies over a large range of pH values (1 to 14) and EDTA concentrations (0.0001 to 0.01 mol⋅L⁻¹) as a function of time were conducted on the solubility of 2-line ferrihydrite (Fe(OH)₃(s)), PuO₂(am) in the presence of different concentrations of Ca ions, and mixtures of PuO₂(am) and Fe(OH)₃(s). The solubility data were interpreted using Pitzer’s ion-interaction approach to determine/validate the solubility product of Fe(OH)₃(s), the complexation constants of Pu(IV)-EDTA and Fe(III)-EDTA, and to determine the effect of EDTA in solubilizing Pu(IV) from PuO₂(am) in the presence of Fe(III) compounds and aqueous Ca concentrations. Predictions based on these extensive fundamental data show that environmental mobility of Pu as a result of Pu(IV)-EDTA complexation as reported/implied in the literature is a myth rather than the reality. The data also show that in geologic environments where Pu(III) and Pu(V) are stable, the EDTA complexes of these oxidation states may play an important role in Pu mobility.     

Comparison of Cadmium Cd2+ and Lead Pb2+ Binding by Fe2O3@SiO2‐EDTA Nanoparticles – Binding Stability and Kinetic Studies

This study describes the synthesis and characterization of ethylenediaminetetraacetic acid (EDTA) functionalized magnetic nanoparticles of 20 nm in size – Fe₃O₄@SiO₂‐EDTA – which were used as a novel magnetic adsorbent for Cd(II) and Pb(II) binding in aqueous medium. These nanoparticles were obtained in two‐stage synthesis: covering by tetraethyl orthosilicate and functionalization with EDTA derivatives. Nanoparticles were characterized using TEM, FT‐IR, and XPS methods. Metal ions were detected under optimized experimental conditions using Differential Pulse Anodic Stripping Voltammetry (DPASV) and Hanging Mercury Drop Electrode (HDME) techniques. We compared the ability of Fe₃O₄@SiO₂‐EDTA to bind cadmium and lead in concentration of 553.9 μg L^?1 and 647.5 μg L^?1, respectively. Obtained results show that the adsorption rate of cadmium binding was very high. The equilibrium for Fe₃O₄@SiO₂‐EDTA‐Cd(II) was reached within 19 min while for the Fe₃O₄@SiO₂‐EDTA‐Pb(II) was reached within 25 minutes. About 2 mg of nanoparticles was enough to bind 87.5 % Cd(II) and 54.1 % Pb(II) content. In the next step the binding capacity of Fe₃O₄@SiO₂‐EDTA nanoparticles was determined. Only 1.265 mg of Fe₃O₄@SiO₂‐EDTA was enough to bind 96.14 % cadmium ions while 5.080 mg of nanoparticles bound 40.83 % lead ions. This phenomenon proves that the studied nanoparticles bind Cd(II) much better than Pb(II). The cadmium ions binding capacity of Fe₃O₄@SiO₂‐EDTA nanoparticles decreased during storage in 0.5 M KCl solution. Two days of Fe₃O₄@SiO₂‐EDTA storage in KCl solution caused the 32 % increase in the amount of nanoparticles required to bind 60 % of cadmium while eight‐days storage caused further increase to 328 %. The performed experiment confirmed that the storage of nanoparticles in solution without any surfactants reduced their binding capacity. The best binding capacity was observed for the nanoparticles prepared directly before the electrochemical measurements.     

Formation of heteropolynuclear cobalt(II) and nickel(II) complexonates with EDTA and 2-aminopropanoic acid

Coordination equilibria in the Co(II)–Ni(II)–2-aminopropanoic acid (HAla)–EDTA system have been studied spectrophotometrically at different molar ratios of the reagents in a wide pH range. It has been found that, when metal ions are in excess with respect to EDTA at pH 5–9, polyheteronuclear complexonates [(CoAla)Edta(NiAla)]^2–, [(CoAla₂)Edta(NiAla₂)]^4–, [(NiAla₂)Edta(CoAla₂)₂]^4–, [(CoAla₂)Edta(NiAla₂)₂]^4–, and [(NiAla₂)₂Edta(CoAla₂)₂]^4– form in a solution. The equilibrium constants of formation of these complexes and their overall stability constants have been calculated. Possible structures of the polynuclear complexonates are discussed.     

DIRECT OBSERVATION OF ELECTRON TRANSFER ACROSS A LIPID BILAYER: PULSED LASER PHOTOLYSIS OF AN ASYMMETRIC VESICLE SYSTEM CONTAINING CHLOROPHYLL,METHYL VIOLOGEN AND EDTA*

Abstract— Suspensions of vesicles composed of chlorophyll a (Chi) and phospholipid that were asymmetric with respect to aqueous solutions of methyl viologen (MV₂₊), an electron acceptor, and EDTA, an electron donor, were investigated using both flash and steady-state photolysis techniques. It was shown that Chl-photosensitized electron transfer occurred across the walls of the vesicles from EDTA to MV₂₊. Flash photolysis indicated that MV₂₊ dissolved in the interior aqueous compartments of the vesicles oxidized only those triplet excited state Chi molecules that were dissolved in the inner monolayers of the vesicle walls. The resultant radical products, Chi₊ and MV₊, recombined with a halftime of the order of 10_-4s. EDTA, added externally to the vesicles, competed effectively with MV₊ as a reducing agent for Chl₊. This places a lower limit of 10₄ s_-1 on the rate constant for transmembrane electron transfer. Compartmentalization by the vesicle wall of the competing pathways for the reduction of Chi₊ resulted in a nonlinear dependence of the rate constant of Chl₊ decay on EDTA concentration. The magnitude of the rate constant of electron transfer through the membrane and the way that the kinetics of Chl₊ decay depended on the concentration of Chi in the membrane strongly suggest that the electron transfer occurred by electron exchange between Chi and Chl₊.     

Morphology Control of Bi2S3 Nanostructures and the Formation Mechanism

Bismuthinite (Bi₂S₃) nanostructures were prepared by a hydrothermal method with sodium ethylenediaminetetraacetate (EDTA‐Na₂). The morphology of Bi₂S₃ nanostructures was changed from a nanorod to a nanoplate by presence of the EDTA‐Na₂. The altered morphology was caused by the capping effect of EDTA‐Na₂ with Bi³⁺ ions, which induces the suboptimal growth direction due to partially blocking the preferential orientation direction. When the EDTA‐Na₂/Bi³⁺ molar ratio=1, the growth of Bi₂S₃ nanostructures was not allowed due to the chelating effect of EDTA‐Na₂. The obtained Bi₂S₃ nanorods, stacked nanorods, nanoplates and nanoparticles were characterized using X‐ray diffraction (XRD), transmission electron microscopy (TEM), high‐resolution transmission electron microscopy (HRTEM) and selected area electron diffraction (SAED) pattern. A possible formation mechanism of these morphologies was proposed. The successful synthesis of various morphologies of nanostructured Bi₂S₃ may open up new possibilities for thermoelectric, electronic and optoelectronic uses of nanodevices based on Bi₂S₃ nanostructure.     

Effect of Complexation on Photocatalytic Degradation of Dissolved Organic Nitrogen Compounds

Abstract

The effect of metal ions on TiO₂ mediated photocatalytic oxidation for the determination of dissolved organic nitrogen compounds is investigated. Ethylenediaminetetraaceticacid was chosen as a model molecule for DON compounds. At pH 2, 5, 7, and 10 aqueous EDTA solutions were irradiated at 254 nm in the presence of Fe²⁺, Cu²⁺, Zn²⁺, Ni²⁺ or Co²⁺ ions. The sum of produced nitrate, nitrite, and ammonium ion concentrations gave the total oxidation recovery. At low pH, the photocatalytic oxidation recoveries of Fe‐EDTA, Ni‐EDTA, and Co‐EDTA were significantly lower than the photocatalytic degradation of EDTA. The presence of free Fe²⁺, Ni²⁺, and Co²⁺ ions decreased the photocatalytic oxidation recovery. The [NH₄ ⁺]/[NO₃ ^?] ratio was higher for Cu‐EDTA.     

Novel ruthenium based electrocatalyst for the convenient reduction of nitrogen-nitrogen bonds in azide to ammonia in aqueous solution

The interaction of azide (N ₃ ⁻ ) ion, at pH 5.3 with [Ru^III(EDTA) (H₂O)]⁻ (EDTA = ethylenediaminetetraacetate) was studied in aqueous solution by polarography and cyclic voltammetry. The product, [Ru^III(EDTA)(N₃)]²⁻ showed a multi-electron reduction step, which is polarographically reversible but, cyclic voltammetrically irreversible, in the potential range − 0.1 to − 0.2 V vs SCE. This reduction step, which was different from the one-electron reduction step of [Ru^III(EDTA)(H₂O)]; (E^1/2 = −0.113V vs SCE) was assigned to the reduction of the coordinated azide ion to ammonia by the irreversible transfer of electrons from Hg-electrode via ruthenium metal. Azide, at pH 5.3, was reduced, electrolytically, for the first time, to ammonia at Hg-pool cathode mediated by [Ru^III(EDTA) (N₃)]²⁻. The turnover number with respect to the formation of ammonia (moles of ammonia per mole of ruthenium per hour) was obtained from the constant potential electrolysis data. On the basis of experimental observations, a probable mechanism has been proposed for the electrocatalytic reduction of azide to ammonia in aqueous solution.     

Ion-chromatographic determination of divalent metal ions (Co, Ni, Cu, Zn, Cd) using EDTA as complexing agent

Summary Metal ions, such as cobalt, nickel, copper, zinc and cadmium, were separated as the anionic metal-EDTA complexes using an ion-chromatograph equipped with anion separator system. The separated complex anions in the eluent (3×10^–3 M NaHCO₃/2.4×10^–3 M Na₂CO₃) were detected by conductivity measurement. When 100 l of the sample solution containing 10^–4 M EDTA was introduced into the analytical system, up to 5.0 ppm of metal ions were determined. The method was applied to the determination of metal ions in plating solution and waste water samples. When the sample solution was introduced into the system, a chromatogram of anions in the sample was obtained. Then the sample solution with EDTA was introduced and a chromatogram of anions and metal-EDTA complexes was obtained. The metals were determined from the difference of the former and the latter chromatograms.

---

Ionen-chromatographische Bestimmung von zweiwertigen Metallionen (Co, Ni, Cu, Zn, Cd) mit Hilfe von EDTA als Komplexierungsmittel

Zusammenfassung Die Metallionen wurden als anionische Metall-EDTA-Komplexe getrennt, wobei ein Ionenchromatograph mit Anionenseparatorsystem benutzt wurde. Die getrennten Anionenkomplex-Ionen wurden im Eluat (3 · 10^–3 M NaHCO₃/2,4 · 10^–3 M Na₂CO₃) durch Leitfä-higkeitsmessung erfaßt. In 100 l Probelösung mit 10^–4 M EDTA konnten 5,0 ppm Metall bestimmt werden. Das Verfahren wurde auf galvanische Lösungen und Abwasser angewendet. Bei Einführung der Probelösung in das System erhält man ein Chromatogramm der vorhandenen Anionen. Wenn dann Probe + EDTA injiziert wird, ergibt sich ein Chromatogramm der Anionen und Metall-EDTA-Komplexe. Die Metallgehalte resultieren aus der Differenz.

     

Electrothermal atomic absorption spectrometric determination of trace lead,copper and manganese in aluminum and its alloys without preliminary separation

Graphite-furnace atomic absorption spectrometry is used for the determination of >0.001% of lead, copper and manganese in aluminum and its alloys. The samples are dissolved in hydrochloric acid and analyzed directly after addition of a slight excess of (NH₄)₂ EDTA over aluminum. Sample and standard solutions must contain equal amounts of EDTA.     

改性H-ZSM-34上氯甲烷催化转化制低碳烯烃

比较了几种典型的沸石分子筛在氯甲烷转化制乙烯、丙烯和丁烯等低碳烯烃反应中的催化性能, 发现H-ZSM-34具有较佳的催化活性和选择性. 经乙二胺四乙酸二钠(Na₂H₂EDTA)水溶液处理, 并经离子交换及焙烧后, H-ZSM-34上氯甲烷转化制低碳烯烃的催化性能显著改善. 当Na₂H₂EDTA浓度为0.1 mol/L, 反应温度为673 K, CH₃Cl分压9.2 kPa时, C₂-C₄烯烃选择性和收率分别达82%和61%. 研究还发现, Ce修饰H-ZSM-34催化剂同样可改善氯甲烷制低碳烯烃的选择性和收率. 表征结果表明, Na₂H₂EDTA处理和Ce修饰均降低了H-ZSM-34的酸性. 酸性的降低可抑制低碳烯烃的氢转移反应, 继而避免了其进一步转化为低碳烷烃.     

Electrochemical detection of the explosive, hexamethylene triperoxide diamine (HMTD)

A rapid electrochemical detection scheme for the improvised explosive, hexamethylene triperoxide diamine (HMTD) is demonstrated. This is based on the hydrolysis of HMTD releasing H₂O₂ and the electrochemical redox cycling of Fe^II/IIIEDTA via the following scheme:

Fe^IIIEDTA + e⁻→Fe^IIEDTA     

Hydrothermal synthesis and extended structure of poly[aqua(μ5‐ethylenediaminetetraacetato)dizinc(II)]

In the extended structure of the title compound, [Zn₂(C₁₀H₁₂N₂O₈)(H₂O)], prepared under hydrothermal conditions, there are two distinct Zn^II sites. The first, with octahedral geometry, bonds to two N and three O atoms from one ethylenediaminetetraacetate tetraanion (EDTA) and one water molecule. The second, with tetrahedral geometry, coordinates to O atoms from four different EDTA ligands. The EDTA ligand almost encapsulates the octahedral Zn^II ion and binds to four symmetry‐related tetrahedral Zn^II ions, hence generating the extended structure. One noncoordinated O‐atom site on the EDTA ligand connects to the water molecule by hydrogen bonding. Structural comparisons are made with other compounds containing zinc, EDTA and water.