Spectrophotofluorometric determination of terbium and europium in potassium carbonate solution

The conditions for the spectrophotofluorometric determination of terbium and europium, in solutions of potassium carbonate, have been established. The apparent excitation and fluorescence wavelengths used, respectively, are 245 mmu and 550 mmu for terbium and 400 mmu and 620 mmu for europium. The fluorescence varies linearly with the concentration of terbium and europium in the range 0.3-70 mug, of terbium/ml and 4-800 mug of europium/ml. Large amounts of gadolinium, lutetium and yttrium do not interfere. Cerium(IV) interferes seriously.     

Luminescent properties of silica and zirconia xerogels doped with europium(III) salts and europium(III) cryptate incorporating 3,3-biisoquinoline-2,2-dioxide

Eu⁺³ cryptate with 3,3^′-biisoquinoline-2,2^′-dioxide unit was incorporated into glass films consisting of zirconia dioxide and into hybrid ormosil films. The absorption and the emission intensities of the europium complex were compared to the intensity of the non-complexed europium ion in the films. The transition probabilities of the complex are increased as a result of the mixing of the europium orbitals with the ligand orbitals. The emission is additionally increased as the non-radiative relaxation is diminished by the cage effect.     

Ion beam induced emissions from solid europium compounds

Impact of energetic heavy particles on europium compound surfaces gives rise to radiative optical emission from reflected and sputtered particles and from the excited states of the solid compounds. In the present paper we discuss the optical spectrum and the sputtered secondary ion mass spectrum observed when solid europium oxide (Eu₂O₃) and europium chloride (EuCl₃) are bombarded with 90 keV Ar⁺ ions from an ion accelerator. We observe the reduction reaction in solid europium chloride (EuCl₃) by bombardment with a 20 A/cm² beam of 90 keV Ar⁺ ions.     

Cathodic europium(III) electroluminescence at an oxide-coated aluminum electrode

Electroluminescence is produced at an oxide-coated aluminum electrode during cathodic polarization of the electrode in an acetate solution containing nitrate and traces of europium(III). The europium(III) ion in the ⁵D₀ state is the emitter. Linear log-log calibration plots are obtained for the range 1 × 10^?8?1 × 10^?5 M europium(III). A mechanism for the cathodic luminescence is proposed.     

Luminescence and magnetic properties of europium(III) nitrate complex with 1,10-phenanthroline

Luminescent and magnetic properties of the europium nitrate complex with 1,10-phenanthroline synthesized in the traditional way by precipitation from water-ethanol medium and by the method of mechanical activation were investigated. Correlations between luminescent and magnetic properties of the complex compounds were revealed. The higher value of molar magnetic susceptibility ??_m was shown to be typical for the highly dispersed europium compound obtained by mechanochemistry method due to the presence of the paramagnetic ion Eu²⁺.     

A study of the fluorescence of some newly synthesized europium complexes with pyrazolone derivatives

Some europium complexes with pyrazolone derivatives and 1,10-phenanthroline were synthesized and characterized. The europium ion was found to coordinate to O atoms of the pyrazolone derivatives and to N atoms of 1,10-phenanthroline. A strongly ligand-localized UV absorption leads to the europium-centered emissions between 580 and 750 nm which were assigned as the 5D0-->7F0,1,2,3,4 and 5D1-->7F3,4 transitions. A low site symmetry for the Eu3+ ion was confirmed from the observation of 5D0-->7F0 emission and from the splitting of the other bands. In contrast to many Eu complexes that have been investigated a rather weak emission was measured by introduction of a Schiff base to form a ternary complex with the pyrazolone derivative. The long fluorescence lifetimes of these complexes suggest an energy transfer process from ligands to Eu3+ ion through the triplet state of the ligands.     

Intramolecular energy-transfer in a europium(III) chelate with salicylidene-valinate schiff base

Summary An intense fluorescence,⁵D⁷F, of the europium(III) ion was observed at room temperature in DMSO and DMF solutions of the europium(III) chelate with salicylidene-valinate Schiff base, as a result of an intramolecular energy-transfer from the ligand to the metal ion. The metal chelate has been characterized and appears to possess an octahedral configuration. These results offer an interesting opportunity to probe the active sites of pyridoxal enzymes.     

Synthesis and spectroscopic studies of europium chelate complexes

The synthesis of the mixed complexes of the europium ion with 2-pyridylcarbinol-N-oxide, and 2,2′-dipyridyl and 1,10-phenanthroline were prepared. The compounds, were characterized by means of chemical analyses, vibrational spectra, molar conductivities, and electronic spectra. The emission of the [EuL₃, phen] complex at 10 K is very intense and an assignment of the point symmetry of the Eu(III) ion has been made.     

Synthesis and luminescence of zinc and europium alpha-thiophene carboxylate polymer

The zinc and europium alpha-thiophene carboxylate polymer with very strong red luminescence was prepared by rheological phase reaction method from zinc acetate, europium oxide and alpha-thiophenecarboxylic acid. Molecular weight, thermal analyses and X-ray diffraction pattern were measured. 1H NMR, 13C NMR, IR, XPS, UV, excitation and emission spectra were studied. The polymer with amorphous structure and 7.565x10(5) g/mol weight-average molecular exhibited excellent solubility in common organic solvents and better thermal stability under 270 degrees C in air. The quantum yield of the polymer in acetone was 0.6 relative to quinoline in 0.05 mol/l H(2)SO(4) solution. The energy of the pi,pi(*) excited state of C(4)H(3)SCO(2)(-) can be transferred to Eu(3+) ion resulting in emission from the 5D(0)-->(7)F(j) of Eu(3+) ion through the polymeric chains. Zn(2+) can effectively enhance the luminescence of Eu(3+) in alpha-thiophenecarboxylate polymer.     

Identification of luminescent europium beta-diketonates using high-resolution emission spectrometry and direct-inlet electron ionization mass spectrometry.

The high-resolution emission spectra measured using a microscope Raman spectrometer and direct-inlet electron ionization mass spectrometry (DI-EIMS) were studied for the rapid analysis of a trace amount of various europium beta-diketonates in order to utilize them as fluorescent markers. Five kinds of europium beta-diketonates were distinguished from the emission spectra obtained using the Raman spectrometer. For DI-EIMS, the electron ionization mass spectra of the europium beta-diketonates showed the characteristic fragment ion peaks due to the isotope effect of 151Eu and 153Eu. The DI-EIMS was very useful for identifying the compounds compared with spectrofluorometry. The scan and selected ion-monitoring modes of DI-EIMS showed the detection limits of the samples at levels of hundreds and tens of nanograms (ng), respectively.     

Synthesis, structure and luminescence property of the ternary and quaternary europium complexes with furoic acid

A ternany europium complex with furoic acid (α-FURA) and 1,10-phenanthroline(phen), [Eu(α-FURA)₃phen]H₂O(I) and a quaternary europium furoate complex with 1,10-phenanthroline and nitrate, Eu(α-FURA)₂NO₃phen(II) were synthesized and characterized by X-ray diffraction. The two europium ions in each of the complexes (I) and (II) are held together by four carboxylato groups with the two modes, namely bidentate bridging and tridentate bridging, and each europium ion is further bonded to two nitrogen atoms from 1,10-phenanthroline and one chelated bidentate furoate group for the complex (I) and one chelated nitrato group for the complex (II), making a coordination number of 9. Luminescence spectra observed at 77 K show that the europium ion site in the crystals of the complexes (I) and (II) has low symmetry and lifetimes of the solid complexes (I) and (II) are 1.13 and 1.20 ms, respectively.     

The luminescent properties of divalent europium complexes of crown ethers and cryptands

The luminescent properties of divalent europium complexes with crown ether, azacrown ether, N-pivot-azacrown ether, and cryptand in methanol or water have been systematically investigated under UV irradiation. These divalent europium complexes show greatly enhanced emission from 417 nm to 488 nm in the visible blue region in comparison with that of the methanol solution of EuCl₂. The aqueous solution of EuCl₂ is non-luminescent. This obvious distinction in luminescent properties between the macrocyclic ligand-coordinated divalent europium and uncoordinated divalent europium is attributed to the “insulation effect” of Eu²⁺ ion from the solvent molecules of CH₃OH and H₂O by the macrocyclic crown ether or cryptand encapsulation to divalent europium. Moreover, these macrocyclic ligands provide an additional restriction to the electronic charge expansion of the excited Eu²⁺. This also contributes to the enhancement of the Eu²⁺ luminescence. Among all the investigated macrocyclic ligands, 15-crown-5 (15C5) affords the largest enhancement to the Eu²⁺ emission. The intensity of the Eu²⁺–15C5 complex is 690 times that of the EuCl₂ methanol solution with the same Eu²⁺ concentration. This special emission enhancement effect is related to the particular complex composition of 1:3 (Eu²⁺:15C5) and corresponding configuration of Eu²⁺–15C5 complex in methanol. Concerning the mechanism, the luminescence enhancement of divalent europium by complexation with these macrocyclic crown ether or cryptand ligands is found to be initiated from the decrease in non-radiative rate constant rather than from the increase in radiative one.

The divalent europium complexes of methacrylate polymeric polyether derivatives such as 15C5-, 18-crown-6- (18C6), and cryptand [2.2.1]- or [2.2.2]-containing polymer and copolymer have also been prepared. Their luminescent properties in solid state have been studied to aim for practical application. As a similar situation to the simple polyether complexes, the divalent europium complex with 15C5-containing polymer or copolymer shows the largest luminescent enhancement effect. Its emission intensity reaches about 20% that of the commercial inorganic luminescence product CaWO₄:Pb (NBS 1026). In addition, the doping effect of several divalent ions, namely Mg, Sr, Ba and Zn in polymeric complexes, has also been investigated according to the luminescence concentration quenching mechanism in solid state luminescence materials. The emission intensity of 15C5-containing polymer europium(II) complex is raised to twice stronger by doping of Zn²⁺ ion.     

Luminescent and triboluminescent properties of europium(III) complex with cinnamic acid

An intensely emitting crystalline europium(III) complex with cinnamic acid [Eu(Cin)₃] _n and exhibiting triboluminescent properties is synthesized. It is established that the measured photo- and triboluminescence spectra are identical for the above polymeric non-centrosymmetric complex and are determined by the characteristic f-f luminescence of the europium(III) ion.     

Synthesis and fluorescent properties of europium complexes with amide-type podand ligands of methyl salicylate

Amide-type podands derived from N,N′-(ethane-1,2-diyl)bis(2-hydroxybenzamide) and 2-chloro-N-phenylacetamide (substituted with methyl, methoxy, chlorine, nitrogen) were synthesized. Solid complexes of europium nitrate with podands were also synthesized and characterized by elemental analysis, ethylenediaminetetraacetic acid (EDTA) titrimetric analysis, thermal analysis, molar conductivity analysis, and infrared (IR) and ultraviolet–visible (UV–Vis) spectra analysis. The fluorescent properties of the europium(III) [Eu(III)] complexes in a solid state were also investigated. Under excitation of UV light, target Eu(III) complexes exhibited characteristic europium ion emissions. The influence of the substituent on the fluorescence intensity was discussed. Electrochemical properties were also investigated and discussed.     

Simultaneous time-resolved fluorescence and thermal lens measurements: Application to energy transfer studies in europium chelates

Simultaneous time-resolved fluorescence and thermal lens measurements are applied to the study of europium chelates in methanol, ethanol and acetonitrile. The intramolecular energy transfer from the ligand to the ion results in a strong increase in europium fluorescence. Simultaneously, a slow rising component of the order of microseconds is observed on the thermal lens curve. Both events are respectively related to radiative and non-radiative relaxation of the long-lived ⁵D₀ state of europium ions.     

Extraction of europium complexes with 1,2,4,5-benzenetetracarboxylic acid and neutral ligands

Extraction of mixed-ligand europium complexes with 1,2,4,5-benzenetetracarboxylic (pyromellitic) acid and neutral ligands was studied. The complexation of europium with the ligands is discussed on the basis of data on europium distribution in extraction systems, as well as IR and luminescent spectroscopy data of extracts. Crystalline polynuclear europium complexes with pyromellitic acid and 1,10-phenanthroline and tris(hydroxymethyl)aminomethane were isolated from the extracts. The composition of pyrolysis products of extracts was studied. It was shown that nanosized bulk samples of europium oxide can be obtained by the pyrolysis of saturated extracts. Differences in the morphology of europium oxide nanoparticles were revealed in the samples obtained by pyrolysis of extracts differing in composition at the same temperature and time.     

Indirect photometric determination of europium(II) in some inorganic materials containing aliovalent europium species

A procedure is proposed for the indirect spectrophotometric determination of trace europium(II) in poorly soluble inorganic materials. The approach based on sample dissolution in the presence of excess vanadium(V) salts followed by the determination of vanadium(IV), equivalent to the concentration of europium(II), is used. The photometric determination of V(IV) is based on its oxidation with a potassium permanganate solution followed by the measurement of absorbance of excess MnO₄⁻. The procedure is applied to the analysis of EuF_{3 − x} with low europium(II) concentrations in the study the dissolution products of europium fluorides in salt melts and in the study the products of sorption europium(II) by strontium fluorapatite from salt melts. The proposed procedure is rapid and simple. It possesses satisfactory performance characteristics.     

Photodegradation and photostabilization of europium compounds in polyvinyl chloride

The photolysis kinetics was studied, and methods were suggested for photostabilization of complexes of europium with β-diketones and europium cinnamates and quinaldates in polyvinyl chloride.     

Cation-controlled self-assembly of a hexameric europium wheel

The simple asymmetric tetradentate ligand 2,2':6',2' '-terpyridine-6-carboxylic acid leads to the self-assembly of the first europium nanowheel containing europium ions in two different coordination environments. Moreover the self-assembly of bis(terpyridinecarboxylate) europium species to form a hexameric wheel capable of strongly binding LnIII cations is controlled by the ligand/cation ratio.     

Sorption of europium on zirconium oxide from aqueous solutions

Sorption of europium on zirconium oxide has been studies as a function of shaking time, concentration and nature of electrolyte. The effect of initial europium concentration and the amount of adsorbent has been investigated in the range from 6.6·10^–10 to 6.6·10^–8 mol·dm^–3 and between 10 to 200 mg of the oxide. Maximum sorption (>99.8%) from pH 10 buffer and low sorption (<3%) was observed from 0.01 mol·dm^–3 nitric or perchloric acid solution. Citrate, sulfate, EDTA and carbonate reduced the sorption significantly. Under optimal conditions Ag(I), Cs(I), Tc(VII), Sb(V), Cu(II), Nd(III), Fe(III), and especially Nd and Fe showed low distribution coefficients. The data followed both Dubinin-Radushkevich and Langmuir-type isotherms. The mean free energy, of sorption was evaluated to be 10.1 kJ mol^–1 and the sorption capacity was found to be 22.2 mmol g^–1, using the Dubinin-Radushkevich isotherm.