Simultaneous Determination of Paracetamol and Orphenadrine Citrate in Dosage Formulations and in Human Serum by RP‐HPLC

Rapid liquid chromatographic procedures are proposed for analysis of paracetamol and orphenadrine citrate in pharmaceutical preparations and human serum using acetonitrile: water (50:50) as a mobile phase, adjusting pH to 2.6, UV detection at 215 nm and propylparaben sodium as internal standard. The advantages of this method include good and rapid separation, well resolved peaks, and only a small amount of sample is required for assay and adequate precision. The method showed good linearity in the range of 6 to 10000 ng/mL for paracetamol serum concentrations with a correlation coefficient 0.9999 (inter and intra day CV < 3.15) and in the range 3–10000 ng/mL for orphenadrine citrate serum concentrations with a correlation coefficient of 0.9999 (inter and intra day CV < 3.58). The recovery of paracetamol and orphenadrine citrate was > 96.9% and > 96.7%, respectively. The proposed method may be used for the quantitative analysis of paracetamol and orphenadrine citrate alone or in combination from raw materials, in bulk drugs, dosage formulations and in serum.     

Simultaneous Determination of Prazosin,Atorvastatin, Rosuvastatin and Simvastatin in API,Dosage Formulations and Human Serum by RP‐HPLC

Prazosin hydrochloride is the first developed selective antagonist for α₁ — adrenoceptors, which is used as antihypertensive agent. Statins are used in the treatment of various types of hypercholesterolemia. In the present paper a simple, specific an accurate RP‐HPLC method was developed and validated for the simultaneous determination of prazosin, atorvastatin, rosuvastatin and simvastatin in active and in dosage formulations. A nucleosil 100‐10, C‐18, 10μ column having 250 × 4.6 mm i.d. in isocratic mode, with mobile phase containing methanol:water:acetonitrile (70:20:10) adjusted to pH 2.5 ± 0.02 using orthophosphoric acid. The flow rate was 1 mLmin^?1 and effluents were monitored at 240 nm. The % recovery for all the drugs in formulations was found to be 94‐105%. The parameters such as accuracy (%RSD less than 2), precision (%RSD less than 2), linearity (>0.999) were found to be satisfactory. The presented method was applied without any interference of excepients for the determination of tablets. The proposed method due to its low LOQ, excellent accuracy, precision and selectivity could be used for routine quality control.     

Simultaneous Determination of Ceftriaxone Sodium and Non Steroidal Anti‐Inflammatory Drugs in Pharmaceutical Formulations and Human Serum by RP‐HPLC

An accurate, sensitive and least time consuming reverse phase high performance liquid chromatographic (RP‐HPLC) method for the estimation of ceftriaxone in the presence of non steroidal anti‐inflammatory drugs in formulation and human serum has been developed and validated. Chromatographic separation was conducted on prepacked Purospher Star, C18 (5 μm, 250 × 4.6 mm) column at room temperature using methanol:water:acetonitrile (80:15:5 v/v/v) as a mobile phase, pH adjusted at 2.8 with ortho‐phosphoric acid and at a flow rate of 1.0 mL/minute, while UV detection was performed at 270 nm. The results obtained showed a good agreement with the declared content. The method shows good linearity in the range of 2.5‐25 μg/mL ceftriaxone serum concentrations with a correlation coefficient 0.999 (inter‐ and intra‐day RSD < 2.0%). The limit of detection and quantification for ceftriaxone and NSAID's in pharmaceutical formulation and serum were in the range 0.51‐1.54 μg/mL. Analytical recovery was >98.1%. The proposed method may be used for the quantitative analysis of commonly administered non steroidal anti‐inflammatory drugs i.e. tiaprofenic acid, naproxen sodium, flurbiprofen, diclofenac acid and mefenamic acid alone or in combination with ceftriaxone from raw materials, dosage formulations and in serum. The established HPLC method is rapid, accurate and selective, because of its sensitivity and reproducibility.     

Simultaneous Quantitation of Captopril and NSAID's in API,Dosage Formulations and Human Serum by RP‐HPLC

An accurate, sensitive and least time consuming reverse phase high performance liquid chromatographic (RP‐HPLC) method for the estimation of captopril in the presence of non steroidal anti‐inflammatory drugs in formulation and human serum has been developed and validated. Chromatographic separation was conducted on prepacked Purospher star C18 (5 μm, 25 × 0.46 cm) column at room temperature using methanol:water (80:20 v/v) as a mobile phase, pH adjusted at 2.8 with o‐phosphoric acid and at a flow rate of 1.0 mL min⁻¹, while UV detection was performed at 227 nm. The limit of detection and quantification for captopril were 1 and 0.35 ng mL⁻¹, while that for (NSAID's) i.e. flurbiprofen, ibuprofen, diclofenac sodium and mefenamic acid LOD were 0.2, 1, 2 and 0.4 ng mL⁻¹ respectively and LOQ were 0.9, 2.9, 8 and 1 ng mL⁻¹ Analytical recovery was > 98.1%. The method used for the quantitative analysis of commonly administered non steroidal anti‐inflammatory drugs (NSAID's) i.e. ibuprofen, flurbiprofen, diclofenac sodium and mefenamic acid alone or in combination with captopril from API (active pharmaceutical ingredients), dosage formulations and in human serum. The established method is rapid (RT < 12 min), accurate (recovery > 98.1%), selective (no interference of excepients and other commonly used drugs and food) and sensitive (LOQ 3.5 ng mL^;‐1) and reproducible (SD ± 0.003).     

Validated Method for the Simultaneous Determination of Lisinopril,Pravastatin, Atorvastatin and Rosuvastatin in API,Formulations and Human Serum by RP‐HPLC

Lisinopril is found to be useful in hypertension and statins as cholesterol lowering drug. Present work was designed for the simultaneous determination of lisinopril in presence of pravastatin, atorvastatin, and rosuvastatin using RP‐HPLC method. A Purospher star C18 (5 μm, 25×0.46 cm) column was used with mobile phase consisting of acetonitrile:water (60:40 V/V, pH 3.0) with flow rate of 1.0 mL·min^?1 and the quantitative evaluation was performed at 225 nm. The retention time of lisinopril was 2.0 min and for pravastatin, rosuvastatin and atorvastatin was found to be 3.1, 4.5 and 8.3 min respectively. Suitability of this method for the quantitative determination of the drugs was proved by validation in accordance with the requirements laid down by International Conference on Harmonization (ICH) guidelines. Application of the suggested procedures were successfully applied to the determination of these compounds in active pharmaceutical ingredient and in pharmaceutical preparations, with high percentage of recovery, good accuracy and precision.     

Simultaneous Determination of Atenolol,Rosuvastatin, Spironolactone,Glibenclamide and Naproxen Sodium in Pharmaceutical Formulations and Human Plasma by RP‐HPLC

A rapid and sensitive high‐performance liquid chromatographic method was developed and validated for the simultaneous determination and quantification of atenolol, rosuvastatin, spirnolactone, glibenclamide and naproxen sodium in bulk drugs, pharmaceutical formulations and in human plasma in the presence of internal standard (flurbiprofen). Chromatograms were developed with methanol and water (80:20, v/v) solvent system on a Purospher start, C₁₈ (5 μm, 250 × 4.6 mm) column and pH was adjusted to 3.40 with ortho‐phosphoric acid. Mobile phase was pumped with a flow rate of 0.90 mL/minute with 235 nm UV detection. Standard curves were linear over the concentration range 0.25‐30 μg/mL^?1. The coefficients of variation (C.V.%), were < 3% and LOD and LOQ were <0.0154 & 0.06 for inter‐ and intra‐day, respectively. The method was applied to drug interaction studies of atenolol with rosuvastatin, spironolactone, glibenclamide and naproxen to illustrate the scope and application of the methods to manage four different therapeutic classes of drugs, as they are co‐administered.     

Simultaneous Determination of Tin,Nickel, Lead,Cadmium and Mercury in Tobacco and Tobacco Additives by Microwave Digestion and RP‐HPLC Followed by On‐Line Column Enrichment

A new method for the simultaneous determination of five heavy metal ions, tin, nickel, lead, cadmium and mercury ions as metal‐tetra‐(2‐aminophenyl)‐porphyrin (T₂APP) chelates was developed using reversed‐phase high performance liquid chromatography (RP‐HPLC) equipped with a photodiode array detector and combined with an on‐line enrichment technique. The tin, nickel, lead, cadmium and mercury ions were pre‐column derivatized with T₂APP to form color chelates. The Sn‐T₂APP, Ni‐T₂APP, Hg‐T₂APP, Cd‐T₂‐APP and Pb‐T₂APP chelates can be absorbed onto the front of the enrichment column when they are injected into the injector and sent to the enrichment column [Waters Xterra? RP₁₈(5μ, 3.9 × 20 mm)] with a buffer solution of 0.05 mol/L pyrrolidine‐acetic acid (pH = 10.0) as mobile phase. After the enrichment had finished, by switching the six‐port switching valves, the retained chelates were back‐flushed by mobile phase and traveling towards the analytical column. These chelates separation on the analytical column [Waters Xterra? RP₁₈ (5μ, 3.9 × 150 mm)] was satisfactory by gradient elution with methanol (containing 0.05 mol/L pyrrolidine‐acetic acid buffer salt, pH = 10.0) and acetone (containing 0.05 mol/L pyrrolidine‐acetic acid buffer salt, pH = 10.0) as mobile phase. The linearity range is 0.01?120 μg/L for each metal ion. The detection limits (S/N = 3) of tin, nickel, lead, cadmium and mercury are 4.0 ng/L, 3.5 ng/L, 2.5 ng/L, 3.0 ng/L and 3.0 ng/L, respectively. This method was applied to the determination of tin, nickel, lead, cadmium and mercury ions in tobacco and tobacco additives with good results.     

Study on Determination of Six Transition Metal Ions in Biological Samples by SPE and RP‐HPLC

This paper reports the utilization of solid phase extraction and the reversed‐phase high‐performance liquid chromatography (RP‐HPLC) for the determination of six transition metal ions (iron, cobalt, nickel, copper, zinc and manganese) in biological samples. The samples were digested by microwave digestion. The iron, cobalt, nickel, copper, zinc and manganese ions in the digested samples can react with 2‐(2‐quinolinylazo)‐5‐diethylaminophenol (QADEAP) to form colored chelates in pH 4.0 acetic acid‐sodium acetic buffer solutions and cetyl trimethylammonium bromide (CTMAB) medium. These chelates were enriched by solid phase extraction with C₁₈ cartridge. Then the chelates were separated on a Waters Nova‐Pak‐C₁₈ column (3.9 × 150 mm, 5 μm) by gradient elution with methanol (containing 0.5% of acetic acid and 0.1% of CTMAB) and 0.05 mol/L pH 4.0 acetic acid‐sodium acetic buffer solution (containing 0.1% of CTMAB) as mobile phase at a flow rate of 0.5 mL/min. The detection limits of iron, cobalt, nickel, copper, zinc and manganese are 3 ng/L, 4 ng/L, 2 ng/L, 4 ng/L, 8 ng/L, 10 ng/L, respectively. This method was applied to the determination of iron, cobalt, nickel, copper, zinc and manganese in biological samples with good results.     

Lipophilicity determination of N-( benzothiazol-2-yl )-α-amino alkyl phosphonic diesters by RP-HPLC and RP-HPTLC

Using methanol-water mixtures as the mobile phase,the chro-matographic retention parameters k' and Rf were determined by reversed-phase high-performance liquid chromatography(RP-HPLC)and reversed-phase high-performance thin-layer chromatography(RP-HPTLC)for N-(benzothiazol-2-yl)-o) amino alkyl phosphonic diesters and the correlation with lipophilicity parameter(ClogP)was established.Logkw values obtained from RP-HPLC and R values obtained from RP-HPTLC can be used to evaluate the lipophilicity of this kind of compounds.Chromatographic method is a good alternative for lipophilicity measurement.     

Determination of Melatonin Hormone in Bulk Form,Tablets and Human Serum by Square‐Wave Cathodic Adsorptive Stripping Voltammetry

Melatonin hormone plays an important role in many distinct physiological functions. A fully validated, sensitive and reproducible square‐wave cathodic adsorptive stripping voltammetric procedure was described for determination of melatonin in bulk form, tablets and human serum. The procedure was based on the reduction of the adsorptive hormone onto a hanging mercury drop electrode. Reduction behavior of melatonin was studied in both Britton‐Robinson (pH 2–11) and acetate (4.5–5.5) buffers. Acetate buffer of pH 5.0 was found reasonable as a supporting electrolyte for assay of the drug. The square‐wave cathodic adsorptive stripping voltammogram of melatonin showed a single well‐defined peak at ?1.45 V (vs. Ag/AgCl/KCl_s) using an accumulation potential of ?0.65 V. This peak may be attributed to the reduction of C?O double bond of the amide functional group of the reactant molecule. A mean recovery for 1×10^?8 M melatonin in bulk form followed 30 s accumulation of 98.87%±0.78 and a detection limit of 3.13×10^?10 M were achieved. The proposed procedure was successfully applied for the determination of the drug in tablets and human serum with mean recoveries of 97.68%±0.57 and 101.67%±0.85, respectively. A detection limit of 8.80×10^?10 M was achieved for the determination of the drug in human serum. Results of the proposed method were comparable and coincided with those obtained by reported method. Vitamin B₆ and common excipients, which are co‐formulated with melatonin, did not interfere. Also the effect of some interfering compounds such as serotonin, tryptophan and 5‐hydroxytryptophan on the determination of melatonin in human serum was studied, and all have no significant effect on the assay recovery.     

Indirect enantioresolution of (R,S)‐mexiletine by reversed‐phase high‐performance liquid chromatography via diastereomerization with [(S,S)‐O,O'‐di‐p‐toluoyl tartaric acid anhydride], (S)‐naproxen and nine chiral reagents synthesized as variants of Marfey's reagent

Eleven chiral derivatizing reagents (CDRs) were used for preparation of diastereomers of (R,S)‐mexiletine containing a primary amino group in close proximity to the stereogenic center. One anhydride, namely [(S,S)‐O,O'‐di‐p‐toluoyl tartaric acid anhydride] was synthesized and (S)‐naproxen was used as such as the chiral derivatizing reagent. The other nine CDRs were synthesized by substituting one of the fluorine atoms in 1,5‐difluoro‐2,4‐dinitrobenzene with six amino acid amides and three amino acids. The diastereomers were separated by reversed‐phase high‐performance liquid chromatography. The method was validated for linearity, accuracy, limit of detection and limit of quantification. The limit of detection was found in the range of 10–30 pmol. Copyright © 2010 John Wiley & Sons, Ltd.     

One—Pot Synthese of 3,4—Dihydropyrimidine—2（1H）—thiones Catalyzed by La（OTf）3

A general and practical procedure for the syntheses of 3,4-di-hydropyrimidine-2(1H)-thiones by a one-pot condensation of aldehyde,β-ketoester or β-diketone and thiourea using La(OTf)3 as the catalyst is described.Mild reaction conditions,excellent yields as well as the environmentally friendly character of La(OTf)3 make it an important alternative to the classic acid-catalyzed Biginelli‘s reaction.     

Design,Synthesis, and Evaluation of 3‐((4‐(t‐Butyl)‐2‐(2‐benzylidenehydrazinyl)thiazol‐5‐yl)methyl)quinolin‐2(1H)‐ones as Neuraminidase Inhibitors

A series of novel 3‐((4‐(t‐butyl)‐2‐(2‐benzylidenehydrazinyl)thiazol‐5‐yl)methyl)quinolin‐2(1H)‐ones ( 7a – 7z ) were designed, synthesized and evaluated for their ability of inhibiting neuraminidase (NA) of in?uenza H1N1 virus. Some compounds displayed moderate influenza NA inhibitory activity. Compound 7l with the scaffold of 2‐(2‐(2‐methoxybenzylidene)hydrazinyl)thiazole was the best one, exhibiting moderate NA inhibitory activity with IC₅₀ of 44.66 µmol/L. Structure‐activity relationship showed that compounds with methoxy or hydroxy groups at the ortho position, fluorine and nitro groups at the meta position and chlorine and bromine groups at the para position of phenyl ring were more active. Docking study indicated that compound 7l has important interactions with some key residues (including Asp151, Glu119, Arg292, Tyr406, and Asn347) and binds to 430‐cavity adjacent to NA active site.     

Investigation of the Interaction between N,N′‐Di(4‐Chlorophenyl)Thiourea and Human Serum Albumin by Fluorescence Spectroscopy: Synchronous Fluorescence Determination of Human Serum Albumin

Under physiological conditions, interaction between N,N′‐di(4‐chlorophenyl)thiourea synthesized and human serum albumin was investigated by using fluorescence spectroscopy and UV absorption spectrum. The intrinsic fluorescence of human serum albumin was quenched by N,N′‐di(4‐chlorophenyl)‐thiourea through a static quenching procedure. The binding constants (K) at 14 °C and 24 °C were obtained, and the values were 2.541 × 10⁵ M^?1 and 2.021 × 10⁵ M^?1, respectively. Thermodynamic parameter enthalpy change (ΔH) and entropy change (ΔS) were calculated to be ‐16.19 KJ/mol and 47.05 J·mol¹·K^?1, respectively, which indicated that hydrophobic force played a major role in interaction. The binding distance was evaluated on the basis of the theory of Föster energy transfer. The effects of various metal ions on the binding constants of N,N′‐di(4‐chlorophenyl)thiourea with human serum albumin were studied. A synchronous fluorescence technique for determination of human serum albumin was developed, and the method was successfully applied to the detection of HSA in human serum samples.     

A Cheap and Efficient Methodology for the Solvent‐Free,One‐pot and Multi‐component Synthesis of 3,4‐Dihydropyrimidin‐2(1H)‐ones Catalyzed by Mesoporous NH4H2PO4/MCM‐48 and Comparison of Its Catalytic Efficacy with NH4H2PO4/MCM‐41

The catalytic efficiency of ammonium dihydrogenphosphate was evaluated in the two heterogeneous forms of NH₄H₂PO₄/MCM‐48 and NH₄H₂PO₄/MCM‐41, as mesoporous catalysts, in the solvent free synthesis of 3,4‐dihydropyrimidin‐2(1H)‐ones through one‐pot three‐component condensation of ethyl acetoacetate, an aryl aldehyde and urea. Different reaction parameters including catalytic efficacy, solvent effect, and urea concentration are considered.     

One‐pot,Green and Efficient Synthesis of 3,4‐Dihydropyrimidin‐2(1H)‐ones or Thiones Catalyzed by Citric Acid

One‐pot three‐component condensation of ethyl acetoacetate, aldehyde and urea or thiourea in refluxing ethanol in the presence of catalytic amounts of citric acid afforded the corresponding 3,4‐dihydropyrimidin‐2(1H)‐ones/thiones in high yields. The catalyst is reusable and can be applied several times without any decrease in product yield.     

Determination and tissue distribution studies of dantrolene sodium with hydroxypropyl‐β‐cyclodextrin in rat tissue by HPLC/MS/MS

The established analytical method for determining the concentration of dantrolene sodium (Da) in rat tissues by HPLC/MS/MS technique was successfully applied to tissue distribution studies of Da in rats. Tissue homogenate samples were pretreated by protein precipitation with pre‐cooled methanol. Chromatographic separation was achieved on an Acquity HPLC column (Kromat Universil XB‐C₁₈, 2.1 × 150 mm, 3 μm). Mass spectrometry was conducted with an electrospray ionization interface in negative ionization mode and multiple reaction monitoring was used for quantitative analysis. The results showed that Da was rapidly and widely distributed in tissues and reached the maximum concentration within 0.5 h in all tissues after oral administration of Da–hydroxypropyl‐β‐cyclodextrin (DHC). It was then metabolized by liver and finally excreted from kidney,which indicated that DHC inclusion complex has better absorption and higher oral bioavailability than Da. The results also provided evidence for the safety and effectiveness of drug clinical application.     

Conformational analysis of some 1R,4S‐2‐arylidene‐p‐menthan‐3‐ones by 1H NMR spectroscopy and molecular simulation

Based on ¹H NMR spectral analysis combined with molecular simulation, conformational states of the cyclohexanone ring were studied for some 1R,4S‐2‐(4‐X‐benzylidene)‐p‐menthan‐3‐ones (X = COOCH₃ or C₆H₅) in CDCl₃ and C₆D₆. The co‐existence of chair conformers with an axial orientation of both alkyl substituents and twist‐boat forms was established for the compounds studied at room temperature (22–23° C). The substituent X does not influence appreciably the ratio of these conformers, but the fraction of twist‐boat forms increases noticeably in benzene solutions as compared with CDCl₃ solutions. Rotameric states of the isopropyl fragment were also characterised for the compounds studied. Distinctions in conformational states for the 1R,4S‐2‐arylidene‐p‐menthan‐3‐ones and (?)‐menthone were revealed and are discussed. Copyright © 2002 John Wiley & Sons, Ltd.     

NaY Zeolite Functionalized by Sulfamic Acid/Cu(OAc)2 as a Novel and Reusable Heterogeneous Hybrid Catalyst in Efficient Synthesis of Bis,Tris, and Tetrakis(indolyl)methanes, 3,4‐Dihydropyrimidin‐2(1H)‐ones,and 2‐Aryl‐1H‐benzothiazoles

An efficient acid‐catalyzed synthesis of some bis, tris, and tetrakis(indolyl)methanes, 3,4‐dihydropyrimidin‐2(1H )‐ones, and 2‐aryl‐1H ‐benzothiazoles is reported using NaY zeolite functionalized by sulfamic acid/Cu(OAc )₂ (NaY zeolite‐NHSO₃H /Cu(OAc )₂) in excellent yield. The heterogeneous catalyst has a simple work‐up procedure and could be recycled and reused for six reaction cycles.     

The structural and dynamic properties of 1‐bromodecane in urea inclusion compounds investigated by solid‐state 1H, 13C and 2H NMR spectroscopy

For asymmetric guest molecules in urea, the end‐groups of two adjacent guest molecules may arrange in three different ways: head–head, head–tail and tail–tail. Solid‐state ¹H and ¹³C NMR spectroscopy is used to study the structural properties of 1‐bromodecane in urea. It is found that the end groups of the guest molecules are randomly arranged. The dynamic characteristics of 1‐bromodecane in urea inclusion compounds are probed by variable‐temperature solid‐state ²H NMR spectroscopy (line shapes, spin–spin relaxation: T₂, spin‐lattice relaxation: T_1Z and T_1Q) between 120 K and room temperature. The comparison between the simulation and experimental data shows that the dynamic properties of the guest molecules can be described in a quantitative way using a non‐degenerate three‐site jump process in the low‐temperature phase and a degenerate three‐site jump in the high‐temperature phase, in combination with the small‐angle wobbling motion. The kinetic parameters can be derived from the simulation. Copyright © 2011 John Wiley & Sons, Ltd.