Determination of selenium and tellurium in electrolytic copper by anodic stripping voltammetry at a gold film electrode

A simple procedure for the determination of selenium and tellurium in electrolytic copper is described. These two elements are first separated from copper by passing an ammoniacal solution of the sample through Chelex-100 resin. Voltammetric interferences from nitrite liberated during the dissolution of the metal sample in nitric acid and from arsenic and antimony present in the metal are eliminated by addition of hydrogen peroxide. Excess of peroxide is quickly decomposed by the copper(II) ions present. As little as 0.01 μg Se g^-1 and 0.02 μg Te g^-1 can be determined; relative standard deviations (n = 5) are in the ranges 1.4–3.7% for selenium concentrations of 7.3–0.6 ppm in copper and 1.6—3.1% for tellurium concentrations of 4.6—0.5 ppm.     

化学蒸气发生-四通道原子荧光光谱法同时测定高纯金中的痕量As,Sb,Bi,Te

采用化学蒸气发生-四通道原子荧光光谱法测定了高纯金中的痕量砷、锑、铋和碲。用乙酸乙脂萃取分离金,水相还原后采用化学蒸气发生-四通道原子荧光光谱法测定高纯金中的痕量砷、锑、铋和碲。在最佳条件下,方法对As,Sb,Bi,Te的检出限分别为0.04,0.05,0.04,0.03 ng/mL(3σ);测定精密度分别为0.98,0.89,0.94,0.99%(对10 ng/mL As,Sb,Bi和Te混合标准,n=7)。方法对实际样品中的As,Sb,Bi,Te进行了同时测定,测定结果与标准方法无明显差异,各元素的加标回收率为95%～105%。     

The determination of tellurium in weathered outcrop,mineralized and barren rock

Sensitive and specific methods have been developed for the determination of tellurium in a wide variety of rocks and minerals. X-ray fluorescence is used for concentrations above 1 μg g^-1 and carbon furnace atomization a.a.s. for concentrations of 0.01–1μg g^-1. The tellurium is separated by precipitation as elemental tellurium after dissolution in acid; alternative dissolution procedures have been investigated.     

Determination of fluorine in geological materials by fast neutron activation based on the 19F(n,2n)18F reaction

The determination of fluorine in geological materials by fast neutron activation analysis based on the ¹⁹F(n, 2n)¹⁸F reaction is described. Fast neutrons are produced by irradiation of a thick beryllium target with 14.5 MeV deuerons. A rotating smple holder allows simultaneous irradiation of samples and standards. Fluorine-18 is separated by steam distillation of hexafluorosilicic acid or by extraction with triphenylatimony(V) dichloride and the annihilation radiation is measured with γ—γ coincidence equipment. The nuclear interference of recoil protons that induce the ¹⁸O(p,n)¹⁸F reaction is evaluated by means of synthetic samples: for a rock containing 43.4% of oxygen and 0.5% of hydrogen, the interference corresponds to 4.4 μg g^?1 fluorine. The method was applied to USGS and NIMROC reference rocks: for concentrations between 6000 and 50 μg g^?1, the relative standard deviation ranged from 2 to 10%.     

Determination of traces of rare earth elements in high-purity uranium by ion-exchange separation and neutron activation γ-spectrometry

Neutron activation γ-spectrometry is sufficiently sensitive for the determination of traces of rare earth elements but quantitative separation from uranium is essential. The rare earth elements in 0.2 M ammonium carbonate medium are quantitatively retained on Chelex-100, and are quantitatively separated from uranium by recycling the eluate. When 10-g samples are used, neutron activation provides detection limits of 1–20 μg kg^?1. Recoveries of rare earths, checked by spiking with radiotracers, are essentially complete.     

Optimization of the hyphenation between capillary zone electrophoresis and inductively coupled plasma mass spectrometry for the measurement of As-, Sb-, Se- and Te-species,applicable to soil extracts

The optimization of the hyphenation between capillary zone electrophoresis (CZE) and inductively coupled plasma mass spectrometry (ICP-MS) was studied for the simultaneous determination of metalloid species in the environment. Arsenic (arsenite, arsenate, monomethylarsonic acid, dimethylarsinic acid), selenium (selenite, selenate, selenomethionine, selenocystine), antimony (antimonate) and tellurium (tellurite, tellurate) species were simultaneously separated using a 75-μm i.d. fused silica capillary using either a chromate or a phosphate electrolyte. Different nebulizers were tested for introduction in the detector. A V-groove nebulizer (the Babington) and two concentric micronebulizers (the MCN-100 and the MicroMist) were studied in order to improve resolution, sensitivity and reproducibility. The optimization of CE-ICP-MS interface operating parameters is discussed for each nebulizer–interface combination, and special attention is given to the position of the capillary inside the nebulizer. Different nebulizer gas and liquid sheath flow rates were studied in detail and they hardly affect electrophoretic resolution and peak width. The best analytical performance characteristics were obtained with the MicroMist nebulizer. Detection limits with this nebulizer were found to range between 6 and 58 μg l⁻¹ depending on the species investigated using pressure injection and below 1 μg l⁻¹ for most of the species with electromigrative injection. Analysis of soil extracts showed that it was possible to carry out this technique on real samples.     

Evaluation of continuous hydride generation combined with helium and argon microwave induced plasmas using a surfatron for atomic emission spectrometric determination of arsenic,antimony and selenium

The direct coupling of continuous hydride generation with both Ar and He microwave induced plasmas (MIP) sustained in a surfatron has been optimized for the simultaneous determination of arsenic, antimony and selenium with atomic emission spectrometry. While a discharge tube of quartz was found suitable for the Ar plasma, the use of an Al₂O₃ tube led to improved performance of the He plasma. The He MIP was found to be less tolerant to the introduction of hydrogen than the Ar MIP, and correspondingly the hydride generation should be operated at a lower flow rate of 0.5% NaBH₄ solution. The introduction of the H₂O vapour produced during hydride generation into both discharges was found to greatly decrease the sensitivities and to degrade the measurement precision. It could be effectively removed with trapping by concentrated H₂SO₄. The detection limits (3σ) for As, Sb and Se are 1, 0.4 and 1 ng ml⁻¹ with the Ar MIP, and 2, 0.3 and 6 ng ml⁻¹ with the He MIP, respectively. The calibration curves are linear over three decades of concentration. The mutual interferences from As(III), Sb(III), Se(IV), Bi(III) and Sn(IV) were found to be negligible at interferent concentrations below 1 μg ml⁻¹ and in most cases the tolerable interferent concentrations are up to 20 μg ml⁻¹. The proposed method has been applied to the determination of As, Sb and Se in tea samples at μg g⁻¹ levels.     

Thiothenoyltrifluoroacetone as the Extracting and Colorimetric Reagent for Bismuth

Abstract

Thiothenoyltrifluoracetone (STTA) was used for the simultaneous extraction and direct spectrophotometric determination of bismuth at microgram concentration. About 98.5 μg of bismuth was extracted as the orange-red colored complex with 10 ml of 0.001 M STTA in carbontetrachloride. The extraction was quantitative at pH 6. The system conformed to Beer's Law in the concentration range of 2.5 to 30 μg/ml of bismuth at 460 nm. The method is both sensitive and selective.

The molar absorptivity was 5.6 × 10³ and sensitivity was 0.037 μg/cm². The method is selective as it is possible to accomplish extraction and colorimetrically determination of bismuth in the presence of 1:50 of several ions. Only ions such as cadmium, tin, iron, titanium and nickel interfere seriously. The overall process of extraction and determination takes hardly 30 minutes. The method is reproducible.     

Multielemental speciation of As, Se, Sb and Te by HPLC-ICP-MS

An anion exchange HPLC-ICP-MS procedure allowing the simultaneous multielemental speciation analysis of arsenic, selenium, antimony and tellurium has been developed. Four arsenic species (As^III, As^V, monomethylarsonic acid and dimethylarsinic acid), two selenium species (Se^IV and Se^VI) may be determined in a single run as well as one antimony (Sb^V) and one tellurium species (Te^VI). Alternatively Sb and/or Te may be used as internal standards for As and Se speciation studies. Optimisation of ICP-MS conditions led to satisfactory relative (0.01 (Sb^V) to 1.8 (Se^VI) ng ml⁻¹) and absolute detection limits (1–180 pg). Reproducibility ranged from 3.1 to 5.6% and the linearity was verified in the 0–200 ng ml⁻¹ range.     

Fast determination of molybdenum and tellurium by neutron activation analysis

The utilization of 14.6-min ¹⁰¹Mo and 25-min ^101gTe for the determination of molybdenum and tellurium in biological materials by radiochemical neutron activation analysis is described for the first time. Radioisotopes were separated from the samples activated in a thermal neutron flux of about l0¹⁴n cm^-2 s^-1. The radiochemical procedure for molybdenum involves extraction of Mo⁺⁺ from 6 M HCl into diethylether, re-extraction into water, precipitation as oximate, and measurement of the gamma activity of ¹⁰¹Tc. The tellurium was separated by reduction to the element with SO₂ in 3 M HCl, dissolution in HNO₃, and reprecipitation as the element for the measurement of radioactivity. The sensitivity was estimated at ca. 10 ng at the level of confidence of 95%. The methods were tested by analyzing NBS- standard Bovine Liver and Orchard Leaves for molybdenum; the concentrations found were 3.2 ± 0.1 μg g^-1 and 300 ± 60 ng g^-1, respectively. The tellurium content of bovine liver was estimated at 90 ± 15 ng g^-1.     

Determination of Tellurium by Gas Phase Molecular Absorption Spectrometry After Hydrogen Telluride Generation

Abstract

A method for determination of tellurium(IV) or tellurium(VI) is described that involves hydrogen telluride generation by reduction with sodium tetrahydro-borate(III), evolution of hydride with HCl solution, transport into a flow-cell placed in a UV-visible molecular absorption spectrophotometer and measurement of gas at 190 nm. Hydride generation and determination procedures are optimized, based on height and area of absorbance versus time profile of hydrogen telluride generated. Using the best experimental conditions found the calibration curve is linear from 5 to 100 μg/ml of tellurium, 1.1 μg/ml of tellurium(IV) or 3.1 μg/ml of tellurium(VI) can be detected, and relative standard deviation ranges from 4 to 7%. The method is applied to the analysis of additives for synthetic rubber making.     

Application of the photoionization detector for single determinations of hydride forming elements

The application of a photoionization detector in conjunction with a flow-through system is described for the determination of arsenic, antimony, selenium, tellurium, bismuth, tin, sulfide and ammonia. The analytical procedure is based upon a preliminary generation of the hydride compounds, their subsequent transfer to the gas phase and finally their detection in the photoionization detector. Linear calibration curves were obtained over three to four orders of magnitude with the following 3s-detection limits: 4 ng/ml As, 0.3 ng/ml Sb, 0.5 ng/ml Se, 3.0 ng/ml Te, 0.1 g/ml Bi, 0.5 g/ml Sn, 10.0 ng/ml S^2–, 0.5 g/ml NH₃.     

Determination of trace arsenic, antimony, selenium and tellurium in various oxidation states in water by hydride generation and atomic-absorption spectrophotometry after enrichment and separation with thiol cotton

A novel procedure for determination of trace As(III) and As(V), Sb(III) and Sb(V), Se(IV) and Se(VI), Te(IV) and Te(VI) in water by atomic-absorption spectrophotometry after separation and enrichment with "thiol cotton" and hydride generation has been established. The sorption behaviour of various oxidation states of arsenic, antimony, selenium and tellurium, and the conditions of quantitative sorption and desorption of these species were studied. The procedures for reducing species from higher oxidation states were optimized. Interferences from other species and their elimination were investigated. The selectivity of the procedure for the determination of species in higher and lower oxidation states was examined. The procedure has been successfully used to determine arsenic, antimony, selenium and tellurium in water, in the range from pg ml to ng ml . The recoveries for added spikes were in the range 90-110%, with coefficients of variation in the range 3-8%     

The formation of highly fluorescent zinc phosphate in the presence of uranium and its application to the direct fluorimetry of uranium in aqueous media

The formation and composition of highly fluorescent zinc phosphates in the presence of traces of uranium were investigated and a direct fluorimetric determination of uranium in aqueous media was developed, based on the formation of finely dispersed and stabilized fluorescent precipitates. The standard deviation for 20 μg of uranium, in 25 ml is 5% ; with the fluorimeter described, 10^-2 μg of uranium per ml can be determined with an error of 50%. The method is very selective and can be employed for analysis of uranium in ores; it is less sensitive than conventional fluorimetry of fused alkali fluorides but is much simpler and faster. Interferences can often be eliminated by suitable masking reactions.     

Simultaneous determination of arsenic, antimony, selenium and tin by gas phase molecular absorption spectrometry after two step hydride generation and preconcentration in a cold trap system

A cold trap system for the simultaneous determination of arsenic, antimony, selenium and tin by continuous hydride generation and gas phase molecular absorption spectrometry is described. The hydride generation is carried out in two steps; first, tin hydride is generated at low acidity and second, arsenic, antimony and selenium hydrides are formed at higher acidity. All the hydrides are collected in a liquid nitrogen cryogenic trap and transported to the flow cell of a diode array spectrophotometer, where molecular absorption spectra are obtained in the 190-250 nm range. Five calibration solutions containing arsenic, antimony, selenium and tin are solved using multiple linear regression analysis. Tests are performed in order to extend the same manifold to other hydrides but no signals are obtained for bismuth, cadmium, lead, tellurium and germanium. Under the optimum conditions found and using the wavelengths of maximum sensitivity (190, 198, 220 and 194 nm), the analytical characteristics of each element are calculated. The detection limits are 0.050, 0.020, 0.12 and 1.1 mug ml(-1) and the RSD values are 3.7, 3.1, 3.5 and 3.0% for As, Sb, Se and Sn, respectively. The method is applied to As, Sb, Se and Sn determination in natural spiked water samples.     

Electroanalytical Determination of Cadmium(II) and Lead(II) Using an Antimony Nanoparticle Modified Boron‐Doped Diamond Electrode

We report the simultaneous electroanalytical determination of Pb²⁺ and Cd²⁺ by linear sweep anodic stripping voltammetry (LSASV) using an antimony nanoparticle modified boron doped diamond (Sb‐BDD) electrode. Sb deposition was performed in situ with the analytes, from a solution of 1 mg L^?1 SbCl₃ in 0.1 M HCl (pH 1). Pb²⁺ inhibited the detection of Cd²⁺ during simultaneous additions at the bare BDD electrode, whereas in the presence of antimony, both peaks were readily discernable and quantifiable over the linear range 50–500 μg L^?1.     

Determination of bismuth,lead and tellurium in copper by atomic absorption spectrometry with introduction of solid samples into an induction furnace

Atomic absorption spectrometry with an induction furnace is used for the determination of bismuth (0.015–10 μg g^-1), lead (0.2–15 μg g^-1) and tellurium (0.04–5 μg g^-1) in 2–30-mg samples of copper and low-alloy copper dropped into the furnace. Calibration graphs of peak area versus mass of element were constructed by use of standardised alloys. The accuracy, precision and limits of detection of the method are described for numerous copper samples. With alloys containing more than 0.1 μg Bi g^-1, 0.2 μg Pb g^-1 and 0.8 μg Te g^-1, average relative standard deviations are 7%, 6% and 8%, respectively. The limits of detection for bismuth, lead and tellurium are 0.01, 0.1 and 0.02 μg g^-1, respectively.     

Flameless atomic absorption spectrometry of antimony

Flameless atomic absorption spectrometry of antimony has been investigated with a carbon rod device. Antimony may be determined in solution at a level of 10^-10 g with a sample volume of 0.5 μl. Optimal conditions and interferences are described. Matrix effects on antimony necessitated a preliminary solvent extraction of the chloride complex from hydrochloric acid solution containing nitrite with methyl isobutyl ketone. The determination of antimony in metallurgical samples was shown to be satisfactory.     

Multielement analysis of uraniferous rocks by INAA: Special reference to interferences due to uranium and fission of uranium

The presence of uranium in a sample enhances the true values of La, Ce, Nd, Sm determined by INAA if appropriate corrections are not made for the interference. The enhancement of the true values comes about because the (n, γ) activation products of these elements, viz.¹⁴⁰La,¹⁴¹Ce,¹⁴⁷Nd,¹⁵³Sm, are also produced from the fission of²³⁵U (～0.72% natural isotopic abundance) even when La, Ce, Nd, Sm are totally absent in the given sample. In a 5 hour irradiation 1 μg of U is found to be equal to 0.28 μg of Ce and 0.23 μg of Nd while the equivalent La is found to be dependent upon the delay from end of irradiation to sample counting time. A numerical procedure is given to correct for these interferences. Spectral interferences from fission and (n, γ) β products of uranium in the determination of other trace elements by INAA is also investigated. Uranium is found to be determined best using the 278 keV gamma-ray of²³⁹Np.     

Extraction,Spectrophotometric, and Atomic Absorption Spectrophotometric Determination of Selenium With N-Phenylbenzohydroxamic Acid

Abstract

Solvent extraction spectrophotometric and atomic absorption spectrophotometric methods for the determination of selenium(IV) in microgram quantities are described. The selenium(IV) forms yellow colored complex with N-phenylbenzohydroxamic acid (PBHA) extractable into chloroform from 7 M HClO₄. Se-PBHA complex has maximum absorbance at 345 nm with a molar absorptivity 1.5 × 10⁵ 1 mol^?1 cm^?1 and Sandell's sensitivity 0.000526 μg /cm². Effect of molarity, reagent concentration, diverse ions on the extraction of selenium complex were studied. The selenium is determined in presence of tellurium.