New Bithiazole‐Based Sensitizers for Efficient and Stable Dye‐Sensitized Solar Cells

A series of new push–pull organic dyes ( BT‐I – VI ), incorporating electron‐withdrawing bithiazole with a thiophene, furan, benzene, or cyano moiety, as π spacer have been synthesized, characterized, and used as the sensitizers for dye‐sensitized solar cells (DSSCs). In comparison with the model compound T1 , these dyes containing a thiophene moiety between triphenylamine and bithiazole display enhanced spectral responses in the red portion of the solar spectrum. Electrochemical measurement data indicate that the HOMO and LUMO energy levels can be tuned by introducing different π spacers between the bithiazole moiety and cyanoacrylic acid acceptor. The incorporation of bithiazole substituted with two hexyl groups is highly beneficial to prevent close π–π aggregation, thus favorably suppressing charge recombination and intermolecular interaction. The overall conversion efficiencies of DSSCs based on bithiazole dyes are in the range of 3.58 to 7.51 %, in which BT‐I ‐based DSSCs showed the best photovoltaic performance: a maximum monochromatic incident photon‐to‐current conversion efficiency (IPCE) of 81.1 %, a short‐circuit photocurrent density (J_sc) of 15.69 mA cm^?2, an open‐circuit photovoltage (V_oc) of 778 mV, and a fill factor (ff) of 0.61, which correspond to an overall conversion efficiency of 7.51 % under standard global AM 1.5 solar light conditions. Most importantly, long‐term stability of the BT‐I – III ‐based DSSCs with ionic‐liquid electrolytes under 1000 h of light soaking was demonstrated and BT‐II with a furan moiety exhibited better photovoltaic performance of up to 5.75 % power conversion efficiency.     

Constructing Organic D–A–π‐A‐Featured Sensitizers with a Quinoxaline Unit for High‐Efficiency Solar Cells: The Effect of an Auxiliary Acceptor on the Absorption and the Energy Level Alignment

Four organic D–A –π‐A‐featured sensitizers (TQ1, TQ2, IQ1, and IQ2) have been studied for high‐efficiency dye‐sensitized solar cells (DSSCs). We employed an indoline or a triphenylamine unit as the donor, cyanoacetic acid as the acceptor/anchor, and a thiophene moiety as the conjugation bridge. Additionally, an electron‐withdrawing quinoxaline unit was incorporated between the donor and the π‐conjugation unit. These sensitizers show an additional absorption band covering the broad visible range in solution. The contribution from the incorporated quinoxaline was investigated theoretically by using DFT and time‐dependent DFT. The incorporated low‐band‐gap quinoxaline unit as an auxiliary acceptor has several merits, such as decreasing the band gap, optimizing the energy levels, and realizing a facile structural modification on several positions in the quinoxaline unit. As demonstrated, the observed additional absorption band is favorable to the photon‐to‐electron conversion because it corresponds to the efficient electron transitions to the LUMO orbital. Electrochemical impedance spectroscopy (EIS) Bode plots reveal that the replacement of a methoxy group with an octyloxy group can increase the injection electron lifetime by a factor of 2.4. IQ2 and TQ2 can perform well without any co‐adsorbent, successfully suppress the charge recombination from TiO₂ conduction band to I₃^? in the electrolyte, and enhance the electron lifetime, resulting in a decreased dark current and enhanced open circuit voltage (V_oc) values. By using a liquid electrolyte, DSSCs based on dye IQ2 exhibited a broad incident photon‐to‐current conversion efficiency (IPCE) action spectrum and high efficiency (η=8.50 %) with a short circuit current density (J_sc) of 15.65 mA cm^?2, a V_oc value of 776 mV, a fill factor (FF) of 0.70 under AM 1.5 illumination (100 mW cm^?2). Moreover, the overall efficiency remained at 97 % of the initial value after 1000 h of visible‐light soaking.     

Two main chain polymeric metal complexes as dye sensitizers for dye‐sensitized solar cells based on the coordination of the ligand containing 8‐hydroxyquinoline and phenylethyl or fluorene units with Eu(III)

Two novel main chain polymeric metal complexes containing 8‐hydroxyquinoline europium complexes and phenylethyl or fluorene units: 1,4‐Dioctyloxy‐2,5‐bis[2‐(8‐hydroxyquinoline)‐vinyl]‐benzene Eu(III) (3) and 2,7‐bis[2‐(8‐hydroxyquinoline)‐vinyl]‐9,9′‐diocthylfluorene Eu(III) (4) with donor–acceptor‐π‐conjugated structure (D‐π‐A) have been synthesized and investigated as dye sensitizers for dye‐sensitized solar cells dyes (DSSCs). They have been determined and studied by FT‐IR, TGA, DSC, GPC, Elemental analysis, UV–vis absorption spectroscopy, photoluminescence spectroscopy, cyclic voltammetry, and application in dye‐sensitized solar cells (DSSCs) as dye sensitizers. On the basis of optimized dye and molecular structure, they have shown solar‐to‐electricity conversion efficiency 2.25% for 3 (J_sc = 4.77 mA cm^?2, V_oc = 630 mV, FF = 0.75) and 3.04% for 4 (J_sc = 6.33 mA cm^?2, V_oc = 640 mV, FF = 0.75), under the illumination of AM1.5G, 100 mW/cm². The IPCE of 3 and 4 are 30% and 46% at 400 nm, respectively. Besides, they showed good stabilities with thermal decomposition temperatures at 280 °C and 225 °C, respectively, which are suitable for DSSCs. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 1943–1951, 2010     

Benzimidazole‐indole‐chalcone connected methacrylate‐based side chain D‐π‐A polymer and its application in organic photovoltaics

Herein, we report four metal‐free organic polymethacrylates (In‐In‐BzI)PMA , (Ac‐In‐BzI)PMA , (TPA‐In‐BzI)PMA , and (Py‐In‐BzI)PMA with pendant chromophores donor‐π‐conjugated‐acceptor (D‐π‐A) molecular framework as photosensitizers for dye‐sensitized solar cells (DSSCs). In which the donor‐acceptor units are attached by an indole‐chalcone extending side chain to inhibit back electron transfer and charge recombination; the π‐linker component contains varied chalcone‐based substituents to enhance the sunlight‐harvesting ability of the solar device. Photon‐current cells based on the DSSC format were fabricated using the polymers as sensitizers. The DSSC device assembled using (TPA‐In‐BzI)PMA exhibits a considerably better IPCE peak and J–V response, with an overall power conversion efficiency of 3.70% under the illumination of AM 1.5G (100 mW cm^–2). © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55, 997–1007     

Tetraaryl ZnII Porphyrinates Substituted at β‐Pyrrolic Positions as Sensitizers in Dye‐Sensitized Solar Cells: A Comparison with meso‐Disubstituted Push–Pull ZnII Porphyrinates

A facile and fast approach, based on microwave‐enhanced Sonogashira coupling, has been employed to obtain in good yields both mono‐ and, for the first time, disubstituted push–pull Zn^II porphyrinates bearing a variety of ethynylphenyl moieties at the β‐pyrrolic position(s). Furthermore, a comparative experimental, electrochemical, and theoretical investigation has been carried out on these β‐mono‐ or disubstituted Zn^II porphyrinates and meso‐disubstituted push–pull Zn^II porphyrinates. We have obtained evidence that, although the HOMO–LUMO energy gap of the meso‐substituted push–pull dyes is lower, so that charge transfer along the push–pull system therein is easier, the β‐mono‐ or disubstituted push–pull porphyrinic dyes show comparable or better efficiencies when acting as sensitizers in DSSCs. This behavior is apparently not attributable to more intense B and Q bands, but rather to more facile charge injection. This is suggested by the DFT electron distribution in a model of a β‐monosubstituted porphyrinic dye interacting with a TiO₂ surface and by the positive effect of the β substitution on the incident photon‐to‐current conversion efficiency (IPCE) spectra, which show a significant intensity over a broad wavelength range (350–650 nm). In contrast, meso‐substitution produces IPCE spectra with two less intense and well‐separated peaks. The positive effect exerted by a cyanoacrylic acid group attached to the ethynylphenyl substituent has been analyzed by a photophysical and theoretical approach. This provided supporting evidence of a contribution from charge‐transfer transitions to both the B and Q bands, thus producing, through conjugation, excited electrons close to the carboxylic anchoring group. Finally, the straightforward and effective synthetic procedures developed, as well as the efficiencies observed by photoelectrochemical measurements, make the described β‐monosubstituted Zn^II porphyrinates extremely promising sensitizers for use in DSSCs.     

First‐Generation Subporphyrinatoboron(III) Sensitizers Surpass the 10 % Power Conversion Efficiency Threshold

Subporphyrinatoboron(III) (SubB) sensitizers were synthesized for use in dye‐sensitized solar cells (DSSCs). The prototype, which comprises a sterically demanding 3,5‐di‐tert‐butylphenyl scaffold, a meso‐ethynylphenyl spacer, and a cyanoacrylic acid anchoring group, achieved an open‐circuit voltage V_OC of 836 mV, short‐circuit current density J_SC of 15.3 mA cm^?2, fill factor of 0.786, and a photon‐to‐current conversion efficiency of 10.1 %. Such astonishing figures suggest that a bright future lies ahead for SubB in the realm of DSSCs.     

Benzotriazole-Bridged Sensitizers Containing a Furan Moiety for Dye-Sensitized Solar Cells with High Open-Circuit Voltage Performance

Two new benzotriazole-bridged sensitizers are designed and synthesized ( BTA-I and BTA-II ) containing a furan moiety for dye-sensitized solar cells (DSSCs). Two corresponding dyes ( BTA-III and BTA-IV ) with a thiophene spacer were also synthesized for comparison. All of these dyes performed as sensitizers for DSSCs, and the photovoltaic performance data of these benzotriazole-bridged dyes showed a high open-circuit voltage (V_oc: 804–834 mV). Among the four dyes, DSSCs based on BTA-II , with a furan moiety and branched alkyl chain, showed the highest V_oc (834 mV), a photocurrent density (J_sc) of 12.64 mA cm⁻², and a fill factor (FF) of 0.64, corresponding to an overall conversion efficiency (η) of 6.72 %. Most importantly, long-term stability of the BTA-I , BTA-II , BTA-III , BTA-IV -based DSSCs with ionic-liquid electrolytes under 1000 h light-soaking was demonstrated, and BTA-II exhibited better photovoltaic performance of up to 5.06 % power conversion efficiency.     

Restricted Rotation of σ‐Bonds through a Rigidified Donor Structure to Increase the ICT Ability of Platinum‐Acetylide‐Based DSSCs

A series of new triarylamine‐based platinum‐acetylide complexes ( WY s) have been designed and synthesized as new sensitizers for applications in dye‐sensitized solar cells (DSSCs). With the aim of investigating the effect of a rigidifying donor structure on the photoelectrical parameters of the corresponding DSSCs, two new sensitizers, WY1 and WY2 , with rigid and coplanar fluorene units as an electron donor, were prepared. Moreover, two sensitizers that contained triphenylamine units as an electron donor, WY3 and WY4 , were also synthesized for comparison. The photo‐ and electrochemical properties of all of these new complexes have been extensively explored. We found that the dimethyl‐fluorene unit exhibited a stronger electron‐donating ability and better photovoltaic performance compared to the triphenylamine unit, owing to its rigidifying structure, which restricted the rotation of σ bonds, thus increasing the conjugation efficiency. Furthermore, WY2 , which contained a dimethyl‐fluorene unit as an electron donor and bithiophene as a π bridge, showed a relatively high open‐circuit voltage (V_oc) of 640 mV and a PCE of 4.09 %. This work has not only expanded the choice of platinum‐acetylide sensitizers, but also demonstrates the advantages of restricted rotation of donor σ bonds for improved behavior of the corresponding DSSCs.     

Molecular Design of D‐π‐A Type II Organic Sensitizers for Dye Sensitized Solar Cells

Four new type II organic dyes with D‐π‐A structure (donor‐π‐conjugated‐acceptor) and two typical type II sensitizers based on catechol as reference dyes are synthesized and applied in dye sensitized solar cells (DSCs). The four dyes can be adsorbed on TiO₂ through hydroxyl group directly. Electron injection can occur not only through the anchoring group (hydroxyl group) but also through the electron‐withdrawing group (? CN) located close to the semiconductor surface. Experimental results show that the type II sensitizers with a D‐π‐A system obviously outperform the typical type II sensitizers providing much higher conversion efficiency due to the strong electronic push‐pull effect. Among these dyes, LS223 gives the best solar energy conversion efficiency of 3.6%, with J_sc=7.3 mA·cm^?2, V_oc=0.69 V, FF=0.71, the maximum IPCE value reaches 74.9%.     

Efficient Solar Cells Sensitized by Porphyrins with an Extended Conjugation Framework and a Carbazole Donor: From Molecular Design to Cosensitization

Porphyrin dyes containing the carbazole electron donor have been designed and optimized by wrapping the porphyrin framework, introducing an additional ethynylene bridge to extend the wavelength range of light absorption, and further suppression of the dye aggregation by introducing additional alkoxy chains. Application of a cosensitization approach results in improved current density (J_sc) and open‐circuit voltage (V_oc) values, thus achieving the highest cell efficiency of 10.45 %. This work provides an effective combined strategy of molecular design and cosensitization for developing efficient dye‐sensitized solar cells (DSSCs). In addition, carbazole has been demonstrated to be a promising donor for porphyrin sensitizers.     

Enhanced Performance of Quasi‐Solid‐State Dye‐Sensitized Solar Cells by Branching the Linear Substituent in Sensitizers Based on Thieno[3,4‐c]pyrrole‐4,6‐dione

Thieno[3,4‐c]pyrrole‐4,6‐dione‐based organic sensitizers with triphenylamine ( FNE38 and FNE40 ) or julolidine ( FNE39 and FNE41 ) as electron‐donating unit have been designed and synthesized. A linear hexyl group or a branched alkyl chain, the 2‐ethylhexyl group, is incorporated into molecular skeleton of the dyes to minimize intermolecular interactions. The absorption, electrochemical, and photovoltaic properties for these sensitizers were then systematically investigated. It is found that the sensitizers have similar photophysical and electrochemical properties, such as absorption spectra and energy levels, owing to their close chemical structures. However, the quasi‐solid‐state dye‐sensitized solar cells (DSSCs) based on the two types of sensitizers exhibit very different performance parameters. Upon the incorporation of the short ethyl group on the hexyl moiety, enhancements in both open‐circuit voltage (V_oc) and short‐circuit current (J_sc) are achieved for the quasi‐solid‐state DSSCs. The V_oc gains originating from the suppression of charge recombination were quantitatively investigated and are in good agreement with the experimentally observed V_oc enhancements. Therefore, an enhanced solar energy conversion efficiency (η) of 6.16 %, constituting an increase by 23 %, is achieved under standard AM 1.5 sunlight without the use of coadsorbant agents for the quasi‐solid‐state DSSC based on sensitizer FNE40 , which bears the branched alkyl group, in comparison with that based on FNE38 carrying the linear alkyl group. This work presents a design concept for considering the crucial importance of the branched alkyl substituent in novel metal‐free organic sensitizers.     

New Dual Donor–Acceptor (2D‐π‐2A) Porphyrin Sensitizers for Stable and Cost‐Effective Dye‐Sensitized Solar Cells

A series of porphyrin sensitizers that featured two electron‐donating groups and dual anchoring groups that were connected through a porphine π‐bridging unit have been synthesized and successfully applied in dye‐sensitized solar cells (DSSCs). The presence of electron‐donating groups had a significant influence on their spectroscopic, electrochemical, and photovoltaic properties. Overall, the dual anchoring groups gave tunable electronic properties and stronger attachment to TiO₂. These new dyes were readily synthesized in a minimum number of steps in gram‐scale quantities. Optical and electrochemical data confirmed the advantages of these dyes for use as sensitizers in DSSCs. Porphyrins with electron‐donating amino moieties provided improved charge separation and better charge‐injection efficiencies for the studied dual‐push–pull dyes. Attenuated total reflectance–Fourier‐transform infrared (ATR‐FTIR) and X‐ray photoelectron spectroscopy of the porphyrin dyes on TiO₂ suggest that both p‐carboxyphenyl groups are attached onto TiO₂, thereby resulting in strong attachment. Among these dyes, cis-Zn2BC2A , with two electron‐donating 3,6‐ditertbutyl‐phenyl‐carbazole groups and dual‐anchoring p‐carboxyphenyl groups, showed the highest efficiency of 4.07 %, with J_SC=9.81 mA cm^?2, V_OC=0.63 V, and FF=66 %. Our results also indicated a better photostability of the studied dual‐anchored sensitizers compared to their mono‐anchored analogues under identical conditions. These results provide insight into the developments of a new generation of high‐efficiency and thermally stable porphyrin sensitizers.     

High Molar Extinction Coefficient Organic Sensitizers for Efficient Dye‐Sensitized Solar Cells

We have designed and synthesized highly efficient organic sensitizers with a planar thienothiophene–vinylene–thienothiophene linker. Under standard global AM 1.5 solar conditions, the JK‐113 ‐sensitized cell gave a short circuit photocurrent density (J_sc) of 17.61 mA cm^?2, an open‐circuit voltage (V_oc) of 0.71 V, and a fill factor (FF) of 72 %, corresponding to an overall conversion efficiency (η) of 9.1 %. The incident monochromatic photo‐to‐current conversion efficiency (IPCE) of JK‐113 exceeds 80 % over the spectral region from 400 to 640 nm, reaching its maximum of 93 % at 475 nm. The band tails off toward 770 nm, contributing to the broad spectral light harvesting. Solar‐cell devices based on the sensitizer JK‐113 in conjunction with a volatile electrolyte and a solvent‐free ionic liquid electrolyte gave high conversion efficiencies of 9.1 % and 7.9 %, respectively. The JK‐113 ‐based solar cell fabricated using a solvent‐free ionic liquid electrolyte showed excellent stability under light soaking at 60 °C for 1000 h.     

From salmon pink to blue natural sensitizers for solar cells: Canna indica L., Salvia splendens, cowberry and Solanum nigrum L.

Study on dye-sensitized solar cells (DSSCs) with extracts of Canna indica L., Salvia splendens, Solanum nigrum L. as sensitizers is firstly reported in this paper. DSSCs were assembled by using natural dyes extracted from C. indica L., S. splendens, cowberry and S. nigrum L. as sensitizers. The energy conversion efficiency of the cells sensitized with dyes of C. indica L., S. splendens, cowberry and S. nigrum L. was 0.29%, 0.26%, 0.13% and 0.31%, respectively. A novel technique was taken to fabricate TiO₂ electrode films by electrophoresis. We present FTIR and UV–vis spectroscopy studies of structures and light absorption of these four kinds of natural dyes. The electrochemical impedance spectroscopy (EIS) was used to analyze the interface resistance of cells. The result indicated that high resistance existed in the interfaces of cell with cowberry extract as sensitizer.     

Ethoxy‐substituted Oligo‐phenylenevinylene‐Bridged Organic Dyes for Efficient Dye‐Sensitized Solar Cells

Organic dyes with ethoxy‐substituted oligo‐phenylenevinylene as chromophores were synthesized for dye‐sensitized solar cells (DSSCs), and the detailed relationships between the dye structures, photophysical properties, electrochemical properties, and performances of DSSCs were described. The dye S3O showed broad IPCE spectra in the spectral range of 350–750 nm, and the dye S1P showed solar energy‐to‐electricity conversion efficiency (() of up to 4.23% under AM 1.5 irradiation (100 mW/cm²) in comparison with the reference Ru‐complex (N719 dye) with an η value of 5.90% under similar experimental conditions.     

Ruthenium and Osmium Complexes That Bear Functional Azolate Chelates for Dye‐Sensitized Solar Cells

The preparation of sensitizers for dye‐sensitized solar cells (DSSCs) represents an active area of research for both sustainability and renewable energy. Both Ru^II and Os^II metal sensitizers offer unique photophysical and electrochemical properties that arise from the intrinsic electronic properties, that is, the higher propensity to form the lower‐energy metal‐to‐ligand charge‐transfer (MLCT) transition, and their capability to support chelates with multiple carboxy groups, which serve as a bridge to the metal oxide and enable efficient injection of the photoelectron. Here we present an overview of the synthesis and testing of these metal sensitizers that bear functional azolate chelates (both pyrazolate and triazolate), which are capable of modifying the metal sensitizers in a systematic and beneficial manner. Basic principles of the molecular designs, the structural relationship to the photophysical and electrochemical properties, and performances of the as‐fabricated DSSCs are highlighted. The success in the breakthrough of the synthetic protocols and potential applications might provide strong stimulus for the future development of technologies such as DSSCs, organic light‐emitting diodes, solar water splitting, and so forth.     

Enhancement of photocurrent of polymer‐gelled dye‐sensitized solar cell by incorporation of exfoliated montmorillonite nanoplatelets

Poly(n‐isopropylacrylamide) (PNIPAAm) and its nanocomposite with exfoliated montmorillonite (MMT) were prepared by soap‐free emulsion polymerization and individually applied to gel the electrolyte systems for the dye‐sensitized solar cells (DSSCs). Each exfoliated MMT nanoplatelet had a thickness of ～ 1 nm, carried ～ 1.8 cation/nm², and acted like a two‐dimensional electrolyte. The DSSC with the LiI/I₂/tertiary butylpyridine electrolyte system gelled by this polymer nanocomposite had higher short‐circuit current density (J_sc) compared to that gelled by the neat PNIPAAm. The former has a J_sc of 12.6 mA/cm², an open circuit voltage (V_oc) of 0.73 V, and a fill factor (FF) of 0.59, which harvested 5.4% electricity conversion efficiency (η) under AM 1.5 irradiation at 100 mW/cm², whereas the latter has J_sc = 7.28 mA/cm², V_oc = 0.72 V, FF = 0.60, and η = 3.17%. IPCE of the nanocomposite‐gelled DSSC were also improved. Electrochemical impedance spectroscopy of the DSSCs revealed that the nanocomposite‐gelled electrolytes significantly decreased the impedances in three major electric current paths of DSSCs, that is, the resistance of electrolytes and electric contacts, impedance across the electrolytes/dye‐coated TiO₂ interface, and Nernstian diffusion within the electrolytes. The results were also consistent with the increased molar conductivity of nanocomposite‐gelled electrolytes. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 47–53, 2008     

Functionalized Alkynylplatinum(II) Polypyridyl Complexes for Use as Sensitizers in Dye‐Sensitized Solar Cells

A series of platinum(II) alkynyl‐based sensitizers has been synthesized and found to show light‐to‐electricity conversion properties. These dyes were developed as sensitizers for the application in nanocrystalline TiO₂ dye‐sensitized solar cells (DSSCs). Their photophysical and electrochemical properties were studied. The excited‐state property was probed using nanosecond transient absorption spectroscopy, which showed the formation of a charge‐separated state that arises from the intramolecular photoinduced charge transfer from the platinum(II) alkynylbithienylbenzothiadiazole moiety (donor) to the polypyridyl ligand (acceptor). A lifetime of 3.4 μs was observed for the charge‐separated state. A dye‐sensitized solar cell based on one of the complexes showed a short‐circuit photocurrent of 7.12 mA cm^?2, an open circuit voltage of 780 mV, and a fill factor of 0.65, thus giving an overall power conversion efficiency of 3.6 %.     

Photophysical and Electrochemical Properties,and Molecular Structures of Organic Dyes for Dye‐Sensitized Solar Cells

Dye‐sensitized solar cells (DSSCs) based on organic dyes adsorbed on oxide semiconductor electrodes, such as TiO₂, ZnO, or NiO, which have emerged as a new generation of sustainable photovoltaic devices, have attracted much attention from chemists, physicists, and engineers because of enormous scientific interest in not only their construction and operational principles, but also in their high incident‐solar‐light‐to‐electricity conversion efficiency and low cost of production. To develop high‐performance DSSCs, it is important to create efficient organic dye sensitizers, which should be optimized for the photophysical and electrochemical properties of the dyes themselves, with molecular structures that provide good light‐harvesting features, good electron communication between the dye and semiconductor electrode and between the dye and electrolyte, and to control the molecular orientation and arrangement of the dyes on a semiconductor surface. The aim of this Review is not to make a list of a number of organic dye sensitizers developed so far, but to provide a new direction in the epoch‐making molecular design of organic dyes for high photovoltaic performance and long‐term stability of DSSCs, based on the accumulated knowledge of their photophysical and electrochemical properties, and molecular structures of the organic dye sensitizers developed so far.     

Novel Thiazolo[5,4‐d]thiazole‐Based Organic Dyes for Quasi‐Solid‐State Dye‐Sensitized Solar Cells

A series of novel metal‐free organic dyes containing the thiazolo[5,4‐d]thiazole moiety were designed and synthesized for quasi‐solid‐state dye‐sensitized solar cells (DSSCs). Different alkoxy chains were introduced into the electron donor part of the dye molecules for comparison. The optical, electrochemical, and photovoltaic properties for all sensitizers were systematically investigated. It was found that the sensitizers with the different alkoxy groups have similar photophysical and electrochemical properties, such as absorbance and energy levels, owing to their close chemical structures. However, the quasi‐solid‐state DSSCs based on the resulting sensitizers exhibit different performance parameters. The quasi‐solid‐state DSSC based on sensitizer FNE74 with two octyloxy chains possessed the highest solar energy conversion efficiency of 5.10 % under standard AM 1.5G sunlight illumination without the use of coadsorbant agents.