Electrochemical solid-phase microextraction of anions and cations using polypyrrole coatings and an integrated three-electrode device

A method for the extraction, transfer and desorption of anions and cations under controlled potential conditions employing a new integrated three-electrode device is described. The device, containing working, reference and counter electrodes, was prepared from tubes that could be moved vertically with respect to each other. In this way, a small amount of solvent, held by capillary force, remained between the electrodes when the device was lifted out of a solution after an extraction. This design allowed the potential control to be maintained at all times. With the new integrated device, it was possible to perform potential controlled desorption into vials containing as little as 200 microl of solution. The required ion exchange capacity was obtained by electrodeposition of a polypyrrole coating on the surface of the glassy carbon working electrode. Solid-phase microextractions of several cations or anions were performed simultaneously under potentiostatic control by doping the polypyrrole coating with different anions such as perchlorate and p-toluenesulfonate. The efficiency of the extractions, which could be altered by varying the potential of the working electrode, could be increased by 150 to 200% compared to extractions using normal solid-phase microextraction conditions under open circuit conditions. A constant potential of +1.0 V and -0.5 V with respect to the silver pseudo reference electrode, was found to be well-suited for the extraction of samples containing ppm concentrations of anions (chloride, nitrite, bromide, nitrate, sulfate and phosphate) and cations (cadmium, cobalt and zinc), respectively.     

Lower limits of the potentiometric microtitration of chloride with silver ions

The lower levels of the potentiometric titration of chloride with silver ions were investigated. The titrant was 0.001 N acetonic silver perchlorate. The titration media were acetone and acetic anhydride:acetone (4:1). A silver sulfide ion-selective indicator electrode and a double-junction reference electrode were use to monitor emf's. This titration is limited only by the trace amounts of chloride in the reagents used. Satisfactory results and well-defined titration curves were obtained down to 7 μg of chloride per 50 ml of solution (0.2 μmol; 4 × 10^?6N).A small polarization current can be used to enhance the potentiometric breaks of this titration. In an 80% methanolic medium with 0.001 N aqueous silver nitrate and a polarization current of ?0.4 μA, the lower practical limit of this titration was near 22.3 μg of chloride (1.26 × 10^?5N).     

Extraction of metals by neutral sulfur-containing extractants: Part I. o-isopropyl-n-ethylthiocarbamate

The formation of neutral mixed complexes of the MX_mS_p type (where M is a metal ion with m⁺ charge, X the inorganic anion, and S the sulfur-containing extractant) allows a selective extraction of various elements. The extraction of many metals from mineral acid solutions or from halide-sulfuric acid mixtures by 0.05 M O-isopropyl-N-ethylthiocarbamate(IPETC) solution in chloroform has been studied. (IPETC) possesses very high selectivity for silver and mercury ions in extractions from HNO₃, H_{2)SO4, HClO4 and HCl solutions. In addition to silver and mercury, Cu, Au, Tl and Se are readily extracted from solutions containing bromide. From iodide solutions, copper, gold and thallium ions may be selectively extracted because silver and mercury cannot be extracted at concentrations of iodide above 0.1 M.(IPETC} extracts metals as mixed complexes, containing the halide and apparently the extractant in the molecular form.     

Ultrasound-assisted extraction in the determination of arsenic,cadmium, copper,lead, and silver in contaminated soil samples by inductively coupled plasma atomic emission spectrometry

An extraction method was developed for the determination of toxic elements in contaminated soil samples by inductively coupled plasma atomic emission spectrometry (ICP-AES). The determination of arsenic, cadmium, lead, and silver in ultrasound-assisted extracts of SRM 2710 and SRM 2711 by ICP-AES was carried out with high accuracy and precision (RSD<3.7%). The certified concentrations of the SRMs were obtained for arsenic, cadmium, lead, and silver by using an ultrasound-assisted extraction method with a digestion solution of (1+1)-diluted aqua regia. The determination of copper in SRMs by the ultrasound-assisted extraction method and analysis by ICP-AES failed to obtain the certified concentrations at the 95% level of confidence using (+/-2 s) as confidence limits of the mean. However, the same results were observed with the use of the microwave digestion method and reflux, which is the ISO 11466 standard method. The analysis of the SRMs showed that the ultrasound-assisted extraction method is highly comparable with the other methods used for such purposes. The major advantages of the ultrasound-assisted extraction method compared to the microwave and reflux methods are the high treatment rate (50 samples simultaneously in nine minutes) and low reagent usage, the main benefit of which are the low chloride and nitrate concentrations in the extracts.     

Detection of Quaternary Ammonium Drugs in Equine Urine by Liquid Chromatography-Mass Spectrometry

Quaternary ammonium drugs are anticholinergic agents and some of which have been known to be abused in equine sports. A general screening method for this class of drugs in equine urine by liquid chromatography-mass spectrometry (LC-MS) has not been reported. The paper describes an efficient LC-MS-MS method for the simultaneous detection and confirmation of twenty quaternary ammonium drugs at low ng mL^?1 in equine urine after solid-phase extraction. Quaternary ammonium drugs were extracted from equine urine by solid-phase extraction using ISOLUTE^® CBA SPE Columns and analysed by LC-MS-MS in the positive electrospray ionisation mode. Separation of twenty quaternary ammonium drugs (the quaternary ammonium ions of edrophonium chloride, pyridostigmine bromide, neostigmine bromide, bretylium tosylate, ipratropium bromide, tubocurarine chloride, N-butylscopolammonium bromide, mepenzolate bromide, rocuronium bromide, clidinium bromide, pipenzolate bromide, isopropamide iodide, glycopyrronium bromide, alcuronium chloride, oxyphenonium bromide, propantheline bromide, tridihexethyl chloride, vecuronium bromide, mivacurium chloride and pancuronium bromide) was achieved in a reversed phase column with a mixture of aqueous ammonium formate (pH 3.0, 10 mM) and acetonitrile as the mobile phase. Detection and confirmation of the twenty quaternary ammonium drugs at about 5 ng mL^?1 in equine urine could be achieved within 22 min using product-ion scan MS-MS. The target analytes were detected by examination of extracted-ion chromatograms of their product ions. Drugs spiked in different equine urine (n = 15) were consistently detected. Negative samples (n = 30) of normal post-race equine urine have also been analysed, no matrix interference at the targeted masses and retention times was observed. The method was successfully applied to the analyses of drug-administration samples. Other method validation data including reproducibility and recovery will also be presented. An LC-MS-MS method for the simultaneous detection and confirmation of twenty quaternary ammonium drugs in equine urine was developed. The methodology should be applicable to other biological matrices such as human urine.     

Molecular mechanism of the photochemical generation of gold nanoparticles in ethylene glycol: support for the disproportionation mechanism

It is found that replacement of the chloride ions in tetrachloroauric acid with bulky bromide ions inhibits the formation of gold nanoparticles in the photochemical reduction in ethylene glycol. However, the addition of silver ions to either the bromide or the chloride auric acid solution is found to enhance the rate of gold nanoparticle formation. These results are found to be accounted for by the previously proposed mechanism (Eustis, S.; Hsu, H.-Y.; El-Sayed, M. A. J. Phys. Chem. B 2005, 109, 4811) which involves disproportionation of the chloroauric complexes to generate free gold atoms and chloride ions. The steric effects of the bulky bromide ions inhibit the formation of the Au-Au bond needed in the electron transfer process of the disproportionation reaction. The addition of Ag+ ions results in the formation of insoluble silver halide, which shifts the disproportionation reaction toward the formation of gold atoms and thus the formation of gold nanoparticles.     

Some observations on an indirect atomic absorption spectrophotometric method for the microdetermination of chlorine or bromine in organic compounds

An atomic absorption spectrophotometric method for the microdetermination of chlorine or bromine in organic compounds is described; it is based on oxygen flask combustion to yield chloride or bromide, which is then reacted with an excess of solid silver chromate, followed by collection of the combined unreacted silver chromate and chloride or bromide preipitate and AAS determination of the free chromate (equivalent of the chloride or bromide originally present) at 358.2 nm. The method was applied satisfactorily to a wide range of chlorine or bromine containing organic compounds with an average absolute error of ± 0.23 and a coefficient of variation (seven determinations) of better than 2%.     

Liquid-phase microextraction-gas chromatography-mass spectrometry for the determination of bromate, iodate, bromide and iodide in high-chloride matrix

In the determination of bromate and iodate, any free bromide and iodide present was quantitatively removed by anion exchange with silver chloride exploiting the differences in silver salts solubility product, being AgCl, 1.8 x 10(-10), AgBr, 5.0 x 10(-13), AgI, 8.3 x 10(-17), AgBrO(3), 5.5 x 10(-5) and AgIO(3), 3.1 x 10(-8). The oxyhalides were reduced with ascorbic acid to halides and converted to 4-bromo-2,6-dimethylaniline and 4-iodo-2,6-dimethylaniline by their reaction with 2-iodosobenzoate in the presence of 2,6-dimethylaniline at pH 6.4 and 2-3, respectively. Single drop microextraction (SDME) of the haloanilines in 2 microl of toluene and injection of the whole extract into GC-MS, or liquid-phase microextraction (LPME) into 50 microl of toluene and injection of 2 microl of extract, resulted in a sensitive method for bromate and iodate. The latter method of extraction has been found more robust, sensitive and to give better extraction in shorter period than SDME. Total bromine/iodine was determined without any treatment with silver chloride. High concentration of chloride in the matrix did not interfere. A rectilinear calibration graph was obtained for 0.05 microg-25 mg l(-1) of bromate/bromide and iodate/iodide, the limit of detection were 20 ng l(-1) of bromate, 15 ng l(-1) of iodate, 20 ng l(-1) of bromide and 10 ng l(-1) of iodide (by LPME in 50 microl of toluene). The method has been applied to seawater and table salt. From the pooled data, the average recovery of spiked oxyhalide/halide to real samples was in range 96.7-105.7% with RSD in range 1.6-6.5%.     

Separation of trace heavy metals from silver matrix by solid – liquid extraction for graphite-furnace atomic absorption spectrometry

 A silver sample (50–300 mg) was dissolved in 6 mol/l nitric acid and mixed with 6 mol/l hydrochloric acid to form silver chloride. The solution was evaporated to dryness and the residue was treated ultrasonically in 0.1 mol/l nitric acid for the extraction of trace impurities from the silver chloride. Traces of iron, copper, lead and bismuth were recovered in greater than 94% yields, though considerable amounts of cadmium were not extracted due to the strong occlusion in the silver chloride. The separation factor for the silver was about 10^-4; hence the trace heavy metals were immediately determined by graphite-furnace atomic absorption spectrometry without any interference. The validity of the method was confirmed by the analysis of certified reference material. The proposed method is simple and allows the detection of as little as 10 ng/g levels in silver samples. Received: 13 January 1995/Accepted: 29 March 1995     

Studies on purification of plutonium from silver ions

Precipitation and solvent extraction methods have been investigated for the purification of plutonium from silver from the solution generated during oxidative dissolution of plutonium oxide using Ag(II) ions. Initial experiments have been carried out using thorium as representative of plutonium. Selecting the optimum conditions, the experiments were repeated with plutonium. The results revealed that Pu can be purified from silver ions either by precipitating silver as silver chloride or silver metal followed by Pu(IV) oxalate precipitation or by selective extraction of Pu(IV) into 20% Aliquat-336 or 30% TBP.     

Silver based mercury film electrode: Part II. The influence of aging of electrode on the electrode processes of various metal ions

The cyclic voltammetric behaviour of 8 metal ions at solid silver amalgam electrodes prepared by aging of a thin silver based mercury film electrode (SBMFE) and by deposition of silver and mercury on platinum were investigated. It was established that such electrodes behave in relation to some metals (Pb, Bi, Sn) similarly as silver electrodes i.e. the cyclic curves obtained with these electrodes at concentration 10^?3M range show a prepeak-postpeak system corresponding to deposition and dissolution of the monolayer of deposit. On the other hand under the same conditions no prepeaks were observed for cadmium, zinc and thallium. In all cases investigated the heights of anodic stripping peaks were lower on curves obtained with aged SBMFE than on those obtained with fresh SBMFE having a mercury layer 1 μm thick.     

Liquid-liquid extraction of silver ion with benzothiacrown ether derivatives

The extraction behavior of mono-, poly-, anal bis-(benzothiacrown ether)s is studied for alkali, alkaline-earth, heavy, and transition metal ions in the presence of picrate. These ethers show high selectivity for silver ion. Silver extractions from binary and quaternary mixtures of silver with heavy or transition metal ions were successful, except for mixtures with mercury(II) ion. Silver was extracted from a copper ore with ca. 80% recovery.     

Determination of chloride and bromide in lead telluride and bismuth telluride systems

Summary An indirect analytical method, based on measurement of silver, for determining chloride and bromide in bismuth and lead tellurides was developed. The samples were dissolved in dilute nitric acid and the halides were separated as the silver salts by strong centrifugation. The excess of silver was directly determined in the sample solution by solvent extraction with dithizone in carbon tetrachloride and by spectrophotometric determination. Suitable conditions for masking interfering elements were established so that a very selective procedure for silver determination was achieved. Chloride and bromide down to 0.01 mole % could be determined. A procedure for determining chloride and bromide in the same sample with no interference from iodide, was also developed.

---

Zusammenfassung Ein indirektes, auf der Messung von Silber beruhendes Verfahren zur Bestimmung von Chlorid und Bromid in Wismut- und Bleitelluriden wurde entwickelt. Die Proben werden in verd. Salpetersäure gelöst und die Halogenide als Silbersalze scharf abzentrifugiert. Der Silberüberschuß wird unmittelbar aus dem Filtrat mit Dithizonlösung extrahiert und spektro-photometrisch gemessen. Geeignete Maßnahmen zur Maskierung störender Elemente wurden angegeben, so daß ein sehr selektives Verfahren zur Silberbestimmung vorliegt. Bis zu 0,01 Molprozent Chlorid und Bromid sind noch bestimmbar. Außerdem wurde ein Verfahren zur Chlorid- und Bromidbestimmung in Gegenwart von Jodid entwickelt.

     

离子液体中卤素离子杂质的离子色谱-直接电导检测法分析

研究了离子色谱-直接电导检测法分离测定离子液体中的卤素离子(F~-、Cl~-、Br~-)杂质.采用Shim-pack IC-A3阴离子交换色谱柱,考察了淋洗液种类及浓度、流速和色谱柱温度对分离测定的影响.最佳色谱条件为:以1.25 mmol/L邻苯二甲酸氢钾为淋洗液,流速1.5 mL/min,色谱柱温45 ℃.在此条件下可以基线分离卤素离子,且NO~-_3、BF~-_4、SO~(2-)_4不干扰测定.该法测定卤素离子的检出限(S/N=3)为0.02 ～0.11 mg/L,峰面积的相对标准偏差(n=5)不大于0.7%,F~-、Cl~- 和Br~- 的标准曲线的线性范围分别为0.1 ～50、0.1 ～50、0.5 ～100 mg/L.将方法用于烷基咪唑四氟硼酸盐离子液体中卤素离子杂质的测定,加标回收率为98% ～102%.     

Synthesis of silver nanowires and their applications in the electrochemical detection of halide

A silver nanowires modified platinum (Ag NWs/Pt) electrode was developed for simultaneous and selective determination of chloride, bromide and iodide ions by cyclic voltammetry in aqueous solutions. Silver nanowires were synthesized by an l-cysteine-assisted poly (vinyl pyrrolidone) (PVP)-mediated polyol route. X-ray diffraction (XRD) and scanning electron microscopy (SEM), transmission electron microscopy (TEM) and energy dispersive X-ray spectroscopy (EDS) were employed to investigate the prepared nanowires. The intrinsic high surface area and the fast electron transfer rate ascribed from the nanowire structure could further improve halide detection performance. The determination was based on measurement of the well-separated oxidation peak currents of respective silver halides formed on the surface of silver during an anodic potential sweep. The concentration range was linear from 50 μM to 20.2 mM for bromide and iodide and 200 μM to 20.2 mM for chloride, and the sensitivity was 0.059 μA/mM, 0.042 μA/mM and 0.032 μA/mM for chloride, bromide and iodide, respectively. The correlation coefficient was 0.999 in each case. The Ag NWs/Pt electrode offered a useful platform for the development of a highly sensitive halide sensor.     

An inorganic nano-sorbent based on nickel–aluminum–zirconium ternary-layered double hydroxide for solid-phase extraction of chloride ions

A well crystalline nickel?Caluminum?Czirconium ternary-layered double hydroxide was firstly synthesized and applied as a solid-phase extraction sorbent for the separation of trace levels of chloride ions from aqueous solutions. An indirect method was used for monitoring of the extracted chloride ions. For this purpose, the extracted chloride ions were passed through a reaction column containing silver chloranilate powder and the analyte was precipitated as silver chloride. The concentration of chloranilate ions released from the reaction column, which corresponds to the chloride ions concentration, was then determined spectrophotometrically at 530?nm. The effect of several parameters, such as pH, sample loading flow rate, elution conditions, amount of nano-sorbent, sample volume and effect of potential interfering ions on the recovery was investigated. In the optimum experimental conditions, the limit of detection (3?s) and enrichment factor were 0.12 and 40???g?mL^?1, respectively. The calibration graph using the pre-concentration system was linear in the range of 0.25?C3.00???g?mL^?1 with a correlation coefficient of 0.997. The validation of the presented method was checked by the analysis of two certified reference materials. The optimized method was successfully applied to the determination of chloride ions in waters, food and biological samples.     

The solvent extraction of trace antimony(V)

An investigation of the extraction of trace amounts of antimony(V) from aqueous hydrochloric acid solutions into various others and chloroform has been carried out. Before extractions were made, mutual solubility studies of the two-phased systems were conducted. Then extraction experiments were performed using original aqueous acid concentrations from 0 to 12N and non-aqueous phases of ethyl ether, isopropye ether, isoamyl ether, n-hexyl ether, and chloroform. Dielectric constant determinations were made in the equilibrated non-aqueous phases, and spectrophotormetric and salting-out studies were carried out on the ethyl ether system. It was found that the isopropyl ether system presents the most advantageous conditions for the extraction of trace antimony(V)     

Variability of selectivity coefficients of solid-state ion-selective electrodes

The generalized model for the selectivity mechanism of solid-state ion-selective electrodes has been experimentally verified. The experimental parameters investigated were the concentration of interfering ion, temperature and stirring. Among the systems studied were electrodes sensitive to chloride (bromide, iodide), bromide (chloride, iodide), iodide (chloride, bromide), silver (copper, lead), copper (silver, lead) and lead (silver, copper), the species given in brackets being considered as the interferents. The model has been confirmed except for cases where the concentration of ions formed at the electrode surface by metathesis is too small to be the factor that dictates the electrode potential.     

Influence of interfacial water layer on surface properties of silver halides: effect of pH on the isoelectric point

The hypothesis that pH dependent charge of interfacial water affects electrokinetic charge and electrokinetic potential of hydrophobic colloids, but not the (inner) surface potential was tested. It was found that isoelectric points of silver chloride, bromide and iodide shift to the higher pAg values in the acidic solutions, but that surface potential did not depend on pH. Isoelectric points of water at inert surfaces lie in the range 2相似文献   

Pressurized Hot Water Extraction of anthocyanins from red onion: A study on extraction and degradation rates

Pressurized Hot Water Extraction (PHWE) is a quick, efficient and environmentally friendly technique for extractions. However, when using PHWE to extract thermally unstable analytes, extraction and degradation effects occur at the same time, and thereby compete. At first, the extraction effect dominates, but degradation effects soon take over. In this paper, extraction and degradation rates of anthocyanins from red onion were studied with experiments in a static batch reactor at 110 °C. A total extraction curve was calculated with data from the actual extraction and degradation curves, showing that more anthocyanins, 21-36% depending on the species, could be extracted if no degradation occurred, but then longer extraction times would be required than those needed to reach the peak level in the apparent extraction curves. The results give information about the different kinetic processes competing during an extraction procedure.