基于血红蛋白-纳米磷酸钬复合材料的过氧化氢生物传感器

以Ho2O3为反应物,采用水热法制备了纳米磷酸钬(n-HoPO4),并利用场发射扫描电子显微镜(SEM)、能谱分析(EDS)对其进行形貌表征和元素组成分析.将n-HoPO4和血红蛋白(Hb)复合材料修饰于裸玻碳电极(GCE)表面构建生物传感器,实现了对H2O2的电化学检测.采用循环伏安(CV)和电化学交流阻抗(EIS)技术对修饰电极进行表征,结果表明,Hb/n-HoPO4/GCE对H2O2的还原具有良好的电化学催化效果;n-HoPO4具有良好的导电性和生物相容性,促进了Hb与工作电极间的直接电子转移.研究了不同pH值和电化学扫速对修饰电极响应电流的影响.在优化实验条件下,此生物传感器对H2O2在50 ～ 1000 μmol/L范围内表现出良好的线性关系,相关线性系数R=0.999,检出限为17 μmol/L(S/N=3).此生物传感器具有检测范围宽、稳定性和重现性好、抗干扰能力强等优点,可用于实际样品的检测.     

Novel Hydrogen Peroxide Biosensor Based on Hemoglobin Combined with Electrospinning Composite Nanofibers

A facile strategy to construct an amperometric biosensor was described for the determination of hydrogen peroxide (H₂O₂). This biosensor relied on an electrospinning gold nanoparticle-chitosan-poly(vinyl alcohol) composite nanofibers modified ITO electrode, followed by immobilization of hemoglobin (Hb) on the surface. The introduction of nanofibers and gold nanoparticles in the modification of electrode surface not only enhanced the surface area of the modified electrode for enzyme immobilization but also facilitated the electron transfer rate. Under optimum conditions, the sensor was characterized in terms of its morphology by scanning electron microscopy and its electroactivity by cyclic voltammetry and chronoamperometry. Scanning electron microscopy revealed that the obtained nanofibers were uniform. The chronoamperometric behavior of the modified electrode indicated that the immobilized Hb retained electrochemical activity inside the electrospinning fibrous membranes. The electrode responded linearly to H₂O₂ in a wider concentration range of 5.6 × 10^?7 M to 5.2 × 10^?2 M with a low detection limit (S/N = 3) of 1.98 × 10^?7 M and a short response time of ～4 s, suggesting a much better performance than that of other sensors. Moreover, the biosensor achieved bulk production and exhibited superior properties for the sensitive determination of H₂O₂, studied namely, long-term stability, good reproducibility, and high selectivity.     

Hemoglobin‐Titanate Composite Based Biosensor for the Amperometric Determination of Hydrogen Peroxide in Acidic Medium

A hemoglobin‐titanate composite based biosensor was chosen for determination of H₂O₂ in an acidic medium. CV results of the Hb‐titanate modified pyrolytic graphite electrode showed a pair of well‐defined, quasi‐reversible redox peaks centered at ?246 mV (vs. Ag/AgCl) in a pH 5.0 HAc‐NaAc buffer solution. The modified electrode exhibited good electrocatalytic response for monitoring H₂O₂ and had a large linear detection range from 20 μM to 3.2 mM with a detection limit of 8 μM (S/N=3) and a sensitivity of 29.7 mA M^?1 cm^?2 in the pH 5.0 solution. The biosensor also possessed good long term storage stability.     

Direct Electrochemistry of Hemoglobin Immobilized on Colloidal Gold‐Hydroxyapatite Nanocomposite for Electrocatalytic Detection of Hydrogen Peroxide

A novel nanocomposite of colloidal gold (GNPs) and hydroxyapatite nanotubes (Hap) was prepared for immobilization of a redox protein, hemoglobin (Hb), on glassy carbon electrode. The immobilized Hb showed fast direct electron transfer and excellent electrocatalytic behavior toward reduction of hydrogen peroxide. A synergic effect between GNPs and Hap for accelerating the surface electron transfer of Hb was observed, which led to a pair of redox peaks with a formal potential of (?340±2) mV at pH 7.0, and a new biosensor for hydrogen peroxide with a linear range from 0.5 to 25 μM and a limit of detection of 0.2 μM at 3σ. Owing to the good biocompatibility of the nanocomposite, the biosensor exhibited good stability and acceptable reproducibility. The as‐prepared nanocomposite film provided a good matrix for protein immobilization and biosensor preparation.     

Mediatorless Hydrogen Peroxide Biosensor Based on Horseradish Peroxidase Immobilized on 4‐Carboxyphenyl Film Electrografted on Gold Electrode

A novel method to fabricate a third‐generation hydrogen peroxide biosensor was reported. The electrode was first derivatized by electrochemical reduction of in situ generated 4‐carboxyphenyl diazonium salt (4‐CPDS) in acidic aqueous solution yielded stable 4‐carboxyphenyl (4‐CP) layer. The horseradish peroxidase (HRP) enzyme was then covalently immobilized by amidation between NH₂ terminus of enzyme and COOH terminus of 4‐CP film making use of the carbodiimide chemistry. Electrodeposition conditions used to control electrode functionalization density and film electron transfer kinetics were assessed by chronoamperometry and electrochemical impedance spectroscopy. The immobilized HRP displayed excellent electrocatalytic activity towards the reduction of hydrogen peroxide (H₂O₂) without any mediators. The effect of various operational parameters was explored for optimum analytical performance. The reported biosensor exhibited fast amperometric response (within 5 s) to H₂O₂. The detection limit of the biosensor was 5 μM, and linear range was from 20 μM to 20 mM. Furthermore, the biosensor exhibited high sensitivity, good reproducibility, and long‐term stability.     

Hydrogen Peroxide Biosensor Based on Immobilization of Hemoglobin on Au@Ag Nanoparticles Modified Carbon Ionic Liquid Electrode

A hydrogen peroxide (H₂O₂) biosensor based on the combination of Au@Ag core‐shell nanoparticles with a hemoglobin‐chitosan‐1‐butyl‐3‐methyl‐imidazolium tetrafluoroborate (Hb‐CHIT‐BMIM×BF₄) composite film was prepared. UV‐vis spectroscopy and transmission electron microscopy confirmed a core‐shell nanostructure of Au@Ag nanoparticle was successfully obtained. Cyclic voltammetric results showed a pair of well‐defined redox peaks appeared with the formal potential (E^O′) of ‐0.301 V (versus Ag/AgCl reference electrode) and the peak‐to‐peak separation (ΔE_p) was 84 mV in 0.1 M phosphate buffer solutions. Due to the synergetic effect of Au@Ag core‐shell nanoparticles and Hb‐CHIT‐BMIM×BF₄, the biosensor exhibited good electrocatalytic activity to the reduction of H₂O₂ in a linear range from 1.0 × 10^?6 to 1.0 × 10^?3 M with a detection limit of 4 × 10^?7 M (S/N = 3). The apparent Michaelis‐Menten constant (K_M) was estimated to be 4.4 × 10^?4 M, showing its high affinity. Thus, the study proved that the combination of Au@Ag core‐shell nanoparticles and Hb‐CHIT‐BMIM×BF₄ is able to open up new opportunities for the design of enzymatic biosensors.     

Immobilization of Hemoglobin on the Gold Colloid Modified Pretreated Glassy Carbon Electrode for Preparing a Novel Hydrogen Peroxide Biosensor

A novel hydrogen peroxide (H₂O₂) biosensor was developed by immobilizing hemoglobin on the gold colloid modified electrochemical pretreated glassy carbon electrode (PGCE) via the bridging of an ethylenediamine monolayer. This biosensor was characterized by UV-vis reflection spectroscopy (UV-vis), electrochemical impendence spectroscopy (EIS) and cyclic voltammetry (CV). The immobilized Hb exhibited excellent electrocatalytic activity for hydrogen peroxide. The Michaelis–Menten constant (K _m) was 3.6 mM. The currents were proportional to the H₂O₂ concentration from 2.6 × 10⁻⁷ to 7.0 × 10⁻³ M, and the detection limit was as low as 1.0 × 10⁻⁷ M (S/N = 3).     

Novel Amperometric Hydrogen Peroxide Biosensor Based on Horseradish Peroxidase Azide Covalently Immobilized on Ethynyl‐Modified Screen‐Printed Carbon Electrode via Click Chemistry

A novel, simple and versatile protocol for covalent immobilization of horseradish peroxidase (HRP) on screen‐printed carbon electrode (SPCE) based on the combination of diazonium salt electrografting and click chemistry has been successfully developed. The ethynyl‐terminated monolayers are obtained by diazonium salt electrografting, then, in the presence of copper (I) catalyst, the ethynyl modified surfaces reacted efficiently and rapidly with horseradish peroxidase bearing an azide function (azido‐HRP), thus forming a covalent 1,2,3‐triazole linkage by means of click chemistry. All the experimental results suggested that HRP was immobilized onto the electrode surface successfully without denaturation. Furthermore, the immobilized HRP showed a fast electrocatalytic reduction for H₂O₂. A linear range from 5.0 to 50.0 µM in a phosphate buffer (pH 5.5) with detection limit of 0.50 µM and sensitivity of 0.23 nA/µM were obtained. The heterogeneous electron transfer rate constant K_ct was 1.52±0.22 s^?1 and the apparent Michaelis? Menten constant was calculated to be 0.028 mM. The HRP‐functionalized electrode demonstrated a good reproducibility and long‐term stability.     

马铃薯组织过氧化氢生物传感器的研究

以马铃薯组织作为生物催化材料与氧电极结合研制成过氧化氢传感器，具有灵敏度高、选择性好和寿命长等特点．响应时间５ｍｉｎ，过氧化氢浓度在２×１０－４－４×１０－３ｍｏｌ／Ｌ之间与响应有线性关系，检出限５×１０－５ｍｏｌ／Ｌ．     

Reagentless Biosensor for Hydrogen Peroxide Based on the Immobilization of Hemoglobin in Platinum Nanoparticles Enhanced Poly(chloromethyl thiirane) Cross‐linked Chitosan Hybrid Film

An unmediated hydrogen peroxide (H₂O₂) biosensor was prepared by co‐immobilizing hemoglobin (Hb) with platinum nanoparticles enhanced poly(chloromethyl thiirane) cross‐linked chitosan (CCCS‐PNs) hybrid film. CCCS could provide a biocompatible microenvironment for Hb and PNs could accelerate the electron transfer between Hb and the electrode. Spectroscopic analysis indicated that the immobilized Hb could maintain its native structure in the CCCS‐PNs hybrid film. Entrapped Hb exhibited direct electrochemistry for its heme Fe(III)/Fe(II) redox couples at ?0.396 V in the CCCS‐PNs hybrid film, as well as peroxidase‐like activity to the reduction of hydrogen peroxide without the aid of an electron mediator.     

A Novel Hydrogen Peroxide Biosensor Based on the Synergistic Effect of Gold‐Platinum Alloy Nanoparticles/Polyaniline Nanotube/Chitosan Nanocomposite Membrane

Based on the immobilization of horseradish peroxidase (HRP) in chitosan(CS) on a glassy carbon electrode (GCE) modified with the Au‐Pt alloy nanoparticles (NPs) / polyaniline nanotube (nanoPAN) nanocomposite film, a novel hydrogen peroxide biosensor was constructed. The modified processes of GCE were monitored by cyclic voltammetry and electrochemical impedance spectroscopy. Au‐PtNPs/nanoPAN/CS had a better synergistic electrochemical effect than did AuNPs/nanoPAN/CS or PtNPs/nanoPAN/CS. The amperometric response of the biosensor towards H₂O₂ was investigated by successively adding aliquots of H₂O₂ to a continuous stirring phosphate buffer solution under the optimized conditions. Because Au‐PtNPs have unique catalytic properties and good biocompatibility, and especially Au‐PtNPs and nanoPAN have synergistic augmentation for facilitating electron‐transfer, the biosensor displayed a fast response time (<2 s) and broad linear response to H₂O₂ in the range from 1.0 to 2200 μmol L^?1 with a relatively low detection limit of 0.5 μmol L^?1 at 3 times the background noise. Moreover, the biosensor can be applied in practical analysis and exhibited high sensitivity, good reproducibility, and long‐term stability.     

A Third‐Generation Hydrogen Peroxide Biosensor Based on Horseradish Peroxidase Covalently Immobilized on Electrografted Organic Film on Screen‐Printed Carbon Electrode

A new convenient strategy to fabricate a third‐generation hydrogen peroxide biosensor was described. The screen‐printed carbon electrode (SPCE) was first modified with a layer of 4‐nitrophenyl assembled from the 4‐nitroaniline diazonium salt synthesized in situ in acidic aqueous solution. Next, the nitro groups were converted to amines followed by crosslinking to the horseradish peroxidase (HRP) by glutaraldehyde. The redox chemistry of the active center of the HRP was observed and the HRP‐modified electrode displayed electrocatalytic activity towards the reduction of hydrogen peroxide (H₂O₂) without any mediators. H₂O₂ was determined in a linear range from 5.0 μM to 50.0 μM, with a detection limit of 1.0 μM. Furthermore, the biosensor exhibited fast amperometric response, good reproducibility and long‐term stability.     

基于等离子体聚合膜固定酶的H2O2生物传感器

以玻碳电极为基础电极,用微波等离子体技术聚合沉积聚乙二胺等离子体膜,使之形成带氨基功能团的表面,再通过戊二醛交联共价固定辣根过氧化物酶,制得H2O2生物传感器.探讨了等离子体聚合膜的形成条件(如放电功率、单体流速、单体气压和聚合时间),讨论了工作电位、介体浓度和pH值对传感器响应的影响.此外,用红外光谱对等离子体聚合膜进行了表征.该传感器在5×10-7～1.1×10-3mol/LH2O2浓度范围内有线性响应,最低检测限为0.3μmol/L.将此传感器用于实际试样回收率的测定,结果良好.     

A Novel Biomimetic Hydrogen Peroxide Biosensor Based on Pt Flowers‐decorated Fe3O4/Graphene Nanocomposite

A sensitive and selective amperometric H₂O₂ biosensor was obtained by utilizing the electrodeposition of Pt flowers on iron oxide‐reduced graphene oxide (Fe₃O₄/rGO) nanocomposite modified glassy carbon electrode (GCE). The morphology of Fe₃O₄/rGO and Pt/Fe₃O₄/rGO was characterized by transmission electron microscopy (TEM) and scanning electron microscopy (SEM), respectively. The step‐wise modification and the electrochemical characteristics of the resulting biosensor were characterized by cyclic voltammetry (CV) and chronoamperometry methods. Thanks to the fast electron transfer at the Pt/Fe₃O₄/rGO electrode interface, the developed biosensor exhibits a fast and linear amperometric response upon H₂O₂. The linear range of Pt/Fe₃O₄/rGO is 0.1∼2.4 mM (R²=0.998), with a sensitivity of 6.875 μA/mM and a detection limit of 1.58 μM (S/N=3). In addition, the prepared biosensor also provides good anti‐interferent ability and long‐term stability due to the favorable biocompatibility of the electrode interface. The proposed sensor will become a reliable and effective tool for monitoring and sensing the H₂O₂ in complicate environment.     

Direct Electrochemistry of Hemoglobin Immobilized on Carbon‐Coated Iron Nanoparticles for Amperometric Detection of Hydrogen Peroxide

A novel method for preparation of hydrogen peroxide biosensor was presented based on immobilization of hemoglobin (Hb) on carbon‐coated iron nanoparticles (CIN). CIN was firstly dispersed in a chitosan solution and cast onto a glassy carbon electrode to form a CIN/chitosan composite film modified electrode. Hb was then immobilized onto the composite film with the cross‐linking of glutaraldehyde. The immobilized Hb displayed a pair of stable and quasireversible redox peaks and excellent electrocatalytic reduction of hydrogen peroxide (H₂O₂), which leading to an unmediated biosensor for H₂O₂. The electrocatalytic response exhibited a linear dependence on H₂O₂ concentration in a wide range from 3.1 μM to 4.0 mM with a detection limit of 1.2 μM (S/N=3). The designed biosensor exhibited acceptable stability, long‐term life and good reproducibility.     

Hydrogen peroxide biosensor based on hemoglobin modified zirconia nanoparticles-grafted collagen matrix

A novel method for the immobilization of hemoglobin (Hb) and preparation of reagentless biosensor was proposed using a biocompatible non-toxic zirconia enhanced grafted collagen tri-helix scaffold. The formed membrane was characterized with UV-vis and FT-IR spectroscopy, scanning electron microscope and electrochemical methods. The Hb immobilized in the matrix showed excellent direct electrochemistry with an electron transfer rate constant of 6.46 s⁻¹ and electrocatalytic activity to the reduction of hydrogen peroxide. The apparent Michaelis-Menten constant for H₂O₂ was 0.026 mM, showing good affinity. Based on the direct electrochemistry, a new biosensor for H₂O₂ ranging from 0.8 to 132 μM was constructed. Owing to the porous structure and high enzyme loading of the matrix the biosensor exhibited low limit of detection of 0.12 μM at 3σ, fast response less than 5 s and high sensitivity of 45.6 mA M⁻¹ cm⁻². The biosensor exhibited acceptable stability and reproducibility. ZrO₂-grafted collagen provided a good matrix for protein immobilization and biosensing preparation. This method was useful for monitoring H₂O₂ in practical samples with the satisfactory results.     

磁性纳米微球-血红蛋白修饰电极的电化学行为及对H2O2电催化还原的研究

将天然高分子壳聚糖(CS)包裹碳包铁的磁性纳米微球(CFN/CS)修饰于玻碳电极表面,并利用戊二醛将血红蛋白(Hb)交联在CFN/CS上,制备了Hb-CFN/CS-GC电极。循环伏安法和电化学交流阻抗法实验结果表明,Hb在CFN/CS-GC电极表面仍保持较好的生物活性,能稳定有效地进行直接电子转移反应。电化学研究表明该修饰电极对H2O2有良好的电催化还原作用,在pH 7.0的磷酸盐(PBS)介质中,H2O2在5.2×10-5~2.3×10-3mol/L浓度范围内,其浓度与还原峰电流呈良好线性关系,检出限为8.7×10-6mol/L。该修饰电极有着良好的重现性和稳定性。     

An Organic Sol‐Gel Film as Modifier to Construct Biosensor

A new amperometric biosensor for hydrogen peroxide (H₂O₂) was developed by adsorbing hemoglobin (Hb) on an organic sol‐gel film. The organic sol‐gel was prepared using resorcinol and formaldehyde as monomers. This sol‐gel film shows a biocompatible microenvironment for retaining the native activity of the adsorbed Hb. The direct electron transfer between Hb and electrode is achieved. Hb adsorbed on the film shows an enzyme‐like catalytic activity for the reduction of H₂O₂. The reduction peak currents are proportional linearly to the concentration of hydrogen peroxide in the range of 6×10^?8 to 3.6×10^?6 M, with a detection limit of 2.4×10^?8 M (S/N=3). This research enlarges the applications of organic sol‐gel materials in biosensor field.     

A Third‐Generation Hydrogen Peroxide Biosensor Based on Horseradish Peroxidase Immobilized in Carbon Nanotubes/ SBA‐15 Film

A new third‐generation biosensor for H₂O₂ assay was developed on the basis of the immobilization of horseradish peroxidase (HRP) in a nanocomposite film of carbon nanotubes (CNTs)‐SBA‐15 modified gold electrode. The biological activity of HRP immobilizing in the composite film was characterized by UV‐vis spectra. The HRP immobilized in the nanocomposite matrix displayed excellent electrocatalytic activity to the reduction of H₂O₂. The effects of the experimental variables such as solution pH and working potential were investigated using steady‐state amperometry. Under the optimal conditions, the resulting biosensor showed a linear range from 1 µM to 7 mM and a detection limit of 0.5 µM (S/N=3). Moreover, the stability and reproducibility of this biosensor were evaluated with satisfactory results.     

Amperometric Biosensor for Hydrogen Peroxide Based on Myoglobin Doped Multiwalled Carbon Nanotube Enhanced Grafted Collagen Matrix

Abstract

A reagentless H₂O₂ sensor based on the direct electron transfer of myoglobin (Mb) doped in multiwalled carbon nanotubes enhanced grafted collagen matrix is proposed. The formal potential of the immobilized Mb was ?0.358 V with a surface coverage of 4.0×10^?10 mol cm^?2. The electrode process was surface‐controlled with an electron transfer rate constant of 9.7 s^?1. The proposed biosensor displayed an excellent electrocatalytic response to the reduction of H₂O₂ with a linear range from 0.6 to 39.0 µM. Owing to the good biocompatibility and high enzyme loading of the matrix the biosensor exhibited acceptable stability and reproducibility.