纳米金–壳聚糖修饰电极循环伏安法测定抗坏血酸

介绍纳米金–壳聚糖修饰电极的制备方法及其测定抗坏血酸的分析应用。采用电沉积方法,将氯金酸与壳聚糖的混合电解液直接共沉积,制备了壳聚糖–纳米金修饰玻碳电极的电化学传感器。利用循环伏安法研究了抗坏血酸浓度、p H值等对抗坏血酸在修饰电极上的电化学行为的影响。实验结果表明,修饰电极对抗坏血酸具有良好的电催化氧化作用,抗坏血酸浓度在5×10~(–5)~1×10~(–3) mol/L范围内线性良好,回归方程为I_p=0.433 8c+0.881 9,相关系数为0.998 71。该法可指导纳米金–壳聚糖修饰电极的制备及抗坏血酸含量的测定。     

Determination of glycosylation sites in O-linked glycopeptides: A sensitive mass spectrometric protocol

A sensitive mass spectrometric method for the specific identification of O-glycosylation sites in glycopeptides is presented. Reductive β-elimination liberates a peptide containing a specifically modified amino acid at the former site of carbohydrate attachment. Mass spectrometry is used to determine the sequence of the modified peptide, in which the position of the modified amino acid marks the site of O-glycosylation. The method also provides information on the carbohydrate chain and is applicable at the low nanomolar level.     

Isolation of a novel,crystalline cellulose material from the spent liquor of cellulose nanocrystals (CNCs)

We have modified the standard sulphuric acid hydrolysis method for the production of cellulose nanocrystals (CNCs) to successfully isolate a novel, highly crystalline cellulose material from the spent liquor of CNCs. The novel material has a cellulose II crystal structure that is distinctly different from the cellulose I crystal structure of CNCs. The modified method uses a shorter time for the hydrolysis, followed by maintaining a high residual acid concentration for the separation of the spent liquor and CNCs, and by adding the spent liquor to water. The modified method offers an opportunity to concurrently produce CNCs in up to ~40 % yield and the novel, highly crystalline, sulphated cellulose II in ~15 % yield in separate and pure forms from sulphuric acid hydrolysis of a commercial northern bleached softwood kraft pulp. It can potentially reduce the production cost of CNCs, allow easier downstream processing of CNCs and recovery of sulphuric acid, and generate a new cellulose bio-material for product development.     

A modified acid digestion procedure for extraction of tungsten from soil

Interest in tungsten occurrence and geochemistry is increasing due to increased use of tungsten compounds and its unknown biochemical effects. Tungsten has a complex geochemistry, existing in most environmental matrices as the soluble and mobile tungstate anion, as well as poly- and heteropolytungstates. Because the geochemistry of tungsten is substantially different than most trace metals, including the formation of insoluble species under acidic conditions, it is not extracted from soil matrices using standard acid digestion procedures. Therefore, the current work describes a modification to a commonly used acid digestion procedure to facilitate quantification of tungsten in soil matrices. Traditional soil digestion procedures, using nitric and hydrochloric acids with hydrogen peroxide yield <1 up to 50% recovery on soil matrix spike samples, whereas the modified method reported here, which includes the addition of phosphoric acid, yields spike recoveries in the 76-98% range. Comparison of the standard and modified digestion procedures on National Institute of Standards and Technology Standard Reference Materials yielded significantly improved tungsten recoveries for the phosphoric acid modified method. The modified method also produces comparable results for other acid extractable metals as the standard methods, and therefore can be used simultaneously for tungsten and other metals of interest.     

铜氮杂配合物修饰金电极对抗坏血酸的分析测定

本实验制备了一种新型的氮杂铜配合物修饰金电极,该电极可用于抗坏血酸的测定。采用循环伏安法和扫描电化学显微镜技术对电极进行了表征。该修饰电极可催化氧化抗坏血酸,相对于裸电极抗坏血酸在修饰电极上氧化电位移动了250mV,并且氧化电流在抗坏血酸的浓度为5.0×10−7 to 4.0×10−5 mol/L时呈线性关系,检测限为4.8×10-8 mol/L。用此方法测定抗坏血酸与文献报道的测定结果一致,这表明该电极可用作抗坏血酸测定的电化学传感器。     

聚茜素红-多壁碳纳米管复合膜修饰电极的研制及叶酸含量测定

采用电聚合方法将茜素红（AR）非共价修饰到多壁碳纳米管（MWCNTs）上,制得了PAR/MWCNTs/GC电极,该电极对叶酸（FA）具有良好的电催化作用. 结果表明,在最佳实验条件下,在-0.63 V处叶酸还原峰电流与浓度（1.25×10^-6 ~ 4.00×10^-5 mol·L^-1）呈现良好线性关系,相关系数0.9985. 用标准加入法检测了回收率,其值达92.0% ~ 102.0%. 该电极制作简单,有良好的稳定性．     

Electrochemical Characterization of Polymerized Cresol Red Film Modified Glassy Carbon Electrode and Separation of Electrocatalytic Responses for Ascorbic Acid and Dopamine Oxidation

A cresol red modified glassy carbon electrode was prepared using an electrochemical method. The cyclic voltammograms of the modified electrode indicate the presence of a couple of well-defined redox peaks, and the formal potential shifts in the negative direction with increasing solution pH. The modified electrode exhibits high electrocatalytic activity toward ascorbic acid oxidation, with an overpotential of 300 mV less than that of bare glassy carbon electrodes, and drastic enhancement of the anodic currents. The calibration graph obtained by linear sweep voltammetry for ascorbic acid is linear in the range of 50∼500 µM. The electrode markedly enhances the current response of dopamine and can separate the electrochemical responses of ascorbic acid and dopamine. The separation between the anodic peak potentials of ascorbic acid and dopamine is 190 mV by cyclic voltammetry. The linear sweep voltammetric peak currents for dopamine in the presence of 2 mM ascorbic acid vary linearly with a concentration of between 10 and 100 µM.     

基于对羟基苯硼酸为前驱体的金纳米粒子修饰电极电化学检测过氧化氢

以对羟基苯硼酸为前驱体,利用H₂O₂可以定量氧化对羟基苯硼酸产生对羟基苯酚的原理,以反应产物对羟基苯酚为电化学信号物质,结合金纳米粒子修饰玻碳电极（AuNPs/GCE）,发展了一种间接检测H₂O₂的电化学方法. 由于AuNPs/GCE具有有效电子传递性能和比表面积大等优点,对硼酸氧化产物具有较高的催化活性,因此在含1.0 mmol•L^-1对羟基苯硼酸的0.1mol•L^-1 pH 7.5 PBS中,AuNPs/GCE可以检测到1.0 ~ 1.0 × 10³ μmol•L^-1的H₂O₂,检测限为0.5μmol•L^-1. 同时,该方法具有良好的选择性和重现性,且操作简单、速度快、价格低廉,非常适用于实际样品中H₂O₂含量的测定.     

Extraction of uranium with crown ether carboxylic acids for neutron activation analysis

Uranium in aqueous solution can be extracted by sym-dibenzo-16-crown-5-oxy-acetic acid and its modified analogue 2-/sym-dibenzo-16-crown-5-oxy/-hexanoic acid into chloroform in the pH range 5.5–6.0. The extraction method combined with neutron activation analysis provides a sensitive method for the determination of uranium in natural waters.     

Multilayer films of carbon nanotubes and redox polymer on screen-printed carbon electrodes for electrocatalysis of ascorbic acid

Multilayer films containing multiwall carbon nanotubes and redox polymer were successfully fabricated on a screen-printed carbon electrode using layer-by-layer (LBL) assembled method. UV-vis spectroscopy, X-ray photoelectron spectroscopy, field-emission scanning electron microscopy and electrochemical method were used to characterize the assembled multilayer films. The multilayer films modified electrodes exhibited good electrocatalytic activity towards the oxidation of ascorbic acid (AA). Compared with the bare electrode, the oxidation peak potential negatively shifted about 350 mV (versus Ag/AgCl). Furthermore, the modified screen-printed carbon electrodes (SPCEs) could be used for the determination of ascorbic acid in real samples.     

Voltammetric Determination of Adrenaline Using a Poly(1‐Methylpyrrole) Modified Glassy Carbon Electrode

A voltammetric method using a poly(1‐methylpyrrole) modified glassy carbon electrode was developed for the quantification of adrenaline. The modified electrode exhibited stable and sensitive current responses towards adrenaline. Compared with a bare GCE, the modified electrode exhibits a remarkable shift of the oxidation potentials of adrenaline in the cathodic direction and a drastic enhancement of the anodic current response. The separation between anodic and cathodic peak potentials (ΔEp) for adrenaline is 30 mV in 0.1 M phosphate buffer solution (PBS) at pH 4.0 at modified glassy carbon electrodes. The linear current response was obtained in the range of 7.5 × 10^?7 to 2.0 × 10^?4 M with a detection limit of 1.68 × 10^?7 M for adrenaline by square wave voltammetry. The poly(1‐methypyrrole)/GCE was also effective to simultaneously determine adrenaline, ascorbic acid and uric acid in a mixture and resolved the overlapping anodic peaks of these three species into three well‐defined voltammetric peaks in cyclic voltammetry. The modified electrode has been successfully applied for the determination of adrenaline in pharmaceuticals. The proposed method showed excellent stability and reproducibility.     

CdSe量子点修饰电极电化学发光法测定叶酸

制备了水溶性的CdSe量子点,用紫外光谱和荧光光谱对其进行了表征.并将其修饰到金电极的表面,得到了CdSe量子点修饰电极(CdSe/GE),研究了其电化学发光性质.结果表明:在强碱介质中,CdSe/GE对鲁米诺电化学发光具有增敏作用,在此发光体系中加入叶酸后,会产生进一步增强的电化学发光信号,由此建立了电化学发光检测叶酸的新方法.考察了缓冲溶液pH值、鲁米诺的浓度和扫速等条件对电化学发光强度的影响.在优化的实验条件下,叶酸在1×10~(-13)~1.1×10~(-4) mol/L浓度范围内与相对发光强度(ΔI)呈现良好的线性关系,检测限为6.0×10~(-14) mol/L(S/N=3),并用于市售叶酸片剂中叶酸的测定,得到令人满意的实验结果.     

Fabrication and characterization of poly 2-napthol orange film modified electrode and its application to selective detection of dopamine

The present work is based on the use of a redox mediator containing an azo group for the selective determination of dopamine in the presence of uric acid and ascorbic acid by electrochemical method. A modified electrode was prepared by electrochemical polymerization of the poly 2-napthol orange film (P2NO) on the paraffin wax-impregnated graphite electrode (PIGE) by applying potential between ?0.6 and 0.8 V at scan rate of 50 mV s^?1 for 30 segments. The modified P2NO film electrode was characterized by ATR-IR spectroscopy, FE-SEM, cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS), differential pulse voltammetry (DPV), hydrodynamic voltammetry (HDV), and chronoamperometry (CA). The P2NO film modified electrode exhibited selective determination of dopamine in the presence of uric acid and ascorbic acid, and the electrocatalytic activity for oxidation of dopamine was excellent. The linear range for the determination of dopamine was 0.6 to 250 μM with a limit of detection of 0.13 μM. The modified P2NO electrode showed good stability and reproducibility. The modified electrode was used for real sample analysis such as human blood serum, rat blood serum, and pharmaceutical samples (dopamine hydrochloride injection). The results obtained were found to be satisfactory.     

A Highly Selective Amperometric Hydrogen Peroxide Sensor Based on Silicomolybdate‐Doped‐Glutaraldehyde‐Cross‐Linked Poly‐L‐Lysine Film Modified Glassy Carbon Electrode

Silicomolybdate‐doped‐glutaraldehyde‐cross‐linked poly‐L ‐lysine (PLL‐GA‐SiMo) film modified glassy carbon electrode was prepared by means of electrostatically trapping the silicomolybdate anion in the cationic film. The PLL‐GA‐SiMo film was stable and the charge transport through the film was fast. The modified electrode shows excellent electrocatalytic activity towards hydrogen peroxide reduction with significant reduction of overpotential, however, not responded to potential interferrents such as dopamine, ascorbic acid and uric acid. This unique feature of PLL‐GA‐SiMo modified electrode allowed for the development of a highly selective method for the determination of H₂O₂ in the presence of interferents.     

Peptide nucleic acid and amino acid modified peptide nucleic acid analysis by capillary zone electrophoresis

A rapid, high resolution, and low sample consumption CZE method is developed for peptide nucleic acid (PNA) analysis for the first time. 30% v/v acetonitrile in PNA sample and 20% v/v acetonitrile in 50 mM borax‐boric acid (pH 8.7) as BGE were employed after optimization. The calibration curves were linear for PNA concentration ranging from 1 to 50 μmol/L. LOD and LOQ of PNA were 0.2 and 1.0 μmol/L, respectively. Since the commercially available reagent gives rise to huge PNA peak and an apparent impurity peak, the purity of PNA was evaluated to be about 81.4% by CZE method, obviously lower than the supplier's purity value of 99.9% evaluated by RP–HPLC, and also lower than 94.8% determined with RP–HPLC by our research group. The CZE method takes only 5 min, needs only 90 nL PNA, much less than 20 min and 20 μL PNA in RP–HPLC method. Moreover, the CZE method is applicable for the analysis of glutamic acid modified and lysine modified PNAs, they show different migration time with their corresponding complementary PNAs. Our results show CZE provides a new choice for PNA and modified PNA analysis, also their purity or quality evaluation.     

多产低碳烯烃及柴油用分子筛的设计

目前,催化裂化的原料大多是蜡油和减压渣油的混合油,或全部的常压渣油 .其相对分子量范围很宽,组成十分复杂 .为了分别对待大小不同的分子和不同碳氢比化合物的裂化性能,现代催化裂化催化剂应具有梯度孔结构与梯度酸中心的优化结构配置 .而目前催化裂化的主导分子筛 USY二次孔含量还不能满足原料油日趋变重的需求,并且滞留在分子筛孔 /笼内的非骨架铝限制了其选择性的进一步提高,因此有必要对其结构进一步修饰 .　　本研究在 USY基础上合成新的催化裂化多产低碳烯烃和柴油用分子筛催化剂 .新型 USY基分子筛从晶体结构、孔容及孔…     

Calorimetric evaluation of activated carbons modified for phenol and 2,4-dinitrophenol adsorption

Two commercial activated carbons with differences in their superficial chemistry, one granular and the other pelletised, were modified for use in phenol and 2,4-dinitrophenol adsorption. In this paper, changes to the activated carbon surface will be evaluated from their immersion calorimetry in water and benzene, and they will then be compared with Area BET, chemical parameters, micropore size distributions and hydrophobicity factors of the modified activated carbons. The activated carbons were modified using 60 % solutions of phosphoric acid (H₃PO₄), nitric acid (HNO₃), zinc chloride (ZnCl₂) and potassium hydroxide (KOH); the activated carbon/solution ratio was 1:3 and impregnation was conducted 291 K for a period of 72 h before samples were washed until a constant pH was obtained. Water immersion calorimetry showed that the best results were obtained from activated carbons modified with nitric acid, which increased from ?10.6 to ?29.8 J g^?1 for modified granular activated carbon, and ?30.9 to ?129.3 J g^?1 for pelletised activated carbon. Additionally, they showed the best results in phenol and 2.4-dititrophenol adsorption. Those results indicate that impregnation with nitric acid under the employed conditions could generate a greater presence of oxygenated groups on their surface, which favours hydrogen bond formation and the increased adsorption of polar compounds. It should also be noted that immersion enthalpy in benzene for modified activated carbon with nitric acid is the method with the lowest value, which is consistent with the increased presence of polar groups on its surface. Regarding hydrophobicity factors, it was observed that granular carbons modified with nitric acid and potassium hydroxide have the lowest ratios, indicating greater interaction with water.     

Thin self-assembled monolayer for voltammetrically monitoring nicotinic acid in food

A novel and sensitive method for the determination of nicotinic acid was proposed and based on voltammetric behavior of nicotinic acid on a self-assembled monolayer of mercaptoacetic acid coated gold electrode. The adsorption-controlled anodic peak current for the oxidation of nicotinic acid on mercaptoacetic acid covered gold electrode was affected by the type and pH value of supporting electrolyte and by accumulation potential as well as by accumulation time, and enhanced linearly with the concentration of nicotinic acid in the range of 0.8 mM–0.45 μM with a detection limit of 0.14 μM. The proposed method was utilized successfully for the monitoring of nicotinic acid in food. The possible interaction of nicotinic acid with mercaptoacetic acid, which is responsible for the enhanced response of nicotinic acid on modified electrode, was also suggested.     

Detection of dopamine using self-assembled diazoresin/single-walled carbon nanotube modified electrodes

Ultrathin films of diazoresin(DR)/single-walled carbon nanotube(SWNT) were fabricated on thioglycollic acid(TGA) decorated gold(Au) electrodes by the self-assembly method combined with the photocrosslinlcing technique.The electrochemical behavior of dopamine(DA) at the DR/SWNT modified electrodes was studied using the cyclic voltammetry(CV) and differential pulse voltammetry(DPV) methods.Under the optimal conditions,a linear CV response to DA concentration from 1 μmol/L to 40 μmol/L was observed,and the detection limit of DA was 2.1 ×10~(-3) μmol/L via the DPV method in the presence of 10 μmol/L of uric acid(UA) or 2.5 × 10~(-3) μmol/L via the DPV method in the presence of10 μmol/L of ascorbic acid(AA).Moreover,the modified electrodes exhibited good reproducibility and sensitivity,demonstrating its feasibility for analytical purposes.     

Facile and green methodology for surface‐grafted Al2O3 nanoparticles with biocompatible molecules: preparation of the poly(vinyl alcohol)@poly(vinyl pyrrolidone) nanocomposites

The present work describes preparation of modified alumina with biocompatible, water soluble, and treating agents such as citric acid and ascorbic acid. Also, the influence of the modified nanoparticles (NPs) into the blend of poly(vinyl alcohol)@poly(vinyl pyrrolidone) (50/50) matrix was studied. At first, citric acid and ascorbic acid as environmental friendly agents were grafted on the surface of Al₂O₃ NPs. Then, nanocomposites (NCs) with different amounts of modified Al₂O₃ NPs were prepared via a simple ultrasonic method. The characterizations of the molecular structure of the NCs specified that chemical and physical interactions happened between inorganic and organic counterparts. The mutual effect of modified NPs into the polymer matrix was investigated on the structural, interfacial interaction, thermal stability, and optical properties. The results from morphological characterization confirmed changes in morphology of poly(vinyl alcohol) and poly(vinyl pyrrolidone) after loading NPs. Uniform dispersion of modified spherical Al₂O₃ NPs powders into the matrix of 50/50 polymers was detected by field emission scanning electron microscopy and energy‐dispersive X‐ray. Adding M‐NPs into the polymer matrix expressively improved the thermal stability of NCs. Peaks in ultraviolet–visible spectra were shifted to the higher absorption. Copyright © 2017 John Wiley & Sons, Ltd.