阳极氧化AZ91D镁合金在氯化钠稀溶液中的腐蚀行为

利用盐雾实验、极化曲线扫描、电化学阻抗谱和电化学噪声技术等电化学研究方法结合扫描电镜表面观测技术对AZ91D镁合金氧化膜在1%(w)氯化钠溶液中的耐蚀性能进行了评价. 结果表明, 氧化前后的镁合金腐蚀行为发生明显改变, 如未封孔的阳极氧化膜耐中性5%氯化钠盐雾试验时间超过200 h; 氧化后的镁合金自腐蚀电位明显正移, 点蚀诱导期延长; 阳极氧化膜的高频阻抗约为裸露镁合金的数千倍, 这些变化证明阳极氧化处理使镁合金获取了十分优异的耐蚀性能. 首次利用分形维数Df的变化规律初步描述氧化后AZ91D镁合金的腐蚀过程. 可以发现随着浸泡时间的延长, Df呈现出初期快速增长, 随后出现波动, 最后稍有降低的变化过程. 这种现象对应于氧化后AZ91D 镁合金在1%氯化钠溶液中腐蚀的三个阶段.     

预处理对镁合金镧转化膜及耐腐蚀性能的影响

为了提高镁合金镧转化膜的耐腐蚀性能,通过容量法和电化学方法研究了预处理对镁合金AX91D镧转化膜在5%NaCl溶液中腐蚀行为的影响.利用扫描电子显微镜(SEM)和能量色散谱仪(EDS)研究了膜层表面形貌及其组成,通过电极电位的跟踪测试研究了镧转化膜的成膜过程.结果表明:预处理不改变镧转化成膜过程的基本规律,但有助于镧的氧化物沉积;提高了镁合金镧转化膜的耐腐蚀性能,浸泡30 h其耐腐蚀性能与传统的封闭的铬酸盐转化膜相当.     

AZ31镁合金表面聚吡咯的化学氧化合成及其耐蚀性能

以对甲苯磺酸钠为掺杂剂, 三氯化铁为氧化剂, 用化学氧化聚合法在AZ31 镁合金表面制备聚吡咯(PPy)膜. 采用傅里叶变换红外(FTIR)光谱分析了镁合金表面聚吡咯膜结构, 通过电化学极化曲线、电化学阻抗谱(EIS)研究了其耐蚀性能, 通过扫描电子显微镜(SEM)、X射线能量散射谱(EDS)分析了表面形貌和成分. 和镁合金裸样相比, 聚吡咯膜对镁合金腐蚀有一定的抑制作用. 硅烷预处理改善了镁合金/聚吡咯体系的耐腐蚀性能, 使腐蚀电位较镁合金裸样正移了110 mV, 电流密度减小了约2个数量级.     

镁合金阳极氧化膜的结构、成分及其耐蚀性

采用电压-时间曲线、膜厚-时间曲线、X射线衍射法、扫描电镜、能量色散谱仪、X射线光电子能谱法、全浸腐蚀实验和极化曲线等方法分别研究了AZ91D铸镁合金阳极氧化成膜动力学过程、阳极氧化膜的表面形貌、结构、元素组成、元素价态以及相成分和膜层的耐蚀性.结果表明,在阳极氧化的4个阶段中,由于各个阶段所生成膜的厚度、结构和成分等均不同,因此膜的耐蚀性相差很大;镁合金阳极氧化时耐蚀性最好的膜层是在阳极氧化过程中的第阶段和第阶段的交界处所生成的膜层;镁合金阳极氧化膜中含有Mg,O,Si,B和少量的Al,Na元素,膜层主要由MgO,MgSiO₃和Mg3B2O6组成.     

阳极氧化法制备阀金属氧化物纳米管的机理及影响因素

阳极氧化法不仅能够简便地制备出阀金属氧化物纳米管,而且通过调节各种参数可以调控所制备纳米管的形貌.阳极氧化法制备的纳米管具有优异的化学/物理性能,在众多领域都得到了广泛应用.本文综述了阳极氧化法制备纳米管膜的基本过程以及三种常见的模型,并以三种具有代表性的阀金属(Al、Ti、Zr)为例,分别介绍了它们形成多孔膜反应过程和常用的制备过程,同时也介绍了其他阀金属及其合金的制备方案.最后,结合对Al、Ti、Zr的实验过程,讨论、分析了电压大小、电解液种类、电解液浓度、反应时间等控制因素对阳极氧化法制备纳米管膜形貌的影响,对制备形貌规整的多孔膜,提高多孔膜在实际应用中的性能具有一定的意义.     

环亚硫酸甘油酯衍生物作为电解液添加剂对锂离子电池电化学性能的影响

在亚硫酸酯基团的基础上引入苯环,设计并合成了3种环亚硫酸甘油酯衍生物[双(1,2-环亚硫酸甘油酯)对苯二甲酸酯、三(1,2-环亚硫酸甘油酯)均苯三甲酸酯和四(1,2-环亚硫酸甘油酯)均苯四甲酸酯],通过倍率充放电、恒流充放电、交流阻抗和扫描电子显微镜等测试研究了这些添加剂对锂离子电池性能的影响.结果表明,与空白电解液相比,加入三(1,2-环亚硫酸甘油酯)均苯三甲酸酯的电解液球化石墨电极表面可形成一层致密而稳定的固体电解质界面(SEI)膜,从而优化电极-电解液的界面性能,改善电池的倍率性能和循环性能,且在循环80周后电池阻抗增加较小;而双(1,2-环亚硫酸甘油酯)对苯二甲酸酯和四(1,2-环亚硫酸甘油酯)均苯四甲酸酯的加入不会明显改善电池的循环性能.研究结果表明苯环上亚硫酸甘油酯基团的数目对其性能影响较大.     

pH值对AZ31镁合金表面植酸转化膜在模拟体液耐腐蚀性能的影响

采用沉积的方法在镁合金AZ31表面制备植酸转化膜并研究了pH值的影响. 利用极化曲线和电化学阻抗谱方法测定其耐腐蚀性能,用扫描电子显微镜观察转化膜的表面微观结构,用能谱测定转化膜的组成元素. 在理论上通过热力学的方法分析最佳pH值. 植酸转化膜可以提高镁合金AZ31的耐腐蚀性能. 当植酸溶液的pH=5时腐蚀效率达到了89.19%,此时腐蚀电位正移了156 mV,腐蚀电流密度与没有处理的试样相比减小了约一个数量级. 热力学分析表明植酸转化膜的耐腐蚀性能不仅受植酸根离子和镁离子浓度的影响,也与氢气释放的速率有关.     

具有阳极氧化膜的镁合金电极性能的研究

镁合金电极上生成阳极氧化膜的保护技术，使电极耐大气腐蚀的性能大大优于用铬酸盐膜保护的镁电极。阳极氧化工艺条件不同。镁电极的耐腐蚀性和电压滞后性能不同，本文讨论了膜的组成，形态，厚度等对性能的影响。     

LiBOB基电解液成膜性及其循环性能

通过循环伏安(CV)、电化学阻抗谱(EIS)、扫描电子显微镜(SEM)、X射线光电子能谱(XPS)和傅立叶变换红外(FTIR)光谱研究了双乙二酸硼酸锂(LiBOB)基电解液在石墨表面的成膜性及其在常温(25 ℃)和高温(70 ℃)下对石墨循环性能的影响. 结果表明, LiBOB基电解液的成膜电位在1.7 V, 其中BOB-离子还原形成的草酸盐是固体电解质相界面(SEI)膜的有效成分之一. 电化学阻抗谱显示, 膜阻抗在循环过程中呈现减小趋势, 这有利于提高循环稳定性. 在常温和高温条件下, 石墨在该电解液体系中均表现出优于其在LiPF6基电解液体系中的循环性能.     

电流密度对锌电积用Pb-Ag平板阳极电化学行为的影响(英文)

研究了在不同电流密度下进行长时间极化后Pb-Ag(0.8%(质量分数,w))平板阳极的阳极电位、腐蚀率及阳极钝化膜.同时,也研究了该阳极在ZnSO4-MnSO4-H2SO4电解液中的阴极电流效率和阴极锌品质.阳极钝化膜的表面形貌用扫描电镜(SEM)进行观测.实验结果表明,不管电解液中是否存在Mn2+,电流密度对阳极和阴极的电化学行为都产生了显著的影响.随着电流密度的升高,阳极电位、腐蚀率、阴极电流效率和阳极泥生成量也增加,而阴极锌中的Pb含量则减少.当电流密度从500A·m-2降到200A·m-2时,阳极在ZnSO4-MnSO4-H2SO4电解液中的稳定电位和腐蚀率分别减少64mV和40%.此外,在比较低的电流密度下,阳极电位更容易稳定,阳极表面生成的钝化膜更加致密并与基体结合牢固,这些都有利于降低阳极腐蚀率.为了降低阳极电位、减小阳极腐蚀率及阳极泥生成量并提高阴极电流效率和阳极锌品质,锌电积的理想工作条件是较低的阳极电流密度和较高的阴极电流密度.     

稀土盐对铝合金阳极化过程的影响

在阳极化溶液中添加稀土盐得到的铝合金氧化膜在腐蚀试验中表现出优良的耐蚀性能,现场椭圆法对阳极氧化过程的研究结果表明,稀土盐的加入,对椭圆编振参数的振荡方式没有显著影响,但却使振荡的周期和振幅发生了一些变化,由此可以推知,稀土盐的加入并未改变氧化膜的组成,但却在一定程度上影响了成膜过程,使膜的结构发生了变化。对椭圆数据进行定量分析的结果进一步表明：加入稀土盐后,氧化膜多孔层生长速率加快,阻挡层厚度增加,多孔部分变得更加致密,这种结构上的变化是阳极化膜耐蚀性能得以提高的主要原因,EDAX和TEM分析结果也证实了椭圆法研究的结果。     

Study on microarc oxidation of AZ31B magnesium alloy in alkaline metal silicate solution

The effects of pulsating current and voltage sources with different magnitudes on an oxide film formed by microarc oxidation (MAO) of AZ31B magnesium alloy in alkaline metal silicate solution were investigated. The thickness of an oxide film increased with increasing current source but the uniformity of the surface of an oxide film became worse. The unstable oxidation process represented by fluctuating voltage established across an oxide film was discussed and related to the surface roughness and the melting down of magnesium alloy. By comparing the surface of an oxide film a pulsating current source produced more uniform oxide film on magnesium alloy than a pulsating voltage source.     

A zirconia-polyester glycol coating on differently pretreated AISI 316L stainless steel: corrosion behavior in chloride solution

The effect of zirconia and zirconia-polyester glycol hybrid coatings on the corrosion resistance of mechanically polished or anodized AISI 316 stainless steel (316L), was studied by potentiodynamic polarization and electrochemical impedance spectroscopy in 0.1 M NaCl and scanning electron microscope and atomic force microscopy examinations. The deposition of zirconia coatings was achieved by the sol–gel technique by immersing the samples in either the inorganic polymer or the organic–inorganic polymer mixture. From potentiodynamic and impedance measurements, the grade of protection is reduced with the exposure time to the electrolyte, which is mainly associated with lost of film adhesion and, consequently, detachment from the metal substrate. However, the uncoated anodized sample revealed an unexpected corrosion behavior; the anodic film formed during anodizing readily increased the corrosion resistance of the 316L stainless steel in 0.1 M NaCl, revealing a considerable reduction in the corrosion current density and an increase in the pitting potential.     

Anodizing parameters optimization of Ti–6Al–4V titanium alloy using response surface methodology

The present paper depicts application of response surface methodology (RSM) for optimizing the anodizing parameters of Ti–6Al–4V (TA6V) titanium alloy. Three operating parameters, i.e., voltage (V), temperature (T) and time (t), are designed as factors by using RSM design. Reliable regression models were established between the input parameters and the given responses, namely oxide thickness (e), Vickers hardness (Hv) and polarization resistance (R_p) with regression coefficients multiples of 0.940, 0.925, 0.865, respectively, indicating good agreement between the experimental values and those predicted using the quadratic model.The predicted values of V (42.67 V), t (45.9 min) and T (29.5 °C) are the optimal anodization combination leading to a TiO₂ layer with the best compromise between the oxide thickness (28.7 μm), Vickers hardness (321.90) and bias resistance (6.37 MΩ cm²). It was observed that the hardness characteristic is more affected by anodizing time and temperature, and less sensitive to voltage and parameter interactions. Polarization resistance is strongly influenced by voltage, modestly influenced by anodizing time and temperature, and less sensitive to parameter interactions. Moreover, higher anodizing parameters lead to higher thickness. Therefore, RMS could be a suitable method to optimize anodizing parameters of titanium alloys.     

A tracer investigation of chromic acid anodizing of aluminium

A tungsten tracer introduced into a sputtering‐deposited aluminium substrate was employed to investigate pore development in anodic films formed at 3 mA cm^?2 in 0.25 M chromic acid electrolyte at 313 K. The anodized specimens were observed by transmission electron microscopy (TEM), with compositions of films determined by Rutherford backscattering spectroscopy (RBS). The anodic films were found to be similar in thickness to that of the aluminium layer consumed during anodizing and revealed the feathered pore morphology that is a characteristic of the electrolyte. The anodizing efficiency was ～45–48%, with tungsten tracer species, in addition to aluminium species, being lost to the electrolyte at the pore base. These findings, together with the relatively uniform distribution of tungsten species within the film, are consistent with field‐assisted dissolution of the alumina playing a major role in the development of pores. The films contrast with those formed in phosphoric and sulphuric acid electrolytes, for which feathering of pores is absent, the tracer distribution is inverted and the film thickness exceeds that of the consumed metal, features indicative of the influence of material flow in pore development. Copyright © 2007 John Wiley & Sons, Ltd.     

Film characteristics of anodic oxidized AZ91D magnesium alloy by applied power

This study examined the film characteristics of an anodized AZ91D magnesium alloy by varying the direct current and pulse frequency conditions. In order to evaluate the effect of the pulse frequency on film formation, anodic oxidation was carried out by applying direct current and pulse current at a current density of 300 mA/cm². Compared with the sample groups treated with the direct current, a large number of small arcs were generated continuously on the film treated with the pulse current and the film formation rate was found to increase. Homogeneous and compact pores were formed with increasing frequency, and the rate of formation was increased rapidly to the arrival voltage. The film thickness increased and the surface roughness decreased with increasing anodic oxidation time at a fixed frequency of 125 Hz. However, treatment for more than 3 min led to decomposition of the oxidized film onto the previously formed film, which caused an increase in the number of cracks and pores within the film. The most uniform and smallest pores were acquired when the surface was anodized for 3 min at a current density and frequency of 300 mA/cm² and 125 Hz, respectively. X‐ray diffraction revealed the formation of MgO and Mg₂SiO₄ peaks, with a relative decrease in peak intensity for the MgO and Mg substrate. The Vickers hardness value was higher on the treated groups than on the untreated group, and the potentiodynamic polarization test revealed satisfactory corrosion resistance through a decrease in corrosion density and a large improvement in the corrosion potential. Copyright © 2009 John Wiley & Sons, Ltd.     

添加氧化铈对AZ91D镁合金表面富镁涂层的保护作用

通过Machu测试、电化学交流阻抗(EIS)和扫描电子显微镜(SEM)等方法研究了添加氧化铈对AZ91D镁合金表面富镁涂层防护性能的影响.氧化铈添加量较少(0.1%,w)时,对涂层耐蚀性无影响;添加量过多(3%)时,涂层耐蚀性降低;添加氧化铈颗粒为0.5%时,涂层的阻抗增大,涂层电容降低,对AZ91D镁合金基体的保护性能明显提高.尽管添加氧化铈不改变富镁涂层对AZ91D镁合金的保护机制,但可显著延长涂层的服役寿命.氧化铈能够降低纯镁颗粒的电化学反应活性,使镁粉腐蚀速率降低,阴极保护时间延长.添加一定量氧化铈后,也有利于涂层屏蔽性能提高,氧化铈能降低AZ91D镁合金表面阳极腐蚀电流密度,提高镁合金腐蚀电位,从而有利于富镁涂层发挥对镁合金基体的阴极保护作用.     

铈、锂盐对铝阳极氧化膜的协同封闭作用

研究了铈、锂盐在铝阳极氧化膜封闭处理中的协同作用.场发射扫描电镜和X射线衍射谱对铈、锂盐协同封闭前后铝阳极氧化膜形貌和结构的研究结果表明，封闭后膜表面的孔洞消失，封闭产物分布均匀，封闭后膜仍然以非晶态形式存在.根据X射线光电子能谱的结果，封闭后的膜主要由含结晶水的Al2O3及铈、锂的混合氢氧化物组成，同时膜中还含有及封闭溶液组分中的一些阴离子.电化学阻抗谱的研究结果表明铈、锂盐协同封闭能够显著提高膜的耐蚀性能.在实验结果基础上，初步认为铈、锂盐封闭是通过生成结构紧密的封闭产物填充、覆盖膜孔，从而显著提高铝阳极氧化膜的耐蚀性能.