用于X射线诊断的晶体布喇格成像系统

为了评估惯性约束聚变实验中激光辐射驱动的对称性和均匀性,分析靶丸的运动过程,设计一种新型诊断单色X射线的弯曲晶体布喇格成像系统,该系统核心部件由色散元件球面弯曲晶体和探测装置组成.利用光线追踪软件对该成像系统进行模拟验证,并搭建了晶体布喇格成像系统进行X射线背光成像测试实验.实验获得了清晰的Cr靶单色X射线背光二维网格信息,石英球面晶体布喇格成像系统空间分辨率为83μm,表明该成像系统可以用于等离子体X射线的背光成像诊断.     

植物研究用γ射线成像系统设计

为了利用正电子发射断层成像技术在植物生理功能研究中的优势,正在开发由两个探测器相向放置构成的γ射线成像系统.系统中采用的探测器是由10×10的氧正硅酸镥(LSO)晶体阵列与滨松R5900-C12耦合组成.单个LSO尺寸为1.8mm×1.8mm×10mm.根据PET应用的特点,测试了该探测器的性能.所有闪烁晶体的图像在位置图谱中清楚可见;511keV全能峰处的能量分辨率位于14.5%—22%之间;符合时间分辨率随着位置灵敏光电倍增管的供给电压的增加而得到改善.这些实验结果表明,该LSO探测器适于构造高分辨率的双探测器成像系统.     

植物研究用γ射线成像系统设计（英文）

为了利用正电子发射断层成像技术在植物生理功能研究中的优势,正在开发由两个探测器相向放置构成的γ射线成像系统.系统中采用的探测器是由10×10的氧正硅酸镥(LSO)晶体阵列与滨松R5900-C12耦合组成.单个LSO尺寸为1.8mm×1.8mm×10mm.根据PET应的特点,测试了该探测器的性能.所有闪烁晶体的图像在位置图谱中清楚可见;511keV全能峰处的能量分辨率位于14.5%-22%之间;符合时间分辨率随着位置灵敏光电倍增管的供给电压的增加而得到改善.这些实验结果表明,该LSO探测器适于构造高分辨率的双探测器成像系统.     

条纹激光扫描水下成像系统中像面照度特性的研究

条纹激光扫描成像方法能够同时满足水下激光成像系统对增大视场和减小后向散射光影响的要求.对条纹激光扫描成像系统中的像面照度特性进行了理论和实验研究,推导出了目标反射光照度和后向散射光照度的计算式,分析了图像对比度与成像距离间的关系,并进行了极限成像距离的水下实验.实验结果表明该套成像系统的极限成像距离均为2个衰减长度.     

高衍射效率衍射望远镜系统的设计/加工及成像性能测试

为提高衍射效率,设计并制作了口径为300mm的衍射成像系统.该系统的物镜是由一块四台阶位相型菲涅尔波带片通过激光直写套刻和Ar离子束物理刻蚀技术在石英玻璃基板上加工而成.测试了衍射物镜的衍射效率,实验结果表明:衍射物镜在波长632.8nm处的衍射效率为66.4%,达到理论值的82%.搭建了衍射成像系统光路,分别采用10μm星点孔与分辨率板,测试了系统的成像性能.实验测得星点像直径为44μm,分辨率板的极限分辨率达到84lp/mm,接近该系统的理论计算值,表明该衍射成像系统具有较好的成像性能.     

非共轴四通道偏振成像方法研究

针对当前偏振成像方法的实时性不好、能量利用率低以及分辨率不高等问题，提出了一种非共轴四通道偏振成像方法。该方法通过4个通道采集不同偏振方向的图像来融合计算偏振度图像。数值仿真分析了影响系统偏振成像结果的通道间距、通道平行度和偏振片检偏角度误差，得出了满足偏振成像精度达到1%的系统参数容限。在实验研究方面，研制出了非共轴四通道的偏振成像系统，并对室外距离约为50 m的车辆进行了实验。实验证明了该系统可以有效地对目标进行偏振成像。     

红外时间延迟积分点目标探测系统中速度失配影响研究

基于时间延迟积分的红外点目标探测系统在推扫成像过程中会受到速度失配的影响导致点目标的探测性能降低.基于调制传递函数的传统频域建模分析方法由于缺少相位传递函数的介入,无法对目标探测性能的影响进行有效分析.为了解决该问题,采用成像系统的点扩散函数以及线扩展函数建立了成像系统的速度失配模型,并对速度失配对目标检测系统的影响进行了研究.模型理论计算以及实际成像实验结果表明,当时间延迟积分级数为8级,速度失配量ΔV/V=25%时,点目标能量响应均值下降50%,当速度失配达到ΔV/V=12.5%时,点目标能量响应均值下降30%.研究结果可为后续红外时间延迟积分成像系统的设计提供参考.     

基于合成孔径技术的内镜超声相控阵成像算法

利用孔径大小为2.32mm的16阵元换能器,搭建了一套16通道的内镜超声相控阵成像实验系统。在此基础上提出了一种适用于内镜成像的相控阵成像算法(PAI),该算法利用延时和叠加算法(DAS)取得扫描线数据,再利用合成孔径技术中的相干样点叠加,得到高分辨率图像。该相控阵成像算法实现了发射和接收的动态聚焦。经FieldII仿真和内镜探头超声成像实验验证,与延时和叠加算法以及动态接收聚焦算法(DRF)相比,图像的理论横向分辨率分别提高了93.68%和17.5%,实验获得的实际横向分辨率分别提高了92.78%和14.69%,验证了相控阵成像算法和实验系统的可行性。     

连续波CO2相干激光成像研究

本文描述一台演示性连续波CO_2相干激光成像系统,报道了单、双点源目标的相干成像实验结果,并对影响成像质量的一些因素进行了讨论.该系统稍加改进即可用于速度与三维距离成像.     

自适应多光谱光声成像技术研究

光声成像技术是利用激光照射组织产生超声波成像的新型医学影像技术.在传统光声成像中,由于组织体内复杂的成分与环境会对入射光波产生较大的扰动而导致波前畸变、图像分辨率下降,从而降低诊断的准确性.为了克服这一影响,本文提出了一种自适应多光谱光声成像技术.该技术利用自适应光学技术可有效地降低组织对光波扰动的影响,提高系统成像分辨率与图像对比度.此外,该系统还融合了多光谱成像技术,可在多种波长下对目标成像,从而更好地进行组织结构识别、组分分析等.实验结果表明,该系统十分适用于复杂的生物组织光声成像,可极大地增强光声成像性能,在生物医学领域具有广阔的应用前景.     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Hybrid Wavelength and Code Division Multiple Access in Optical Networks

A review of schemes for multiple access in fiber optic networks shows that a hybrid of wavelength and code division multiple access (WCDMA) combines the best features of both. In particular, the hybrid scheme retains the large information carrying capacity of wavelength division multiple access (WDMA) and flexibility of code division multiple access (CDMA). In this paper WDMA, optical CDMA (OCDMA), and WCDMA networks are discussed. In OCDMA networks, concept of incoherent and coherent coding including inverse decoding and matched filter is introduced. The delay performance of both WDMA and WCDMA networks, under the simple suboptimum access protocols based on cyclic search, is computed. It has been shown quantitatively that tuning delay significantly affects the delay performance of both WDMA and WCDMA networks. Futhermore, delay performance of WCDMA networks is always better than the WDMA networks for the same tuning delay, load, and number of users.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.