不同衬底表面上大晶粒多晶Si薄膜的制备

利用高频感应加热化学气相沉积(HFCVD)工艺,以H2稀释的SiH4作为反应气体源,分别在n-(111)Si衬底上常规热生长的SiO2层、织构的SiO2层和纳米晶粒多晶Si薄膜表面上,制备了具有均匀分布的大晶粒多晶Si膜.采用扫描电子显微镜(SEM)和X射线衍射(XRD)等检测手段,测量和分析了沉积膜层的表面形貌、晶粒尺寸、密度分布与择优取向等结构特征.结果表明,多晶Si膜中Si晶粒的尺寸大小和密度分布不仅与衬底温度、SiH4浓度与反应气压等工艺参数有关,而且强烈依赖于衬底的表面状态.本实验获得的最好的薄膜中,Si晶粒平均尺寸约为2.3 μm,密度分布约为3.8×107/cm2.对薄膜的沉积机理分析表明,衬底表面上Si原子基团的吸附、迁移、成核与融合等热力学过程支配着大晶粒多晶Si膜的生长.     

纳米晶粒多晶Si薄膜的低压化学气相沉积

利用低压化学气相沉积(LPCVD)方法,以充Ar的SiH4作为反应气体源,在覆盖有热生长SiO2层的p-(100)Si衬底上制备了具有均匀分布的纳米晶粒多晶Si膜(nc-poly-Si).采用扫描电子显微镜(SEM)、原子力显微镜(AFM)和拉曼谱等检测手段,测量和分析了沉积膜层的表面形貌、晶粒尺寸与密度分布等结构特征.结果表明,nc-poly-v膜中Si晶粒的尺寸大小和密度分布强烈依赖于衬底温度、SiH4浓度与反应气压等工艺参数.典型实验条件下生长的Si纳米晶粒形状为半球状,晶粒尺寸约为40nm,密度分布约为4.0×1010cm-2和膜层厚度约为200nm.膜层的沉积机理分析指出,衬底表面上Si原子基团的吸附、迁移、成核与融合等热力学过程支配着nc-poly-Si膜的生长.     

Ge覆盖层诱导晶化多晶Si薄膜的晶化特性研究

采用电子束蒸发技术在衬底温度为180℃条件下生长具有Ge覆盖层的非晶Si薄膜,并于500℃、600℃、700℃真空退火5h.采用Raman散射、X射线衍射(XRD)、全自动数字式显微镜等对所制备薄膜的晶化特性进行研究.结果表明,Ge覆盖层具有诱导非晶Si薄膜晶化的作用,且随着退火温度的升高a-Si薄膜晶化越显著.具有Ge覆盖层非晶薄膜经500℃退火5h沿Si(400)方向开始晶化,对应晶粒尺寸约为4.9 nm.将退火温度升高到700℃时,非晶硅薄膜几乎全部晶化,晶化多晶Si薄膜在Si(400)方向表现出很强的择优取向特性,晶粒尺寸高达23.3μm.与相同条件下制备的无Ge覆盖层的非晶Si薄膜相比,晶化温度降低了300℃.     

衬底温度对电子束蒸发ZnS薄膜结构和光学特性的影响

采用电子束蒸发法在不同衬底温度下,150℃、200℃、250℃和300℃,制备了ZnS薄膜;用X射线衍射仪、原子力显微镜、膜厚仪和紫外-可见光-近红外分光光度计分别表征ZnS薄膜的晶体结构、表面形貌和光学特性;并分析了不同衬底温度对薄膜的结构和光学特性的影响.结果表明:在硅衬底上制备的ZnS都为多晶薄膜,具有闪锌矿β-ZnS结构;随衬底温度升高呈(111)晶面高度择优取向,平均晶粒尺寸有所增大,内应力、位错密度、折射率和吸收系数有所减小,禁带宽度随之增大;衬底温度为300℃时制备的薄膜表面均匀致密,呈现较优的结构和光学性能.     

衬底温度对共蒸发制备GaSb多晶薄膜性质的影响

采用共蒸发的方法在玻璃衬底上制备出GaSb多晶薄膜材料.研究了薄膜生长速率与衬底温度、Ga源温度和Sb源温度的关系.通过XRD、UV-Vis、Hall效应和AFM等测试方法,研究了衬底温度对于GaSb薄膜的结构特性、光电性质以及表面形貌的影响.GaSb多晶薄膜具有(111)择优取向,薄膜的吸收系数达到105 cm-1,晶粒尺寸随衬底温度升高逐渐增大;衬底温度为540℃时,薄膜的迁移率达到127 cm2/V·s,空穴浓度为3×1017 cm-3.GaSb薄膜的表面粗糙度随温度增加而增加.     

退火温度对La3Ga5SiO14薄膜结构及表面形貌的影响

采用脉冲激光沉积技术在Si(100)衬底上制备了La3Ga5SiO14薄膜,并研究了不同的退火温度对薄膜结构和表面形貌的影响.衬底温度为室温时生长的薄膜经过800 ℃以上的高温退火后,由最初的无定形态转变为无规则取向的多晶结构.衬底温度为400 ℃时生长的薄膜经过800 ℃退火处理后呈现无序的多晶形态.当退火温度进一步升高至1000 ℃时,XRD图谱显示薄膜由最初的(220)和(300)两个结晶方向转变为以(200)和(400)为主要取向的多晶结构.表面形貌分析表明:衬底温度为400 ℃时,随着退火温度的升高,薄膜颗粒尺寸逐渐增大,表面无裂纹,而衬底温度为室温时生长的薄膜退火后则出现大量的裂缝、孔洞等缺陷.     

掺硼纳米晶粒多晶Si薄膜的结构特征与电学特性

采用低压化学气相沉积(LPCVD)工艺,以SiH4作为反应气体源和B2H6作为硼(B)掺杂剂,在单晶Si或石英表面上,通过原位掺杂制备了掺B的纳米晶粒多晶Si(nc-poly-Si(B))薄膜.利用扫描电子显微镜(SEM)、原子力显微镜(AFM)和拉曼光谱等手段,检测和分析了沉积膜层的表面形貌、晶粒尺寸和密度分布等结构特征.结果表明,在典型工艺条件下,获得了晶粒尺寸为大约15 nm和密度分布为大约9 × 1010cm-2的nc-poly-Si(B)薄膜.样品经退火处理后,Si晶粒尺寸变大,排列更加有序,而且电导特性明显改善.利用常规四探针法测量了样品的薄层电阻.并讨论了B掺杂浓度和退火温度对薄膜电学性质的影响.     

退火升温速率对LaNiO3薄膜结构和电学性能的影响

采用溶胶-凝胶法在SiO2/Si(100)衬底上制备了镍酸镧(LaNiO3,LNO)薄膜,并利用XRD、SEM、AFM和半导体参数分析仪等研究了退火升温速率对LNO薄膜结构和电学性能的影响.结果表明,溶胶-凝胶法制备的LNO薄膜呈现赝立方钙钛矿型多晶结构,呈(110)择优取向生长;薄膜表面平整、均匀、无裂纹.随着退火升温速率的增加,LNO薄膜的晶粒尺寸先增大后减小;其电阻率先减小后增大.在退火升温速率为20℃/min时,LNO薄膜晶粒尺寸达到最大值94 nm,电阻率达到最小值9.5 x10-4 Ω·m.     

纯氮气反应溅射AlN薄膜及性质研究

在不同氮气浓度、不同溅射气压和衬底温度为20～370 ℃的条件下,分别在多种衬底上采用反应磁控溅射法沉积AlN薄膜.X射线衍射图谱表明:温度大于180 ℃时可在多种衬底上沉积出具有c轴择优取向的纤锌矿AlN薄膜.衬底温度和溅射时间的增加有利于薄膜结晶性的改善. 1.5 Pa的纯氮气气氛和Si(100)衬底是最佳择优生长条件.由紫外-可见光透射谱计算得到:在石英衬底上沉积的薄膜折射率为1.80～1.85,膜厚约为 1 μm、光学能隙为6.1 eV.原子力显微镜照片表明:在Si(100)衬底上制备的薄膜表面平滑,均方根粗糙度为2.2～13.2 nm.     

衬底温度对氧化锌薄膜微结构及光学性能的影响

衬底温度是磁控溅射法制备氧化锌薄膜中一个非常重要的工艺指标,探索衬底温度对氧化锌薄膜微结构及光学性能的影响对制备环保型高质量氧化锌紫外屏蔽材料具有重要意义。以质量分数99.99%的氧化锌陶瓷靶为溅射源,利用射频磁控溅射技术在石英衬底上沉积了氧化锌紫外屏蔽薄膜,通过X射线衍射仪、薄膜测厚仪、紫外-可见分光光度计、荧光分光光度计进行测试和表征,研究了不同衬底温度对ZnO薄膜微结构及光学性能的影响。实验结果表明:制备所得薄膜均为六角纤锌矿结构,具有沿(002)晶面择优取向生长的特点,其晶格常数、晶粒尺寸、透过率、光学能隙、可见荧光、结晶质量等都与衬底温度密切相关,当衬底温度为250 ℃,溅射功率160 W,氩气压强0.5 Pa,氩气流速8.3 mL/min,沉积时间60 min时,所得氧化锌薄膜样品取向性最好,晶粒尺寸最大,薄膜结构致密,具有良好的光学性能和结晶质量。     

Triethyl ammonium salt of O,O′-bis(p-tolyl)dithiophosphate, [Et3NH]+[(4-MeC6H4O)2PS2]−

Triethyl ammonium Salt of O,O′-bis(p-tolyl)dithiophosphate and O,O′-bis(m-tolyl)dithiophosphate have been obtained by reaction of p- and m-cresol, respectively with P₂S₅ in toluene and have been characterized by elemental analysis, IR, ¹H and ³¹P NMR spectroscopy. The molecular structure of O,O′-bis(p-tolyl)dithiophosphate has been determined. Crystal data: [Et₃NH]⁺[(4-MeC₆H₄O)₂PS₂]⁻: Monoclinic, P2₁/c, a=15.2441(9) ?, b=10.415(2) ?, c=3.9726(9) ?, β=91.709(7)°, V=2217.5(1) ?⁻³, Z=4.Supplementary materials Additional material available from the Cambridge Crystallographic Data Centre (CCDC no. 600927 for [Et₃NH]⁺[(4-MeC₆H₄O)₂PS₂]⁻ comprises the final atomic coordinates for all atoms, thermal parameters, and a complete listing of bond distances and angles. Copies of this information may be obtained free of charge on application to The Director, 12 Union Road, Cambridge CB2 2EZ, UK (fax: +44-1223-336033; email: deposit@ccdc.cam.ac.uk or www:http://www.ccdc.cam.ac.uk).     

First-principles coexistence simulations of supercooled liquid silicon

We perform first-principles coexistence simulations of the low-density and the high-density phases of supercooled liquid silicon and find a negative slope for the coexisting line in the temperature-pressure plane. Electron density maps and electron-localization function plots of the two phases of silicon show marked differences. The calculated differences suggest more localized electrons in the low-density liquid compared to the high-density liquid, coming from an increased population of covalent bonds, which further explain the calculated negative slope in the two phase coexistence regime. This is consistent with the presence of a pseudo-gap in low-density liquid silicon, absent in the high-density liquid which shows a metallic behavior.     

Crystal structures of thecis andtrans isomers of dithiahexahydro[3.3]metacyclophane

Structures of both thecis andtrans isomers of dithiahexahydro[3.3]metacyclophane, ?C₆H₄?CH₂SCH₂?C₆H₁₀?CH₂SCH₂?, have been determined, wherecis andtrans refer to the attachments to the cyclohexane ring. Thecis form crystallizes in the monoclinic space groupP2₁/c witha=8.4299(11)Å,b=21.772(2)Å,c=8.9724(13)Å, β=116.574(11)^o, andZ=4. Thetrans isomer packs into the monoclinic space groupP2₁ witha=8.159(16)Å,b=10.185(5)Å,c=9.558(2)Å, β=112.435(18)^o, andZ=2. The cyclohexane ring of thecis isomer is in the chair conformation, while the cyclohexane of thetrans isomer is found in a twisted boat conformation.     

CTAB与SDBS对碳酸锶粒子生长形态调控及机理研究

以表面活性剂CTAB和SDBS为化学添加剂,采用化学共沉淀法对碳酸锶晶体的生长形态进行调控,成功地制备出了实心的树枝状和花瓣为空心的花状碳酸锶粉体,并用X射线衍射(XRD)、扫描电子显微镜(SEM)和傅里叶变换红外光谱(FT-IR)等分析手段对样品进行了表征;最后重点对化学添加剂可能产生的影响机理进行了初步的探讨.结果表明,CTAB和SDBS在晶体生长的过程中能起到显著的影响作用,两者对粒子分散性能的作用效果相反,而且后者对晶体(013)和(213)晶面表面能降低的贡献明显大于前者.     

Crystal structure of Zn4Na(OH)6SO4Cl·6H2O

The structure of Zn₄Na(OH)₆SO₄Cl·6H₂O, a secondary mineral from Hettstedt, Germany, was determined by single-crystal X-ray diffraction. The crystals are hexagonal,a=8.413(8),c=13.095(24) Å, space group $P\bar 3$ , Z=2. The structure was refined to R=0.0554 and R_w=0.0903 for 970 reflections with I≥3σ(I). The structure can be described as zinc hydroxide layers perpendicular toc, from which sulfates and chlorides extend. The layers are held together by a system of hydrogen bonds involving hexaaquo Na⁺ ions which occupy the interlayer space.     

Synthesis and Crystal Structure of 5-[2-(6-bromonaphthalenyloxymethyl)]-3-(4-morpholinomethyl)-1,3,4-oxadiazole-2(3<Emphasis Type="Italic">H</Emphasis>)-thione

Abstract  The title compound, C₁₈H₁₈BrN₃O₃S, a derivative of 1,3,4-oxadiazole, crystallizes in the triclinic space group P-1 with unit cell parameters a = 6.8731(3), b = 8.9994(4), c = 15.7099(6) ?, α = 92.779(3)°, β = 130.575(3)°, γ = 107.868(4)°, Z = 2. The dihedral angle between the mean planes of the planar naphthyl and morpholine (chair) rings with the planar oxadiazol ring is 50.1(8) and 76.8(6)°, respectively. The planar naphthyl ring is twisted 52.2(5)° with the mean plane of the morpholine ring. A group of four intermolecular close contacts are observed between a bromine atom and hydrogen atoms from the closely packed naphthyl, morpholine and oxy–methyl groups in the unit cell. These molecular interactions in concert with an additional series of π–π stacking interactions that occur between the center of gravity of the two 6-membered rings of the naphthalene group influence the twist angles of each of these three groups. A MOPAC AM1 calculation of the conformation energy of the crystal structure [226.0128(9) kcal] compared to that of the minimum energy structure after geometry optimization [29.9744(1) kcal] reveals a significantly reduced value. The twist angles of the three groups above also change after the AM1 calculation giving support to the influence of both intermolecular C–H···Br short-range interactions and Cg π–π stacking interactions on these angles which therefore play a role in stabilizing crystal packing. Graphical Abstract  Crystal structure of 5-{[(6-bromonaphthalen-2-yl)oxy]methyl}-3-(morpholin-4-ylmethyl)-1,3,4-oxadiazole-2(3H)-thione, C₁₈H₁₈BrN₃O₃S, is reported and its geometric and packing parameters described and compared to a MOPAC computational calculation. Electronic supplementary material  The online version of this article (doi:) contains supplementary material, which is available to authorized users.     

Crystal structure of irisolidone from the flowers of Pueraia lobata

Irisolidone (5,7-dihydroxy-6,4′-dimethoxyisoflavone) was isolated from the flowers of Pueraia lobata and its crystal structure was examined by X-ray single crystal diffraction. The crystal structure of irisolidone is monoclinic, space group P2₁/c with a = 15.491(9) ?, b = 7.895(4) ?, c = 13.321(7) ?, β = 110.546(9)° and Z = 4. Hydrogen bonding and aromatic π–π stacking assemble the title compound into a three-dimensional networking structure.     

Synthesis of spinacine and spinacine derivatives: crystal and molecular structures of Nπ-hydroxymethyl spinacine and Nα-methyl spinaceamine

The natural amino acid L-Spinacine (4,5,6,7-tetrahydro-1H-imidazo[4,5-c]pyridine-6-carboxylic acid) has been synthesized following a new pathway which gives a chemically and optically pure product with an excellent yield. The crystal structures of a synthetic intermediate, N^π-hydroxymethyl-spinacine, and a spinacine derivative, N^α-methyl-spinaceamine, have been investigated through X-ray diffraction: Spi(πMeOH)·H₂O, monoclinicP2 _i,a=8.571(1),b=6.682(1),c=8.588(1) Å, and β=94.67(1)^o. Spm(αMe)·2HCl·H₂O, triclinicP l,a=7.492(4),b=10.799(3),c=7.040(2) Å, α=91.88(2), β=98.36(3) and γ=73.34(3)^o. Spi(πMeOH) crystallizes with a water molecule and displays a zwitterionic character. The carboxylate group is in equatorial position and forms a short electrostatic interaction of 2.618(2) Å between one of its oxygens and the protonated nitrogen of the tetrahydropyridine ring. The crystal packing is assured by strong O?H???O, O?H???N, N?H???N intermolecular hydrogen bonds and C?H???O close contacts. The biprotonated compounds Spm(αMe) crystallizes with two Cl^? anions and a water molecule. The positive charge on the imidazole ring is delocalized on the conjugated moiety N=C?N. The crystal is built up by clusters formed by two biprotonated Spm(αMe) molecules, four Cl^? anions and two water molecules linked together by hydrogen bonds.