研究简报聚苯乙烯接枝TiO2有机无机杂化超疏水涂层的制备

采用自由基聚合的方法,在经乙烯基三乙氧基硅烷(VTEOS)修饰的纳米TiO2表面上接枝聚苯乙烯(PS),而后制得PS-g-TiO2有机无机纳米杂化超疏水薄膜。利用场发射扫描电子显微镜和傅里叶变换红外光谱仪对PS-g-TiO2进行了形貌和结构表征,并探讨了VTEOS修饰对TiO2纳米粉体表面浸润性能的影响。测试结果表明,纳米TiO2经VTEOS改性后所制备的PS-g-TiO2薄膜和仅用硅烷偶联剂修饰的TiO2薄膜都具有良好的超疏水性能,水滴在薄膜上的最大静态接触角分别为160°和154°,滑动角分别为3°和4°。     

In situ synthesis and characterization of TiO<Subscript>2</Subscript> nanoarray films

Based on anodic aluminum oxide (AAO) templates prepared in different acidic solutions, highly ordered aligned titania nanotubes array films have been successfully prepared by the liquid phase deposition method. The effect of AAO template type on the microstructure of titania film have been studied. Using the template with a certain volume fraction of Al₂O₃ (less than 0.71), ordered aligned titania nanotubes were obtained, characterized with an outer diameter of 200 nm and an inner diameter of 100 nm, respectively. However, titania existed as ordered aligned nanorods with the diameter of 100 nm when the template with large volume fraction of Al₂O₃ (larger than 0.71) was used. TiO₂ thin films calcined at 400°C for 4 h have an anatase phase and exhibit good photocatalytic activity, i.e., 75% methylene blue could be degraded under ultraviolet irradiation for 2 h.     

Optically transparent superhydrophobic TEOS-derived silica films by surface silylation method

Optically transparent silica films were prepared at room temperature (~27°C) by keeping the molar ratio of TEOS:MeOH:H₂O (0.001 M NH₄F) constant at 1:19.29:6.20, respectively. A surface chemical modification of the films was done with alkylchlorosilanes at different concentrations from 0 to 1 vol. % and aging times varied from half to 2 h. The DMCS and TMCS surface modified silica films showed the static water contact angle of 146° and 162°, respectively. When the DMCS and TMCS modified films were cured at temperatures higher than 240 and 275°C, respectively, the films became superhydrophilic. Further, the humidity study was carried out at a relative humidity of 90% at 30°C temperature over 60 days. We characterized the water repellent silica films by Fourier transform infrared spectroscopy, scanning electron microscopy, atomic force microscopy, % of optical transmission, humidity tests and contact angle measurements.     

Photocatalytic degradation of Orange II by titania addition to sol–gel glasses

Glasses on SiO₂–CaO–ZnO–B₂O₃–K₂O–Al₂O₃ oxide system modified by addition of titania (0, 3, 5, 12, and 20% w) have been prepared by sol–gel method. The obtained gels were aged, dried and fired at 600 °C/1 h in order to stabilise the glass. The resulting fired powders were characterised by UV–Vis–NIR spectroscopy, scanning electron microscopy, transmission electron microscopy (TEM) and X-ray diffraction (XRD). Their photocatalytic capacity on the degradation of Orange II dye has been studied. The XRD and TEM studies indicate that system becomes amorphous with a nanostructured microstructure. From UV–Vis–NIR results the band gap calculated is around 3.5 eV for all modified glasses. Photoactivity of powders depends on amount of titania in glass composition and the specific surface area of prepared samples. The sample with highest surface area and lowest addition of titania (3% w sample) shows similar activity than commercial anatase used as reference.     

Tuning the wall thickness and pore orientation in mesoporous titania films prepared with low-temperature aging

Porous titania thin films with well-ordered mesostructures are prepared by using Pluronic surfactant P123 as the pore template and aging the films in a high-humidity environment at −6 °C. These structures are stable enough to undergo calcination at 400 °C to generate nanocrystalline TiO₂ walls with retention of mesoporosity. Under the aging conditions used, the films have well-ordered mesostructures even with a molar ratio of P123 to titanium (R) as small as 0.006. Because the P123 micelle diameter remains constant across a range of compositions, the pore diameter also remains fixed but the wall thickness of the titania thin films increases as the P123 concentration decreases without decreasing the long-range order of the products. Furthermore, mesoporous titania thin films with hexagonal close-packed channels oriented perpendicular to the substrate can be obtained R values of 0.008–0.012 by sandwiching the as-prepared films between glass slides modified with crosslinked P123. Analysis of the mesophases obtained here indicates that a transition from films containing significant 2D hexagonal channels to 3D hexagonal structure occurs below P123/Ti = 0.008. This does not match the expected volume fraction for this transition based on the mesophases behavior of aqueous P123 at room temperature, suggesting that a more detailed model would be needed to predict mesostructure in titania films aged below the freezing point of water.     

Sol–gel preparation and properties of hydroxypropylcellulose–titania hybrid thin films

Hydroxypropylcellulose (HPC)–titania hybrid thin films were prepared by sol–gel method where titanium tetraisopropoxide Ti(OC₃H₇ ⁱ )₄ was hydrolyzed under acidic conditions in the presence of HPC, followed by dip-coating and drying at 120 °C for 24 h. The viscosity average molecular weight of HPC was 55,000–70,000 or 110,000–150,000, and the TiO₂/(HPC + TiO₂) mass ratio ranged from 0 to 1, which was calculated on the assumption that all Ti(OC₃H₇ ⁱ )₄ is converted into TiO₂. The films were 0.35–1.0 μm thick, transparent in visible region and opaque in ultraviolet (UV) region, where the optical absorption coefficient in UV region increased with increasing titania content. The refractive index increased with increasing titania content, ranging from 1.6 to 1.8 for the hybrid thin films. The pencil hardness increased from 6B to 5H, the durability in hot water significantly increased and the contact angle of water on films increased from 35° to 89° with increasing titania content. Crack-free films could be deposited on organic polymer substrates irrespective of titania or HPC contents, where cracking did not occur at higher HPC contents even when the substrate was bent.     

Microstructure,dielectric properties and optical band gap control on the photoluminescence behavior of Ba[Zr<Subscript>0.25</Subscript>Ti<Subscript>0.75</Subscript>]O<Subscript>3</Subscript> thin films

Ba[Zr_0.25Ti_0.75]O₃ (BZT) thin films were synthesized by the complex polymerization method and heat treated at 400 °C for different times and at 700 °C for 2 h. These thin films were analyzed by X-ray diffraction (XRD), Fourier-transform infrared (FT-IR) spectroscopy, field emission gun-scanning electron microscopy (FEG-SEM) and atomic force microscopy (AFM), Ultraviolet–visible (UV–vis) absorption spectroscopy, electrical and photoluminescence (PL) measurements. FEG-SEM and AFM micrographs showed that the microstructure and thickness of BZT thin films can be influenced by the processing times. Dielectric constant and dielectric loss of BZT thin films heat treated at 700 °C were approximately 148 and 0.08 at 1 MHz, respectively. UV–vis absorption spectra suggested the presence of intermediary energy levels (shallow and deep holes) within the band gap of BZT thin films. PL behavior was explained through the optical band gap values associated to the visible light emission components.     

Effect of silver incorporation on crystallization and microstructural properties of sol–gel derived titania thin films on glass

Titanium dioxide (TiO₂) thin films, with and without silver (Ag), were prepared on float glass via sol–gel processing. The float glass substrates were pre-coated with a silica-barrier layer prior to the deposition of TiO₂-based thin films. Silver nanoparticle incorporation into the TiO₂ matrix was achieved by thermal reduction of Ag ions dissolved in a titanium-n-butoxide (Ti[O(CH₂)₃CH₃]₄) based sol during calcination in air at 250, 450 and 650 °C. Thin films were characterized using glancing incidence X-ray diffraction, UV–visible spectroscopy, X-ray photoelectron spectroscopy, and Raman spectroscopy. The effects of Ag concentration and calcination temperature on microstructure and on chemical and physical properties of the thin films have been reported. The size and chemical state of Ag particles, as well as the phase characteristics of the titania matrix were strongly influenced by Ag concentration and calcination temperature. Results from this study can be utilized in both processing and structure-functional property optimization of sol–gel based Ag-TiO₂ thin films by aqueous routes.     

Performance evaluation of the different nano-enhanced polysulfone membranes via membrane distillation for produced water desalination in Sert Basin-Libya

A Polysulfone-Polyethylene glycol (PS/PEG) flat sheet membrane was prepared by phase inversion technique. Dimethyl Formamide (DMF) was utilized as a solvent and deionized water was utilized as the coagulant. Polyethylene glycol (PEG) of a various dose of PEG 2000 was utilized as the polymeric improvers and as a pore-forming agent in the casting mixture. The single-walled carbon nanotube (SWCNTs), multi-walled carbon nanotube (MWCNTs), aluminum oxide (Al₂O₃) and copper oxide (CuO) nanoparticles (NPs) were utilized to improve the PS/PEG membrane performances. The characterizations of the neat PS, PS/PEG, PS/PEG/Al2O3 (M1) PS-PEG/CuO (M2), PS-PEG/SWCNTs (M3) and PS/PEG/MWCNTs (M14) nanocomposite (NC) modified membranes were acquired via Fourier-transform infrared analysis (FTIR), water contact angle estimation (WCA), scanning electron microscope (SEM), dynamic mechanical analyzer (DMA) and thermogravimetric analysis (TGA). Enhanced Direct contact membrane distillation (EDCMD) unit was used for estimating the efficiency of the performance of the synthesized NC membranes via 60 °C feed synthetic water and/or saline oil field produced water samples containing salinities 123,14 mg/L. Adjusting the operational procedures and water characteristics confirmed a high salt rejection of 99.99% by the synthesized NC membranes. The maximum permeate flux achieved in the order of SWCNTs (20.91) > Al₂O₃ (19.92) > CuO (18.92) > MWCNT (18.20) (L/m².h) with adjusted concentration of 0.5, 0.75, 0.75, 0.1 wt% compared with PS weight, i.e. 16%. The optimum operational circumstances comprised feed and permeate temperatures 60 °C and 20 °C, respectively. The achieved flux was 5.97 L/m².h, using brine oil field produced water, via PS/PEG/SWCNTs membrane with 0.5 wt% of SWCNTs. Moreover, the membrane indicated sustaining performance stability in the 480 min continuous desalination testing, showing that the synthesized PS/PEG/SWCNTs NC modified membrane may be of magnificent potential to be activated in EDCMD procedure for water desalination.     

Sol–gel titania coating on NiTi alloy with a porous titania film as interlayer

Porous titania film is prepared by alkali treatment of NiTi alloy followed by soaking treatment in HCl solution. The benefit of this porous titania film as an interlayer to improve adhesion and integrity of the sol–gel titania coating on NiTi alloy substrate is evidenced by surface morphological observations. X-ray diffraction analyses indicate the formation of Ni₄Ti₃ phase in the matrix during heat treatment of the NiTi samples. X-ray photoelectron spectroscopy results indicate that the titania coating with two dip-coating layers has completely covered the NaOH–HCl treated NiTi substrate, and potentiodynamic polarization tests show that this titania coating provides good protection for the treated NiTi substrate in 0.9% NaCl solution. Ultraviolet illumination can increase surface hydrophilicity of the NiTi samples by reducing contact angles from 60–80° to 20–10°.     

Cu-particle-dispersed (K<Subscript>0.5</Subscript>Na<Subscript>0.5</Subscript>)NbO<Subscript>3</Subscript> composite thin films derived from sol–gel processing

Sol–gel processing of Cu-particle-dispersed (K_0.5Na_0.5)NbO₃ (Cu/KNN) thin films was studied in an attempt to develop a method producing piezoelectric composite films with good mechanical performance. The Cu/KNN films were prepared via crystallization annealing at 650–750 °C for 1 min in air, followed by reduction annealing at 400–500 °C for 1–2 h in a 5% H₂ and 95% Ar gas mixture. The resultant composite films consisted of perovskite KNN, metallic Cu, and Cu₄O₃. This suggests that the decomposition of Cu sources takes two different ways in this study. The Cu/KNN composite films containing Cu₄O₃ phases were produced by the crystallization annealing at 700 °C for 1 min followed by the reduction annealing at 500 °C for 1 h. Surface morphology observations reveal that these films have dense KNN matrix with a grain size of ~200 nm and uniformly dispersed Cu or Cu₄O₃ particles with a size of <500 nm.     

Polystyrene‐b‐poly(2,2,2‐trifluoroethyl acrylate)‐b‐polystyrene copolymers: Synthesis and fabrication of their hydrophobic porous films,spheres, and fibers

New block copolymers Polystyrene‐b‐poly (2,2,2‐trifluoroethyl acrylate)‐b‐Polystyrene (PS‐PTFEA‐PS) with controlled molecular weight (M_n=5000‐11000 g?mol^?1) and narrow molecular weight distribution (M_w/M_n=1.13‐1.17) were synthesized via RAFT polymerization. The molecular structure and component of PS‐PTFEA‐PS block copolymers were characterized through ¹H NMR, ¹⁹F NMR, GPC, FT‐IR and elemental analysis. The porous films of such copolymers with average pore size of 0.80‐1.34 μm and good regularity were fabricated via a static breath‐figure (BF) process. The effects of solvent, temperature, and polymer concentration on the surface morphology of such film were investigated. In addition, microstructured spheres and fibers of such block copolymers were fabricated by electrospinning process and observed by scanning electron microscopy (SEM). Furthermore, the hydrophobicity of porous films, spheres, and fibers was investigated. The porous film showed a good hydrophobicity with the water‐droplet contact angles of 129°, and the fibers showed higher hydrophobicity with the water‐droplet contact angles of 142°. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 678–685     

Sol–gel elaboration and structural investigations of Lu<Subscript>2</Subscript>O<Subscript>3</Subscript>:Eu<Superscript>3+</Superscript> planar waveguides

Europium actived Lu₂O₃ sol–gel transparent and crack free films were deposited by dipping on silica substrates. The film microstructure was studied by waveguide Raman spectroscopy (WRS) with annealing temperatures from 400 up to 1,000 °C and X-ray diffraction. The WRS results and TEM observations were correlated and showed that crystallization of the lutetium oxide phase into cubic phase occurs at 600 °C and is stable up to 1,000 °C, the crystallite size increasing between ±38 nm with annealing temperature ranging from 600 to 1,000 °C. Opto-geometrical parameters were determined by m-lines spectroscopy using four different wavelengths of laser sources in order to confirm the step-index profile of the as-prepared waveguides. The Eu³⁺ doped films heat-treated at 1,000 °C presented a constant thickness for the wavelengths 493, 543, 594 and 632.8 nm and a density of 8.4 g cm⁻³. High-resolution X-ray images were obtained.     

Sol–gel synthesis and characterization of polycrystalline GdFeO<Subscript>3</Subscript> and Gd<Subscript>3</Subscript>Fe<Subscript>5</Subscript>O<Subscript>12</Subscript> thin films

Thin films of the perovskite and garnet structured gadolinium ferrites GdFeO₃ and Gd₃Fe₅O₁₂ have been synthesized by a sol–gel method, based on stoichiometric mixtures of acetyl acetone chelated Gd³⁺ and Fe³⁺ dissolved in 2-methoxy ethanol. After spin coating onto Si wafers, and heating in air at 700 °C for 20 h, neatly grown essentially single phase films were obtained. From X-ray photoelectron spectroscopy an iron deficiency is observed in the uppermost layer of both films, implying that the crystallites preferably end in planes rich in Gd and O but not in Fe. The films were also characterized by X-ray powder diffraction, scanning electron microscopy, infrared spectroscopy, and magnetic measurements.     

Synthesis of Cu2Mo6S8 powders and thin films from intermediate oxides prepared by polymeric precursor method

Powders and thin films of the copper molybdenum sulfide Cu₂Mo₆S₈ were synthesized from intermediate oxides prepared by polymeric precursor method based on Pechini process. In the case of the thin films, deposition was performed onto R-plane sapphire single crystal by spin coating. The influence of temperature and duration of the 3 step heat treatment cycle (calcination, sulfurization and reduction) were investigated to optimize the synthesis conditions. The first step of calcination under air atmosphere performed for 3 h at 450 °C and 400 °C is suitable to obtain the intermediate oxides powders and thin films, respectively. The sulfurization treatment at 600 °C for 2 h under H₂S/H₂ gas flow followed by reduction at 650 °C for 4 h under H₂ gas flow allowed to obtain Cu₂Mo₆S₈ in powder or thin film form. In the last case, a multilayer process led to dense and homogeneous films. Moreover, the insertion and superconducting behaviour of the final powders allowed to validate the Cu₂Mo₆S₈ synthesis by this moderate temperature process.     

Sol–gel synthesis of mesoporous WO3–TiO2 composite thin films for photochromic devices

Mesoporous WO₃–TiO₂ composite films were prepared by a sol gel based two stage dip coating method and subsequent annealing at 450, 500 and 600 °C. An organically modified silicate based templating strategy was adopted in order to obtain a mesoporous structure. The composite films were prepared on ITO coated glass substrates. The porosity, morphology, and microstructures of the resultant products were characterized by scanning electron microscopy, N₂ adsorption–desorption measurements, μ-Raman spectroscopy and X-ray diffraction. Calcination of the films at 450, and 500 °C resulted in mixed hexagonal (h) plus monoclinic phases, and pure monoclinic (m) phase of WO₃, respectively. The degree of crystallization of TiO₂ present in these composite films was not evident. The composite films annealed at 600 °C, however, consist of orthorhombic (o) WO₃ and anatase TiO₂. It was found that the o-WO₃ phase was stabilized by nanocrystalline anatase TiO₂. The thus obtained mesoporous WO₃–TiO₂ composite films were dye sensitized and applied for the construction of photochromic devices. The device constructed using dye sensitized WO₃–TiO₂ composite layer heat treated at 600 °C showed an optical modulation of 51 % in the NIR region, whereas the devices based on the composite layers heat treated at 450, and 500 °C showed only a moderate optical modulation of 24.9, and 38 %, respectively. This remarkable difference in the transmittance response is attributed to nanocrystalline anatase TiO₂ embedded in the orthorhombic WO₃ matrix of the WO₃–TiO₂ composite layer annealed at 600 °C.     

Preparation and characterization of 5,10,15,20‐tetraphenylporphyrin Langmuir films for gas chemsensor applications

In this work is reported the preparation and characterization of 5,10,15,20‐tetraphenylporphyrin (H₂TPP) films at the water‐air interfaces. The surface pressure‐area isotherms (π‐A) and UV‐Vis spectroscopy were used to investigate the effect of the spreading methods and parameters on the porphyrin monolayer formation. Also, Langmuir‐Blodgett (LB) and Langmuir‐Schaefer (LS) films were deposited onto glass substrates in order to study the conformation changes in porphyrin molecular packing. Quartz crystal microbalance (QCM) was utilized as the active solid substrate for the development of the NO₂ gas sensor based on the H₂TPP molecular films. The results of π‐A curves have clearly shown the significant contribution of the preparation methods and processing parameters on the conformation of porphyrin molecular films. The UV‐Vis spectroscopy results using polarized absorption dichroism have indicated different molecular packing for porphyrin films deposited by LB and LS methods, with relative tilted angles of 50° ± 5° and 35° ± 5°, respectively. Moreover, the QCM response has given strong evidence that H₂TPP porphyrin molecular films have performed as NO₂ chemsensor. Copyright © 2011 John Wiley & Sons, Ltd.     

Erratum to: Sol–gel synthesis of mesoporous WO3–TiO2 composite thin films for photochromic devices

Mesoporous WO₃–TiO₂ composite films were prepared by a sol gel based two stage dip coating method and subsequent annealing at 450, 500 and 600 °C. An organically modified silicate based templating strategy was adopted in order to obtain a mesoporous structure. The composite films were prepared on ITO coated glass substrates. The porosity, morphology, and microstructures of the resultant products were characterized by scanning electron microscopy, N₂ adsorption–desorption measurements, μ-Raman spectroscopy and X-ray diffraction. Calcination of the films at 450, and 500 °C resulted in mixed hexagonal (h) plus monoclinic phases, and pure monoclinic (m) phase of WO₃, respectively. The degree of crystallization of TiO₂ present in these composite films was not evident. The composite films annealed at 600 °C, however, consist of orthorhombic (o) WO₃ and anatase TiO₂. It was found that the o-WO₃ phase was stabilized by nanocrystalline anatase TiO₂. The thus obtained mesoporous WO₃–TiO₂ composite films were dye sensitized and applied for the construction of photochromic devices. The device constructed using dye sensitized WO₃–TiO₂ composite layer heat treated at 600 °C showed an optical modulation of 51 % in the NIR region, whereas the devices based on the composite layers heat treated at 450, and 500 °C showed only a moderate optical modulation of 24.9, and 38 %, respectively. This remarkable difference in the transmittance response is attributed to nanocrystalline anatase TiO₂ embedded in the orthorhombic WO₃ matrix of the WO₃–TiO₂ composite layer annealed at 600 °C.     

Phase separation of polymer‐functionalized SWNTs within a PMMA/polystyrene blend

Phase separation of polystyrene (PS) and poly(methyl methacrylate) (PMMA) blends was used as a means to segregate PS‐ or PMMA‐functionalized single‐walled carbon nanotubes (SWNTs) in thin films. Dilute solutions (5 wt % in THF) of 1:1 PS/PMMA blends containing the functionalized nanotubes were spin cast and annealed at 180 °C for 12 h. Two different polymer molecular weights were used (M_n = 8000 or M_n = 22,000), and were of approximately equivalent molecular weight to those attached to the surface of the nanotubes. Nanotube functionalization was accomplished using the Cu(I)‐catalyzed [3 + 2] Huisgen cycloaddition, in which alkyne‐decorated nanotubes were coupled with azide‐terminated polymers, resulting in polymer‐SWNT conjugates that were soluble in THF. Characterization of the annealed films by scanning Raman spectroscopy, which utilized the unique Raman fingerprint of carbon nanotubes, enabled accurate mapping of the functionalized SWNTs within the films relative to the two phase‐separated polymers. It was found that nanotube localization within the phase‐separated polymer films was influenced by the type of polymer attached to the nanotube surface, as well as its molecular weight. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 450–458, 2009     

Retardation of shape change of Au nanorods using photo-cross-linkable ligands

The thermal reshaping of gold nanorods has been slowed by grafting a diblock copolymer [P(S-b-S-N₃)] containing an outer polystyrene (PS) brush and a short, inner photo-cross-linkable PS-azide block. The P(S-b-S-N₃)-Au NRs were dispersed in a PS thin film and reshaping was investigated using scanning electron microscopy and UV–Vis spectroscopy. For P(S-b-S-N₃)-Au NRs in PS, the longitudinal surface plasmon resonance decreased from about 880 toward 750 nm upon annealing at 100 °C, 150 °C, and 200 °C. This blue shift increased in strength as temperature increased. However, this reshaping of P(S-b-S-N₃)-Au NRs was slower than that of Au NRs grafted with a poly(ethylene glycol) brush that was dispersed in poly(methyl methacrylate). By slowing down reshaping at elevated temperature, polymer thin film devices that heat during use (e.g., polarization dependent filters) can exhibit a longer lifetime. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016, 54, 301–307