负载型纳米TiO2复合载体及其CoMo催化剂的酸性及孔特性的研究

总结了复载不同纳米尺度的复合载体及其CoMo催化剂的表面酸性及孔结构特性的表征结果。结果表明，负载型纳米TiO2与基载体γ-Al2O3存在着相互作用。当负载比较少量的纳米TiO2时，复合载体的总酸量随着TiO2含量的增加而增加，超过γ-Al2O3的酸量，但当 TiO2的含量比较高时复合载体的酸量又降低，纳米TiO2优先负载在γ-Al2O3的强酸中心位；负载了CoMo活性组分后酸量增加。不同粒径的纳米TiO2对复合载体和催化剂的酸分布没有明显影响，但对总酸量有影响。对不同尺度TiO2，随着TiO2负载量的增加以及负载金属活性组分的增加，表面积、孔容和最可几孔径均有不同程度的减少。     

负载型纳米TiO2光催化降解活性艳红X-3B染料

光催化氧化;负载型纳米光催化剂;负载型纳米TiO2光催化降解活性艳红X-3B染料     

纳米TiO2膜电极的电化学阻抗谱

纳米TiO2膜电极的电化学阻抗谱;纳米TiO2膜;电化学阻抗谱;催化电极;异相氧化还原电对     

纳米Ni/TiO_2粉体的制备及其光催化性能

以四氯化钛为主要原料,通过溶胶法合成了纳米TiO2和Ni/TiO2粉体。研究发现掺杂镍,能够有效延缓锐钛矿型TiO2向金红石型TiO2转变,提高Ni/TiO2粉体的催化活性;在500℃焙烧的Ni/TiO2催化剂,能较好催化溴甲酚绿染料在紫外光下降解。     

Pd纳米粒子敏化的纳米单层TiO_2-Ru(Ⅱ)螯合物修饰电极对单磷酸鸟苷的电催化氧化行为

利用LB膜技术可控制备了纳米单层的二氧化钛-有机钌螯合物杂化膜,并研究了上述无机-有机杂化膜修饰电极在Pd纳米粒子敏化后对单磷酸鸟苷(GMP)的电催化氧化行为.实验结果表明:(1)纳米单层TiO2/[Ru(phen)2(dC18bpy)]2+(简称为TiO2-Ru)杂化膜的平均厚度为(3.2±0.5)nm;(2)在光照条件下TiO2-Ru杂化膜能有效催化还原[Pd(NH3)4]2+形成粒径位于20～200nm之间的Pd纳米粒子;(3)纳米单层TiO2-Ru/Pd杂化膜能高效催化氧化具有供电子能力的单磷酸鸟苷(GMP),与纳米单层TiO2-Ru杂化膜修饰的ITO电极(ITO/TiO2-Ru)相比,当工作电压为1200mV时,ITO/TiO2-Ru/Pd电极在含有1×10-3molL-1GMP的磷酸盐缓冲液中,单位面积的催化氧化电流提高了约36倍;(4)Pd纳米粒子的引入消除了金属钌螯合物中配体对电子传递的阻碍作用,改变了电子传递途径,从而有效减少了电子空穴对的复合,提高了杂化膜修饰电极(ITO/TiO2-Ru/Pd)的电子传递效率.     

由铜-胺氧化还原引发反应一步法简便制备TiO_2表面接枝聚甲基丙烯酸甲酯纳米杂化粒子

提出并验证了一种通过普通自由基聚合在纳米TiO2表面接枝聚甲基丙烯酸甲酯的简单方法.通过在纳米TiO2粒子表面引入伯胺分子层(纳米TiO2-NH2粒子),利用Cu2+-胺氧化还原体系实现了CuSO4催化纳米TiO2-NH2粒子表面引发甲基丙烯酸甲酯(MMA)的自由基接枝聚合,从而一步得到表面固定有聚甲基丙烯酸甲酯链的纳米TiO2杂化粒子(纳米TiO2-PMMA杂化粒子).红外光谱、热失重分析与电镜的结果都表明PMMA已经被接枝到纳米TiO2粒子表面,且接枝率随着聚合时间的延长而逐渐增大,PMMA链的引入有助于降低纳米TiO2粒子微球的团聚程度、增强与有机溶剂分子的范德华力,从而提高分散稳定性.反应溶液中没有游离均聚物形成.     

无配体Cu2O纳米线催化C—N/C—O偶联反应

介绍了由TiO2纳米阵列管上负载Cu2O纳米线,制备新型纳米催化剂Cu2O/TiO2NTs的方法.应用该新型催化剂,研究了其对卤代芳烃的C—N,C—O偶联反应的催化作用,结果表明Cu2O/TiO2NTs不仅能很好地催化溴代芳烃与氮/氧亲核试剂的反应,而且可顺利催化氯代芳烃的反应,得到中等及优良的产率.催化剂循环使用试验证实,催化剂在该体系中能被回收利用5次收率基本稳定.     

反胶束体系制备负载型TiO2纳米光催化剂

在AOT/异辛烷反胶束体系中制备了粒径为2～5nm的单分散球形TiO₂纳米粒子,用TEM,DSC和XRD等手段对其进行了分析;用浸渍法以小孔分子筛HZSM-5为载体制备了负载型TiO₂纳米粒子,用FTIR,Langmuir及BET等手段进行了表征;用以上2种TiO₂粒子作光催化剂进行了简单模拟废水处理研究,用UV-Vis光谱分析其催化效果表明,负载型TiO₂纳米粒子比纯TiO₂纳米粒子的光催化活性更高.     

低温静电自组装法制备贵金属修饰TiO_2纳米结构薄膜及其增强的光催化性能(英文)

以碱-水热法在金属Ti片上原位生长了TiO2纳米结构(纳米花和纳米线)薄膜,并采用低温静电自组装方法将超细贵金属(金、铂、钯)纳米颗粒均匀沉积于多孔TiO2薄膜上.负载于Ti片上的贵金属/TiO2纳米结构薄膜具有一体化结构、多孔架构和高光催化活性.超高分辨率场发射扫描电子显微镜(FESEM)直接观察表明贵金属纳米颗粒在TiO2表面分布均匀,且颗粒之间相互分离,金、铂、钯纳米颗粒的平均粒径分别约为4.0、2.0和10.0nm.俄歇电子能谱(AES)纵深成分分析表明贵金属不仅沉积于薄膜表面,且大量分布于TiO2纳米结构薄膜内部,其深度超过580 nm.X射线光电子能谱(XPS)分析表明,经300°C下在空气中热处理后,纳米金仍保持金属态,纳米铂部分被氧化成PtOabs,而钯粒子则完全被氧化成氧化钯(PdO).以低温静电自组装法沉积贵金属,贵金属负载量可通过调节组装时间与溶胶pH值来控制.光催化降解甲基橙的结果表明,沉积的纳米金和铂能显著增加TiO2纳米结构薄膜的光催化活性,说明金和铂粒子可促进光生载流子的分离;但负载的PdO对TiO2薄膜的光催化性能增强几乎无作用.     

负载型纳米TiO2复合载体的制备及其酸性研究

采用溶胶-凝胶法在γ-Al2O3上制备出负载型纳为TiO2，并用XRD，TEM对TiO2的晶型及粒子大小进行了表征。结果表明，在550℃煅烧后，TiO2仍为锐钛矿结构，且通过控制制备条件，TiO2粒径可控制在5nm-10nm之间及15nm-20nm之间，TiO2都以纳米粒子的形式高分散负载在γ-Al2O3上。另外，还用NH3-TPD对复合载全进行酸性表征。实验发现，纳米TiO2对复合载体的酸量影响较大。复合载体的酸量并不是随TiO2含量的增加而一直下降，而是先降低，当TiO2含量达到30％后又开始增加。纳米TiO2对复合载体的酸强度和酸度分布影响较小。     

Comparative Study of Homogeneous and Heterogeneous Photocatalytic Redox Reactions: PW(12)O(40)(3-) vs TiO(2)

Polyoxometalates (POMs) as a homogeneous photocatalyst and semiconductor oxide as a heterogeneous photocatalyst share many aspects of similarity in their operating mechanisms. This study systematically compares various photocatalytic oxidation and reduction reactions of PW12O403- (a POM) and TiO2 in water to demonstrate that the two photocatalysts are very different in many ways. Both POM and TiO2 can photooxidize various organic compounds with comparable rates, but the POM-mediated mineralization is markedly slower than the mineralization with TiO2 under the experimental conditions employed in this study. Kinetic studies using tert-butyl alcohol as an OH radical scavenger suggest that OH radicals are the sole dominant photooxidant in POM-mediated degradations regardless of the kind of substrates tested, whereas both OH radicals and direct hole transfers take part in TiO2 photocatalysis. POM immobilization on silica support and surface fluorination of TiO2 significantly modified the kinetics and intermediate distribution. POM-mediated photoreductive dechlorination of CCl4 and trichloroacetate was negligible, whereas the dechlorination with TiO2 was markedly faster. The rate of electron transfer from POM- to reducible substrates seems to be significantly slower than the rate of conduction band electron transfer on TiO2 mainly due to the strong electron affinity of POM. The effects of H2O2 addition on photocatalytic reactivity are also very different between POM and TiO2. Detailed kinetic and mechanistic comparisons between PW12O403- and TiO2 photocatalysts are presented and discussed to understand the similarities and differences.     

以膨胀珍珠岩为载体的漂浮型TiO2光催化剂降解水面浮油

 以膨胀珍珠岩为载体制备了漂浮负载型TiO2光催化剂,并对制备催化剂的工艺条件及水面浮油的光催化降解过程进行了初步研究．通过扫描电镜分析及BET比表面积和TiO2负载量测定,对影响负载型光催化剂漂浮性能的因素进行了分析．以癸烷为水面模拟污染物,考察了其在日光照射下的降解效率．用气相色谱法测定了经不同时间光照后癸烷的残留量,经7h光照后能降解癸烷95％以上．实验结果表明,以膨胀珍珠岩为载体,可制得能长期漂浮于水面的负载型TiO2光催化剂,通过浮油富集和光催化降解机制可对水面浮油进行有效的治理．     

Preparation and characterization of highly photoactive nanocrystalline TiO_2 powders by solvent evaporation- induced crystallization method

Highly photoactive bi-phase nanocrystalline TiO2 photocatalyst was prepared by a solvent evaporation-induced crystallization (SEIC) method, and calcined at different temperatures. The obtained TiO2 photocatalyst was characterized with X-ray diffraction (XRD), transmission electron microscopy (TEM) and BET surface areas. The photocatalytic activity was evaluated by the photocatalytic oxidation of acetone in air. The results show that solvent evaporation can promote the crystallization and phase transformation of TiO2 at 100℃. When calcination temperatures are below 600℃, the prepared TiO2 powders show bimodal pore size distributions in the mesoporous region. At 700℃, the pore size distributions exhibit monomodal distribution of the inter-aggregated pores due to the collapse of the intra-aggregated pores. At 100℃, the obtained TiO2 photocatalyst by this method shows good photocatalytic activity, and at 400℃, its photocatalytic activity exceeds that of Degussa P25. This may be attributed to the fact t     

类蛋结构的可磁分离光催化剂纳米球的制备及催化性能

通过反胶束和静电自组装方法制备了一种类蛋结构的可磁分离光催化剂纳米材料SiO₂@NiFe₂O₄@TiO₂(TSN), 这种光催化剂对甲基橙废水有较好的降解效果, 并显示出了超顺磁性, 通过外加磁场方便地实现催化剂在水中的分离与回收. 该光催化剂纳米球的X射线衍射, TEM和FTIR结果表明, 铁酸镍纳米粒子被包裹在SiO₂内, 形成SiO₂@NiFe₂O₄(SN)纳米球载体, 纳米TiO₂颗粒组装在SN表面, 形成TiO₂光催化壳层. 利用甲基橙的降解考察了光催化剂纳米球的活性, 结果表明, 在NiFe₂O₄和TiO₂之间包覆一层无定形的SiO₂可以显著提高光催化剂纳米球TSN的催化活性.     

Gas-phase photocatalytic oxidation of benzene over titanium dioxide loaded on Bi_(12)TiO_(20)

TiO2 was prepared by sol-gel method using tetrabutyl titanate as precursor. TiO2 was loaded on Bi12TiO20. The photocatalyst with different TiO2 loading was calcined at 723 K. The photocatalytic activity of decomposition gaseous benzene was investigated in a batch reactor. The prepared photocatalyst was characterized by UV-vis diffuse reflectance. The result showed that TiO2/Bi12TiO20 absorbed much more ultraviolet light than Ti02 in the ultraviolet light region and showed red shift. The results indicated that the prepared photocatalyst can greatly promote the photocatalytic activity. The 2.0% TiO2/Bi12TiO20 system exhibited the highest photocatalytic activity.     

TiO_2·SiO_2/beads的制备与性质

研究以空心玻璃微球为载体 ,用Sol gel法制备附载型复合光催化剂的过程 ,并对TiO2 ·SiO2 /beads光催化活性进行评价 .结果表明 :复合型光催化剂TiO2 ·SiO2 摩尔比存在最佳值 ,当n(TiO2 ) /m(SiO2 ) =30 /70时 ,光活性是在同样降解条件下 ,同样含量DegussaP 2 5TiO2 的 2倍左右 .同时研究制备方法、制备条件、TiO2 ·SiO2 摩尔比、TiO2 ·SiO2 /beads吸附性、活化条件、比表面等因素对附载型复合光催化剂活性的影响 .     

TiO2/NaY Composite as Photocatalyst for Degradation of Omethoate

Photocatalytic activities of TiO2 and NaY zeolites-supported TiO2 were investigated with omethoate as a model pollutant.The physical and chemical states of NaY zeolite-supported TiO2 were evaluated via XRD,FTIR,BET and SEM.Photodegradation of omethoate was studied with H2O2 as oxidant and TiO2 supported on NaY zeolite as photocatalyst.Parameters involved in the photo-catalysis of omethoate,i.e.,the calcination temperature of the photocatalyst,initial omethoate concentration,the amount of TiO2 loaded on NaY ...     

纳米TiO2光催化剂改性研究进展

TiO2光催化活性高,化学稳定性好,绿色环保及价廉等特点,在污水处理、有机污染物降解、催化制氢、抗菌抗癌及自清洁等方面有巨大的应用前景。然而TiO2半导体禁带宽,光谱范围小,光量子效率低等问题限制了其光催化性能。文章综述了TiO2光催化剂优化改性的研究进展,系统分析了TiO2半导体的结构特征与作用机理,以及TiO2光催化过程的影响因素,着重介绍了TiO2光催化剂多元优化改性方法的优势及不足,最后对未来发展新型TiO2基光催化剂提出了建议。     

TiO2负载膜的制备、表征及光催化性能

采用溶胶－凝胶法制备了ＴｉＯ２纳米浸渍 法将其负载于颗粒形活性炭的表面制成ＴｉＯ２负载,利用ＳＥＭ,ＥＤＳ和ＸＲＤ等手段对膜的形貌、均匀性及晶型等进行了表征,并通过甲基橙水溶液的光催化降解反应考察了该负载膜的光催化活性。     

半导体复合TiO2纳米光催化剂

对近年来利用半导体复合TiO2纳米光催化剂进行了介绍。总结了复合TiO2纳米光催化剂的制备、复合物的种类、光催化机理以及影响半导体复合TiO2光催化性能的因素。