Wavelength-tunable organic solid-state distributed-feedback laser

We report on a wavelength-tunable organic solid-state laser based on a second-order distributed-feedback (DFB) resonator design with the guest–host system Alq₃:DCM2 as the gain medium. The laser wavelength can be shifted from 608.9 to 646.5 nm by varying the grating period of the Bragg reflector. This allows the characterization of laser parameters for a large wavelength region on a single sample. The laser threshold and output characteristics are measured for different laser wavelengths. A minimum threshold for laser activity occurs at a lasing wavelength of 633 nm, giving the spectral position of the gain maximum. PACS 42.70.Jk; 78.45.+h; 78.66.Qn     

Ⅲ–Ⅴ/Si Hybrid Laser Array with DBR on Si Waveguide

We report an eight-channel silicon evanescent laser array operating at continuous wave under room temperature conditions using the selective-area metal bonding technique.The laser array is realized by evanescentl.y coupling the optical gain of InGaAsP multi-quantum wells to the silicon waveguides of varying widths and patterned with distributed Bragg reflector gratings.The lasers have emission peak wavelengths in a range of 1537-1543 nm with a wavelength spacing of about 1.0 nm.The thermal impedances Z_T of these hybrid lasers are evidently lower than those DFB counterparts     

Single-frequency thulium-doped distributed-feedback fiber laser

We have successfully demonstrated a single-frequency distributed-feedback (DFB) thulium-doped silica fiber laser emitting at a wavelength of 1735 nm. The laser cavity is less than 5 cm long and is formed by intracore UV-written Bragg gratings with a phase shift. The laser is pumped at 790 nm from a Ti:sapphire laser and has a threshold pump power of 59 mW. The laser has a maximum output power of 1 mW in a single-frequency, single-polarization radiation mode and is tunable over a few nanometers. To the best of the authors' knowledge, this is the first report of a single-frequency DFB fiber laser that uses thulium as the amplifying medium. The lasing wavelength is the longest demonstrated with DFB fiber lasers and yet is among the shortest obtained for thulium-doped silica fiber lasers.     

Highly reliable strain-tuning of an Erbium-doped fiber laser for the interrogation of multiplexed Bragg grating sensors

The authors implemented a tunable linear cavity Erbium-doped fiber (EDF) laser for the interrogation of multiplexed fiber Bragg grating sensors (BGS). A high-strength single-pulse draw-tower fiber Bragg grating (FBG) was used as the mechanically tunable element enabling the rapid wavelength sweeping of the laser center wavelength. A simple algorithm to process the noisy acquired data and identify the peak of the BGS spectra was employed. For the first time, this type of configuration was used to reliably interrogate at least three fiber Bragg grating sensors with a standard wavelength spacing between the Bragg wavelengths of 3 nm, without risk of breaking the stretched fiber, using an FBG with a simple PZT driven mount as the tuning elements.     

激光烧蚀制备分布反馈式有机激光器件

采用激光烧蚀的方法结合激光全息技术,直接在高分子聚合物MEH-PPV薄膜表面烧蚀光栅结构,制备了分布反馈式有机激光器。这一方法具有工艺简单、光栅参数的可控性和重复性好等优点。器件MEH-PPV的膜厚是400 nm。利用波长为355 nm的Nd-YAG纳秒激光器进行单脉冲烧蚀,获得的光栅周期和光栅高度分别为370 nm和 100 nm。利用飞秒激光放大器作为泵浦源激射DFB激光器件,得到激射阈值约为182 μJ·cm^-2·pulse^-1,光谱的波峰约在609 nm处,半高宽为4.2 nm。通过改变两光束的夹角获得了周期为360, 370, 380, 390 nm的光栅,它们对应的激光波峰分别为602.91, 609.24, 613.26, 619.01 nm。     

基于半导体纳米线和金属脊的混合表面等离子体波导模式特性分析

波长可开关光纤激光器可以选择多波长光纤激光器中的一个或多个波长输出,支持光网络中多个波长的动态分配,适应现代光纤通信系统信道数越来越多的波分复用和密集波分复用的发展方向.本文提出并实现了一种自激发多波长可开关掺铒光纤激光器.该激光器通过一个980 nm泵浦进行抽运,使用掺铒光纤作为增益介质,产生1 550 nm光谱,并通过一个环形结构返回,从而实现自激发的过程,降低了实验成本.实验使用一个含有两段保偏光纤的Sagnac环作为滤波器.通过调整Sagnac环形滤波器内偏振控制器的角度,改变Sagnac环形滤波器的腔内增益,可以让光纤光栅反射出来的波长选择性通过,从而实现波长的开关功能.实验证明,通过调整Sagnac滤波器的腔内增益而让多波长选择性通过,是一种有效的实现波长可开关功能的方法.     

Widely tunable,narrow linewidth Tm: YAG ceramic laser with a volume Bragg grating

We report on a widely tunable, narrow linewidth operation of a Tm:YAG ceramic laser. A volume Bragg grating is used in the cavity as a folding mirror for wavelength selection. The wavelength is tuned from 1956.2 to1995 nm, leading to a total tuning range of 38.7 nm. The linewidth is around 0.1 nm over the whole tuning range. A maximum output power of 1.51 W at 1990.5 nm is achieved at 37.8 W absorbed pump power.Different saturation behaviors are observed in the laser performances at different wavelengths.     

A stable dual-wavelength fiber laser with tunable wavelength spacing using a polarization-maintaining linear cavity

We propose and experimentally demonstrate a stable dual-wavelength erbium-doped polarization-maintaining (PM) fiber laser with tunable wavelength spacing using an all-PM linear cavity that makes use of two reflection peaks from the PM fiber Bragg grating (PM-FBG). Experimental results show stable dual lasing lines with a wavelength separation of ∼0.22 nm and a large optical signal-to-noise ratio (OSNR) of over 40 dB under room temperature. By applying axial strain to the PM-FBG, the center wavelengths of the two lasing lines can be tuned over several nanometers and the wavelength separation between the lasing lines can also be tuned to as small as 0.05 nm, which, to our knowledge, is the smallest wavelength spacing ever obtained from a stable room-temperature dual-wavelength fiber laser. The proposed laser configuration has the advantages of simple structure, low loss, stable dual-wavelength operation and a very small lasing linewidth of ∼5 kHz . PACS 42.55.Wd; 42.81.-i; 42.81.Gs     

Tunable dual-wavelength fiber laser based on a single fiber Bragg grating in a Sagnac loop interferometer

We propose a simple dual-wavelength Er-doped fiber laser configuration based on a dual-wavelength fiber Bragg grating written on the splice joint between two different fibers for wavelength-selective filter in the Sagnac loop interferometer. The wavelength separation between the adjacent lasing wavelengths is 1.12 nm and the side-mode suppression ratio (SMSR) is over 55 dB. The output power variation is less than 0.8 dB over a two-minute period. Moreover, the lasing wavelength can be effectively tuned using the thermal heating method.     

Switchable dual-wavelength Erbium-doped fiber ring laser with cascaded fiber Bragg gratings

We have experimentally shown wavelength mode switching in a dual-wavelength Erbium-doped single cavity fiber laser where the initial two wavelengths of 1 nm spacing are determined by the cascaded reflection type short-period fiber Bragg gratings having two different centre wavelengths of 1550.5 and 1551.5 nm. The lasing mode depends on the polarization in the ring cavity to migrate from one wavelength to another or operates in both modes in a polarization beam splitter output. To effectively control the polarization in the ring cavity, the polarization controllers were positioned before and after the polarization beam splitter. This method of wavelength switching provides a simple way of mode tuning in dual-wavelength fiber lasers.     

体布拉格光栅外腔半导体激光器光谱特性研究

用体布拉格光栅(VBG)作为反馈元件与瓦级半导体激光器(LD)以及快轴准直柱透镜构成一个可以将半导体激光器的工作波长稳定在体布拉格光栅布拉格波长处的外腔激光器。测量了体布拉格光栅外腔激光器的波长稳定性与其工作电流、热汇温度、激光束准直装置等因素的关系。分析了波长稳定效果与半导体激光器增益谱特性、外腔结构参量等因素的关系。研究表明,在相同的工作电流、热汇温度下,当准直柱透镜直径为0.4 mm时的波长稳定效果较好;在此情况下,当热汇温度控制在30℃,工作电流从0.5 A增加到1.5 A的测量范围内,以及当工作电流固定在1.5 A,热汇温度从20℃增加到35℃时,测得的光谱特性表明,半导体激光器的工作波长可以很好地稳定在体布拉格光栅的布拉格波长处。与该激光器在同样条件下自由运转的光谱比较,可以看到,自由运转激射波长与体布拉格光栅的布拉格波长差值小于2.6 nm情况下,可以获得很好的波长稳定效果。实验也表明,当该值大于4.8 nm时波长稳定效果变差。     

用偏振烧孔实现的室温双波长光纤激光器

本文提出一种简单的掺铒光纤激光器的结构,在室温下实现了稳定的双波长激光运转.在该结构中,使用刻写在保偏光纤上的光纤布喇格光栅作为波长选择器件. 实验表明,通过调整偏振控制器的状态,在室温下能够得到稳定的双波长激光输出,波长间隔0.52 nm,16次重复扫描对应于每一波长的振幅变化及波长间振幅差异均小于0.2 dB.     

A 795 nm gain coupled distributed feedback semiconductor laser based on tilted waveguides

The 795 nm distributed feedback lasers have great application in pumping the Rb D1 transition. In this paper, in order to realize specific 795 nm lasing, we designed tilted ridge distributed feedback lasers based on purely gain coupled effect induced by periodic current injection windows through changing the angle of the tilted ridge. The fabricated devices were cleaved into 2 mm-cavity-length, including 5 tilted angles. The peak output powers of all devices were above 30 m W.Single longitudinal mode lasing was realized in all tilted Fabry–Perot cavities using periodic current injection windows,with side mode suppression ratio over 30 d B. The total wavelength range covered 8.656 nm at 20℃. It was disclosed theoretically and experimentally that the output powers, threshold currents, and central wavelengths of the tilted ridge purely gain coupled DFB lasers were relevant to the tilted angles. The results will be instructive for future design of DFB laser arrays with different central wavelengths.     

电流调谐光纤光栅外腔分布布拉格反射激光器

报道一种新颖的波长可调谐光纤光栅外腔分布拉格反射激光器。把经过金属管封装的光纤面布拉格光栅作为激光二极管的外腔反射镜,得到的单模激光输出不仅线宽窄,边模抑制比高,而且,调节流过金属管的电流,可在5nm范围内的6个不同波长间转换。     

Low-Threshold Conjugated Polymer Distributed Feedback Lasers on InP Substrate

We demonstrate a low threshold polymer solid state thin-film distributed feedback （DFB） laser on an InP substrate with the DFB structure. The used gain medium is conjugated polymer poly[2-methoxy-5-（2-ethylhexyloxy）-l, 4- phenylenevinylene] （MEH-PPV） doped polystyrene （PS） and formed by drop-coating method. The second order Bragg scattering region on the InP substrate gave rise to strong feedback, thus a lasing emission at 638.9nm with a line width of 1.2nm is realized when pumped by a 532nm frequency-doubled Nd：YAG pulsed laser. The devices show a laser threshold as low as 7n J/pulse.     

Multi-point, fiber-optic gas detection with intra-cavity spectroscopy

A novel intra-cavity fiber laser system is demonstrated for multi-point gas detection. The laser uses fiber Bragg gratings as wavelength-selective cavity mirrors and a tunable filter to tune the operating wavelength to the Bragg wavelength of a selected Bragg grating. The Bragg wavelengths of the gratings are chosen to be aligned to different absorption lines of a gas or gases, allowing gas concentrations at multiple locations to be determined.     

HF-based clad etching of fibre Bragg grating and its utilization in concentration sensing of laser dye in dye–ethanol solution

This paper presents a fibre Bragg grating (FBG) based sensor to study the concentration of laser dye in dye–ethanol solution. The FBG used in this experiment is indigenously developed using 255 nm UV radiations from copper vapour laser. The cladding of the FBG was partially removed using HF-based etching to make FBG sensitive to changes in the surrounding refractive index. The experimental results on the shift of the Bragg peak wavelength with HF etching and different dye concentration in ethanol are presented. The Bragg wavelength shifted from 1534.670 nm to 1534.225 nm in 30 min and from this point to 1533.97 in the next 2 min. The clad-etched Bragg peak shifted almost linearly from 1534.056 nm to 1534.162 nm as surrounding dye concentration in ethanol changes from 0 mM to 1.5 mM. It was observed that sensitivity depends on the concentration of the solution and found to be 70 pm/mM.     

大功率多波长可转换双包层光纤激光器

在多模掺镱双包层光纤上,利用相位掩模法直接写制Bragg光栅作为激光器后腔镜,得到多波长激光输出.在室温下,通过调节偏振控制器可以得到稳定的单波长及多波长的激光输出,输出波长范围在1 056～1 061 nm,线宽均小于0.02 nm.在25 W的976 nm激光泵浦下,激光器得到功率为6 W的多波长输出.     

基于级联光纤Bragg光栅的外腔半导体激光器三波长同时激射

实现了使用3个级联的光纤Bragg光栅外腔半导体激光器3波长同时激射.3条谱线的峰值波长取决于光纤Bragg光栅的峰值反射波长,分别为1 531.5 nm、1 549.4 nm与1 554.8 nm.注入电流为52 mA时,激光器总输出功率为1 mW.该激光器的主要优点包括,由于输出波长被锁定在光纤Bragg光栅的Bragg波长上,因此输出波长稳定,谱线窄,成本低.可应用于多波长干涉测量以及全光通信等领域中.     

用于机械振动实时监测的光纤光栅有源传感装置

把一对中心反射波长分别为1562.11nm和1562.71nm的光纤光栅粘贴在均质、等厚、等腰三角形悬臂梁上下表面作为环形腔光纤激光器端镜，当机械振动激励自由端时，通过观测激光输出脉冲，地施加于自由端的机械振动的频率进行了实时监测；观察两光栅波长漂移量差值的变化，可在0～6.1mm的范围内判断所测振动的振幅。低于100Hz时，实验结果与实际值基本吻合。