紧凑型激光二极管抽运全固态355 nm连续波紫外激光器

报道了一台激光二极管端面抽运Nd:YVO₄晶体内腔三倍频355 nm激光连续输出的全固态紫外激光器.激光腔采用紧凑型简单凹平直腔,腔长仅为70 mm.利用两块LBO晶体进行腔内倍频、和频,当注入抽运功率为2527 W时,获得最大功率为306 mW的355 nm连续波输出,光光转换效率为012％,输出功率短期不稳定性为53%,355 nm激光输出光束质量良好.通过采用内腔倍频技术和设计合理的腔参数,实现了中小功率连续输出的全固态紫外激光器的小型化、便携化,进一步拓宽了紫外激光器 关键词： 激光二极管端面抽运 内腔三倍频 连续波 355 nm激光     

瓦级激光二极管端面抽运351nm紫外激光器

研制了输出功率达瓦级的351 nm准连续紫外激光器。激光器采用激光二极管(LD)端面抽运Nd∶YLF晶体和声光调Q技术,实现了1 053 nm准连续基波振荡。在结构简单的V型腔中,两块Li B3O5(LBO)晶体对基频光进行二倍频和三倍频,获得了高功率351 nm准连续紫外激光输出。在LD抽运功率为14 W、声光调Q激光器的调制频率为1 k Hz的工作条件下,得到351 nm紫外激光平均输出功率为1.12 W、脉冲宽度为34 ns、单脉冲能量为1.12 m J、峰值功率达32.94 k W。LD抽运光到351 nm紫外激光的光-光转换效率达到8%,电光效率为3.4%,光束质量良好。     

PPKTP晶体半整体谐振腔倍频的397.5nm紫外激光输出

外腔谐振倍频是获得397.5 nm紫外激光的重要方法。搭建了基于周期极化的磷酸氧钛钾(PPKTP)晶体的半整体谐振腔,对经半导体锥型放大器放大的795 nm单频连续激光进行谐振倍频。在203 m W的795 nm基频光输入条件下,实现了60.4 m W的397.5 nm连续单频紫外激光输出,倍频转化效率为30%;在基频光功率约87.5 m W时,得到最大的倍频效率约为34.6%。倍频紫外光光束质量因子M2优于1.21,光束质量良好,30 min内典型的倍频光功率均方根起伏小于1.9%。该倍频器结构紧凑,具有很好的机械稳定性,可实现紫外激光的稳定输出,可用于产生对应铷原子跃迁线的压缩、纠缠态光场,在量子光学和精密测量等领域发挥重要作用。     

利用椭圆高斯光束产生266nm紫外连续激光

本文采用商用532 nm激光器作为基频光源,利用偏硼酸钡(β-BBO)晶体进行外腔倍频,实现了266 nm连续激光的高效输出.文中详细模拟了BBO晶体中的束腰形状对倍频效率的影响,仿真和实验结果均表明椭圆高斯光束可以有效改善走离效应,提高倍频转换效率.通过优化蝶形倍频腔,可以使椭圆高斯光束在腔内共振,当1 W基频光输入时可输出约180 mW的266 nm紫外连续激光,倍频转换效率达到18%.     

紧凑型LD端面抽运Nd:YAG内腔三倍频准连续355 nm紫外激光器

报道了一台LD端面抽运Nd:YAG晶体内腔三倍频355 nm激光高效率、高峰值功率准连续输出的全固态紫外激光器.激光腔采用紧凑型平平直腔,腔长仅106 mm.当注入抽运功率为5.73 W、重复频率为9 kHz时,获得163 mW的355 nm激光准连续输出,光光转换效率达到最高2.84％.当注入抽运功率为6.7 W重复频率为5 kHz时,获得最高174 mW的355 nm激光准连续输出,输出功率短期不稳定性为5％,光束质量因子M²为3.79.当注入抽运功率为5.73 W、重复频率为2 kHz时,获得112 mW的355 nm激光准连续输出,峰值功率最高达到9.15 kW.通过采用内腔倍频技术和设计合理的腔结构,实现了中小功率准连续输出的全固态紫外激光器的小型化、便携化,进一步拓宽了紫外激光器的应用领域. 关键词： LD端面抽运 内腔三倍频 Q')" href="#">声光调Q 紫外激光     

LD脉冲侧面泵浦Nd∶YAG电光调Q低重频窄脉宽紫外激光器

介绍了在1~20 Hz电光调Q情况下,半导体脉冲激光侧面泵浦Nd∶YAG晶体腔外四倍频266 nm紫外激光器的输出特性.实验采用直腔结构,在腔外分别利用KTP和BBO晶体产生532 nm倍频绿光、266 nm四倍频紫外激光.当泵浦电流为120 A、重复率为1 Hz时,266 nm紫外激光最大单脉冲能量为15.4 mJ、脉宽8 ns,峰值功率高达1.93 mW;重复率20 Hz时,获得了最大平均功率为156.2 mW的266 nm紫外激光输出,四倍频的转换效率为10.63％.同时利用一组分光镜,获得了352 mW的532 nm脉冲绿光和423 mW的1 064 nm脉冲红外光输出.     

LD泵浦全固态355nm紫外皮秒脉冲激光器

利用激光二极管（LD）端面抽运Nd∶YVO4激光晶体皮秒三倍频355nm全固态紫外激光器,采用半导体可饱和吸收镜（SESAM）锁模技术及皮秒再生放大技术,对1 064 nm基波采用Ⅰ类相位匹配Li3B3O5（LBO）晶体二倍频和Ⅱ类相位匹配LBO晶体三倍频,获得了稳定性好、倍频效率较高的355 nm紫外激光输出。当二极管泵浦功率为5 W时,获得了脉宽为17 ps、重复频率为1 Hz、单脉冲能量为129.6 J的稳定三倍频紫外激光输出,基频光到二倍频光和三倍频光的转换效率分别达到60.3%和16.6%,3 h输出单脉冲能量的抖动在0.58%以下。     

全固态飞秒激光高光束质量三倍频研究(特邀)

对全固态飞秒激光三倍频产生高光束质量343 nm飞秒激光进行了系统研究。基频光源为脉冲宽度为105 fs、重复频率为76 MHz、中心波长为1 030 nm的商用Yb:KGW锁模激光器,利用1.7 mm长LBO晶体获得60%的二倍频转换效率,然后分别研究了基于BBO晶体Ⅱ类相位匹配和Ⅰ类相位匹配的三倍频产生。在基频光功率为5 W的条件下,利用Ⅱ类相位匹配的BBO晶体,获得的最大平均功率为0.71 W,三倍频转换效率约为14%;利用Ⅰ类相位匹配的BBO晶体,获得平均功率为1.01 W的紫外激光输出,三倍频转换效率为20.2%。获得的343 nm紫外激光的光束质量优于1.3。     

激光二极管侧面泵浦高功率266 nm紫外激光器

 报道了一种半导体激光列阵侧面泵浦Nd：YAG四倍频266 nm全固态紫外激光器,采用Z型腔结构,Ⅰ类临界相位匹配LBO和BBO晶体分别作为二倍频晶体和四倍频晶体。在调制频率为5 kHz时,最终获得了2.1 W的266 nm紫外激光输出,单脉冲能量420 μJ, 绿光到紫外激光的转换率为13.13%,在相同的泵浦功率下利用V型腔结构仅获得305 mW的266 nm紫外激光输出。     

BBO晶体四倍频全固态小功率紫外激光器

 利用KTP晶体和BBO晶体,进行了激光二极管泵浦的Nd:YVO₄声光调Q激光脉冲四倍频实验。在不同绿光功率入射时,获得光束的束腰半径和紫外转换效率的依赖关系:当绿光功率为1.10 W,束腰半径为12.4 μm时,得到了210 mW的准连续266 nm紫外脉冲输出,四倍频转换效率为19.1%。实验还对紫外远场光斑分别在o光振动面和e光振动面内进行分析,指出了BBO晶体在该两平面内不同的倍频接受角是造成椭圆形紫外光斑和主光斑附近明暗条纹的主要原因。     

Size parameter effect of dielectric small particle mediated nano-hole patterning on silicon wafer by femtosecond laser

By use of a polystyrene particle with a fundamental (800 nm) and a second-harmonic (400 nm) wave of a femtosecond Ti:sapphire laser, nano-hole patterning properties on a silicon wafer were experimentally compared by keeping the size parameter constant. With the 800-nm wave, the patterned hole diameter ranged from 100 to 250 nm and the depth ranged from 20 to 100 nm. With the 400-nm wave, the hole diameter ranged from 50 to 200 nm while the depth ranged from 10 to 60 nm. The patterned diameter and the depth of patterned nano-holes were also controllable by the laser fluence. By the 3D finite-difference time-domain method it is numerically predicted that if the size parameter is kept at π approximately, the nano-hole patterning is efficiently performed even in the ultraviolet region of the spectrum.     

高效全固化紫外四倍频激光器的研究

用半导体激光器抽运的调Q YLF倍频激光器抽运掺钛蓝宝石激光器，用LBO晶体在腔内产生二次谐波，再聚焦到BBO晶体上产生四次谐波深紫外激光。为了提高谐波转换效率，在腔内分别插入了单片、组合双折射滤光片和聚焦透镜，在平均功率为3.6W，波长为527nm的抽运光下得到410mW，417nm的蓝光。用长焦距的透镜聚焦二次谐波，得到34mW，208nm的紫外脉冲激光。从实验上详细研究了基频光的线宽对二次谐波效率的影响，二次谐波的线宽对四次谐波效率的影响、基频光的波长对四次谐波产生效率的影响。全面地分析了单片和组合大拆射滤光片及抽运功率对钛蓝宝石激光器基频光的脉宽、线宽等参量的影响。     

Watt-level continuous-wave intracavity frequency-doubled Pr:YLF-LBO laser at 320 nm

We report on diode-pumped continuous-wave Pr-doped yttrium lithium fluoride(Pr:YLF) laser and its frequency doubling to320 nm. The maximum output power of the 640 nm fundamental wave reached 3.44 W with a slope efficiency of about 48.3%.Using a type-I phase-matched lithium triborate(LBO) crystal as a frequency doubler, we have achieved 320 nm ultraviolet radiation with a maximum output power of 1.01 W, which is the highest power ever reported under diode pumping, to the best of our knowledge.     

BeAl2O4:Cr3+紫外光谱的研究

在强场理论的基础上,本文考虑了组态相互作用,拟合了各能级位置,并对其紫外光谱进行了讨论.     

Ultrabroadband phase-matched optical parametric generation in the ultraviolet by use of guided waves

We present what is believed to be the first experimental demonstration of guided-wave phase-matched frequency mixing and harmonic conversion in gases. Broad-bandwidth ultrafast pulses, tunable around 270 nm, were generated from an ultrafast Ti:sapphire amplifier system using 2? + 2? - ? parametric wave mixing in a capillary waveguide. We achieved nonresonant phase matching by coupling both the fundamental and the second-harmonic light into the lowest-order mode. The output 3? pulses have an energy of >4muJ at a 1-kHz repetition rate. Simple extensions of this method can generate higher-energy 10-20-fs pulses tunable throughout the vacuum ultraviolet.     

高能量高转换效率355 nm紫外激光器

为了得到一种三倍频效率高达60%的355 nm脉冲激光器,采用曲率半径分别为2 m的凹凸高斯镜和9 m的平凹全反镜组合作为谐振腔,加以电光调Q,得到1 064 nm高光束质量激光输出,再将其进行行波放大,获得重复频率10 Hz、脉宽7.3 ns、单脉冲能量1.01 J的1 064 nm基频光输出。利用Ⅰ类相位匹配LBO晶体进行二倍频、Ⅱ类相位匹配LBO晶体进行三倍频以得到波长为355 nm的紫外光输出。通过二倍频和三倍频输出特性和非线性晶体参数的分析和实验调试,最终获得了单脉冲能量为608 mJ、脉宽为5.7 ns、线宽为2 nm的紫外激光输出。通过优化二倍频的转换效率,可使1 064 nm基频光到三倍频得到的355 nm紫外光的转换效率达60%。     

Tunable frequency-controlled laser source in the near ultraviolet based on doubling of a semiconductor diode laser

Continuously tunable ultraviolet laser radiation at 397 nm was generated by doubling the output of a semiconductor diode laser. The fundamental radiation was provided by a 150 mW AlGaAs laser diode injected by a low-power AlGaAs laser diode which was frequency stabilized by optical feedback using a new scheme of a miniature external cavity. Second-harmonic generation was produced in a lithium-triborate crystal placed in a compact enhancement cavity. The fundamental radiation was used for sub-Doppler spectroscopy of the Ar I 4s ³ P ⁰ ₀–4p ¹ P ₁ transition at 795 nm; the second-harmonic radiation was used for spectroscopy of the Ca II 4² S _1/2–4² P _1/2 transition at 397 nm.     

Absorption,excitation and fluorescence spectra of thallium activated cesium bromide

Absorption, excitation and fluorescence spectra of T1⁺ doped cesium bromide have been investigated at various thallium concentrations. At very low thallium concentration two absorption bands are obtained at 225 nm and 264 nm. With rise of thallium concentration additional absorption bands are obtained at 230, 244, 258, 270 and 285 nm. A single bell-shaped fluorescence band at 357 nm in the ultraviolet region is obtained at low thallium concentration. Two additional visible fluorescence bands appear at 440 and 540 nm with rise in thallium content. The excitation spectra for ultraviolet emission band and visible emission bands are found to be different. Accordingly the ultraviolet emission band is attributed to the characteristic A emission in T1⁺ ion and the visible bands are attributed to dimer centers havingD _4h site symmetry.     

LD泵浦355nm准连续紫外激光器

报道了一台LD侧面泵浦Nd:YAG晶体的内腔三次谐波转换的全固态准连续紫外激光器。在谐振腔内,1064nm的基频波通过对Ⅱ类相位匹配KTP晶体进行二倍频来产生532nm波长激光,二者再通过对Ⅱ类相位匹配LBO晶体进行和频来获得355nm紫外激光输出。355nm全固态紫外激光器在声光调Q重复频率为2.8kHz下,当输入电流为18A时可得到503mW的激光输出。