The influence of the rhenium in the precursor film on the properties of the thin superconducting films based on thallium

Thin films of thallium based superconductors have been prepared on a CeO₂ buffered R-plane sapphire as well as on a LaAlO₃ substrate using an RF magnetron sputtering and an ex situ thallination in a one zone configuration. We have studied the influence of the presence of the rhenium in the precursor film on structural and electrical properties of the final films. Our results show that the presence of the rhenium in the precursor films caused the significant changes in the morphology of the prepared films.     

Analysis of the substrate effects of strain-hardening thin films on silicon under nanoindentation

Mechanical properties of thin films on substrates can be evaluated directly through nanoindentation. For a comprehensive study, thin films should be characterized via Young’s modulus, yield stress and strain-hardening exponent at constant temperature. In this paper, we evaluate these effects of thin films on silicon substrate through finite element analysis. Thin films, from soft to hard relative to the silicon substrate, are investigated in three categories: soft films on hard substrates, soft to hard films on no elastic mismatch substrates, and hard films on soft substrates. In addition to examining the load-displacement curve, the normalized hardness versus normalized indentation depth is checked as well to characterize its substrate effect. We found that the intrinsic film hardness can be acquired with indentation depths of less than 12% and 20% of their film thickness for soft films on hard substrates and for soft to hard films on no elastic mismatch substrates, respectively. Nevertheless, nanoindentation of hard films on soft substrates cannot determine the intrinsic film hardness due to the fact that a soft substrate cannot support a hard film. By examining the von Mises stresses, we discovered a significant bending phenomenon in the hard film on the soft substrate. PACS 61.43.Bn; 62.20.-x; 68.03.Hj; 68.05.Cf; 68.08.De     

The influence of the substrate nature on the iron repartition in the titania matrix

Fe-doped titania films were deposited by RF sputtering onto different substrates (glass and ITO/glass) in the same deposition run. The rutile nanocrystalline structure of Fe-doped thin films deposited on glass substrates and anatase nanocrystalline structure of Fe-doped thin films deposited on ITO/glass substrates were evidenced by XRD. SEM investigations showed a smooth surface with a dense nanostructure. XPS study evidenced an almost stoichiometric composition with different iron contents. EPR and XPS studies evidenced that iron entered into TiO₂ lattice by substitution, as isolated and dimer species. In Fe-doped thin films deposited on ITO/glass substrates the iron content is ten times higher than in Fe-doped thin films deposited on glass substrates and that a part of them entered as Fe²⁺.     

Effect of post-annealing on the properties of copper oxide thin films obtained from the oxidation of evaporated metallic copper

Thin films of copper oxide were obtained through thermal oxidation (100-450 °C) of evaporated metallic copper (Cu) films on glass substrates. The X-ray diffraction (XRD) studies confirmed the cubic Cu phase of the as-deposited films. The films annealed at 100 °C showed mixed Cu-Cu₂O phase, whereas those annealed between 200 and 300 °C showed a single cubic Cu₂O phase. A single monoclinic CuO phase was obtained from the films annealed between 350 and 450 °C. The positive sign of the Hall coefficient confirmed the p-type conductivity in the films with Cu₂O phase. However, a relatively poor crystallinity of these films limited the p-type characteristics. The films with Cu and CuO phases show n-type conductivity. The surface of the as-deposited is smooth (RMS roughness of 1.47 nm) and comprised of uniformly distributed grains (AFM and SEM analysis). The post-annealing is found to be effective on the distribution of grains and their sizes. The poor transmittance of the as-deposited films (<1%) is increased to a maximum of ∼80% (800 nm) on annealing at 200 °C. The direct allowed band gap is varied between 2.03 and 3.02 eV.     

Effects of crystalline quality on the ultraviolet emission and electrical properties of the ZnO films deposited by magnetron sputtering

The ZnO films were deposited on c-plane sapphire, Si (0 0 1) and MgAl₂O₄ (1 1 1) substrates in pure Ar ambient at different substrate temperatures ranging from 400 to 750 °C by radio frequency magnetron sputtering. X-ray diffraction, photoluminescence and Hall measurements were used to evaluate the growth temperature and the substrate effects on the properties of ZnO films. The results show that the crystalline quality of the ZnO films improves with increasing the temperature up to 600 °C, the crystallinity of the films is degraded as the growth temperature increasing further, and the ZnO film with the best crystalline quality is obtained on sapphire at 600 °C. The intensity of the photoluminescence and the electrical properties strongly depend on the crystalline quality of the ZnO films. The ZnO films with the better crystallinity have the stronger ultraviolet emission, the higher mobility and the lower residual carrier concentration. The effects of crystallinity on light emission and electrical properties, and the possible origin of the n-type conductivity of the undoped ZnO films are also discussed.     

Effect of N2 ambient annealing on the field emission properties of HfNxOy thin films

HfN_xO_y thin films were deposited on Si substrates by direct-current sputtering. The influence of N₂ ambient annealing on the morphology, structure and field emission properties of the HfN_xO_y thin films was studied systematically. Scanning electron microscopy indicates that both the as-deposited and the annealed films are composed of nanoparticles, and the particle sizes of these films do not change much before and after annealing. Atomic force microscopy shows that the surface of the as-deposited films is smooth while that of the annealed films becomes rough, with many protrusions. X-ray diffraction patterns demonstrate that the as-deposited films are amorphous while the samples annealed at over 500 °C are polycrystalline. It is found that the field electron emission properties of the annealed films are better than those of the as-deposited films. The film annealed at 800 °C shows the best field emission properties. The mechanism for the improvement of the field electron emission property of the annealed thin films is also discussed. PACS 73.61.-r; 79.70.+q; 81.05.-t     

Effects of substrate temperature on the efficiency of hydrogen incorporation on the properties of Al-doped ZnO films

Al-doped ZnO (AZO) transparent conducting films were successfully prepared on glass substrates by RF magnetron sputtering at different substrate temperatures in Ar and H₂ + Ar sputtering ambient. The effects of substrate temperature on the effectiveness of hydrogen incorporation in Al-doped ZnO films were investigated. The microstructural, electrical and optical properties of AZO films were systematically analyzed by surface profiler, X-ray diffractometry, scanning electron microscope, four-point probe measurement and UV/vis spectrophotometer. The XRD patterns and SEM pictures indicate that the crystallinity of AZO thin films was markedly improved with hydrogen incorporation at low substrate temperature, while the improvement of crystallinity was not an obvious change at high substrate temperature. The results also indicate that hydrogen incorporation has the stronger effectiveness on the transparent conductive properties of AZO films with the substrate temperature decreasing. The resistivity of the films decreases, especially for lower substrate temperatures, due to the incorporation of hydrogen atoms. These results suggest that substrate temperature should be controlled to the lower level to effectively reduce resistivity without detriment to transmittance of AZO thin films when hydrogen is incorporated.     

Influence of sulfidation treatment on the structure and tribological properties of nitrogen-doped diamond-like carbon films

The nitrogen-doped diamond-like carbon (DLC) films were deposited on high speed steel (HSS) substrates in the direct current unbalanced magnetron sputtering system. Sulphurized layer was formed on the surface of DLC films by means of liquid sulfidation in the intermixture of urea and thiourea solution in order to improve the tribological properties of DLC films. The influence of sulfidation treatment on the structure and tribological properties of DLC films was investigated in this work. The structure and wear surface morphology of DLC films were analyzed by Raman spectroscopy, XPS and SEM, respectively. It reveals that the treated films are smooth and uniform; and sulfur atoms are bonded chemically. The treated films have broader distribution of Raman spectra in the range of 1000-1800 cm⁻¹ and higher I_D/I_G ratio than the untreated films as a result of the appearance of the crystalline graphite structure after the sulfidation treatment. It is showed that the sp² relative content increase in the treated films from the XPS measurement. The Raman results are consistent with the XPS results. The tribological properties of DLC films were investigated using a ball-on-disk rotating friction and wear tester under dry friction conditions. It is found that the sulfidation concentration plays an important part in the tribological properties of the treated DLC films. The results showed the treated films with low sulfidation concentration have a lower friction coefficient (0.1) than the treated films with high sulfidation concentration (0.26) and the untreated films (0.27) under the same friction testing conditions, which can be attributed to both the presence of sulfur-containing materials and the forming of the mechanical alloyed layer on the wear surface. Adding the dry nitrogen to the sliding surface in the testing system helps the friction coefficient of the treated films with low sulfidation concentration to decrease to 0.04 further in this work. On the basis of the experimental results, it is indicated that the liquid sulfidation technique, which is low-cost, non-polluting and convenience, would be an appropriate method for the surface treatment of DLC films.     

Effect of substrates on the properties of p-type ZnO films

Influence of substrates on the properties of p-type ZnO films, which were fabricated by N–Al co-doping technique, was studied. Hall measurement results indicated that ZnO films deposited on common glass substrate were p-type conductivity when Zn:N:Al atomic ratio amounts to 1:3:0.1. However, ZnO films deposited on corning 7059 glass substrate showed n-type conductivity. Secondary ion mass spectroscopy demonstrated that Na content incorporated into ZnO films deposited on common glass substrate was more evident than that of corning 7059 glass. In addition, Hall mobility and conductivity of p-type ZnO thin films deposited on silicon substrate were improved largely.     

Influence of oxygen-plasma posttreatment on the properties of SiO2 films prepared by the electron-beam evaporation method

SiO₂ films were deposited on K9 substrate by the electron-beam evaporation method. The influence of oxygen-plasma posttreatment on the properties of SiO₂ films was investigated. After oxygen-plasma treatment, it was found that the microdefect density of films reduced. We deduced that the absorption of films also reduced. The treated sample exhibited higher LIDT value compared with the as-deposited sample. However, this study is the preliminary work and optimization by this method will be discussed in our future work.     

Study of the effect of the oxygen partial pressure on the properties of rf reactive magnetron sputtered tin-doped indium oxide films

The influence of the oxygen partial pressure on the properties of indium tin oxide films deposited by rf reactive magnetron sputtering has been studied. The oxygen partial pressure was varied from 3.2 × 10⁻⁴ to 1.0 × 10⁻³ mbar. It has been found that the 4 × 10⁻⁴ mbar of oxygen partial pressure is a critical point. When the oxygen partial pressure is lower than 4 × 10⁻⁴ mbar, the deposition rate of the films is high; the films have low transmittance and electrical resistivity; the X-ray diffraction shows that the films have a random orientation and the images of the scanning electron microscopy show that the films surface are smooth without structure. When the pressure is higher than 4 × 10⁻⁴ mbar, the deposition rate is low and does not change as the oxygen partial pressure is further increased; the transmittance and the electrical resistivity are both high; the films show the preferred orientation along the (440) direction; the films surface show a clear structure and as the pressure is increased further, the films become porous. Considering both the factor of transmittance and resistivity, the optimum oxygen partial pressure will be 3.6 × 10⁻⁴ mbar. The films prepared at this pressure have 80% transmittance and 9 × 10⁻⁴ Ω cm resistivity.     

Influence of films thickness and structure on the photo-response of ZnO films

ZnO thin films were grown using Successive Ionic Layer Adsorption and Reaction (SILAR) method on glass substrates at room temperature. Annealing temperatures and film thickness effect on the structural, morphological, optical and electrical properties of the films were studied. For this as-deposited films were annealed at 200, 300, 400 and 500 °C for 30 min in oxygen atmosphere. The X-ray diffraction (XRD) and scanning electron microscopy (SEM) studies showed that the films are covered well with glass substrates and have good polycrystalline structure and crystalline levels. The film thickness effect on band gap values was investigated and band gap values were found to be within the range of 3.49-3.19 eV. The annealing temperature and light effect on electrical properties of the films were investigated and it was found that the current increased with increasing light intensity. The resistivity values were found as 10⁵ Ω-cm for as-deposited films from electrical measurements. The resistivity decreased decuple with annealing temperature and decreased centuple with light emission for annealed films.     

Influence of surface properties on the structure of granular silver films and excitation of localized plasmons

Granular silver films deposited on a thin insulating film of amorphous hydrogenated carbon (a-C:H) and transparent conducting electrode (polycrystalline indium tin oxide (ITO) layer) have been investigated by spectroscopy and microscopy methods. The extinction spectra of silver films on the surface of these materials are found to be significantly different. An annealing of silver films causes a blue shift of the peak of plasmon resonance band in the spectrum of silver nanoparticles: by 16 nm on the a-C:H surface and by 94 nm on the ITO surface. Silver films on the surface of a-C:H films are characterized by a narrower band in the extinction spectrum, which is peaked at 446 nm. The changes observed in the optical density of Ag films are related to the change in size and area of nanoparticles. The results of spectral studies of Ag films are in agreement with the data on the nanostructure obtained by scanning electron microscopy and statistical image processing. The spectra of granular silver films are shown to correlate well with the nanoparticle distribution function over the film area.     

蒸发条件对碘化铅多晶薄膜结构的影响

采用真空蒸发法在普通玻璃上制备了PbI₂多晶薄膜.研究了蒸发速率、蒸发源与衬底距离、薄膜厚度以及衬底温度等实验条件对所制备PbI₂多晶薄膜结构的影响.利用X射线衍射仪和扫描电子显微镜对样品进行了测试.结果表明，在衬底温度为室温时得到(001)择优取向的多晶PbI₂薄膜，即沿c轴垂直衬底方向取向生长的薄膜.当衬底温度升高时，薄膜的择优取向逐渐由(001)转向(003)，且晶体颗粒变大.薄膜中的内应力随衬底温度的升高而降低.     

Effect of the growth conditions on the structural properties of CuInSe2 thin films obtained by the technique of close spaced vapor transport

Thin films of polycrystalline CuInSe₂ were deposited on Pyrex substrates using a simple system of close spaced vapor transport (CSVT). The used CSVT system is an open horizontal reactor, this does not require vacuum, a gas flow is enough. During the growth phase, the CSVT system is continuously crossed by argon gas. A study on the influence of the source temperature and the deposition duration on the structural properties of the deposited films is reported. Analyses by X-ray diffraction have shown that these films are polycrystalline and have a chalcopyrite structure. The preferential orientation of the (112) plane was obtained for the films deposited at 550 ^°C. From the X-ray spectra we calculated the lattice parameters a and c, the ratio c/a was found to be close to 2. The characterization of the deposited films by an energy dispersion spectrometer (EDS) has shown that their chemical composition is quasistoichiometric with a ratio Cu/In varying from 0.96 to 1.10. Analysis with a scanning electron microscope (SEM) of the deposited films surface has shown that those slightly rich in indium present a more homogeneous morphology and smaller crystallites sizes than the films slightly rich in copper. The measurement of the photoconductivity of the prepared compound has allowed us to determine the value of its gap at room temperature. It was found to be close to 0.99 eV.     

The effect of low-energy ion bombardment on the density and crystal structure of thin films

The effect of low-energy ion bombardment on the growth and properties of thin films deposited by rf plasma sputtering at low substrate temperatures is studied. The dependences of the film thickness, density, crystal structure, and conductivity on the bias voltage applied to the substrate are obtained. At biases ranging from 0 to −30 V, nickel films are polycrystalline; at higher biases, they exhibit axial (111) texture. At the bias −60 V, the density of the Ni films is close to that of the bulk metal and the crystal structure of the films is the most ordered. With a further increase in the bias, the density of the films drops because of gas (argon and residual gases) atoms incorporated into the films. The same bias dependence of the density is observed for amorphous films of binary alloys of d and f metals. In this case, the films deposited at the substrate bias −40 V have the highest density.     

Effects of annealing time on infrared emissivity of the Pt film grown on Ni alloy

Platinum films were sputter-deposited on polished nickel alloy substrates. The platinum thin films were applied to serve as low-emissivity layers to reflect thermal radiation. The platinum-coated samples were then heated in the air at 600 °C to explore the effects of annealing time on the emissivity of platinum films. The results show that the grain size of the Pt films increased with the increasing annealing time while their dc electrical resistivity decreased. Besides, the IR emissivitiy of the films gradually decreased with the increasing annealing time. Especially, when the annealing time reached 150 h, the average IR emissivity at the wavelength of 3-14 μm was only about 0.1. Moreover, the chemical analysis indicated that the Pt films on Ni-based alloy exhibit a good resistance against oxidation at 600 °C.     

Optical transmittance and microgravimetric studies of the oxidation of 〈100〉 single crystal films of copper

Thin single crystal copper films have been grown and oxidized on (100) faces of cleaved sodium chloride discs suspended from a vacuum ultramicrobalance. Optical transmittance measurements between 400–800 nm and electron microscopic investigations were also used to characterize the oxidation process. Polycrystalline copper films grown at room temperature are substantially the same as those grown previously on glass substrates. Single crystalline growth at 325 ° C on rock salt produces a characteristic transmittance curve due to the “island” nature of the films. These curves compare favorably with other previously published results. Single crystal copper films oxidized to CuO_0.67 at temperatures of 117–159°C in 100 Torr of oxygen for films less than 500 A thick. For films 378 to 1000 Å thick, compositions of CuO_0.52 to CuO_0.62 were obtained between 123–176°C. The oxidation to less than CuO_0.67 is attributed to the existence of islands in these films which are thicker than the average film thickness, and require higher temperatures or thinner films to permit oxidation to CuO_0.67 before the nucleation of CuO sets in.     

Effects of electron irradiation on the properties of GZO films deposited with RF magnetron sputtering

Transparent conductive GZO films were deposited on polycarbonate substrates by electron beam assisted radio frequency (RF) magnetron sputtering and then the influence of electron irradiation on the structural, optical and electrical properties of GZO films was investigated by using X-ray diffractometry, UV-vis spectrophotometry, four point probes, atomic force microscopy and UV photoelectron spectroscopy. Sputtering power was kept constant at 3 W/cm² during deposition, while electron irradiation energy varied from 450 to 900 eV.Electron irradiated GZO films show larger grain sizes than those of films prepared without electron irradiation, and films irradiated at 900 eV show higher optical transmittance in the visible wavelength region and lower sheet resistance (120 Ω/□) than other films. The work-function is also increased with electron irradiation energy. The highest work-function of 4.4 eV was observed in films that were electron irradiated at 900 eV.