Ge4+、Sn4+掺杂尖晶石LiMn2O4的合成与电化学表征

使用Ge⁴⁺、Sn⁴⁺作为掺杂离子, 通过高温固相法制备四价阳离子掺杂改性的尖晶石LiMn₂O₄材料. X射线衍射(XRD)和扫描电子显微镜(SEM)分析表明, Ge⁴⁺离子取代尖晶石中Mn⁴⁺离子形成了LiMn_2-xGe_xO₄ (x=0.02,0.04, 0.06)固溶体; 而Sn⁴⁺离子则以SnO₂的形式存在于尖晶石LiMn₂O₄的颗粒表面. Ge⁴⁺离子掺入到尖晶石LiMn₂O₄材料中, 抑制了锂离子在尖晶石中的有序化排列, 提高了尖晶石LiMn₂O₄的结构稳定性; 而在尖晶石颗粒表面的SnO₂可以减少电解液中酸的含量, 抑制酸对LiMn₂O₄活性材料的侵蚀. 恒电流充放电测试表明, 两种离子改性后材料的容量保持率均有较大幅度的提升, 有利于促进尖晶石型LiMn₂O₄锂离子电池正极材料的商业化生产.     

石墨烯/尖晶石LiMn2O4纳米复合材料制备及电化学性能

采用溶胶凝胶法和还原氧化石墨法制备尖晶石LiMn2O4纳米晶和石墨烯纳米片,并采用冷冻干燥法制备了石墨烯/尖晶石LiMn2O4纳米复合材料,利用XRD、SEM、AFM等对其结构及表面形貌进行表征;利用CV、充放电、EIS研究纳米复合材料的电化学性能和电极过程动力学特征。结果表明:纳米LiMn2O4电极材料及其石墨烯掺杂纳米复合材料的放电比容量分别为107.16 mAh.g-1,124.30 mAh.g-1,循环100周后,对应容量保持率为74.31%和96.66%,石墨烯可显著改善尖晶石LiMn2O4电极材料的电化学性能,归结于其良好的导电性。纳米复合材料EIS上感抗的产生与半导体尖晶石LiMn2O4不均匀地分布在石墨烯膜表面所造成局域浓差有关,并提出了感抗产生的模型。     

Comparison of structure and electrochemical properties for 5 V LiNi0.5Mn1.5O4 and LiNi0.4Cr0.2Mn1.4O4 cathode materials

Spinel LiNi_0.5Mn_1.5O₄ and LiMn_1.4Cr_0.2Ni_0.4O₄ cathode materials have been successfully synthesized by the sol–gel method using citric acid as a chelating agent. The structure and electrochemical performance of these as-prepared powders have been characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), and the galvanostatic charge–discharge test in detail. XRD results show that there is a small Li _y Ni_1-y O impurity peak placed close to the (4 0 0) line of the spinel LiNi_0.5Mn_1.5O₄, and LiMn_1.4Cr_0.2Ni_0.4O₄ has high phase purity, and the powders are well crystallized. SEM indicates that LiMn_1.4Cr_0.2Ni_0.4O₄ has a slightly smaller particle size and a more regular morphological structure with narrow size distribution than those of LiNi_0.5Mn_1.5O₄. Galvanostatic charge–discharge testing indicates that the initial discharge capacities of LiMn_1.4Cr_0.2Ni_0.4O₄ and LiNi_0.5Mn_1.5O₄ cycled at 0.15 C are 129.6 and 130.2 mAh g⁻¹, respectively, and the capacity losses compared to the initial value, after 50 cycles, are 2.09% and 5.68%, respectively. LiMn_1.4Cr_0.2Ni_0.4O₄ cathode has a higher electrode coulombic efficiency than that of the LiNi_0.5Mn_1.5O₄ cathode, implying that Ni and Cr dual substitution is beneficial to the reversible intercalation and de-intercalation of Li⁺.     

Synthesis of Single‐Crystalline Spinel LiMn2O4 Nanorods for Lithium‐Ion Batteries with High Rate Capability and Long Cycle Life

The long‐standing challenge associated with capacity fading of spinel LiMn₂O₄ cathode material for lithium‐ion batteries is investigated. Single‐crystalline spinel LiMn₂O₄ nanorods were successfully synthesized by a template‐engaged method. Porous Mn₃O₄ nanorods were used as self‐sacrificial templates, into which LiOH was infiltrated by a vacuum‐assisted impregnation route. When used as cathode materials for lithium‐ion batteries, the spinel LiMn₂O₄ nanorods exhibited superior long cycle life owing to the one‐dimensional nanorod structure, single‐crystallinity, and Li‐rich effect. LiMn₂O₄ nanorods retained 95.6 % of the initial capacity after 1000 cycles at 3C rate. In particular, the nanorod morphology of the spinel LiMn₂O₄ was well‐preserved after a long‐term cycling, suggesting the ultrahigh structural stability of the single crystalline spinel LiMn₂O₄ nanorods. This result shows the promising applications of single‐crystalline spinel LiMn₂O₄ nanorods as cathode materials for lithium‐ion batteries with high rate capability and long cycle life.     

尖晶石型LiMn2-xInxO4(x=0，0.01，0.02，0.05)的合成及电化学性能研究

以醋酸锰、氢氧化锂和三氧化二铟为原料,以柠檬酸为配位剂,采用溶胶-凝胶法制备了掺杂In的尖晶石LiMn2-xInxO4(x=0,0.01,0.02,0.05),采用XRD、SEM对目标材料进行了结构和形貌表征,采用恒流充放电、循环伏安(CV)以及交流阻抗(EIS)谱测试对材料进行了电化学性能表征,考察了不同In掺杂量对材料性能的影响。结果表明,当In掺杂量为1%时,LiMn1.99In0.01O4样品具有纯的尖晶石锰酸锂结构,在0.5C和3.4～4.35 V电压范围条件下,LiMn1.99In0.01O4的初始放电容量为119.9 mAh.g-1,经过1C 30次,2C 30次,再0.5C 5次循环后,其放电容量保持率为84.9%,显示了良好的电化学性能。掺杂1%的In的样品比未掺杂的样品具有更优的高温循环稳定性能。     

Enhancing the Electrochemical Performance of the LiMn2O4 Hollow Microsphere Cathode with a LiNi0.5Mn1.5O4 Coated Layer

Spinel cathode materials consisting of LiMn₂O₄@LiNi_0.5Mn_1.5O₄ hollow microspheres have been synthesized by a facile solution‐phase coating and subsequent solid‐phase lithiation route in an atmosphere of air. When used as the cathode of lithium‐ion batteries, the double‐shell LiMn₂O₄@LiNi_0.5Mn_1.5O₄ hollow microspheres thus obtained show a high specific capacity of 120 mA h g^?1 at 1 C rate, and excellent rate capability (90 mAhg^?1 at 10 C) over the range of 3.5–5 V versus Li/Li⁺ with a retention of 95 % over 500 cycles.     

Zur Kinetik der Spinellbildung von β-Ga2O3 mit zweiwertigen Oxiden II. Tracerdiffusion von 63Ni2+ und 67Ga3+ im Nickel-Gallium-Spinell

The self-diffusion coefficients of ⁶³Ni²⁺ and ⁶⁷Ga³⁺ have been measured in nickel-gallium spinels of the general formula $\text{Ni}{}_{\mathrm{1?y}}\text{Ga}{}_{\mathrm{<mtext>2+</mtext><mtext>2y</mtext><mtext>3</mtext>}}\text{O}{}_4$ between 1653 and 1838 K using the restactivity method. Thin radioactive oxide layers are produced on inactive sample surfaces by sedimentation from aqueous solution. The sample composition corresponds to the solubility limit of NiO, respectively, β-Ga₂O₃ in the spinel lattice.It has been concluded that diffusion of Ni²⁺-and Ga³⁺-ions occurs via vacant cation sites.The values obtained for the two cations, which are in the same order of magnitude, are used to calculate the rational reaction constants for NiGa₂O₄ formation after Schmalzried.There is a satisfying agreement between these reaction constants and those values determined by thickness measurement of spinel reaction layers; the agreement between values of activation energy is very good.It is suggested that NiGa₂O₄ formation proceeds after the Wagner mechanism of counterdiffusion of cations.     

KCl熔盐法制备LiMn2O4

采用熔盐法合成了LiMn₂O₄。熔盐的使用可以使原来固相反应的高温焙烧时间缩短。合成获得的材料结晶良好，颗粒大小在数百个纳米左右，有较明显的团聚现象。该材料的初始容量为113 mAh·g^-1，循环性能优良，前100次的容量平均衰减率在0.05%左右；倍率性能亦非常优秀，8 C放电时的容量为1 C放电容量的93%以上。熔盐的用量在4倍于Li⁺以上时，对材料的结构形貌和性能都没有明显影响。     

尖晶石LiMn2O4高温电化学容量衰减及改进

综述了高温下尖晶石LiMn2O4容量衰减的原因、机理研究和改进它的高温性能的方法以及目前的进展,且指出了可能的提高它的高温性能的途径。     

ZrO2- and Li2ZrO3-stabilized spinel and layered electrodes for lithium batteries

Strategies for countering the solubility of LiMn₂O₄ (spinel) electrodes at 50 °C and for suppressing the reactivity of layered LiMO₂ (M=Co, Ni, Mn, Li) electrodes at high potentials are discussed. Surface treatment of LiMn₂O₄ with colloidal zirconia (ZrO₂) dramatically improves the cycling stability of the spinel electrode at 50 °C in Li/LiMn₂O₄ cells. ZrO₂-coated LiMn_0.5Ni_0.5O₂ electrodes provide a superior capacity and cycling stability to uncoated electrodes when charged to a high potential (4.6 V vs Li⁰). The use of Li₂ZrO₃, which is structurally more compatible with spinel and layered electrodes than ZrO₂ and which can act as a Li⁺-ion conductor, has been evaluated in composite 0.03Li₂ZrO₃ · 0.97LiMn_0.5Ni_0.5O₂ electrodes; glassy Li_xZrO_2 + x/2 (0<x⩽2) products can be produced from colloidal ZrO₂ for surface coatings.     

Characterizations of self-combustion reactions (SCR) for the production of nanomaterials used as advanced cathodes in Li-ion batteries

In this work, self-combustion reactions (SCR) for the preparation of important cathode materials for rechargeable Li-ion batteries were investigated by thermal analytical tools (DSC, ARC, TGA), electron microscopy, XRD, various spectroscopies (MS, Raman, FTIR) and elemental analysis by ICP. The systems studied include solutions containing metal nitrates at the right stoichiometry and sucrose as a fuel, for the preparation of LiMn_0.5Ni_0.5O₂ (layered), LiMn_1.5Ni_0.5O₄ (spinel), LiMn_0.33Ni_0.33Co_0.33O₂ (layered), and LiMn_0.4Ni_0.4Co_0.2O₂ (layered). Similar products, which do not depend on the atmosphere of the processes (air or inert) were obtained by spontaneous SCR and the gradual heating of the same solutions by DSC, ARC, and TGA. The reactions involve the partial caramelization of sucrose, complicated by red-ox reactions with the nitrates that form solid products, whose organic part is finally decomposed around 400 °C. The presence of cobalt ions has a stabilizing effect, which is expressed by the low dissolution rates of Li ions from the solid products thus formed, into aqueous solutions. The reaction mechanisms are discussed herein.     

锂离子电池正极材料LiMn2O4的低热固相合成与性能表征

锂离子电池具有比能量高、环境污染小等优点,广泛应用于手提电话、便携式电脑、摄像机等设备中。其正极材料的研究是锂离子电池的研究重点。层状结构的LiCoO2、LiNiO2和尖晶石结构的LiMn2O4是仅有的三种能在3.5V以上电位可嵌入Li的正极材料[1~3]。目前市售的锂离子电池主要采用LiCoO2作正极材料,但由于Co资源缺乏和价格相对昂贵,而锰资源丰富,价格低廉且无毒,对环境友好,因此世界各国都在大力进行以LiMn2O4为正极材料的锂离子电池的实用化研究。LiMn2O4传统的制备方法是高温固相反应合成法[4~7],但由于Mn的变价多,与Li形成贫Li或…     

High-temperature combustion synthesis and electrochemical characterization of LiNiO2, LiCoO2 and LiMn2O4 for lithium-ion secondary batteries

Lithium nickelate (Li_0.88Ni_1.12O₂), lithium cobaltate (LiCoO₂) and lithium manganate (LiMn₂O₄) were synthesized by fast self-propagating high-temperature combustion and their phase purity and composition were characterized by X-ray diffraction and inductively coupled plasma spectroscopy. The electrochemical behaviour of these oxides was investigated with regard to potential use as cathode materials in lithium-ion secondary batteries. The cyclic voltammograms of these cathode materials recorded in 1 M LiClO₄ in propylene carbonate at scan rates of 0.1 and 0.01 mV s^–1 showed a single set of redox peaks. Charge-discharge capacities of these materials were calculated from the cyclic voltammograms at different scan rates. The highest discharge capacity was observed in the case of Li_0.88Ni_1.12O₂. In all the cases, at a very slow scan rate (0.01 mV s^–1) the capacity of the charging (oxidation) process was higher than the discharging (reduction) process. A strong influence of current density on the charge-discharge capacity was observed during galvanostatic cycling of Li_0.88Ni_1.12O₂ and LiMn₂O₄ cathode materials. LiMn₂O₄ can be used as cathode material even at higher current densities (1.0 mA cm^–2), whereas in the case of Li_0.88Ni_1.12O₂ a useful capacity was found only at lower current density (0.2 mA cm^–2). For the fast estimation of the cycling behaviour of LiMn₂O₄, a screening method was used employing a simple technique for immobilizing microparticles on an electrode surface. Electronic Publication     

纯相和镍取代的Co_3O_4尖晶石催化剂用于N_2O直接分解(英文)

A series of NixCo1-xCo2O4(0 ≤ x ≤ 1) spinel catalysts were prepared by the co-precipitation method and used for direct N2O decomposition. The decomposition pathway of the parent precipitates was characterized by thermal analysis. The catalysts were calcined at 500 °C for 3 h and characterized by powder X-ray diffraction, Fourier transform infrared, and N2 adsorption-desorption. Nickel cobaltite spinel was formed in the solid state reaction between NiO and Co3O4. The N2O decomposition measurement revealed significant increase in the activity of Co3O4 spinel oxide catalyst with the partial replacement of Co2+ by Ni2+. The activity of this series of catalysts was controlled by the degree of Co2+ substitution by Ni2+, spinel crystallite size, catalyst surface area, presence of residual K+, and calcination temperature.     

锂离子电池镍掺杂尖晶石LiMn2O4正极材料的电子结构

采用密度泛甬平面波赝势方法对LiMn2O4和LiNi0.5Mn1.5O4的几何结构进行了优化,并计算了相应的电子结构.计算的结果表明:在Li 脱嵌前后,LiMn2O4和LiNi0.5Mn1.5O4均为导体,且锂元素主要以离子形式存在于两种材料中,O2p轨道与Mn(Ni)的3d轨道形成了较强的共价键.Li 嵌入导致Mn(Ni)3d轨道的态密度峰发生移动.Ni的掺杂导致Mn(Ni)和O2p轨道的成键作用得以加强,电子在Mn(Ni)3d轨道的填充发生变化,从而提高了电池的充放电电压.     

NMR and FT-IR Investigation of Spinel LiMn2O4 Cathode Prepared by the Tartaric Acid Gel Process

The structure of the lithium manganese tartrate precursor and the synthesis mechanism of LiMn₂O₄ were investigated by FT-IR, NMR, TG/DSC, and XRD in this study. The results of FT-IR and ⁷Li and ¹³C NMR measurements revealed that lithium ions bond with carboxylic acid ligands and the O–H stretching modes of tartaric acid. Manganese ion bonds only with carboxylic acid. Lithium and manganese ions were trapped homogeneously on an atomic scale throughout the precursor. Such a structure eliminates the need for long-range diffusion during the formation of lithium manganese oxides. Therefore, spinel LiMn₂O₄ was synthesized at temperatures as low as 300°C. In this work, the electrochemical properties of Li/Li_xMn₂O₄ were studied. It is clear that the discharge curves exhibit two pseudo plateaus as the LiMn₂O₄ is fired to higher temperatures. The discharge capacity of LiMn₂O₄ increases from 84 to 117 mAh/g as the calcination temperature increases from 300 to 500°C. The LiMn₂O₄ powders calcined at low temperatures with a high specific surface area and an average valence of manganese exhibit a better cycle life.     

球形尖晶石LiMn2O4掺杂钇的性能研究

利用控制结晶方法, 在前驱体碳酸锰中共沉淀掺杂适量的钇, 得到球形掺杂钇的碳酸锰, 在540 ℃预烧后, 与锂盐一起焙烧, 可以得到高活性的掺钇球形尖晶石LiMn₂O₄. XRD分析表明, 产物中无杂相产生. 研究表明, 掺杂钇与掺杂其它金属离子的特性不一样, 钇具有催化特性, 掺杂钇可以提高尖晶石LiMn₂O₄中锰的活性. 掺钇使得更多的Mn^3＋参加电化学反应, 增加容量; 但同时也使更多的锰与电解液反应, 造成锰的溶解, 容量损失. 掺钇量越多, 锰的溶解量越大. 因此, 合适的掺杂量对于保证产品良好的电化学性能至关重要. 实验证明, 掺钇0.5%的产品Li(Y_0.005Mn_0.995)₂O₄具有较好的电化学性能. 其常温初始比容量为130 mAh•g^－1, 大于纯相的锰酸锂的125 mAh•g^－1, 100次循环后比容量为120 mAh•g^－1, 容量保持率为92.3%.     

The electrochemical performance of sodium-ion-modified spinel LiMn2O4 used for lithium-ion batteries

The spinel LiMn₂O₄ cathode material has been considered as one of the most potential cathode active materials for rechargeable lithium ion batteries. The sodium-doped LiMn₂O₄ is synthesized by solid-state reaction. The X-ray diffraction analysis reveals that the Li_1?x Na _x Mn₂O₄ (0?≤?x?≤?0.01) exhibits a single phase with cubic spinel structure. The particles of the doped samples exhibit better crystallinity and uniform distribution. The diffusion coefficient of the Li_0.99Na_0.01Mn₂O₄ sample is 2.45?×?10^?10 cm^?2 s^?1 and 3.74?×?10^?10 cm^?2 s^?1, which is much higher than that of the undoped spinel LiMn₂O₄ sample, indicating the Na⁺-ion doping is favorable to lithium ion migration in the spinel structure. The galvanostatic charge–discharge results show that the Na⁺-ion doping could improve cycling performance and rate capability, which is mainly due to the higher ion diffusion coefficient and more stable spinel structure.     

Zur Kinetik der Spinellbildung von β-Ga2O3 mit zweiwertigen Oxiden. I. Die Festkörperreaktion von β-Ga2O3 mit NiO

The solid state reaction in a sandwich type diffusion couple of NiO and β-Ga₂O₃ has been investigated between 1240 and 1550°C in air and inert gas atmosphere.Optical microscope and X-ray methods are used to identify the reaction product, which is a singlephased spinel of the general formula $\text{Ni}{}_{\mathrm{1?y}}\text{Ga}{}_{\mathrm{<mtext>2+</mtext><mtext>2y</mtext><mtext>3</mtext>}}\text{O}{}_4$. The homogeneity range of the spinel phase was investigated by X-ray methods; there is a high solubility of β-Ga₂O₃ in the spinel lattice.The growth of the thickness of the reaction layer follows a parabolic rate law, and therefore a diffusion process must be rate determining. The activation energy of the rate controlling step is 82 kcal/mole.Pt-marker experiments are not sufficient for determining the reaction mechanism. Investigations with an electron-probe microanalyzer, an connection with a modified marker technique, resulted in a Wagner-mechanism of counterdiffusion of cations for formation of nickel-gallium spinel; the total amount in Ga³⁺ ions is lost for spinel formation before there is an appreciable solubility of gallium in NiO.     

LiCoO2对LiMn2O4改性过程的研究

在LiCoO2、LiMn2O4、LiNiO2这三种锂离子电池正极材料中,尖晶石LiMn2O4由于具有价廉、对环境友好、使用安全的显著优点,被普遍认为是最有希望的新型正极材料。但该材料在高温下较快的容量衰减制约了其规模应用[1~3]。为改善LiMn2O4的高温性能,各国学者普遍采用掺杂法,即在制备L