阴离子型接枝微粒PDAC/PSA的制备及对谷氨酸的吸附性能初探

采用自由基聚合法在溶液聚合体系中将功能单体丙烯酰氧乙基三甲基氯化铵(DAC)接枝于聚苯乙烯伯胺微球(PSA)表面,制备了接枝微粒PDAC/PSA,考察了主要因素对接枝聚合的影响,并初步探究了其对L-谷氨酸的吸附特性。结果表明,在反应温度25℃、单体质量分数为6%、引发剂占单体质量的1.2%的条件下,可制得接枝度为431mg/g的接枝微粒,其对L-谷氨酸的吸附量达140mg/g。     

To patterned binary polymer brushes via capillary force lithography and surface-initiated polymerization

An effective approach is described for the synthesis of binary patterned polymer brushes using a combination of capillary force lithography and surface-initiated polymerization. First, the approach calls for an ultrathin polystyrene (PS) mask to be deposited, in a pattern, over a surface to which a layer of polymerization initiator has already been anchored. Next, surface-initiated atom transfer radical polymerization (ATRP) is performed. This can graft the initial polymer brush onto those areas of the surface unprotected by the PS mask. After grafting is complete, the PS mask is removed and a second brush is synthesized on the newly exposed areas.     

Controlled nitroxide-mediated styrene surface graft polymerization with atmospheric plasma surface activation

Polymer layer growth by free radical graft polymerization (FRGP) and controlled nitroxide-mediated graft polymerization (NMGP) of polystyrene was achieved by atmospheric pressure hydrogen plasma surface activation of silicon. Kinetic polystyrene layer growth by atmospheric pressure plasma-induced FRGP (APPI-FRGP) exhibited a maximum surface-grafted layer thickness (125 A after 20 h) at an initial monomer concentration of [M] 0 = 2.62 M at 85 degrees C. Increasing both the reaction temperature ( T = 100 degrees C) and initial monomer concentration ([M] 0 = 4.36 M) led to an increased initial film growth rate but a reduced polymer layer thickness, due to uncontrolled thermal initiation and polymer grafting from solution. Controlled atmospheric pressure plasma-induced NMGP (APPI-NMGP), using 2,2,6,6-tetramethyl-1-piperidinyloxy (TEMPO), exhibited a linear increase in grafted polystyrene layer growth with time due to controlled surface graft polymerization as well as reduced uncontrolled solution polymerization and polymer grafting, resulting in a polymer layer thickness of 285 A after 60 h at [TEMPO] = 10 mM, [M] 0 = 4.36 M, and T = 120 degrees C. Atomic force microscopy (AFM) surface analysis demonstrated that polystyrene-grafted surfaces created by APPI-NMGP exhibited a high surface density of spatially homogeneous polymer features with a low root-mean-square (RMS) surface roughness ( R rms = 0.36 nm), similar to that of the native silicon surface ( R rms = 0.21 nm). In contrast, polymer films created by APPI-FRGP at [M] 0 = 2.62 M demonstrated an increase in polymer film surface roughness observed at reaction temperatures of 85 degrees C ( R rms = 0.55 nm) and 100 degrees C ( R rms = 1.70 nm). The present study concluded that the current approach to APPI controlled radical polymerization may be used to achieve a grafted polymer layer with a lower surface roughness and a higher fractional coverage of surface-grafted polymers compared to both conventional FRGP and APPI-FRGP.     

GRAFTING OF POLYSTYRENE ONTO A NANOMETER SILICA SURFACE BY MICROEMULSION POLYMERIZATION

The grafting of polystyrene onto a nanometer silica surface by microemulsion polymerization is described. Silicawas functionalized with 3-methacryloxypropyltrimethoxysilane coupling agent before polymerization. A mixture of ionic andnon-ionic surfactants as well as water-soluble and oil-soluble initiators were used. The effect of the amount of silica and ionicsurfactant on the graft polymerization was studied. The graft polymerization procedure for styrene was also applied to methylmethacrylate. Composite particles with a core-shell structure were obtained and the yield and grafting efficiency of monomerwere high.     

Direct observation of the phase transition for a poly(N-isopropylacryamide) layer grafted onto a solid surface by AFM and QCM-D

The temperature-induced structural changes of a thermo-responsive poly(N-isopropylacrylamide) (PNIPAM) layer grafted onto a silica substrate were investigated in aqueous solution using an atomic force microscope (AFM) and a quartz crystal microbalance with dissipation (QCM-D). A PNIPAM layer was grafted onto the silicon wafer surface by free radical polymerization of NIPAM to obtain a high molecular weight polymer layer with low-grafting density overall. By AFM imaging, the transition of the grafted PNIPAM chains from a brush-like to a mushroom-like state was clearly visualized: The surface images of the plate were featureless at temperatures below the LCST commensurate with a brush-like layer, whereas above the LCST, a large number of domain structures with a characteristic size of approximately 100 nm were seen on the surface. Both frequency and dissipation data obtained using QCM-D showed a significant change at the LCST. Analysis of these data confirmed that the observed PNIPAM structural transition was caused by a collapse of the brush-like structure as a result of dehydration of the polymer chains.     

Reversible addition–fragmentation chain‐transfer graft polymerization of styrene: Solid phases for organic and peptide synthesis

The γ‐initiated reversible addition–fragmentation chain‐transfer (RAFT)‐agent‐mediated free‐radical graft polymerization of styrene onto a polypropylene solid phase has been performed with cumyl phenyldithioacetate (CPDA). The initial CPDA concentrations range between 1 × 10^?2 and 2 × 10^?3 mol L^?1 with dose rates of 0.18, 0.08, 0.07, 0.05, and 0.03 kGy h^?1. The RAFT graft polymerization is compared with the conventional free‐radical graft polymerization of styrene onto polypropylene. Both processes show two distinct regimes of grafting: (1) the grafting layer regime, in which the surface is not yet totally covered with polymer chains, and (2) a regime in which a second polymer layer is formed. Here, we hypothesize that the surface is totally covered with polymer chains and that new polymer chains are started by polystyrene radicals from already grafted chains. The grafting ratio of the RAFT‐agent‐mediated process is controlled via the initial CPDA concentration. The molecular weight of the polystyrene from the solution (PS_free) shows a linear behavior with conversion and has a low polydispersity index. Furthermore, the loading of the grafted solid phase shows a linear relationship with the molecular weight of PS_free for both regimes. Regime 2 has a higher loading capacity per molecular weight than regime 1. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 4180–4192, 2002     

Synthesis of selenium nano-composite (t-Se@PS) by surface initiated atom transfer radical polymerization

Selenium nanostructures, which are otherwise susceptible to oxidative damage, were encapsulated with a thin layer of polystyrene. The thin layer of polystyrene was grafted onto the surfaces of selenium by a surface initiated atom transfer radical polymerization reaction. These encapsulated nanostructures demonstrate an enhanced resistance towards corrosion.     

活性自由基聚合法制备以C60封端的聚苯乙烯

通过活性自由基聚合的方法制备了以２,２,６,６－四甲基－４－羟基呱啶氮氧自由基（ＴＥＭＰＯＬ）封端的聚苯乙烯大分子,实验结果证明该反应体系是一个典型的活性自由基聚合体系,同时研究了ＴＥＭＰＯＬ／ＡＩＢＮ的比例及ＡＩＢＮ的含量对聚合反应的影响。用以ＴＥＭＰＯＬ封端的聚苯乙烯和Ｃ６０反应,制得了Ｃ６０的聚苯乙烯高分子衍生物,紫外和ＧＰＣ结果均证明Ｃ６０已连接到聚苯乙烯的长链上,ＧＰＣ的结果还证明,Ｃ６     

A versatile method for tuning the chemistry and size of nanoscopic features by living free radical polymerization

A novel approach is presented for manipulating the size and chemistry of nanoscopic features using a combination of contact molding and living free radical polymerization. In this approach a highly cross-linked photopolymer, based on a methacrylate/acrylate mixture, was patterned into submicrometer-sized features on a silicon wafer using a contact-molding technique. A critical component of the monomer mixture was the incorporation of an initiator containing monomer into the network structure, which provides sites for functional group amplification. Features ranging in size from 5 microm to <60 nm were accurately replicated by this process and living free radical polymerizations, both atom transfer radical and nitroxide-mediated polymerization (NMP), could be conducted from these initiating sites to yield polymer brushes which represent a grafted layer of linear chains attached to the original network polymer. Grafts consisting of polystyrene, poly(methyl methacrylate), and poly(2-hydroxyethyl)methacrylate were grown with controlled thicknesses ranging from 10 to 143 nm and graft molecular weights of between 18 000 to 290 000 amu. As a result of this secondary graft process, feature sizes could be tuned from the original 100 nm down to 20 nm, and the surface chemistry varied from hydrophilic to hydrophobic starting from the same initial master pattern. The thin films and patterned features were characterized by contact angle, ellipsometry, optical, and atomic force microscopies.     

Effect of polymerization conditions on the molecular weight of polystyrene grafted onto silica in the radical graft polymerization initiated by azo or peroxyester groups introduced onto the surface

The effect of polymerization conditions on the molecular weight of polystyrene grafted onto silica obtained from the radical graft polymerization initiated by azo and peroxyester groups introduced onto the surface was investigated. The molecular weight of polystyrene grafted onto silica obtained from the radical graft polymerization initiated by surface azo and peroxyester groups decreased with decreasing monomer concentration and polymerization temperature. The molecular weight of polystyrene was found to be controlled to some extent by the addition of a chain transfer agent. The molecular weight of grafted chain on silica surface obtained from the graft polymerization initiated by surface radicals formed by photodecomposition of azo groups was considerably smaller than that by thermal decomposition. The number of grafted polystyrene in photopolymeriztion, however, was much larger than that in thermal polymerization. These results are explained by the blocking of surface radicals formed on the silica surface by previously grafted polymer chain: when the decomposition of surface azo and peroxyester groups proceed instantaneously at the initial stage of the polymerization, the number of grafted polymer chains increased.     

梯度引发自由基聚合体系(Ⅰ)——基原法合成超高分子量聚合物

90年代在自由基聚合基础研究领域的一个重要成是“长 短终止”理论被进一步确认和接受[1 ,2 ] .按照该模型 ,聚合反应中的终止反应主要发生在长链自由基与短链自由基或初级自由基之间 ,即长链自由基之间很难进行终止反应 ,链终止常数随链长增加而急剧下降 .80年代初 ,Ｓｉｍｉｏｎｅｓｃｕ等[3] 曾报道了用等离子体照射封有单体的玻璃管 ,尔后放入暗处聚合的工作 ,发现不仅可得到分子量上千万的聚丙烯酸或聚丙烯酰胺 ,而且聚合活性可保持几十个小时 ;国内学者[4] 利用该法也得到了分子量接近千万的聚丙烯酰胺 .基于这种终止模型和实验结果 ,…     

Model filled polymers. VIII. Synthesis of crosslinked polymeric beads by seed polymerization

Monodisperse crosslinked polystyrene (PS) and polymethacrylate (PMA) beads of sizes greater than 1 μm in diameter are prepared by particle nucleation onto pre-existing polymer seeds in a multistage emulsion polymerization, in the absence of emulsifier. An adequate seed number concentration, which decreases with increasing seed size, is necessary to achieve monodisperse beads. Monodisperse multicomposition beads are prepared by polymerizing styrene onto PMA seeds, but not by polymerizing methyl methacrylate onto PS seeds. Phase separation in growing seed particles or surface polymerization following free radical capture may lead to the formation of asymmetric shaped particles.     

氟碳端基聚合物合成及其表面吸附性能

综述了近十年来氟端基聚合物的合成,表征及其在表面吸附行为的研究成果。通过含有氟烷基的引发剂或终止剂在活性阴离子聚合反应或自由基聚合反应中使聚合物接上氟端基。已经成功地利用活性阴离子聚合反应合成了氟端基聚苯乙烯,通过含氟自由基引发烯类单体（如丙烯酸,乙烯硅等）可在相应聚合物链上引入氟端基,另外,聚合物的化学改性方法也可将氟基团接在聚合物链端（如氟基聚氧乙烯,氟端基聚合物具有的表面活性,当水溶液中或聚     

Characterization of poly(sodium styrene sulfonate) thin films grafted from functionalized titanium surfaces

Biointegration of titanium implants in the body is controlled by their surface properties. Improving surface properties by coating with a bioactive polymer is a promising approach to improve the biological performance of titanium implants. To optimize the grafting processes, it is important to fully understand the composition and structure of the modified surfaces. The main focus of this study is to provide a detailed, multitechnique characterization of a bioactive poly(sodium styrene sulfonate) (pNaSS) thin film grafted from titanium surfaces via a two-step procedure. Thin titanium films (～50 nm thick with an average surface roughness of 0.9 ± 0.2 nm) prepared by evaporation onto silicon wafers were used as smooth model substrates. X-ray photoelectron spectroscopy (XPS) and time-of-flight secondary ion mass spectrometry (ToF-SIMS) showed that the titanium film was covered with a TiO(2) layer that was at least 10 nm thick and contained hydroxyl groups present at the outermost surface. These hydroxyl groups were first modified with a 3-methacryloxypropyltrimethoxysilane (MPS) cross-linker. XPS and ToF-SIMS showed that a monolayer of the MPS molecules was successfully attached onto the titanium surfaces. The pNaSS film was grafted from the MPS-modified titanium through atom transfer radical polymerization. Again, XPS and ToF-SIMS were used to verify that the pNaSS molecules were successfully grafted onto the modified surfaces. Atomic force microscopy analysis showed that the film was smooth and uniformly covered the surface. Fourier transform infrared spectroscopy indicated that an ordered array of grafted NaSS molecules were present on the titanium surfaces. Sum frequency generation vibration spectroscopy and near edge X-ray absorption fine structure spectroscopy illustrated that the NaSS molecules were grafted onto the titanium surface with a substantial degree of orientational order in the styrene rings.     

A surface-reactive rod-coil diblock copolymer: nano- and micropatterned polymer brushes.

A diblock copolymer consisting of poly(3-(triethoxysilyl)propylisocyanate) (PIC) and polystyrene(PS) was synthesized by anionic polymerization. A polymeric monolayer of the block copolymer was formed on silica substrates by various grafting techniques such as immersion, casting, or contact-printing. The PIC block adheres covalently to Si substrates in an in-plane fashion due to its extended rodlike conformation and reactivity to the silica. The polystyrene blocks aggregate to form mounds on the surface resulting in a new type of nanopatterned polymer brush. The self-limiting adsorption of the rod coils results in a thickness of about 5 nm regardless of the solution concentration and coating method. This particular property allowed microcontact printing directly onto silicon or glass substrates. The resulting surface morphology consisted of nanoscale domains given by the block copolymer and uniform thickness micropatterns transferred from the stamp within the printed area. This study offers a simple new method to prepare a covalent polymeric monolayer with nano- and micropatterns, which can be performed directly onto various silicon-based substrates.     

Synthesis of aromatic oxazolyl‐ and carboxyl‐functionalized polymers: Atom transfer radical polymerization of styrene initiated by 2‐[(4‐bromomethyl)phenyl]‐4,5‐dihydro‐4,4‐dimethyloxazole

The synthesis of a new compound, 2‐[(4‐bromomethyl)phenyl]‐4,5‐dihydro‐4,4‐dimethyloxazole ( 1 ), and its utility in the synthesis of oxazoline‐functionalized polystyrene by atom transfer radical polymerization (ATRP) methods are described. Aromatic oxazolyl‐functionalized polymers were prepared by the ATRP of styrene, initiated by ( 1 ) in the presence of copper(I) bromide/2,2′‐bipyridyl catalyst system, to afford the corresponding α‐oxazolyl‐functionalized polystyrene ( 2 ). The polymerization proceeded via a controlled free radical polymerization process to produce the corresponding α‐oxazolyl‐functionalized polymers with predictable number‐average molecular weights, narrow molecular weight distributions in high‐initiator efficiency reactions. Post‐ATRP chain end modification of α‐oxazolyl‐functionalized polystyrene ( 2 ) to form the corresponding α‐carboxyl‐functionalized polystyrene ( 3 ) was achieved by successive acid‐catalyzed hydrolysis and saponification reactions. The polymerization processes were monitored by gas chromatography analyses. The unimolecular‐functionalized initiator and functionalized polymers were characterized by thin layer chromatography, spectroscopy, size exclusion chromatography, and nonaqueous titration analysis. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011.     

“Living” radical graft polymerization of styrene to styrene butadiene rubber (SBR) with 2,2,6,6‐tetramethyl‐1‐piperidinyloxy (TEMPO)

Well‐defined graft copolymers with styrene butadiene rubber (SBR) backbones and polystyrene branches were synthesized by living free radical polymerization (LFRP) techniques. Thus 1‐ benzoyl‐2‐phenyl‐2‐(2′,2′,6′,6′‐tetramethyl‐piperidinyl‐1′‐oxy)ethane (BZ‐TEMPO) was synthesized and hydrolyzed to the corresponding 1‐hydroxyl derivative. This functional nitroxyl compound was coupled with brominated SBR (SBR‐Br). The resulting macroinitiator (SBR‐TEMPO) for “living” free radical polymerization was then heated in the presence of styrene for the formation of the controlled graft copolymer. ¹H‐NMR and IR spectroscopy were used to investigate the structure of the polymers. Copyright © 2004 John Wiley & Sons, Ltd.     

Synthesis and Polymerization Kinetics of Polystyrene Grafting using Azo-groups Bounded SiO2 as an Initiator

This work presents a new method for synthesis of inorganic/organic hybrid nanoparticles via the in-situ polymerization by the use of the azo-groups bounded silica nanoparticles as a radical initiator and styrene as a model vinyl-monomer. The synthesis and the structure of silica/polystyrene (SiO₂/PS), and the polymerization kinetics of the styrene initiated by the azo-groups bounded SiO₂ nanoparticles are studied with techniques such as FTIR, XPS, DSC, GPC, and TEM. Results show that the SiO₂-g-PS nanoparticles are synthesized successfully, and the resulting hybrid nanoparticles have a core-shell structure with SiO₂ in the core and the polystyrene on the outside layer. The percentage of the grafted PS on the SiO₂ surface increases with the progress of the polymerization before 6 h, and the largest amount of the grafted PS reaches 33% of the silica nanoparticles.

Consequently, the size of the nanoparticles increases ca. 20 nm upon the polystyrene grafting. The molecular weight of the grafted PS increases with the polymerization, and it has reached a much large value in the first several polymerization hours while it keeps a constant value approximately in the following polymerization process. Meanwhile, the polydispersity index of the grafted PS gradually increases with the progress of the polymerization. These phenomena agree with the theory of the traditional free radical polymerization very well.     

Graft polymerization from pore wall of three-dimensionally ordered macroporous cross-linked polystyrene via atom transfer radical polymerization

The surface-initiated atom-transfer radical polymerization (ATRP) technique was applied to the graft polymerization of methyl methacrylate (MMA) and N-isopropylacrylamide (NIPAm) from three-dimensionally ordered macroporous cross-linked polystyrene (3DOM CLPS) on which the initiator, halogen atom was immobilized onto the pore wall of 3DOM CLPS by chloromethylation. FT-IR and TG-DWA analyses confirm that the graft polymerization of MMA and NIPAm via ATRP had been taken place at the pore wall of 3DOM CLPS. The initiating efficiency of chloromethyl groups was calculated according to the data of TGA-titration, revealed that the benzyl chloride is not only distributed on the surface of the pore walls but also must be present throughout the inner of the cross-linked polystyrene matrix. SEM analyses show that the grafted layers are smooth and homogeneous, and the ordered structure is well preserved after polymerization. By the adjustment of the graft polymerization time, the thickness of grafted polymer layers can be controlled. The max thickness of grafted PMMA layer is 85 nm and the max thickness of grafted PNIPAm layer is 35 nm.     

Grafting of polymers onto and/or from silica surface during the polymerization of vinyl monomers in the presence of γ‐ray‐irradiated silica

The effects of radicals on silica surface, which were formed by γ‐ray irradiation, on the polymerization of vinyl monomers were investigated. It was found that the polymerization of styrene was remarkably retarded in the presence of γ‐ray‐irradiated silica above 60 °C, at which thermal polymerization of styrene is readily initiated. During the polymerization, a part of polystyrene formed was grafted onto the silica surface but percentage of grafting was very small. On the other hand, no retardation of the polymerization of styrene was observed in the presence of γ‐ray‐irradiated silica below 50 °C; the polymerization tends to accelerate and polystyrene was grafted onto the silica surface. Poly(vinyl acetate) and poly(methyl methacrylate) (MMA) were also grafted onto the surface during the polymerization in the presence of γ‐ray‐irradiated silica. The grafting of polymers onto the silica surface was confirmed by thermal decomposition GC‐MS. It was considered that at lower temperature, the grafting based on the propagation of polystyrene from surface radical (“grafting from” mechanism) preferentially proceeded. On the contrary, at higher temperature, the coupling reaction of propagating polymer radicals with surface radicals (“grafting onto” mechanism) proceeded to give relatively higher molecular weight polymer‐grafted silica. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 2972–2979, 2006