A highly selective and sensitive thorium(IV) PVC membrane electrode based on a dithio-tetraaza macrocyclic compound.

A poly(vinyl chloride)-based membrane composed of dithio-tetraaza macrocyclic compound as a neutral carrier with sodium tetraphenylborate (NaTPB) as an anion excluder and nitrobenzene (NB) as plasticizer was prepared and investigated as a Th(IV)-selective electrode. The electrode exhibits a Nernstian slope of 14.2 +/- 0.3 mV per decade over a wide concentration range (1.0 x 10(-6) to 1.0 x 10(-1) M) with a detection limit of 8.0 x 10(-7) M between pH 3.5 and 9.5. The response time of the sensor is about 10 s and it can be used over a period of 5 months without any divergence in potential. The proposed membrane sensor revealed a good selectivity for Th(IV) over a wide variety of other metal ions and proved to be a better electrode in many respects than those reported in the literature. It was successfully applied as an electrode indicator as well as in the direct determination of thorium ions in standard and real samples.     

Nanostructured pure gamma-Fe2O3 via forced precipitation in an organic solvent

Pure maghemite, gamma-Fe(2)O(3), was prepared as ultra fine particles in the nanometer-sized range via the forced precipitation method in an organic solvent. The precipitation of iron(III) ions, from iron(III) chloride in 2-propanol led selectively to highly dispersed particles of ferrihydrite, which upon treatment with temperatures higher than 200 degrees C under dynamic vacuum resulted in high-surface-area particles of gamma-Fe(2)O(3). Precipitation in water also led to ferrihydrite, but the final product, after heating at 300 degrees C, contained a mixture of gamma-Fe(2)O(3) and alpha-Fe(2)O(3) (hematite). The precipitation from iron(III) nitrate in water resulted in goethite which was converted to hematite upon heating. On the other hand, the final product in 2-propanol was a mixture of maghemite and hematite. The products were characterized by FTIR, TGA, XRD, and gas sorption analysis. Nitrogen gas adsorption studies for the pure gamma-Fe(2)O(3) samples revealed mesoporous particles with high surface areas in the range of 70-120 m(2) g(-1) after heat treatment at 300 degrees C. The gamma-Fe(2)O(3) particles retained their gamma-phase as well as their mesoporous structure at relatively high temperatures, as high as 400 degrees C.     

Synthesis of α-Bromine- Terminated Polystyrene Macroinitiator and Its Initiation of MMA Polymerization by ATRP

In the present paper the synthesis of block copolymers via the transformation from living anionic polymerization (LAP) to atom transfer radical polymerization (ATRP) was described. Α-Bromine-terminated polystyrenes(PStBr) in the LAP step was prepared by using n-BuLi as initiator, tetrahydrofuran (THF) as the activator, α-methylstyrene (α-MeSt) as the capping group and liquid bromine (Br2) as the bromating agent. The effects of reaction conditions such as the amounts of α-MeSt, THF, and Br2 as well as molecular weight of polystyrene on the bromating efficiency (BE) and coupling extent (CE) were examined. The present results show that the yield of PStBr obtained was more than 93.8% and the coupling reaction was substantially absent. PStBr was further used as the macroinitiator in the polymerization of methyl-methacrylate(MMA) in the presence of copper(Ⅰ) halogen and 2,2-bipyridine(bpy) complexes. It was found that the molecular weight of the resulted PSt-b-PMMA increased linearly with the increase of the conversion of MMA and the polydispersity was 1.2-1.6. The structures of PStBr and P(St-b-MMA) were characterized by 1H NMR spectra.     

Extraction of lead(II) and copper(II) from salicylate media by tributylphosphine oxide.

Tributylphosphine oxide (TBPO) is proposed as an extractant for the extraction of lead(II) and copper(II) from salicylate media. The optimum conditions were evaluated by varying the experimental parameters, such as the pH, sodium salicylate concentration, tributylphosphine oxide (TBPO) concentration, shaking period and various diluents. The probable extracted species, deduced from log-log plots were Pb(HSal)2.2TBPO and Cu(HSal)2.2TBPO. The extraction took place through a solvation mechanism. The method permits the binary separation of lead(II) and copper(II) from commonly associated elements as well as the mutual separation of lead(II) and copper(II). The method is applicable to the determination of lead(II) and copper(II) in various alloys as well as environmental and pharmaceutical samples.     

Symmetrical and unsymmetrical pincer complexes with group 10 metals: synthesis via aryl C-H activation and some catalytic applications

Aryl-based pincer metal complexes with anionic terdentate ligands have been widely applied in organic synthesis, organometallic catalysis and other related areas. Synthetically, the most simple and convenient method for the construction of these complexes is the direct metal-induced C(aryl)-H bond activation, which can be fulfilled by choosing the appropriate functional donor groups in the two side arms of the aryl-based pincer preligands. In this perspective, we wish to summarize some results achieved by our group in this context. Successful examples include symmetrical chiral bis(imidazoline) NCN pincer complexes with Ni(II), Pd(II) and Pt(II), bis(phosphinite) and bis(phosphoramidite) PCP pincer Pd(II) complexes, unsymmetrical (pyrazolyl)phosphinite, (amino)phosphinite and (imino)phosphinite PCN pincer Pd(II) complexes, chiral (imidazolinyl)phosphinite and (imidazolinyl)phosphoramidite PCN pincer complexes with Ni(II) and Pd(II) as well as unsymmetrical (oxazolinyl)amine and (oxazolinyl)pyrazole NCN' pincer Pd(II) complexes. Among them, the P-donor containing complexes are efficiently synthesized by the "one-pot phosphorylation/metalation" method. The obtained symmetrical and unsymmetrical pincer complexes have been used as catalysts in Suzuki-Miyaura reaction (Pd), asymmetric Friedel-Crafts alkylation of indole with trans-β-nitrostyrene (Pt) as well as in asymmetric allylation of aldehyde and sulfonimine (Pd). In the Suzuki couplings conducted at 40-50 °C, some unsymmetrical Pd complexes exhibit much higher activity than the related symmetrical ones which can be attributed to their faster release of active Pd(0) species resulting from the hemilabile coordination of the ligands. Literature results on the synthesis of some related pincer complexes as well as their activities in the above catalytic reactions are also presented.     

Endohedral nickel and palladium atoms in metal clusters: analogy to endohedral noble gas atoms in fullerenes in polyhedra with five-fold symmetry

Nickel and palladium atoms with their closed-shell d(10) electronic configurations are encapsulated in the icosahedral clusters [Ni@Ni(10)E(2)(CO)(18)](4-)(E = Sb, Bi, Sb[rightward arrow]Ni(CO)(3), CH(3)Sn and n-C(4)H(9)Sn) and the geometrically related pentagonal antiprismatic cluster Pd@Bi(10)(4+) found in Bi(14)PdBr(16). Such endohedral d(10) atoms in pentagonal antiprismatic clusters are donors of zero skeletal electrons and interact only weakly with the atoms in the surrounding polyhedron so that they may be regarded as analogous to endohedral noble gases in fullerenes such as He@C(60). On the other hand, endohedral nickel and palladium atoms in 10- and 11-vertex flattened deltahedral bare metal clusters of group 13 metals without five-fold symmetry, such as Ni@E(10)(10-) found in Na(10)NiE(10)(E = Ga, In) and Pd@Tl(11)(7-) found in A(8)Tl(11)Pd (A = Cs, Rb, K), interact significantly with the cluster atoms, particularly those at the flattened vertices of the deltahedron. The role of endohedral d(10) atoms Ni and Pd in polyhedra with five-fold symmetry as "pseudo-noble-gases" can be related to their positions at the "composite divide" of the "Metallurgists' Periodic Table" proposed by H. E. N. Stone on the basis of alloy systematics as well as the equivalence of the five d orbitals in polyhedra with five-fold symmetry.     

NiN(2)S(2) complexes as metallodithiolate ligands to Rh(I), Rh(II) and Rh(III)

Three molecular structures are reported which utilize the NiN(2)S(2) ligands -, (bis(mercaptoethyl)diazacyclooctane)nickel and -', bis(mercaptoethyl)diazacycloheptane)nickel, as metallodithiolate ligands to rhodium in oxidation states i, ii and iii. For the Rh(I) complex, the NiN(2)S(2) unit behaves as a bidentate ligand to a square planar Rh(I)(CO)(PPh(3))(+) moiety with a hinge or dihedral angle (defined as the intersection of NiN(2)S(2) and S(2)Rh(C)(P) planes) of 115 degrees . Supported by -' ligands, the Rh(II) oxidation state occurs in a dirhodium C(4) paddlewheel complex wherein four NiN(2)S(2) units serve as bidentate bridging ligands to two singly-bonded Rh(II) ions at 2.893(8) A apart. A compilation of the remarkable range of M-M distances in paddlewheel complexes which use NiN(2)S(2) complexes as paddles is presented. The Rh(III) state is found as a tetrametallic [Rh(-')(3)](3+) cluster, roughly shaped like a boat propeller and structurally similar to tris(bipyridine)metal complexes.     

Conformation of 2-aminomethylpyrrolidine and 2-aminomethylpiperidine in ternary platinum(II) complexes: regulation of conformation of the diamine by the coexisting ligand

Square-planar complexes with the formula [Pt(L(2))(L(1))](X)(2) x nH(2)O, where L(1) is S-2-aminomethylpyrrolidine (S-pyrda) or 2-aminomethylpiperidine (pipda) and L(2) is diammine (X=Cl), cyclobutane-1,1-dicarboxylato (cbdca) (X=none), 2,2'-bipyridine (bpy) (X=NO(3)), or 1,10-phenanthroline (phen) (X=Cl), were prepared and the nature of the coordination of L(1) was examined by (1)H-NMR spectroscopy and X-ray crystallography. These 2-aminomethylazacycloalkane derivatives form five-membered chelate rings condensed with an azacycloalkane ring in cis- or trans-configurations. The (1)H-NMR spectrum of complexes with S-pyrda as L(1) were consistent with cis-condensed rings in an S(N) conformation with any of L(2) group. However, (1)H-NMR spectra of the complexes with pipda as L(1) indicated trans-fused successive rings for the diammine and cbdca as L(2), but spectra for bpy and phen as L(2) were consistent with a conformation having cis-fused successive rings. X-Ray crystallography data for the two complexes with pipda as L(1) and cbdca (1) and bpy (2) as L(2) confirms the different coordination behavior in the solid state.     

Monolayers (Langmuir films) behavior of multi-component systems composed of a bile acid with different sterols and with their 1:1 mixtures

Different physicochemical properties of Langmuir films (monolayers) composed of 10 mixed systems of a bile acid, deoxycholic acid (DC) with various plant sterols, such as stigmasterol (Stig), beta-sitosterol (Sito) and campesterol (Camp) and a stanol, cholestanol (Chsta) in addition to an animal sterol, cholesterol (Ch) [these sterols and Chsta are abbreviated as St] and DC with 1:1 St mixtures; (Ch+Chsta), (Ch+Stig), (Stig+Chsta), (Ch+Sito) and (Ch+Camp) on the substrate of 5M aqueous NaCl solution (pH 1.2) at 25 degrees C, were investigated in terms of mean surface area per molecule (A(m)), the partial molecular area (PMA), surface excess Gibbs energy (DeltaG((ex))), interaction parameter (I(p)) as well as activity coefficients (f(1) and f(2)) in 2-D phase of each binary (or ternary) component system and elasticity (Cs(-1)) of formed films; these were analyzed on the basis of the respective surface pressure (pi) versus A(m) isotherms as a function of mole fraction of Sts (X(st)) in the DC/St(s) mixtures at discrete surface pressures. Notable findings are: (i) all the binary component systems did form patched film type monolayers consisting of (a) DC-dominant film solubilizing a trace amount of St molecules and (b) St dominant film dissolving a small amount of DC molecules, (ii) DC in 2-D phase exhibited a transition from LE film to LC film at a constant pressure (pi(C)(1)) accompanied by compression and (iii) DeltaG((ex)) as well as I(p) was found to be greatly dependent on (a) the combinations of DC with different St species and (b) to be markedly varied by a difference in mixing ratio of DC to Sts. Compressibility (or elasticity) analyses and fluorescence microscopy images could support the above findings as well as interpretation.     

Rotational spectroscopy of the isotopic species of silicon monosulfide, SiS

Pure rotational transitions of silicon monosulfide ((28)Si(32)S) and its rare isotopic species have been observed in their ground as well as vibrationally excited states by employing Fourier transform microwave (FTMW) spectroscopy of a supersonic molecular beam at centimetre wavelengths (13-37 GHz) and by using long-path absorption spectroscopy at millimetre and submillimetre wavelengths (127-925 GHz). The latter measurements include 91 transition frequencies for (28)Si(32)S, (28)Si(33)S, (28)Si(34)S, (29)Si(32)S and (30)Si(32)S in upsilon = 0, as well as 5 lines for (28)Si(32)S in upsilon = 1, with rotational quantum numbers J'< or = 52. The centimetre-wave measurements include more than 300 newly recorded lines. Together with previous data they result in almost 600 transitions (J' = 0 and 1) from all twelve possible isotopic species, including (29)Si(36)S and (30)Si(36)S, which have fractional abundances of about 7 x 10(-6) and 4.5 x 10(-6), respectively. Rotational transitions were observed from upsilon = 0 for the least abundant isotopic species to as high as upsilon = 51 for the main species. Owing to the high spectral resolution of the FTMW spectrometer, hyperfine structure from the nuclear electric quadrupole moment of (33)S was resolved for species containing this isotope, as was much smaller nuclear spin-rotation splitting for isotopic species involving (29)Si. By combining the measurements here with previously published microwave and infrared data in one global fit, an improved set of spectroscopic parameters for SiS has been derived which include several terms describing the breakdown of the Born-Oppenheimer approximation. With this parameter set, highly accurate rotational frequencies for this important astronomical molecule can now be predicted well into the terahertz region.     

Measurement of inclusion complex formation between cyclophane and biological relevant amino acids using electrospray ionization, cold-spray ionization and fast atom bombardment mass spectrometry

The investigation of the host-guest complex formations between cyclophane (TGDMAP) (1) as a host and L-acidic amino acids such as L-glutamic acid (Glu) and L-aspartic acid (Asp) as guests was carried out using fast atom bombardment (FAB), electrospray ionization (ESI) and cold-spray ionization (CSI) mass spectrometry (MS). The stability constant (K(s)) values obtained by the three different MS methods almost agreed. However, the complex ion peaks of a novel cyclophane (CPCn) (2) with Glu and Asp were not observed in FAB-MS. Then, these host-guest complex formations by use of CSI-MS and ESI-MS was examined, as the results, these complex ion peaks were observed clearly and the measurement values by the two MS methods are mostly in agreement. It was concluded that ESI-MS and CSI-MS are available for the determination of K(s) value as well as FAB-MS.     

Preparation of ethambutol-copper(II) complex and fabrication of PVC based membrane potentiometric sensor for copper

Copper(II) complex of ethambutol (I) was prepared and used in the fabrication of Cu(2+) selective ISE membrane. The membrane having Cu(II)-ethambutol complex (I) as electroactive material, along with sodium tetraphenylborate (NaTPB) as anion discriminator, dioctylphthalate (DOP) as plasticizer in poly(vinyl chloride) (PVC) matrix in the percentage ratio 6:2:190:200 (I:NaTPB:DOP:PVC) (w/w) gave a linear response in the concentration range 7.94x10(-6) to 1.0x10(-1) M of Cu(2+) with a slope of 29.9+/-0.2 mV per decade of activity and a fast response time of 11+/-2 s. The sensor works well in the pH range 2.1-6.3 and could be satisfactorily used in presence of 40% (v/v) methanol, ethanol and acetone and is selective for copper over a large number of cations with slight interference from Na(+) and Co(2+) if present at a level 1.5x10(-5) and 6.5x10(-5) M, respectively. It works well over a period of 6 months and can also be used as indicator electrode for the end point determination in the potentiometric titration of Cu(2+) against EDTA as well as in the determination of Cu(2+) in real samples.     

Synthesis, characterization and anti proliferative effect of [Au(en)2]Cl3 and [Au(N-propyl-en)2]Cl3 on human cancer cell lines

Two Au(III) complexes of the type [Au(en)2]Cl3 (2a) and [Au(N-pr-en)2]Cl3 (3a) were synthesized by reacting Auric acid (HAuCl(4)·3H2O) with 2 equiv. ethylenediamine (en) or N-alkyl substituted ethylenediamine ligands. This metallodrug was characterized by various analytical and spectroscopic techniques such as elemental analysis, UV-Vis, Far-IR, 1H NMR and solution 13C as well as solid 13C and 15N NMR. Potentiality of [Au(en)2]Cl3 and [Au(N-pr-en)2]Cl3 as an anti-cancer agent were investigated by measuring some relevant physicochemical and biochemical properties such as stability of Au-N bonds by vibrational stretching from Far IR as well as cytotoxicity and stomach cancer cell inhibiting effect, respectively. The solid-state 15N NMR chemical shift shows that the ligand is strongly bound to gold(III) centre via N atoms. The computational study of 2a shows that the gold coordination sphere adopts distorted square planar geometry with bidentate ethylenediamine ligands acting as a tetradentate chelate. While stable in the solution state, the in vitro biological studies performed with these compounds 2a in solution showed higher activity towards the inhibitory effects of the human cancer cell lines such as prostate cancer (PC-3) and gastric carcinoma (SGC-7901) than that of the N-substituted gold(III) complex (3a). Cytotoxicity of the new compounds has also been estimated in PC-3 and SGC-7901 cells.     

51V magic angle spinning NMR spectroscopy of Keggin anions [PVnW12-nO40](3+n)-: effect of countercation and vanadium substitution on fine structure constants

Vanadium environments in Keggin oxopolytungstates were characterized by (51)V solid-state MAS NMR spectroscopy. (C(4)H(9))(4)N(+)-, K(+)-, Cs(+)-, as well as mixed Na(+)/Cs(+)- salts of the mono-, di-, and trivanadium substituted oxotungstates, [VW(11)O(40)](4-), [V(2)W(10)O(40)](5-), and [V(3)W(9)O(40)](6-), have been prepared as microcrystalline and crystalline solids. Solid-state NMR spectra report on the local environment of the vanadium site in these Keggin ions via their anisotropic quadrupolar and chemical-shielding interactions. These (51)V fine structure constants in the solid state are determined by the number of vanadium atoms present in the oxoanion core. Surprisingly, the quadrupolar anisotropy tensors do not depend to any significant extent on the nature of the countercations. On the other hand, the chemical-shielding anisotropy tensors, as well as the isotropic chemical shifts, display large variations as a function of the cationic environment. This information can be used as a probe of the local cationic environment in the vanadium-substituted Keggin solids.     

Water-soluble monodispersed lanthanide oxide submicrospheres: PVP-assisted hydrothermal synthesis, size-control and luminescence properties

We report a facile hydrothermal synthetic route to prepare a class of monodispersed lanthanide-based compound submicrospheres with controllable size, which employs raw lanthanide oxides as starting material, urea as precipitator and poly(N-vinyl-2-pyrrolidone) (PVP) as surfactant. Dependent on the intrinsic properties of respective lanthanide, the resulting products could be in the form of oxide, hydroxide or basic carbonate. These lanthanide hydroxides or basic carbonates can be easily transformed into their corresponding oxides by calcination, retaining the same morphology and size dispersion. The formation mechanism of these lanthanide-based compound submicrospheres is investigated and PVP plays a critical role in forming uniform and well-dispersed products. Furthermore, this method could be extended to a binary system by using two kinds of lanthanide oxides as starting material, resulting in doped-type lanthanide oxide submicrospheres (such as Y(2)O(3):Eu(3+)). The Y(2)O(3):Eu(3+) submicrospheres exhibit nearly uniform spherical morphology and narrow size distribution as well as good water solubility and sharp spectral emission at 610 nm (corresponding to the 5D(0)-7F(2) transition of Eu(3+)). This makes them attractive materials for applications in fields such as fluorescent lamps, field emission displays (FEDs) or LCDs, or as biomedical labels and molecular probes.     

Atom Transfer Radical Polymerization (ATRP) of Ethyl Acrylate: Its Mechanistic Studies

Atom transfer radical polymerization (ATRP) of ethyl acrylate was carried out in bulk using ethyl 2-bromoisobutyrate as initiator, CuBr as well as CuCl as catalyst in combination with different ligands e.g., 2,2′ bipyridine (bpy)andN,N, N′,N″,N″-pentamethyldiethylenetriamine (PMDETA). In most of the cases very high conversion (72–98%) was achieved. The polymerization was well controlled with a linear increase of molecular weight (M_n^SEC) with conversion and relatively narrow molecular weight distributions (polydispersity index 1.2–1.3). Use of PMDETA as the ligand resulted in faster polymerization rate (98% conversion in 1 h) than those using bipyridine (72% conversion in 5 h). The MALDI-TOF-MS analysis of poly (ethyl acrylate) (PEA) prepared by using bpy as ligand showed the presence of halogen as the end group. On the contrary, when PMDETA was used as the ligand, the mass analysis showed no trace of this end group.     

CO(2)-Induced Degradation of Amine-Containing Adsorbents: Reaction Products and Pathways

A comprehensive study was conducted to investigate the stability of a wide variety of mesoporous silica-supported amine-containing adsorbents in the presence of carbon dioxide under dry conditions. CO(2)-induced degradation of grafted primary and secondary monoamines (pMono, sMono), diamines with one primary and one secondary amines (Diamine) and triamine with one primary and two secondary amines (TRI) as well as different impregnated polyamines such as branched and linear polyethylenimine (BPEI and LPEI) and polyallylamine (PALL) was investigated using extensive CO(2) adsorption-desorption cycling as well as diffuse reflectance infrared Fourier transform (DRIFT) and (13)C CP MAS NMR measurements. Except for sMono, all other supported amines underwent significant deactivation in the presence of dry CO(2) under mild conditions. In all cases, the decrease in CO(2) uptake was associated with the formation of urea linkages at the expense of amine groups. The urea-containing species were identified, and the deactivation pathways were delineated.     

Crystal structure and morphology evolution in the LaXO3, X = Al, Ga, In nano-oxide series. Consequences for the synthesis of luminescent phosphors

The LaXO(3):Tb(3+) (X = Al(3+), Ga(3+), In(3+)) perovskite nanoparticles were obtained using the nonhydrolytic treatment (Bradley reaction) of the molecular precursors of the La(O(i)Pr)(3), Al(O(i)Pr)(3), Ga(O(i)Pr)(3), In(5)O(O(i)Pr)(13), and Tb(acac)(3), respectively. It was shown that crystal structure and morphology evolution in the LaXO(3), X = Al, Ga, In nano-oxide series depended on the size and chemical properties of the X-metal atom. Formation of the LaInO(3):Tb(3+) nanoparticles is distinctly less thermodynamically demanding on contrary to the LaAlO(3):Tb(3+) and LaGaO(3):Tb(3+) since it provided crystalline product directly in the solution synthesis at 202 °C, which is the lowest reported synthesis temperature for this compound up-to-date. This behavior was ascribed to the effects directly connected with the dopant substitution (exchange of bigger La(3+) cation with smaller Tb(3+)) as well as reduction of the particle size. The size effects are mostly reflected in the expansion of the cell volume, changes of the cell parameters as well as shifting and broadening of the Raman bands. Indirectly, size reduction has also an effect on the luminescence properties through the higher probability of presence of surface and net defects as well as heterogeneous distribution of the Tb(3+) ions caused by high surface-to-volume ratio. The prepared nanophosphors show basically green emission with exception of white-green in case of the LaInO(3):Tb(3+). Strong emission quenching was found in the latter case being most likely a consequence of the nonradiative energy transfer between Tb(3+) and In(3+) as well as the presence of defects. In comparison to the Pechini's method, the LaXO(3) nanoparticles required significantly lower annealing temperature (700 °C) necessary for complete crystallization. Generally the resulting particles are distinctly smaller (5 to 25 nm) and less agglomerated (50-100 nm) depending on the reaction conditions as well as thermal treatment. For the first time, it was shown that the LaGaO(3):Tb(3+) nanopowder has crystallized in the high-temperature rhombohedral R3c phase.     

Studies on the synthesis of condensed pyridazine derivatives. IV. Synthesis and anxiolytic activity of 2-aryl-5,6-dihydro-(1)benzothiepino[5,4- c]pyridazin-3(2H)-ones and related compound.

A series of 2-aryl-5,6-dihydro-(1)benzothiepino[5,4-c]pyridazin-3(2H)- ones and related compounds were synthesized and evaluated for their ability to displace 3H-diazepam from rat brain membranes in vitro, and to prevent bicuculline induced convulsions in mice in vivo. Compounds with a 4'-methoxyphenyl (36) or 4'-chlorophenyl group (37, 39--42) as 2-aryl substituents showed prominent activities in both the in vitro and in vivo tests. Among them, 2-(4'-chlorophenyl)-5,6-dihydro- (37) and 2-(4'-chlorophenyl)-5,6-dihydro-10-fluoro-(1)benzothiepino[5,4-c]+ ++pyridazin- 3(2H)-one 7-oxides (41) showed activity twice as potent as diazepam in an anticonflict test (Vogel type, rats) while exhibiting less muscle relaxation (rotarod test, mice) and augmentation of gamma-aminobutyric acid-induced chloride current (Icl) in isolated frog sensory neurones than diazepam. Compound 37 (Y-23684) was selected from this series as a candidate for further development. The structure-activity relationships are discussed.     

The use of a polymer inclusion membrane in a paper-based sensor for the selective determination of Cu(II)

A disposable paper-based sensor (PBS) is described for the determination of Cu(II) in natural and waste waters at approximately 2 cents per measurement. The device makes use of a polymer inclusion membrane (PIM) to provide the selectivity for Cu(II). The PIM consists of 40 wt% di(2-ethlyhexyl) phosphoric acid (D2EHPA) as the carrier, 10 wt% dioctyl phthalate (DOP) as a plasticizer, 49.5 wt% poly(vinyl chloride) (PVC) as the base polymer and 0.5 wt% (m m⁻¹) 1-(2′-pyridylazo)-2-naphthol (PAN) as the colourimetric reagent. High selectivity under mildly acidic conditions (HCl, pH 2.0) is achieved for Cu(II) in the presence of frequently encountered metal ions in natural and waste waters such as Fe(III), Al(III), Zn(II), Cd(II), Pb(II), Ca(II), Mg(II), and Ni(II).