Determination of free and ethoxylated alkylphenols in leather with gas chromatography-mass spectrometry

An analytical approach was developed to determine nonylphenol (NP), octylphenol (OP), nonylphenol ethoxylates (NPEO(n)) and octylphenol ethoxylates (OPEO(n)) in leather samples involving the conversion of NPEO(n) and OPEO(n) into the corresponding NP and OP. The four targets were extracted from samples using ultrasonic-assisted acetonitrile extraction. NP and OP in the extracts were directly isolated with hexane and quantitatively determined with 4-n-nonylphenol as internal standard by gas chromatography-mass spectrometry (GC-MS). For NPEO(n) and OPEO(n) in the extracts, they were first converted into NP and OP with aluminum triiodide as cleavage agent, and the yielded NP and OP were determined by GC-MS. The contents of NPEO(n) and OPEO(n) were calculated by normalizing to NPEO(9) and OPEO(9), respectively. This method was properly validated and the real sample tests revealed the pollution significance of leather by NPEO(n) and OPEO(n).     

Simultaneous determination of the endocrine disrupting compounds nonylphenol, nonylphenol ethoxylates, triclosan and bisphenol A in wastewater and sewage sludge by gas chromatography-mass spectrometry

An integrated analytical method for the simultaneous determination of 4-n-nonylphenol (4-n-NP), nonylphenol monoethoxylate (NP1EO), nonylphenol diethoxylate (NP2EO), bisphenol A (BPA) and triclosan (TCS) in wastewater (dissolved and particulate phase) and sewage sludge was developed based on gas chromatography-mass spectrometry. Chromatographic analysis was achieved after derivatization with bis(trimethylsilyl)trifluoroacetamide (BSTFA). Extraction from water samples was performed by solid-phase extraction (SPE). The optimization of SPE procedure included the type of sorbent and the type of the organic solvent used for the elution. Referred to solid samples, the target compounds were extracted by sonication. In this case the optimization of the extraction procedure included the variation of the amount of the extracted biomass, the duration and the temperature of sonication and the type of the extraction organic solvent. The developed extraction procedures resulted in good repeatability and reproducibility with relative standard deviations (RSDs) less than 13% for all the tested compounds for both types of samples. Satisfactory recoveries were obtained (>60%) for all the compounds in both liquid and solid samples, except for 4-n-NP, which gave recoveries up to 35% in wastewater samples and up to 63% in sludge samples. The limits of detection (LODs) of the target compounds varied from 0.03 (4-n-NP) to 0.41 microg l(-1) (NP2EO) and from 0.04 (4-n-NP) to 0.96 microg kg(-1) (NP2EO) for liquid and solid samples, respectively. The developed methods were successfully applied to the analysis of the target compounds in real samples.     

Selective solid-phase extraction of amoxicillin and cephalexin from urine samples using a molecularly imprinted polymer

In this paper we describe, for the first time, a molecularly imprinted polymer (MIP) for the antibiotic amoxicillin (AMX), synthesised by a noncovalent molecular imprinting approach and used to extract AMX selectively from urine samples. The MIP was applied as a molecularly selective sorbent in molecularly imprinted SPE (MISPE) in an off-line mode, where it showed useful cross-selectivity for a structurally related antibiotic, cephalexin (CPX). By using a MISPE protocol, the MIP was able to selectively extract both AMX and CFX from 5 mL of water spiked with 10 mg/L with recoveries of 75 and 78% for AMX and CFX, respectively. When applied to real samples (urine) at clinically relevant concentrations, recoveries from 2 mL of human urine spiked with 20 mg/L decreased slightly to 65 and 63% for AMX and CFX, respectively. To demonstrate further the selectivity of the MIP obtained, a comparison with commercially available SPE cartridges was performed. Improvements in the retention of both AMX and CFX on the MIP were obtained relative to the commercially available cartridges, and the MISPE extracts were considerably cleaner, due to molecularly selective analyte binding by the MIP.     

Removal of endocrine‐disrupting compounds from water using macroporous molecularly imprinted cryogels in a moving‐bed reactor

Highly efficient removal of endocrine‐disrupting compounds (EDCs) such as 17β‐estradiol (E2), 4‐nonylphenol (NP) and atrazine from water was achieved using a novel macroporous adsorption medium. The medium consisted of a macroporous poly(vinyl alcohol) (PVA) cryogel with molecularly imprinted polymer (MIP) particles embedded in it. The MIP was prepared using E2, NP and atrazine as templates. The macroporous composite molecularly imprinted cryogels were formed inside the open‐ended protective shells, known as Kaldnes carriers. These adsorbents (defined as Macroporous Gel Particles, MGPs) were evaluated on the removal of E2, NP and atrazine from water using different column configurations, namely column filled with the MGPs (packed‐bed column) and in moving‐bed reactors (defined here as moving‐bed MGPs reactor). Complete binding (> 99%) of E2 from a spiked aqueous solution (1 mg/L) was achieved using E2‐MIP/MGPs in a moving‐bed MGPs reactor at the retention time in the reactor of 4 min, while only 77% was bound to the nonimprinted medium (NIP/MGPs). Similar results were also obtained for the adsorption medium imprinted with atrazine. All contaminants studied (E2, atrazine and NP) were effectively removed from water at low (environmentally relevant) concentrations by the respective adsorption medium.     

Determination of a flame retardant hydrolysis product in human urine by SPE and LC–MS. Comparison of molecularly imprinted solid-phase extraction with a mixed-mode anion exchanger

Diphenyl phosphate is a hydrolysis product and possible metabolite of the flame retardant and plasticiser additive triphenyl phosphate. A molecularly imprinted polymer solid-phase extraction (MISPE) method for extracting diphenyl phosphate from aqueous solutions has been developed and compared with SPE using a commercially available mixed-mode anion exchanger. The imprinted polymer was prepared using 2-vinylpyridine (2-Vpy) as the functional monomer, ethylene glycol dimethacrylate (EGDMA) as the cross-linker, and a structural analogue of the analyte as the template molecule. The imprinted polymer was evaluated for use as a SPE sorbent, in tests with both aqueous standards and spiked urine samples, by comparing recovery and breakthrough data obtained using the imprinted form of the polymer and a non-imprinted form (NIP). Extraction from aqueous solutions resulted in more than 80% recovery. Adsorption by the molecularly imprinted polymer (MIP) was non-selective , but selectivity was achieved by selective desorption in the wash steps. Diphenyl phosphate could also be selectively extracted from urine samples, although the urine matrix reduced the capacity of the MISPE cartridges. Recoveries from urine extraction were higher than 70%. It was important to control pH during sample loading. The MISPE method was found to yield a less complex LC–ESI–MS chromatogram of the urine extracts compared with the mixed-mode anion-exchanger method. An LC–ESI–MS method using a Hypercarb LC column with a graphitised carbon stationary phase was also evaluated for organophosphate diesters. LC–ESI–MS using negative-ion detection in selected ion monitoring (SIM) mode was shown to be linear for diphenyl phosphate in the range 0.08–20 ng L^–1.     

Selective solid-phase extraction using molecularly imprinted polymer for the analysis of polar organophosphorus pesticides in water and soil samples

An analytical methodology for the analysis of four polar organophophorus pesticides (monocrotophos, mevinphos, phosphamidon, omethoate) in water and soil samples incorporating a molecularly imprinted solid-phase extraction (MISPE) process using a monocrotophos-imprinted polymer was developed. Binding study demonstrated that the polymer showed excellent affinity and high selectivity to monocrotophos. The MISPE procedure including the clean-up step to remove any interferences was optimized. The accuracy and selectivity of the MISPE process developed were verified using a non-imprinted (blank) polymer and a classical ENVI-18 cartridge as the SPE matrix during control experiments. The use of MISPE improved the accuracy and precision of the GC method and lowered the limit of detection. The recoveries of four polar organophosphorus pesticides (OPPs) extracted from 1 L of river water at a 100 ng/L spike level were in the range of 77.5-99.1%. The recoveries of organophosphorus pesticides extracted from a 5-g soil sample at the 100 microg/kg level were in the range of 79.3-93.5%. The limit of detection varied from 10 to 32 ng/L in water and from 12 to 34 microg/kg in soil samples. The molecularly imprinted polymer (MIP) enabled the selective extraction of four organophosphorus pesticides successfully from water and soil samples, demonstrating the potential of molecularly imprinted solid-phase extraction for rapid, selective, and cost-effective sample pretreatment.     

Molecularly imprinted solid-phase extraction of (-)-ephedrine from Chinese Ephedra

Method of molecularly imprinted solid phase extraction (MISPE) of (-)-ephedrine from Chinese Ephedra has been developed in the research. The molecularly imprinted polymer (MIP) with good selectivity and affinity for (-)-ephedrine was synthesized with (-)-ephedrine as the template, methacrylic acid as the functional monomer. The washing and elution conditions in MISPE were selected and optimized for efficient analyte extraction and sample clean-up. A clean analytical HPLC base line of ephedra extract was obtained after MISPE, which indicated that the sample pre-treatment was efficient. Good recovery and precision were obtained in the assessment for the MISPE-HPLC procedure, which demonstrated it is a reliable method and can be used for the determination of (-)-ephedrine in herbal ephedra.     

Molecularly imprinted solid-phase extraction for the selective HPLC determination of ractopamine in pig urine

A method was developed for the determination of ractopamine in pig urine using molecularly imprinted solid-phase extraction (MISPE) as the sample clean-up technique combined with high-performance liquid chromatography. The molecularly imprinted polymer (MIP) was synthesized in acetonitrile-triethylamine system using ractopamine (RAC) as the template and acrylamide as the monomer. The binding capacity of the polymer toward RAC was found to be about 2.57 mg of ractopamine/g of polymer. The optimal procedures for MISPE consisted of conditioning with 3 mL methanol, equilibrating with 3 mL of water, loading volume of <10 mL of aqueous sample (pH 7), washing with 3 mL water and 3 mL methanol, and eluting with 5 mL of 5% ammonia in methanol. In the four spiked samples with the levels of 0.01, 0.1, 1.0 and 5.0 μg/mL, the mean recoveries of analyte on the MIP were higher than 90% with relative standard deviation <10%, and significant differences between imprinted and non-imprinted materials were observed. The MIP selectivity was evaluated by checking 11 drugs with similar and different molecular structures to that of RAC. The characteristics of three-dimensional cavities and hydrogen bond interaction were regarded as the main factors that dominated the retention of RAC on the MISPE cartridge.     

Solid-phase extraction using a molecularly imprinted polymer for the selective purification and preconcentration of norfloxacin from seawater

Abstract

A highly selective and effective method for the purification and preconcentration of norfloxacin (NFX) in seawater samples was developed based on molecularly imprinted solid-phase extraction (MISPE). The molecularly imprinted polymer was synthesized by precipitation polymerization. Methacrylic acid (MAA) and ethylene glycol dimethacrylate (EGDMA) were used as the functional monomer and crosslinker, respectively. The resulting molecularly imprinted polymer (MIP) showed high adsorption for NFX and was selective for its solid-phase extraction. An offline MISPE method followed by high performance liquid chromatography with diode array detection was established for the determination of NFX in seawater. The recoveries of spiked seawater samples using the MISPE columns were satisfactorily higher than 77.6%. The relative standard deviation was less than 5.60%, and the limit of detection was 0.027?μg L^?1. Four seawater samples obtained from the Bohai Sea were analyzed, and NFX was found only at one location at a concentration of 0.280?μg L^?1.     

Size-exclusion chromatography in 1,1,1,3,3,3-hexafluoro-2-propanol

Two molecularly imprinted polymers (MIPs) have been synthesised for the selective extraction of 4-nitrophenol (4-NP) from water samples. One polymer was synthesised via a non-covalent approach and the other via a semi-covalent approach. The selectivity of the polymers for 4-NP was evaluated when these polymers were applied in on-line solid-phase extraction (MISPE) coupled to reversed-phase HPLC. The MISPE conditions for both MIPs were optimised and a clean-up step was included to eliminate non-specific interactions. Differences between the two MIPs were observed with the non-covalent MIP being the more selective of the two, whereas the recoveries were slightly higher for the semi-covalent MIP. The performance of the imprinted polymers in the MISPE of real water samples was also evaluated.     

磁性碳纳米管表面新型壬基酚印迹纳米复合材料制备及吸附性能

采用聚苯胺包覆的磁性多壁碳纳米管为载体,以壬基酚(NP)为模板分子,甲基丙烯酸(MAA)为功能单体,乙二醇二甲基丙烯酸酯(EGDMA)为交联剂制备新型磁性壬基酚印迹复合萃取材料。 采用扫描电子显微镜(SEM)、红外光谱(FT-IR)和样品振动磁强计(VSM)等技术手段对该磁性印迹复合材料进行表征和分析,结果表明,在磁性碳纳米管表面成功接枝厚度为60~70 nm的印迹聚合层。 采用高效液相色谱(HPLC)技术对该印迹复合材料的吸附性能进行探讨,结果表明,该磁性印迹复合材料对壬基酚具有特异性吸附性能,最大吸附量为38.46 mg/g。 结合HPLC检测技术,该磁性印迹复合材料成功用于分离富集饮用水中的壬基酚。     

Molecularly imprinted polymer-based solid-phase extraction combined with molecularly imprinted polymer-based sensor for detection of uric acid

The development of an easy-to-use, rapid, robust and inexpensive technique is required which can measure the basal concentration of uric acid (UA) lower than 1.0 x 10(-7)M ( approximately 0.017 mgL(-1)) in biological samples to attend the problem of hypouricemia. In the present work an artificial receptor for UA, silica gel-bonded molecularly imprinted polymer (MIP), was used as a sorbent for molecularly imprinted solid-phase extraction (MISPE) in column chromatography. The use of a sensor based on a MIP-modified hanging mercury drop electrode (HMDE), as reported from our laboratory, could estimate UA with detection limit as low as 0.024 mgL(-1) under the optimized conditions of differential pulse, cathodic stripping voltammetric (DPCSV) measurement. However, in the current investigation, with the use of the combination of MISPE followed by detection with a MIP-based HMDE sensor, the minimum detectable concentration could go down to 0.0008 mgL(-1) (RSD=0.63%, S/N=3). The same MIP receptor for both MISPE and the corresponding sensor was able to enhance the preconcentration of analyte substantially so as to attain the desired level of sensitivity; and that to without any interference (cross-reactivity) from other structurally related analogues including the major interferent like ascorbic acid prevalent in the aqueous environment of biological samples.     

Selective molecularly imprinted polymer obtained from a combinatorial library for the extraction of bisphenol A

In the present work, an analytical methodology based on molecularly imprinted solid-phase extraction (MISPE) has been developed for the determination of bisphenol A (BPA) in environmental and food samples. In order to select the optimum material, a combinatorial library of molecularly imprinted polymers in small-scale (mini-MIPs) was prepared using BPA as template. Different monomers (methacrylic acid or 4-vinylpyridine), crosslinkers (ethylene glycol dimethacrylate or trimethylolpropane trimethacrylate) and porogens (methanol, acetonitrile or toluene) were used leading to 24 different polymerisation mixtures. After BPA removal, the ability of mini-MIPs to recognise BPA was evaluated by equilibrium rebinding-elution experiments. The copolymer of 4-vinylpyridine (4-VP) and trimethylolpropane trimethacrylate (TRIM) prepared in toluene showed the higher affinity for the template. Subsequently, a scaled-up version of the optimum polymer was prepared and used in the development of MISPE procedures for the extraction of BPA. The optimised MISPE protocols were successfully applied to the selective extraction of BPA from soils and aqueous canned peas samples.     

Development of a Sensitive Method for the Determination of 4‐(Methylnitrosamino)‐1‐(3‐pyridyl)‐1‐butanol in Human Urine Using Solid‐phase Extraction Combined with Ultrasound‐assisted Dispersive Liquid–liquid Microextraction and LC‐MS/MS Detection

An efficient and sensitive analytical method based on molecularly imprinted solid‐phase extraction (MISPE) and reverse‐phase ultrasound‐assisted dispersive liquid–liquid microextraction (USA‐DLLME) coupled with LC–MS/MS detection was developed and validated for the analysis of urinary 4‐(methylnitrosamino)‐1‐(3‐pyridyl)‐1‐butanol (NNAL), a tobacco‐specific nitrosamine metabolite. The extraction performances of NNAL on three different solid‐phase extraction (SPE) sorbents including the hydrophilic‐lipophilic balanced sorbent HLB, the mixed mode cationic MCX sorbent and the molecularly imprinted polymers (MIP) sorbent were evaluated. Experimental results showed that the analyte was well retained with the highest extraction recovery and the optimum purification effect on MIP. Under the optimized conditions of MIP and USA‐DLLME, an enrichment factor of 23 was obtained. Good linearity relationship was obtained in the range of 5‐1200 pg/mL with a correlation coefficient of 0.9953. The limit of detection (LOD) was 0.35 pg/mL. The recoveries at three spiked levels ranged between 88.5% and 93.7%. Intra‐ and inter‐day relative standard deviations varied from 3.6% to 7.4% and from 5.4% to 9.7%, respectively. The developed method combing the advantages of MISPE and DLLME significantly improves the purification and enrichment of the analyte and can be used as an effective approach for the determination of ultra‐trace NNAL in complex biological matrices.     

吲哚美辛纳米胶体金分子印迹聚合物的制备及其在固相萃取中的应用

以吲哚美辛(IDM)为模板分子,丙烯酰胺(AA)为功能单体,乙二醇二甲基丙烯酸酯(EGDMA)为交联剂,本体聚合法制备过程中加入纳米胶体金,合成了吲哚美辛胶体金分子印迹聚合物(MIPs/Au),利用MIPs/Au表面胶体金对蛋白吸附作用,将抗吲哚美辛的多克隆抗体固定在MIPs/Au上,得到表面固定有抗体的新型聚合物(MIPs/Au-Ab)并对其进行了表征。制备了填充材料为MIPs/Au-Ab的固相萃取柱并对其上样、淋洗和洗脱条件进行了优化,并将所制备的新型萃取柱用于水样中IDM的分离富集。抗吲哚美辛抗体交联在聚合物表面,不仅增加了萃取柱的特异性吸附容量,而且有效地降低了MIP的非特异性吸附。     

On‐line determination of 4‐nitrophenol by combining molecularly imprinted solid‐phase extraction and fiber‐optic spectrophotometry

In the present paper, we describe a new on‐line SPE system where molecular imprinting, fiber‐optic detection and flow injection analysis were combined for the first time. This new system has been applied for the on line detection of 4‐nitrophenol (4‐NP). Initially, molecularly imprinted polymers (MIP) have been prepared for the selective extraction of 4‐NP using 4‐vinylpyridine and ethylene glycol dimethacrylate as functional and cross‐linking monomers, respectively. Selective extraction was achieved using the designed MIP with 97% of recovery on imprinted polymer and 10% on control polymer. The system provided a high degree of accuracy, with RSDs varying between 0.7 and 1.39%. In respect of accuracy, reproducibility, and rapidity, this system is comparable with HPLC. In short, the system allows simple, fast, and accurate analyte determination with the possibility of future automation.     

Preliminary evaluation of new polymer matrix for solid-phase extraction of nonylphenol from water samples

Molecularly imprinted (MIP) and blank polymers with affinity for nonylphenol were designed using computational modelling. Chromatographic tests demonstrated higher affinity of imprinted polymers towards the template nonylphenol as compared with blank polymers. The performance of both polymers in solid-phase extraction was however very similar. Both blank and imprinted polymers appeared to be suitable for the removal and pre-concentration of nonylphenol from contaminated water samples with 99% efficiency of the recovery. The commercial resins PH(EC) (Biotage) and C18 (Varian) tested in the same conditions used for comparative purposes had recovery rate <84%. The polymer capacity for nonylphenol was 231 mg g⁻¹ for blank and 228 mg g⁻¹ for MIP. The synthesised materials can have significance for sample pre-concentration and environmental analysis of this class of compounds.     

Solid-phase extraction of fluoroquinolones from aqueous samples using a water-compatible stochiometrically imprinted polymer

A novel and simple method for the selective cleanup and preconcentration of fluoroquinolone antibiotics in environmental water samples has been developed using molecularly imprinted polymer solid-phase extraction (MISPE). The molecularly imprinted polymer (MIP) has been prepared using enrofloxacin (ENR) as the template and a stoichiometric quantity of urea-based functional monomer to target the single oxyanionic moieties in the template molecule. The selectivity of the material for enrofloxacin, and structurally related and non-related compounds, has been evaluated using it as stationary phase in liquid chromatography. The novel polymer and the corresponding non-imprinted material (NIP) have been characterised using nitrogen adsorption-desorption isotherms and scanning electron microscopy. Various parameters affecting the extraction efficiency of the materials in the MISPE procedure were evaluated in order to achieve optimal preconcentration and to reduce non-specific interactions. The optimized MISPE/HPLC with fluorescence detection (FLD) method allows direct extraction of the antibiotics from the aqueous samples followed by a selective washing with acetonitrile/water (0.1M 2-[4-(2-hydroxyethyl)-1-piperazinyl]ethanesulfonic acid (HEPES) buffer, pH 7.5) (10/90, v/v) and elution with 2% trifluoracetic acid in methanol. Good recoveries and precision, ranging between 66 and 100% (RSD: 2-12%, n=3) for danofloxacin, enrofloxacin, oxolinic acid and flumequine, and moderate recoveries (15-40%, RSD 4-9%, n=3) for norfloxacin, ciprofloxacin, lomefloxacin and sarafloxacin, have been obtained for river water samples fortified with 0.50, 0.75 and 1.0microgL(-1) of all the antibiotics. The method detection limits ranged between 0.01 and 0.30microgL(-1) for all the antibiotics tested, when 100mL water samples were processed. The results demonstrate the applicability of the optimized method for the selective extraction of fluoroquinolones in environmental water samples at the ngL(-1) level.     

Synthesis and application of molecularly imprinted polymer on selective solid-phase extraction for the determination of monosulfuron residue in soil

A novel sample clean-up procedure using molecularly imprinted polymer as the solid-phase extraction material for the determination of monosulfuron residue in soil samples has been developed. The molecularly imprinted polymer (MIP) was synthesized by non-covalent method with monosulfuron as the template. The selectivity and affinity of the MIP was evaluated by equilibrium adsorption and HPLC experiments, which demonstrated that the MIP has specific affinity for the template. The template-MIP interaction was studied by investigating the influence of different mobile phases on the retention of the template, which provided basic knowledge for the selection of the washing and elution solutions in the molecularly imprinted solid-phase extraction (MISPE) process. The study indicated that polar organic solvents with hydrogen bonding abilities have stronger eluting strength for the monosulfuron. After the MISPE procedure, a clean baseline was obtained in the HPLC quantification analysis. The recoveries of the method using the combination of MISPE and HPLC were above 93% and the R.S.D. was less than 3.2% in the soil sample determinations. Low detection limit (0.08 microg g(-1), when defined as 3 times of the noise) was also obtained in the method evaluation study.     

Molecularly imprinted on-line solid-phase extraction combined with flow-injection chemiluminescence for the determination of tetracycline

A molecularly imprinted polymer solid phase extraction (MISPE) method combined with flow-injection chemiluminescence (FI-CL) for the determination of residual tetracycline (TC) in fish samples is presented. The molecularly imprinted polymer (MIP) of TC was synthesized and particles of this MIP were packed into a polytetrafluoroethylene (PTFE) tube, which was connected into the sampling loop of an eight-way injection valve and served as the MISPE column for on-line selective adsorption of TC. The eluent (CH3CN : HNO3 (0.01 mol L(-1)) = 4 ratio 1, v ratio v) was used for extracting the adsorbed TC, which could be detected by its good enhancing effect on the CL reaction between Ce(iv) and rhodamine B. The CL intensity is linear to TC concentration in the range from 4 x 10(-9) to 4 x 10(-7) g mL(-1). The detection limit is 1 x 10(-9) g mL(-1) (3 sigma) and the relative standard deviation is 2.4% (n = 9). The conditions of preconcentration, extraction and CL reaction were carefully studied. The selectivity experiment shows that the selectivity and sensitivity of the CL method could be improved greatly when MIP was used as a recognition material in SPE. However, the MISPE column interacted indiscriminately with oxytetracycline (OTC) with a 49 +/- 2% binding. An intermediate differential pulsed elution (DPE) step using 3% acetic acid as eluent was employed to remove OTC and other interfering substances. The proposed MISPE-CL method has been applied successfully to the determination of TC in fish samples. At the same time, the binding characteristics of the polymer to tetracycline were evaluated by batch and dynamic methods.