Simultaneous determination of t,t-muconic, S-phenylmercapturic and S-benzylmercapturic acids in urine by a rapid and sensitive liquid chromatography/electrospray tandem mass spectrometry method

We describe a rapid and sensitive high-performance liquid chromatography/electrospray tandem mass spectrometry (HPLC/ESI-MS/MS) method for simultaneous determination of the most relevant metabolites of benzene and toluene, t,t-muconic acid (t,t-MA), S-phenylmercapturic acid (S-PMA), and S-benzylmercapturic acid (S-BMA). Urine samples were purified before analysis by solid-phase microextraction (SPE) on SAX cartridges with 50 mg sorbent mass. The developed method fulfils all the standard requirements of precision and accuracy. Calibration curves were linear within the concentration range of the standards (0-80 microg/L(urine) for t,t-MA, and 0-25 microg/L(urine) for S-PMA and S-BMA), and had correlation coefficients > or =0.997. Limits of detection were 6.0 microg/L for t,t-MA, 0.3 microg/L for S-PMA, and 0.4 microg/L for S-BMA. The method was used to determine t,t-MA, S-PMA and S-BMA levels in urine of 31 gasoline-station workers, with personal monitoring data obtained from radial symmetry passive diffusive samplers. In the context of mean work-shift exposures of 75.9 microg/m(3) (range 9.4-220.2) for benzene and 331.9 microg/m(3) (78.2-932.1) for toluene, metabolite concentrations in end-of-shift urine samples ranged from 23.5-275.3 microg/g(creatinine) for t,t-MA, non-detectable to 0.9 microg/g(creatinine) for S-PMA, and 3.8-74.8 microg/g(creatinine) for S-BMA. No significant correlation was found between the environmental concentrations and urinary metabolites (p > 0.05 for all cases); the ratios of benzene metabolites could be influenced by exposure levels and co-exposure to xylenes and toluene. The high throughput of this procedure should facilitate exploration of the metabolic effects of benzene-related co-exposure to toluene and alkylbenzenes in large populations of subjects exposed to gasoline.     

Hollow fiber membrane-protected solid-phase microextraction of triazine herbicides in bovine milk and sewage sludge samples

A porous polypropylene hollow fiber membrane (HFM)-protected solid-phase microextraction (HFM-SPME) procedure in conjunction with gas chromatography/mass spectrometric analysis for use in the determination of triazine herbicides in bovine milk samples is described. A 65-microm polydimethylsiloxane-divinylbenzne (PDMS-DVB) SPME fiber was protected by an HFM. HFM-SPME experimental parameters such as fiber type, extraction time, extraction temperature and salt concentration were investigated and optimized. The relative standard deviations for the reproducibility of the optimized HFM-SPME method varied from 4.30 to 12.37%. The correlation coefficients of the calibration curves were between 0.9799 and 0.9965 across a concentration range of 0-200 microg l(-1). The method detection limits for triazines in bovine milk were in the range of 0.003-0.013 microg l(-1) and limits of quantification were in the range of 0.006-0.021 microg l(-1). The suitability of HFM-SPME was extended to the analysis of the herbicides in sewage sludge samples. The results demonstrate that HFM-SPME was an efficient pretreatment and enrichment procedure for complex matrices.     

Direct determination of alkyl phosphates in human urine by liquid chromatography/electrospray tandem mass spectrometry

A novel and rapid procedure based on liquid chromatography/tandem mass spectrometry (LC/MS/MS) for the determination of dialkyl phosphates (metabolites of organophosphorus pesticides) in human urine has been developed. After addition of 40 mM tetrabutylammonium acetate, 10 microL of urine sample were directly injected into the LC/MS/MS system. The method was validated yielding calibration curves with correlation coefficients greater than 0.997 and repeatability coefficient of variation (CV) lower than 9%. The accuracy and precision were evaluated by direct injection of spiked samples at 10 and 100 microg/L obtaining recoveries between 78 and 119% with coefficients of variation below 12%. Limits of detection of 1 microg/L for diethyl phosphate (DEP), diethylthiophosphate (DETP) and diethyldithiophosphate (DEDTP) and 2 microg/L for dimethyldithiophosphate (DMDTP) were achieved, all the analytes being detected in negative ion mode. The fragmentation pathway of dialkyl phosphates allowed us the use of an additional transition for confirmation in order to improve their identification in real-world samples. The applicability of the LC/MS/MS method was demonstrated by applying it to the analysis of urine samples of farmers exposed to the organophosphorus pesticide chlorpyrifos. Good correlation between application of the product in the field (citrus orchards), concentration levels of dialkyl phosphates and levels of the chlorpyrifos-specific metabolite (1,3,5-trichloro-2-pyridinol) was obtained.     

Rapid and sensitive determination of phosphorus-containing amino acid herbicides in soil samples by capillary zone electrophoresis with diode laser-induced fluorescence detection

A straightforward and sensitive method has been developed for the analysis of phosphorus-containing amino acid herbicides (glufosinate and aminomethylphosphonic acid, the major metabolite of glyphosate) in soil samples. For this purpose, the analytical features of two indocyanine fluorescent dyes, sulfoindocyanine succinimidyl ester (Cy5) and 1-ethyl-1-[5-(N-succinimidyl-oxycarbonyl)pentyl]-3,3,3,3-tetramethyl-indodicarbocyanine chloride, as labeling reagents for the determination of these herbicides by CZE with diode LIF detection were investigated. Practical aspects related to the labeling chemistry and CZE separation showed that the two probes behave similarly, Cy5 being the best choice for the determination of these herbicides on account of its higher sensitivity. The optimum procedure includes a derivatization step of the pesticides at 25 degrees C for 30 min and direct injection to CZE analysis, which is conducted within about 14 min using ACN in the running buffer. The lowest detectable analyte concentration ranged from 0.025 to 0.18 microg/L with a precision of 3.6-5.4%. These results indicate that indocyanine fluorescence dyes are useful as rapid and sensitive labels for the determination of these herbicides when compared with typical fluorescein dyes such as FITC and 5-(4,6-dichloro-s-triazin-2-ylamino) fluorescein, because they provide faster labeling reactions even at room temperature and the excess of reagent practically does not interfere the determination. Finally, the Cy5 method was successfully applied to soil samples without a preliminary clean-up procedure, and the herbicides were measured without any interference from coexisting substances. The recoveries of these compounds in these samples at fortification levels of 100-500 ng/g were 90-93%.     

Pesticides and degradation products in groundwaters from a vineyard region: Optimization of a multiresidue method based on SPE and GC‐MS

A reliable multiresidue method based on solid phase extraction was developed using GC–MS to determine and quantify 34 pesticides, including herbicides, fungicides, insecticides, and some of their degradation products, in groundwater in a vineyard region of La Rioja (northern Spain). Different parameters were optimized and good recoveries (65–108% range) and precisions (12–19% range) were achieved with spiked water samples for a concentration of 0.1 μg/L. The experimental results showed an excellent linearity (r² > 0.99) over the 0.1–1.5 μg/L range. The detection limits of the proposed method were 1–37 ng/L for most of the compounds studied. The methodology has been successfully applied to the analysis of groundwater samples from vineyard areas in La Rioja and the presence of pesticides, especially fungicides and herbicides, at several concentration levels was revealed. Terbuthylazine, its metabolite desethyl‐terbuthylazine, and fluometuron were the pesticides most frequently detected in higher concentrations. Overall and taking into consideration the European Union maximum residue limit of pesticides in groundwater, 16 of the 34 compounds included in this study were detected in concentrations over that limit in at least one of the samples analyzed.     

Validated procedure for simultaneous trace level determination of the anti-cancer agent gemcitabine and its metabolite in human urine by high-performance liquid chromatography with tandem mass spectrometry

A sensitive, accurate and reproducible procedure has been developed for the quantitative determination of gemcitabine (2',2'-difluorodeoxycytidine, dFdC) and its metabolite 2',2'-difluorodeoxyuridine (2dFdU) in human urine. The samples (2 mL) were extracted by solid-phase extraction (SPE) and analyzed by reversed-phase high-performance liquid chromatography coupled with tandem mass spectrometry (HPLC/MS/MS), operating in multiple reaction monitoring (MRM mode). This procedure was validated using 2'-deoxycytidine as internal standard (IS). The urine assay was linear over the range 0-50 microg/L, with a limit of quantification (LLOQ) of 0.2 microg/L for gemcitabine and 1.0 microg/L for the metabolite. The respective limits of detection (LODs) for dFdC and 2dFdU were 0.05 and 0.3 microg/L. The precision and accuracy of the assay were determined on three different days. The within-series precision was found to be always less than 8.5 and 12.7% for gemcitabine and 2dFdU, respectively. The overall precision expressed as relative standard deviation (CVr) was always less than 7.1% for both analytes. The recovery of gemcitabine was always greater than 90% with a CVr <6.3%. The measurement uncertainty determined from the validation data assessed the possibility of determining this drug and its metabolite at trace levels in urine, considering that the combined uncertainty of the whole procedure was always less than 30%.     

Analysis of phosphorus herbicides by ion-pairing reversed-phase liquid chromatography coupled to inductively coupled plasma mass spectrometry with octapole reaction cell

A reversed phase ion-pairing high performance liquid chromatographic (RPIP-HPLC) method is developed for the separation of two phosphorus herbicides, Glufosinate and Glyphosate as well as Aminomethylphosphonic acid (AMPA), the major metabolite of Glyphosate. Tetrabutylammonium hydroxide is used as the ion-pairing reagent in conjunction with an ammonium acetate/acetic acid buffering system at pH 4.7. An inductively coupled plasma mass spectrometer (ICP-MS) is coupled to the chromatographic system to detect the herbicides at m/z = 31P. Historically, phosphorus has been recognized as one of the elements difficult to analyze in argon plasma. This is due to its relatively high ionization potential (10.5 eV) as well as the inherent presence of the polyatomic interferences 14N16O1H+ and 15N16O+ overlapping its only isotope at m/z = 31. An octapole reaction cell is utilized to minimize the isobaric polyatomic interferences and to obtain the highest signal-to-background ratio. Detection limits were found to be in the low ppt range (25-32 ng/l). The developed method is successfully applied to the analysis of water samples collected from the Ohio River and spiked with a standard compounds at a level of 20 microg/l.     

Comparison of various liquid chromatographic methods involving UV and atmospheric pressure chemical ionization mass spectrometric detection for the efficient trace analysis of phenylurea herbicides in various types of water samples

The performance of mass spectrometric (MS) detection and UV detection in combination with reversed-phase liquid chromatography without and with the use of coupled column RPLC (LC-LC) has been compared for the trace analysis of phenylurea herbicides in environmental waters. The selected samples of this comparative study originated from an inter-laboratory study. For both detection modes, a 50 mm x 4.6 mm I.D. column and a 100 mm x 4.6 mm I.D. column packed with 3 microm C18 were used as the first (C-1) and second (C-2) column, respectively. Atmospheric pressure chemical ionization mass spectrometry was performed on a magnetic sector instrument. The LC-LC-MS analysis was carried out on-line by means of direct large volume (11.7 ml) injection (LVI). The performance of both on-line (LVI, 4 ml of sample) and off-line LC-LC-UV (244 nm) analysis was investigated. The latter procedure consisted of a solid-phase extraction (SPE) of 250 ml of water sample on a 500 mg C18 cartridge. The comparative study showed that LC-LC-MS is more selective then LC-LC-UV and, in most cases, more sensitive. The LVI-LC-LC-MS approach combines direct quantification and confirmation of most of the analytes down to a level of 0.01 microg/l in water samples in less then 30 min. As regards LC-LC-UV, the off-line method appeared to be a more viable approach in comparison with the on-line procedure. This method allows the screening of phenylurea's in various types of water samples down to a level of at least 0.05 microg/l. On-line analysis with LVI provided marginal sensitivity (limits of detection of about 0.1 microg/l) and selectivity was sometimes less in case of surface water samples. Both the on-line LVI-LC-LC-MS method and the LC-LC-UV method using off-line SPE were validated by analysing a series of real-life reference samples. These samples were part of an inter-laboratory test and contained residues of herbicides ranging from 0.02 to 0.8 microg/l. Beside good correlation between the methods the data agreed very well with the true values of the samples.     

Identification and quantification of the plasma volume expander dextran in human urine by liquid chromatography-tandem mass spectrometry of enzymatically derived isomaltose

Plasma volume expanders are used in sports in order to control haematological parameters and/or to mask erythropoietin (EPO) misuse. A reliable method based on liquid chromatography-tandem mass spectrometry (LC-MS/MS) was developed for doping control purposes, enabling the identification and quantification of the plasma volume expander dextran in human urine. The dextran polymer was enzymatically hydrolysed by alpha-1,6-glucosidase (dextranase) followed by acetylation of the generated isomaltose subunits, allowing the chromatographic separation of different disaccharides, such as lactose, saccharose and isomaltose, as well as the identification and quantification of the analyte in human urine. The method was used to determine the basal concentration of isomaltose resulting from the enzymatic hydrolysis of polymeric 1,6-linked glucose in 238 routine doping control samples. In addition the concentration of dextran measured as isomaltose was estimated in seven urine specimens obtained from patients treated with dextran. Calibration curves for dextran were linear and reproducible. The inter- and intra-assay coefficients of variation for dextran ranged from 4.9 to 7.3% at three concentration levels between 53 and 1186 microg/mL. Recovery ranged from 97 to 112% (mean 106.9%). The assay limit of detection was 3.8 microg/mL and the lower limit of quantification was 12.5 microg/mL. In 96% of the investigated doping control samples, the concentrations of isomaltose were below the LLOQ of 12.5 microg/mL. Even the highest concentrations were approximately 100-300-fold lower than concentrations found in urine samples of patients after intravenous application of dextran. The presented results demonstrate the capability and reliability of the developed LC-MS/MS method for the identification and quantification of dextran in human urine and can be regarded as a method revealing the misuse of dextran in sports.     

Determination of furosemide in urine samples by direct injection in a micellar liquid chromatographic system

A sensitive, selective and efficient micellar liquid chromatographic (MLC) procedure was developed for the determination of furosemide (4-chloro-N-furfuryl-5-sulfamoylanthranilic acid) in urine samples by direct injection and UV detection. The procedure makes use of a C18 reversed-phase column and a micellar mobile phase of 0.05 mol l(-1) sodium dodecyl sulfate-6% v/v propanol and phosphate buffer at pH 3 to resolve furosemide from its photochemical degradation products. The importance of protecting the standards and urine samples to be analysed from light in the assay of furosemide, avoiding its degradation, was verified. The limit of quantification was 0.15 microg ml(-1) and the relative standard deviation of the inter-day assay was 0.8-0.04% in the 6-82 microg ml(-1) range. Detection of urinary excretion of furosemide was followed up to 12 h after ingestion of the drug by a healthy volunteer. No potential interference from the major metabolite (furosemide acylglucuronide) and its hydrolytic product (4-chloro-5-sulfamoylanthranilic acid) was observed. Commonly administered drugs also did not interfere. The proposed MLC procedure permits the rapid and reproducible measurement of low levels of furosemide in a small amount of urine.     

Evaluation of surface- and ground-water pollution due to herbicides in agricultural areas of Zamora and Salamanca (Spain)

The pollution of agricultural land due to herbicides was assessed in the Guare?a and Almar river basins, situated in the provinces of Zamora and Salamanca (Spain). A set of fifteen herbicides, including triazines, ureas, amides and others, was selected owing to their frequency of use, the amounts used, their toxicity and their persistence in the environment. Solid-phase extraction with polymeric cartridges, followed by HPLC with diode-array detection, were used to monitor the herbicides. This technique was chosen owing to the wide range of functionality and polarity of the analytes under study. The detection limits obtained were in the 0.004-0.025 microg/l range (lambda=220 nm). Surface and ground waters, taken from different locations in the basins, were analyzed over a 6-month period. The presence of six out of the fifteen herbicides monitored--chlortoluron, atrazine, terbutryn, alachlor, diflufenican and fluazifop-butyl--was detected in several samples at levels ranging from the detection limit to 1.2 microg/l. The relationship of these herbicides to the agricultural activities of the zone is discussed.     

Compliance analysis of phenylurea and related compounds in drinking water by liquid chromatography/electrospray ionization/mass spectrometry coupled with solid-phase extraction

A liquid chromatography/electrospray ionization/mass spectrometry method was reported for the compliance analysis of seven phenylurea compounds and two related herbicides (tebuthiuron and propanil) in drinking water. The volumes of the sample and final extract used in the method were 500 mL and 10 mL, respectively. The obtained method detection limits were less than 0.03 microg/L, and the mean recoveries were 74-128% with a relative standard deviation of 2.6-8.3% for all the studied compounds. The peak-to-peak signal-to-noise ratios ranged from 3.3 for cis-siduron to 34.2 for fluometuron. The accuracy and precision resulting from reagent and drinking water samples fortified at higher concentration levels were similar to these results. Several analytes were detected in the drinking water samples, including tebuthiuron at 0.5 microg/L, propanil at 0.7 microg/L, diuron at 0.1-2.1 microg/L, and linuron at 0.1-0.8 microg/L.     

Optimization of the headspace solid-phase microextraction for determination of glycol ethers by orthogonal array designs

A headspace solid-phase microextraction (HS-SPME), in conjunction with gas chromatography-flame ionization detection for use in the determination of six frequently used glycol ethers at the microg/l level is described. A 75 microm Carboxenpolydimethylsiloxane fiber was used to extract the analytes from an aqueous solution. Experimental HS-SPME parameters such as extraction temperature, extraction time, salt concentration and sample volume, were investigated and optimized by orthogonal array experimental designs. The relative standard deviations for the reproducibility of the optimized HS-SPME method varied from 1.48 to 7.59%. The correlation coefficients of the calibration curves exceeded 0.998 in the microg/l range of concentration with at least two orders of magnitude. The method detection limits for glycol ethers in deionized water were in the range of 0.26 to 3.42 microg/l. The optimized method was also applied to the analysis of glycol ethers in urine and blood samples with the method detection limits ranged from 1.74 to 23.2 microg/l.     

054 Determination of clarithromycin and its R-14-hydroxy-metabolite in human serum and urine by reversed-phase HPLC and electrochemical detection

Summary Clarithromycin and its main metabolite R-OH-clarithromycin are determined in human serum and urine. The method is based on liquid-liquid extraction, reversed-phase chromatography and dual-mode coulometric detection. The method is fairly selective. No interferences were observed in samples from human volunteers. Detection limits were 0.05 mg/l serum and 1.3 mg/l urine.     

Head-space flow injection for the on-line determination of iodide in urine samples with chemiluminescence detection

A simple head-space (HS) flow injection (FI) system with chemiluminescence (CL) detection for the determination of iodide as iodine in urine is presented. The iodide is converted to iodine by potassium dichromate under stirring in the closed HS vial, and the iodine is released from urine by thermostatting and is carried in a nitrogen flow through an iodide trapping solution. The concomitant introduction of aliquots of iodine, luminol and cobalt(II) solutions by means of a time-based injector into an FI system allowed its mixing in a flow-through cell in front of the detector. The emission intensity at 425 nm was recorded as a function of time. The salting-out of the standard solutions affected the gas-liquid distribution coefficient of iodine in the HS vial. The typical analytical working graphs obtained under the optimized experimental conditions were rectilinear from 0 to 5 mg l(-1) iodine, achieving a precision of 2.3 and a relative standard deviation of 1.8 for ten replicate analyses of 50 and 200 microg l(-1) iodine. However, a second-order process becomes significant at higher iodine concentrations (from 10 to 40 mg l(-1)). The detection limit of the method is 10 microg l(-1) (80 ng) iodine when 8 ml samples are taken. Data for the iodide content of 10 urine samples were in good agreement with those obtained by a conventional catalytic method, and recoveries varied between 101 and 103% for urine samples spiked with different amounts of iodide. The analysis of one sample takes less than 20 min. In the present study the iodide levels found for 100 subjects were 86.8 +/- 19.0 (61-125) microg l(-1), which is lower than the WHO's optimal level (150-300 microg per day).     

Determination of thiazolidine-4-carboxylates in urine by chloroformate derivatization and gas chromatography-electron impact mass spectrometry

The derivatization method of thiazolidine-4-carboxylic acid (TZCA) and methyl-thiazolidine-4-carboxylic acid (Me-TZCA) in urine with alcohol/chloroformate was achieved. TZCA and Me-TZCA were derivatized in one step in urine with ethyl chloroformate in 1 min at room temperature. The derivatives of TZCA and Me-TZCA had very good chromatographic properties and offered very sensitive response for gas chromatography-electron impact ionization-mass spectrometry (GC-EI-MS). On the basis of derivatization, the method for simultaneous determination of TZCA and Me-TZCA in human urine was developed. Deuterated Me-TZCA (Me-TZCA-d(4)) was synthesized as the internal standard (IS) for the analysis of urine samples. TZCA and Me-TZCA were derivatized and extracted from urine at pH 9.5 with toluene, and then the dried extract was dissolved with 100 microl ethyl acetate and injected in GC/MS system. The recoveries of TZCA and Me-TZCA were about 102 and 103%, respectively, at the concentration of 0.05 mg/l. The method detection limits (MDL) were 1.0 and 0.5 microg/l, respectively, for TZCA and Me-TZCA in 1 ml human urine. The coefficients of variation of TZCA and Me-TZCA were less than 6% at the concentrations of 0.05 and 0.2 mg/l, respectively. To assess the formation of TZCA during inhalation with formaldehyde (FA) (about 3.1 and 38.1 ppm FA in air), urine samples from rats were taken during 3 days after initiation of treatment. The mean amount of TZCA determined was 0.07 mg/l in control group and 0.18 mg/l during treatment with 3.1 ppm. The TZCA levels increased up to about 1.01 mg/l during treatment with 38.1 ppm. It is planned to study whether urinary TZCA can be used as an indicator in the biological monitoring of exposure to FA.     

Determination of 8-hydroxy-2'-deoxyguanosine in untreated urine by capillary electrophoresis with UV detection

A capillary electrophoresis method with UV detection was developed for the determination of 8-hydroxy-2'-deoxyguanosine (8-OHdG) in untreated urine samples. The calibration graph for 8-OHdG in urine is linear in the concentration range 10-500 mg/l. and the detection limit is 5 mg/l (17 microM). 8-OHdG was determined in urine from oncological patients treated by radiation therapy. Its concentrations relative to creatinine were found to be in the range 10-47 microg 8-OHdG/l mg creatinine (4-19 micromol 8-OHdG/mmol creatinine). The overall time of the analysis of a urine sample was less than 15 min.     

Comparison of a non-aqueous capillary electrophoresis method with high performance liquid chromatography for the determination of herbicides and metabolites in water samples

A method of capillary electrophoresis (CE) for the determination of triazine herbicides and some of their main metabolites in water samples has been developed. The proposed CE method includes an off-line solid-phase extraction (SPE) procedure with LiChrolut EN sorbent coupled to a non-aqueous capillary electrophoresis (NACE) separation with UV detection. The target compounds were the chloro-s-triazines simazine, atrazine, propazine; the methyltio-s-triazines ametryn and prometryn and three main derivatives from the atrazine degradation products; namely, deethylatrazine, deethylhydroxyatrazine and deisopropylhydroxyatrazine. The analytical characteristics of the CE method are reported. The repeatability of the method was studied considering the different steps of the method separately in order to determine the contributions of each step to the total variability of the method. The NACE-UV results are compared with those obtained with a high performance liquid chromatography with UV detection (HPLC-UV) method. The same off-line SPE procedure was applied to both techniques. The results obtained show that both methods afford the same results in the analysis of surface and drinking water samples, with a level of significance regarding the F- and t-tests greater than 0.05 in all the cases. The detection limits in surface water samples were in the 0.04-0.32 microg l(-1) and 0.11-1.2 microg l(-1) ranges for the NACE-UV and HPLC-UV methods, respectively. The recoveries (spiked/found) were significantly 100% in all cases.     

Nonaqueous capillary electrophoresis method for the analysis of gleevec and its main metabolite in human urine

The viability of nonaqueous capillary electrophoresis (NACE) was investigated for determination of gleevec and its main metabolite in human urine using a fused-silica capillary. Baseline separation of the studied solutes was obtained using a nonaqueous solution composed of 12 mM ammonium acetate and 87.6 mM acetic acid in methanol-acetonitrile (ACN) (80:20, v:v) providing analysis time shorter than 3 min. Different aspects including stability of the solutions, linearity, accuracy and precision were studied in order to validate the method in the urine matrix. Detection limits of 24 microg L(-1) for gleevec and its metabolite were obtained. A robustness test of the method was carried out using the Plackett-Burman fractional factorial model with a matrix of 15 experiments. The developed method is simple, rapid and sensitive and has been used to determine gleveec and its metabolite at clinically relevant levels in human urine. Before NACE determination, a solid-phase extraction (SPE) procedure with a C18 cartridge was necessary. Real determination of these analytes in two patient urines were done.     

Analysis of herbicides in water using temperature-responsive chromatography and an aqueous mobile phase

A simple and rapid method has been developed for herbicides in water using temperature-responsive liquid chromatography (LC) and a column packed with poly(N-isopropylacrylamide) (PNIPAAm), a polymer anchored on the stationary-phase surface of modified silica. PNIPAAm reversibly changes its hydrophilic/hydrophobic properties in water in response to temperature. The method was used to determine five sulfonylurea and three urea herbicides. Separation was achieved with a 10 mM ammonium acetate (pH 3.0) isocratic aqueous mobile phase, and by changing the column temperature. The analytes were extracted from water by off-line solid-phase extraction (SPE) with an N-vinyl-pyrrolidone polymer cartridge. The average recoveries of the eight herbicides from spiked pure water, tap water and river water were 70-130% with relative standard deviations (RSDs) of <10%. The limits of quantitation (LOQ) of the eight herbicides were between 1 and 4 microg l(-1).