多频与宽频超材料吸收器

提出了多频与宽频超材料吸收器结构模型, 该吸收器是由刻蚀在介质基板两面的金属图案组成, 其正面是由不同大小的金属铜圆片和金属铜圆环结构组合而成, 反面完全覆盖金属铜. 由于不同几何大小的圆片或圆环结构的谐振频率不同, 且是相互独立的. 因此通过将两种不同几何大小的圆片与圆环结构组合, 使其在不同频率谐振, 便可得到双频吸收器; 而将三种不同几何大小的圆片和圆环结构组合便可得到三频吸收器; 同理可得到四频吸收器. 同时, 通过研究吸收器的电场分布, 验证了不同几何大小的圆片或圆环结构在不同频率谐振. 若通过优化组合圆片和圆环结构, 使其谐振频率紧密相连则可得到宽频吸收器. 关键词： 吸收器 超材料 多频 宽频     

A broadband,polarisation-insensitive and wide-angle coplanar terahertz metamaterial absorber

Broadband terahertz metamaterial absorbers have attracted considerable attention due totheir significant potential for practical applications. These absorbers are usuallystacked in several differently shaped or sized subunits to form a unit cell, making theirfabrication quite troublesome. A simple design for broadband metamaterial absorbers istherefore urgently needed. Herein, we propose a coplanar broadband andpolarisation-insensitive perfect absorber formed by two patterned square metallic ringswith a dielectric layer on top of a metallic ground plane. The full width at half maximum(FWHM) of the device can be up to 42% (with respect to the central frequency), which is 2times greater than that of a single-layered structure. This property is retained well fora very wide range of incident angles. The two patterned square rings resonating atdifferent but similar frequencies leads to the broadband absorption. Moreover, ahybridised resonance model is proposed to analyse the origin of the resonance bandwidth.The results of this metamaterial absorber design appear to be very promising for solarcell, detection and imaging applications.     

基于磁/电介质混合型基体的宽带超材料吸波体的设计与制备

本文设计了一种基于磁/电介质混合型基体的宽带超材料吸波体, 吸波体基本单元由电阻膜、磁/电介质混合型基体以及金属背板组成. 采用时域有限差分法对超材料吸波体吸波性能进行了仿真, 使用遗传算法优化了反射率小于-10 dB的带宽. 仿真结果表明, 当超材料吸波体厚度为2.5 mm时, 在7.8–18 GHz频率范围内的反射率小于-10 dB, 具有厚度薄、宽带、极化不敏感等优点. 通过等效电路模型对其工作机理进行了分析与讨论. 最后制备样品进行测试, 测试结果与仿真结果一致.     

基于超材料的偏振不敏感太赫兹宽带吸波体设计

本文设计了一种基于超材料的偏振不敏感太赫兹宽带吸波体.吸波体包含两层金属和一层中间介质,表面金属层每一个周期单元由五种尺寸接近的金属块按照相邻不同的规律排列成5×5的方形阵列.各种尺寸金属块分别产生单峰谐振吸收,五个谐振吸收峰相互靠近从而产生宽带吸收.通过研究吸波体表面电流和电场z分量分布情况可知,入射太赫兹能量的吸收主要是由y方向上电场引起的电偶极子振荡和z方向上磁场引起的磁极化产生,而且金属层的欧姆损耗起主要作用.仿真结果表明,吸波体吸收率在80%以上的带宽约为1.2 THz,最高吸收率可达98.7%,半峰全宽(FWHM)为1.6 THz,该宽带吸波体的厚度约为中心波长的二十分之一,对偏振方向不敏感,且能实现大角度吸收,在太赫兹频段的电磁隐身、测辐射热探测器以及宽带通信等领域有潜在的应用价值.     

Polarization-Independent Broadband Optical Regime Metamaterial Absorber for Solar Harvesting: A Numerical Approach

In this article, a broadband metamaterial (MTM) absorber is proposed that exhibits near-unity absorption in the terahertz regime. The proposed metamaterial absorber was initiated on a quartz (fused) substrate, whereas the resonator and backplane are constructed with tungsten. The resonator is designed with a square ring loaded with a face-to-face E structure at the center. It also consists of diagonally extended arrow-like shapes loaded from the corners and a concave-shaped structure extended from the middle of the square ring. Near-perfect absorption is observed at the frequencies of 465.2 THz, 585.2 THz, 648.8 THz, and 762.8 THz with absorption peaks of 99.8%, 99.9%, 99.92%, and 99.92%, respectively. Moreover, it exhibits broadband absorption properties above 90% absorption with bandwidths 20.4 THz, 80.8 THz, 41.6 THz, and 90 THz, respectively, at these resonance frequencies. Due to its symmetrical structure, it shows polarization-insensitivity behavior up to 90° with maximum absorption greater than 90% both in transverse (TE) and transverse magnetic (TM) modes. It also exhibits insensitivity to changes of incident angle from 0°–45°. Metamaterial properties of the proposed absorber are also analyzed, showing single negative behavior. Absorber property has been examined through surface current and equivalent circuit electric and magnetic field analysis. The effect of the cross-polarization is negligible and is verified through simulation. Due to its large bandwidth, polarization-insensitive behavior, and low PCR, the proposed MTM absorber can be incorporated into photovoltaic devices as a solar-energy harvester.     

基于石墨烯和二氧化钒的太赫兹宽带可调谐超材料吸收器

太赫兹超材料吸收器作为一种重要的太赫兹功能器件,被广泛应用于生物医学传感、电磁隐身、军用雷达等多个领域.但这种传统的超材料吸收器结构具有可调谐性差、功能单一、性能指标不足等缺点,已经无法满足复杂多变的电磁环境的要求,因此可调谐超材料吸收器逐渐成为了太赫兹功能器件领域的研究热点.为实现超材料吸收器吸收特性的调谐,通常从调...     

宽带透射吸收极化无关超材料吸波体

提出了一种新的基于磁性吸波体材料的具有低频透射和高频宽带吸收特性的超材料吸波体.该超材料吸波体在1 GHz的透射系数为-0.5 dB,具有较好的低频透射特性,可以实现对低频信号的相互通信;在频率大于8.4 GHz的频段,吸收率均大于80%,基本覆盖整个X波段和Ku波段,实现高频宽带吸收.此外,由于该超材料吸波体的单元金属周期结构具有较好的四重旋转对称性,因而是极化无关的.该透射吸收超材料吸波体设计简单,实用性强,具有较强的潜在应用价值.     

Engineering the dispersion of metamaterial surface for broadband infrared absorption

We propose a broadband infrared absorber by engineering the frequency dispersion of metamaterial surface (metasurface) to mimic an ideal absorbing sheet. With a thin layer of structured nichrome, a polarization-independent absorber with absorption larger than 97% is numerically demonstrated over a larger than one octave bandwidth. It is shown that the bandwidth enhancement is related with the transformation of the Drude model of free electron gas in metal film to the Lorentz oscillator model of a bound electron in the structured metallic surface. We believe that the concept of dispersion engineering may provide helpful guidance for the design of a broadband absorber.     

Solar broadband metamaterial perfect absorber based on dielectric resonant structure of Ge cone array and InAs film

The broadband metamaterial perfect absorber has been extensively studied due to its excellent characteristics and promising application prospect. In this work a solar broadband metamaterial perfect absorber is proposed based on the structure of the germanium (Ge) cone array and the indium arsenide (InAs) dielectric film on the gold (Au) substrate. The results show that the absorption covers the whole ultraviolet-visible and near-infrared range. For the case of A > 99%, the absorption bandwidth reaches up to 1230 nm with a wavelength range varied from 200 nm to 1430 nm. The proposed absorber is able to absorb more than 98.7% of the solar energy in a solar spectrum from 200 nm to 3000 nm. The electromagnetic dipole resonance and the high-order modes of the Ge cone couple strongly to the incident optical field, which introduces a strong coupling with the solar radiation and produces an ultra-broadband absorption. The absorption spectrum can be feasibly manipulated via tuning the structural parameters, and the polarization insensitivity performance is particularly excellent. The proposed absorber can possess wide applications in active photoelectric effects, thermion modulators, and photoelectric detectors.     

Tunable broadband metamaterial absorber consisting of ferrite slabs and a copper wire

A tunable broadband metamaterial absorber is demonstrated at microwave frequencies in this paper.The metamaterial absorber is composed of ferrite slabs with large resonance beamwidths and a copper wire.The theoretical analysis for the effective media parameters is presented to show the mechanism for achieving the perfect absorptivity characteristic.The numerical results of transmission,reflectance,and absorptivity indicate that the metamaterial absorber exhibits a near perfect impedance-match to free space and a high absorptivity of 98.2% for one layer and 99.97% for two layers at 9.9 GHz.The bandwidth with the absorptivity above 90% is about 2.3 GHz.Moreover,the absorption band can be shifted linearly in a wide frequency range by adjusting the magnetic bias.This metamaterial absorber opens a way to prepare perfectly matched layers for engineering applications.     

Ultra-broadband metamaterial absorber for infrared transparency window of the atmosphere

The broadband absorber at the wavelength range from 8 to 13 μm has attracted much attention because this range is exactly the infrared transparency window of the atmosphere. In this Letter, we propose a new structure of ultra-broadband absorber, which is composed of a periodic array of single-sized titanium (Ti) patches and a sandwich (Ti/SiO₂/Ti) plane. In the infrared transparency window of the atmosphere, the structure proposed can achieve nearly perfect absorption with the maximal absorptivity up to 99% for the wavelength range from 9.77 to 10.69 μm, and a high average absorptivity of 96.7% from 8 to 13 μm. The strongly localized electric field, at the interface of the top thin Ti film and the dielectric spacer of sandwich plane, leads to the ultra-broadband high absorption. In addition, this structure demonstrates the insensitivity of polarization and oblique angle. This metamaterial absorber with high performances in both bandwidth and absorptivity shows a promising prospect in applications such as thermal emitters, thermal coolers, and infrared sensors.     

3D broadband isotropic NRI metamaterial based on metallic cross-pairs

In this paper, a new type of 3D metamaterial composed of double periodic array of metallic cross-pairs printed on the six sides of a cubic dielectric substrate was proposed to obtain the characteristics of broadband NRI and isotropy for the applications of super lenses. The behaviors of NRI, isotropy and polarization were analyzed using the CST Microwave Studio. The results show that the proposed metamaterial exhibits not only a broadband NRI whose relative bandwidth can be up to 56.7%, but also polarization-independence and isotropy. Thus, the proposed metamaterial is a good candidate material for 3D broadband isotropic NRI metamaterial.     

A simple design of ultra-broadband and polarization insensitive terahertz metamaterial absorber

Ultra-broadband metamaterial absorbers have attracted considerable attention due to their great prospect for practical applications. These absorbers are usually stacked by many (no. <20) different shaped or sized subunits in a unit cell, making it quite troublesome to be fabricated. Simple design for ultra-broadband absorber is urgently necessary. Herein, we propose a simple design of ultra-broadband and polarization insensitive terahertz metamaterial absorber based on a double-layered composite structure on a metallic board, and each layer consists of two sets of different sized square metallic plates. Greater than 90 % absorption is obtained across a frequency range of 0.85 THz with the central frequency around 1.60 THz. The relative absorption bandwidth of the device is greatly improved to 53.3 %, which is much larger than previous results. The mechanism of the ultra-broadband absorber is attributed to the overlapping of four closely resonance frequencies. The proposed metamaterial absorber has potential applications in detection, imaging and stealth technology.     

Design and model of wideband absorber made of ultrathin metamaterial structures

A planar microwave ultrathin broadband absorber is proposed. It is composed of metallic patterns arranged on a dielectric material which is backed by a copper plate. The patterns of different dimensions allow to judiciously design absorption peaks at specific frequencies of interest. These peaks are due to the mode resonances of the cavities formed by the metallic patches, the dielectric substrate and the copper plate. In order to widen the absorption bandwidth, patterns of different dimensions are used, together with the different modes of these cavities. Numerical and experimental results are presented to validate the proposed method at microwave frequencies. It is also shown that the use of a composite air dielectric substrate supporting the metallic patterns helps to increase the absorption level.     

基于电磁谐振分离的宽带低雷达截面超材料吸波体

基于超材料的电磁谐振特性, 设计、制作了一种极化无关的宽带低雷达散射截面 (radar cross section, RCS)超材料吸波体. 通过场分布和反演法分析了其吸波机理, 利用波导法和空间波法测试了其吸波率和RCS特性. 理论分析表明: 在平面波的作用下, 该吸波体对某一吸波频率在不同的位置分别提供电谐振和磁谐振, 对不同的吸波频率, 利用不同的介质层提供主要的能量损耗, 从而有效减弱了电磁耦合, 保证了宽频带的强吸收特性. 实验结果表明: 设计的三层结构吸波体吸波率达90%以上的带宽是单层结构的4.25倍, RCS减缩10 dB以上的带宽为5.1%, 其单元尺寸为0.17λ, 厚度仅为0.015λ. 该吸波体的低RCS特性还具有极化无关、宽入射角的特点, 且通过改变吸波体的夹层结构可以实现工作带宽的灵活调节. 关键词： 超材料吸波体 雷达散射截面 宽带 电磁谐振     

Broadband and ultra-low reflection metamaterial absorber embedded with magnetic materials

In this study, we design, prepare and characterize a broadband, ultra-low reflectivity and incidence angle-insensitive metamaterial absorber. The design of this absorber not only provides a novel idea for the design of broadband absorbers, but also enhances the application prospects of metamaterial absorbers. By introducing FeSiAlp/epoxy magnetic composite and optimizing the structural parameters, the absorption performance of the metamaterial absorber has been significantly improved. The effective absorption bandwidth (bandwidth with reflectivity less than −10dB) is increased by 3.4 times from 2.19 GHz to 7.49 GHz, and the RL_min (minimum reflection loss) value reaches −38.31 dB at 17.83 GHz, that is the absorption rate reaches 99.99%. Meanwhile, the experimental results also verify the simulation design results. Therefore, the absorber not only plays the characteristics of strong absorption of metamaterial, but also absorbs the advantages of broadband of magnetic material.     

Experimental demonstration of terahertz metamaterial absorbers with a broad and flat high absorption band

We present the design, numerical simulations and experimental measurements of terahertz metamaterial absorbers with a broad and flat absorption top over a wide incidence angle range for either transverse electric or transverse magnetic polarization depending on the incident direction. The metamaterial absorber unit cell consists of two sets of structures resonating at different but close frequencies. The overall absorption spectrum is the superposition of individual components and becomes flat at the top over a significant bandwidth. The experimental results are in excellent agreement with numerical simulations.     

低雷达散射截面的超薄宽带完美吸波屏设计研究

提出了一种基于PMA单元结构的超薄宽带完美吸波屏设计方法. 该方法将多层拓展带宽的技术与单层多谐振方法有机结合, 实现带宽拓展的同时, 保持了完美吸波屏结构简单、无集总元件的特点, 易于实际加工和应用. 以双层三谐振超薄宽带完美吸波屏为例, 结合其等效电路, 理论上验证了所设计吸波屏的吸波机理, 同时验证了方法的有效性. 仿真分析该吸波屏具有低雷达散射截面、极化不敏感和宽入射角的特征. 仿真和实测结果表明: 该吸波屏在厚度为0.01 λ的条件下, 具有14.1%的半波功率带宽;-3 dBsm的雷达散射截面缩减带宽为18.9%, 在法线方向的最大缩减量为23 dBsm, 在法向±40°内具有较好的雷达散射截面减缩效果. 关键词： 完美吸波屏 宽带 雷达散射截面 等效电路     

Dual-band metamaterial with windmill-like structure

A broadband negative refractive index metamaterial based on a windmill-like structure is proposed, and investigated numerically and experimentally at the microwave frequency range. From the numerical and experimental results, effect media parameters are retrieved, which clearly show that there exist two broad frequency bands in which the permittivity and permeability are negative. The two negative bands are from 9.1 GHz to 10.5 GHz and from 12.05 GHz to 14.65 GHz respectively, and the negative bandwidth is 4 GHz. Due to the good bandwidth performance, the metallic cell with double negative property obtained in this paper is suitable for use in the design of multiband or broadband microwave devices.     

Dual-band metamaterial with a windmill-like structure

A broadband negative refractive index metamaterial based on a windmill-like structure is proposed, and investigated numerically and experimentally at the microwave frequency range. From the numerical and experimental results, effect media parameters are retrieved, which clearly show that two broad frequency bands exist in which the permittivity and permeability are negative. The two negative bands are from 9.1 GHz to 10.5 GHz and from 12.05 GHz to 14.65 GHz respectively, and the negative bandwidth is 4 GHz. Due to the good bandwidth performance, the metallic cell with double negative property obtained in this paper is suitable for use in the design of multiband or broadband microwave devices.