流动注射化学发光法测定佐米曲谱坦

在碱性条件下,佐米曲谱坦对鲁米诺-K3[Fe(CN)6]化学发光体系有较强的抑制作用,据此建立了佐米曲谱坦的流动注射化学发光分析法。该法的化学发光抑制值ΔI与佐米曲谱坦质量浓度在2.0×10-6~1.2×10-4g/mL范围内,呈良好的线性关系,检出限为7.6×10-7g/mL。对2.5×10-5g/mL佐米曲谱坦测定的相对标准偏差为1.2%(n=11)。方法适用于佐米曲谱坦片中佐米曲谱坦的测定。     

流动注射化学发光法测定那格列奈

在碱性介质中,那格列奈对Luminol-H2O2体系的化学发光有很强的抑制作用,据此建立了流动注射化学发光抑制法测定那格列奈的新方法.该法的化学发光抑制值△I与那格列奈的质量浓度在2.0×10-8～1.0×10-6 g/mL范围内,呈良好的线性关系,检出限为1.4×10-8 g/mL;对4.0×10-7 g/mL那格列奈连续进行11次平行测定,相对标准偏差为1.0%;通过对荧光光谱的研究,对机理进行了初步探讨.     

快速化学发光联用流动注射技术测定西咪替丁

在NaOH-NaHCO3介质中,铁氰化钾氧化西咪替丁产生快速化学发光反应,0.5 s后发光达到最大,2 s后迅速衰减至零。本文结合流动注射技术,建立了一种化学发光测定西咪替丁的新方法。针对这一快速发光反应,设计了与之相应的管路系统和最短的反应管道来捕捉最大化学发光信号,发光强度与西咪替丁质量浓度在5×10-7~1×10-4g/mL范围内呈线性关系,检出限为1.1×10-7g/mL。对5×10-6g/mL西咪替丁进行11次平行测定,相对标准偏差为1.8%。本法已用于西咪替丁片剂的测定。     

Indirect ultraviolet determination of silver with nickelocyanide ion by flow injection analysis

A flow-injection method for the ultraviolet spectrophotometric determination of silver, based on its reaction with nickelocyanide ion, Ni(CN)²⁻₄, in ammoniacal buffer medium (pH 10) and subsequent measurement of the decrease in the absorption of the Ni(CN)²⁻₄ complex at 275 nm is described. The calibration graph is linear in the range 10–400 μm silver. At a sampling rate of about 60 samples h⁻¹ with 35 μl sample injections, precision was about 1% relative standard deviation. The proposed method was successfully applied to the determination of silver in some common silver minerals.     

流动注射光度法直接测定海水中的微量苯胺

基于苯胺与亚硝酸盐的重氮化反应及反应产物与甲萘酚的显色,借助流动分析技术,实现了海水中苯胺含量的分析测定。体系以30.9g/L的NaCl做载液、人工海水配制标准样品,对各个影响因素进行了优化。苯胺浓度在0.01～1.0mg/L范围内与相对峰高呈线性关系,线性方程ΔH(mV)=200.53ρ+1.0728(n=8,ρ为苯胺浓度mg/L),相关系数R2=0.9982。方法的检出限(3σ)为0.005mg/L,相对标准偏差(RSD)为4.8%(n=11)。考察了共存离子、不同盐度样品对分析测定的影响。用于实际海水样品的分析,回收率为95.8%～106.6%。     

流动注射化学发光法测定痕量NO_2~-的研究与应用

Based on the principle of the reaction of NO2-with I-and formation of I2 in HCl solution,and the chemiluminescence(CL) reaction between luminol and I2 in an alkaline medium.A fairly sensitive,simple and rapid flow-injection analysis-chemiluminescence method for the determina-tion of trace nitrite with the luminal-I——NO2-coupling luminescence system has been developed.Experiment conditions of flow-injection analysis are optimized.When satisfying the condition that Luminol as 4.0×10-4 mol/L,0.7 % KI,0.04 mol/...     

Rapid determination of lead extracted by acetic acid from glazed ceramic surfaces by flow injection on-line preconcentration and spectrophotometric detection

A rapid method has been developed for the determination of lead extracted by acetic acid from glazed ceramic surfaces by flow injection analysis without any pretreatment. An aliquot of 4% acetic acid solution, which has been kept in a teacup for 24 h in the dark, is injected into a carrier solution (1 M nitric acid) and passed through a Pb-Spec resin column. After washing the column with an ammonium nitrate solution, the lead adsorbed on the column is eluted with an ammonium oxalate solution and then merged with a 4-(2-pyridylazo)resorcinol (PAR) solution, followed by measurement of the absorbance of the lead-PAR complex at 530 nm. The detection limit, concentration giving a signal equal to three times the standard deviation of the blank signal, is 8 ng ml⁻¹. The relative standard deviation of measurements at the 0.8 μg ml⁻¹ level is 0.35% (n = 5). The sample throughput is 12 per hour.     

Sensitive determination of captopril by flow injection analysis with chemiluminescence detection based on the enhancement of the luminol reaction

This work reports a novel flow injection (FI) method for the determination of captopril, 1-[(2S)-3-mercapto-2-methylpropionyl]-l-proline (CPL), based on the enhancement CPL affords on the chemiluminescence (CL) reaction between luminol and hydrogen peroxide. For this purpose alkaline luminol and hydrogen peroxide solutions were mixed online, the sample containing CPL was injected into an aqueous carrier stream, mixed with the luminol-hydrogen peroxide stream and pumped into a glass flow cell positioned in front of a photomultiplier tube (PMT). The increase in the CL intensity was recorded in the form of FI peaks, the height of which was related to the CPL mass concentration in the sample. Different chemical and instrumental parameters affecting the CL response were investigated. Under the selected conditions, the log-log calibration curve was linear in the range 5-5000 μg l⁻¹ of CPL, the limit of detection was 2 μg l⁻¹ (at the 3σ level), the R.S.D., s_r was 3.1% at the 100 μg l⁻¹ level (n=8) and the sampling rate was 180 injections h⁻¹. The method was applied to the determination of CPL in pharmaceutical formulations with recoveries in the range 100±3%.     

Improved method for shipboard determination of iron in seawater by flow injection analysis

A flow injection analysis (FIA) catalytic spectrophotometric method for the determination of dissolved iron in seawater was further developed to yield a more sensitive assay with a low detection limit. The method employs an initial sample acidification step followed by an iron pre-concentration step involving an in-line 8-hydroxy-quinoline (8-HQ) metal-chelating resin column. The copper capacity and elution efficiency, as well as the iron FIA performance of three trace-metal clean resins were compared, resulting in the selection of a clean silica gel support for the 8-HQ ligand. The concentrated sample is eluted from the resin with an acidic carrier and mixed with reagents, initiating an iron-catalyzed, color-forming reaction. Increasing the reaction temperature from 18 to 30 °C doubled the sensitivity; reaction temperature control was necessary to obtain good reproducibility in the field. Reagent blanks were as low as 0.05 nM and a detection limit of 0.016 nM was obtained from three times the S.D. of a 0.06 nM seawater sample repeated six times. A 0.06 nM detection limit was calculated from shipboard experiments where total dissolved iron was determined for 10 different samples from the same station. The instrumental sensitivity and precision evolved to the point where the blank associated with the technique is the major factor influencing its detection limit.     

奋乃静的流动注射分光光度分析

基于在H2SO4介质中，K2S2O8氧化奋乃静生成红色中间产物的原理，建立了流动注射分光光度法测定药物中奋乃静含量的新方法。利用单纯形优化法选择了最佳实验条件。方法的线性范围为20-170μg/mL，检出限为0．46μg/mL，进样频率为150h。该方法用于奋乃静片剂中奋乃静含量的测定，其测定结果与药典法对照，无显著性差异。     

On-line determination of mercury(II) by membrane separation flow injection analysis

A rapid and inexpensive gas-diffusion (GD) flow injection method for the on-line determination of Hg(II) in aqueous samples is described. The analytical procedure involves the injection of a Hg(II) sample into a 1.5 M H₂SO₄ carrier stream which is merged with a reagent stream containing 0.6% SnCl₂ and 1.5 M H₂SO₄. Under these conditions Hg(II) is reduced to metallic mercury which partially evaporates through a Teflon membrane into an acceptor stream containing 1.75×10⁻⁴ M KMnO₄ in 0.3 M H₂SO₄. The decrease in the absorbance of the acceptor stream at 528 nm corresponding to the absorption maximum of the permanganate anion can be related to the original concentration of Hg(II) in the sample. The method is characterized by a detection limit of 4 μg l⁻¹ and a sampling frequency of 8 h⁻¹. The flow system was successfully applied to the analysis of river samples spiked with Hg(II).     

On-line determination of cyanide in the presence of sulfide by flow injection with pervaporation

A pervaporation-flow injection (PFI) method is described for the analysis of cyanide in the presence of sulfide. The interfering sulfide ion in the injected sample is precipitated on-line using an acidified lead nitrate reagent solution before the donor stream enters the pervaporation cell. Using amperometric detection at a silver electrode set at −50 mV (vs Ag/AgCl), linear calibration was obtained in the range 0.02–100.0 mg l⁻¹ with a detection limit of 1.0 μg l⁻¹. Sample throughput was of the order of 12–15 h⁻¹. When the method was applied to the analysis of synthetic samples, there was no significant interference from sulfide at concentrations up to 50 mg l⁻¹. Thiocyanate did not interfere at levels up to 1000 mg l⁻¹. When applied to industrial samples containing sulfide and thiocyanate ions where the cyanide ions are predominantly complexed with various metal ions the PFI method was found to give results close to those obtained by standard distillation methods for weak acid dissociable (WAD) cyanide.     

Sensitive and selective determination of molybdenum by flow injection chemiluminescence method combined with controlled potential electrolysis technique

A sensitive and selective flow injection chemiluminescence (CL) method combined with controlled potential electrolysis technique was described for the determination of molybdenum. The method is based on the chemiluminescence reaction of luminol with unstable molybdenum(III) in alkaline solution. The molybdenum(III) was on-line reduced from molybdenum(VI) via controlled potential electrolysis technique using a homemade flow-through carbon electrolytic cell at the potential of −0.6 V (versus Ag/AgCl). The method allows the determination of molybdenum in the 5.0×10⁻¹⁰ to 5.0×10⁻⁷ g ml⁻¹ range with a limit of detection (3σ) of 5×10⁻¹¹ g ml⁻¹ molybdenum. The relative standard deviation is 2.6% for the 1.0×10⁻⁹ g ml⁻¹ molybdenum solution in 11 repeated measurements. This method was successfully applied to the determination of molybdenum in water samples.     

Non-extraction flow injection determination of cationic surfactants using eriochrome black-T

A new, rapid, sensitive, non-extraction batch, and flow injection spectrophotometric method for the determination of cationic surfactants (CSs) such as cetyltrimethyl ammonium bromide (CTAB), tetra-n-butyl ammonium chloride (TBAC) and cetylpyridinium chloride (CPC) is proposed. The method is based on the interaction of cationic surfactants with eriochrome black-T to form an ion-association complex. This complex has strong absorbance at 708 nm. The effects of chemical parameters and FIA variables on the determination of cationic surfactants were studied in detail, especially for CTAB. Under optimum conditions, the two linear calibration ranges of the method are 3.0 × 10⁻⁶ to 5.0 × 10⁻³ mol L⁻¹ CTAB, CPB and DTAB for the batch spectrophotometric method and 2.0 × 10⁻⁶ to 2.0 × 10⁻⁴ mol L⁻¹ CTAB, CPB and TBC for the flow injection spectrophotometric method. The sample throughput was 35 ± 5 samples h⁻¹ at room temperature. The relative standard deviations for 10 replicates of analysis of (2.0, 0.6 and 0.2) × 10⁻⁴ mol L⁻¹ CTAB were 1.2, 1.3, and 0.8%, respectively. In addition, the influence of potential interfering substances on the determination of cationic surfactants was studied. The proposed method is simple and rapid, using no toxic organic solvents. It was applied to the determination of trace CS in industrial wastewater with satisfactory results.     

Reversed flow injection and sandwich sequential injection methods for the spectrophotometric determination of copper(II) with cuprizone

Two new flow methods, flow injection analysis (FIA) and sequential injection analysis (SIA), for the spectrophotometric determination of Cu(II) in water at trace levels have been developed and optimised. Both methods are based on the reaction with oxalic acid bis(cyclohexylidene hydrazide) (cuprizone) in alkaline media. The two procedures have been developed for the final aim to compare their performances and to offer new rapid heavy metals analysis tools, avoiding the use of extraction steps. A detailed study of the physico-chemical parameters affecting the systems performances has been carried out. The reversed FIA and sandwich SIA approaches offered the best sensitivity. In both cases, an extremely good linearity has been obtained within the range 0.06-4 μg ml⁻¹ (correlation coefficient r=0.9999), whereas the observed detection limits were 0.013 and 0.004 μg ml⁻¹, for FIA and SIA, respectively. Furthermore, due to the great similarity of the diffusion zones in the reaction slugs, our approach offers the opportunity to compare the two methods in analogous conditions. This SIA method, besides keeping its typical reagent saving features, offered analytical performances equivalent to those of FIA. To obtain these results, an original “stop-flow like” method was successfully employed in the SIA approach. Both methods were validated by analysis of real water samples, after copper addition, and certified reference samples of fortified and waste waters.     

反向流动注射化学发光法测定二邻苯二甲酰亚胺甲基二磺酸基酞菁锌

在碱性介质中 ,二邻苯二甲酰亚胺甲基二磺酸基酞菁锌 (简写为ZnPcS2 P2 )可增强Luminol H2 O2 CTAB体系的化学发光 ,据此建立了测定ZnPcS2 P2含量的反向流动注射化学发光分析新方法。用该法测定ZnPcS2 P2 ,其范围为 2 .5× 1 0 - 7～ 1 .0× 1 0 - 8mol/L ,检测限为 9× 1 0 - 9mol/L ,对 1 .0× 1 0 - 7mol/L的Zn PcS2 P2 溶液进行 9次平行测定 ,其相对标准偏差为 1 .2 %。本法有一定的选择性 ,与分光光度法相比 ,灵敏度提高了 1～ 2个数量级。     

流动注射化学发光法测定褪黑素

在强碱性介质中,铁氰化钾可直接氧化褪黑素产生化学发光。基于此,建立了一种测定褪黑素的流动注射化学发光分析方法。线性范围为1.9×10-6~2.3×10-4g/mL,检出限为5×10-7g/mL,该法已用于药物中褪黑素的测定。     

Spectrophotometric determination of total phenolics by solvent extraction and sorbent extraction optosensing using flow injection methodology

Flow injection analysis (FIA) procedures for the Spectrophotometric determination of phenol involving in-line concentration by solvent and sorbent extraction have been developed. The imine product formed in the reaction between phenol and 4-aminoantipyrine (4-AAP) is either extracted into chloroform (solvent extraction) or is temporarily retained on C₁₈-modified silica material contained in a microcolumn (sorbent extraction). In the latter case two variants of detection have been used namely the Spectrophotometric measurement of the methanolic eluent containing the concentrated dye and at-column optosensing of the retained reaction product followed by methanol elution to maintain reversibility of the process. In the solvent extraction procedure a 10-fold increase of sensitivity compared to the common FIA method without extraction is achieved but no corresponding improvement in detectability is observed. Under optimized conditions the detection limit amounts to 8 μg l⁻¹. Using sorbent extraction methodology, high concentration factors can be obtained when large sample volumes are used. The only limitation in getting correspondingly lower detection limits are an increasingly high and variable blank value with sampling volume. The detection limits obtained for measurement of the absorbance in the eluent and on-column optosensing are 11 μg l⁻¹ and 0.4 μg l⁻¹, respectively. A study of the extractability of various phenol derivates using both solvent and sorbent extraction revealed lower relative response rates compared to the FIA method without extraction. Phenolics that possess an additional acidic group are present in ionized form at the high pH of the assay and are not extractable at all.     

流动注射时间扫描荧光分析法测定青霉素V钾

研究了H2SO4颜色反应用于青霉素V钾(PMPP)荧光测定的新方法。PMPP为弱荧光物质,与浓H2SO4反应后荧光显著增强。结合流动注射进样技术,借助时间扫描荧光方式,提出了流动注射时间扫描荧光分析法测定PMPP的新方法。在最大激发236.0 nm、最大发射波长306.0 nm处,PMPP在3.6×10-5g/L~4.0×10-2g/L范围内与荧光强度呈良好的线性关系,相关系数为0.9999。方法检出限为1.0×10-5g/L,相对标准偏差为0.6%(n=11,ρ=1.0×10-3g/L),进样量为0.18 mL。方法已用于药物及尿样中PMPP的测定。     

A potential high-throughput method for the determination of lipase activity by potentiometric flow injection titrations

Potentiometric FIA titrations were performed to determine enzyme activities of lipase type B from Candida antarctica, CAL-B. Two substrates, triacetin and tributyrin were hydrolyzed in phosphate buffer solutions, and the concentration change of the base component of the buffer was titrated in a carrier solution containing hydrochloric acid and potassium chloride. The system was calibrated with butyric acid and acetic acid, respectively. FIA titration peaks were evaluated with respect to peak height and peak area. Butyric acid and acetic acid could be titrated in the buffer solution from 3 × 10⁻³ mol L⁻¹ to 0.1 mol L⁻¹. The detection limit of enzyme activity was determined to be 0.07 U mL⁻¹ (15 min reaction time) and the minimum activity was calculated to be 0.035 units corresponding to 35 nmol min⁻¹. The specific activities of lipase B for the hydrolysis of tributyrin and triacetin were determined as 16 ± 2 U mg⁻¹ and 2 ± 0.2 U mg⁻¹ (per mg commercial lipase preparation), respectively.