Synthesis and characterization of submicron size particles of LiMn<Subscript>2</Subscript>O<Subscript>4</Subscript> by microemulsion route

Among the various positive electrode materials investigated for Li-ion batteries, spinel LiMn₂O₄ is one of the most important materials. Small particles of the active materials facilitate high-rate capability due to large surface to mass ratio and small diffusion path length. The present work involves the synthesis of submicron size particles of LiMn₂O₄ in a quaternary microemulsion medium. The precursor obtained from the reaction is heated at different temperatures in the range from 400 to 900 °C. The samples heated at 800 and 900 °C are found to possess pure spinel phase with particle size <200 nm, as evidenced from XRD, SEM, and TEM studies. The electrochemical characterization studies provide discharge capacity values of about 100 mAh g⁻¹ at C/5 rate, and there is a moderate decrease in capacity by increasing the rate of charge–discharge cycling. Studies also include charge–discharge cycling and ac impedance studies in temperature range from −10 to 40 °C. Impedance data are analyzed with the help of an equivalent circuit and a nonlinear least squares fitting program. From temperature dependence of charge-transfer resistance, a value of 0.62 eV is obtained for the activation energy of Mn³⁺/Mn⁴⁺ redox process, which accompanies the intercalation/deintercalation of the Li⁺ ion in LiMn₂O₄.     

Synthesis and characterization of LiCo<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript>Mn<Subscript>2−<Emphasis Type="Italic">x</Emphasis></Subscript>O<Subscript>4</Subscript> powder by a novel CAM microwave-assisted sol–gel method for Li ion battery

LiMn₂O₄-based spinels are of great interest as positive electrode materials for lithium ion batteries. LiCo _x Mn_2−x O₄ (x = 0.0, 0.1, 0.2, 0.3, and 0.4) spinel phases have been synthesized by novel citric acid-modified microwave-assisted sol–gel method. The structural properties of the synthesized products have been investigated by X-ray powder diffraction and scanning electron microscopy. To improve the recharge capacity of Li/LiCo _x Mn_2−x O₄ cells, the electrochemical features of LiCo _x Mn_2−x O₄ compounds have been evaluated as positive electrode materials. The structural properties of Co-doped oxides are very similar to LiMn₂O₄ electrode. Techniques like cyclic voltammetry, charge–discharge and cycle life are also used to characterize the LiCo _x Mn_2−x O₄ (x = 0.0, 0.1, 0.2, 0.3, and 0.4) electrodes.     

Electrochemical performance of rare-earth doped LiMn<Subscript>2</Subscript>O<Subscript>4</Subscript> spinel cathode materials for Li-ion rechargeable battery

Spinel powders of LiMn_2−x RE _x O₄ (RE = La, Ce, Nd, Sm; 0 ≤ x ≤ 0.1) have been synthesized by solid-phase reaction. The structure and electrochemical properties of these electrode materials were characterized by X-ray diffraction (XRD), cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS) and charge–discharge experiment. The part substitution of rare-earth element RE for Mn in LiMn₂O₄ decreases the lattice parameter, resulting in the improvement of structural stability, and decreases the charge transfer resistance during the electrochemical process of LiMn₂O₄. As a result, the cycle ability, 55 °C high-temperature and high-rate performances of LiMn_2−x RE _x O₄ electrode materials are significantly improved with increasing RE addition, compared to the pristine LiMn₂O₄.     

Electrochemical properties of tetravalent Ti-doped spinel LiMn2O4

Ti-doped spinel LiMn₂O₄ is synthesized by solid-state reaction. The X-ray photoelectron spectroscopy and X-ray diffraction analysis indicate that the structure of the doped sample is Li( Mn^{3 +} Mn_{1 - x} ^{4 +} Ti_x^{4 +} )O₄ {\hbox{Li}}\left( {{\hbox{M}}{{\hbox{n}}^{3 + }}{\hbox{Mn}}_{1 - x\,}^{4 + }{\hbox{Ti}}_x^{4 + }} \right){\hbox{O}}{}_4 . The first principle-based calculation shows that the lattice energy increases as Ti doping content increases, which indicates that Ti doping reinforces the stability of the spinel structure. The galvanostatic charge–discharge results show that the doped sample LiMn_1.97Ti_0.03O₄ exhibits maximum discharge capacity of 135.7 mAh g⁻¹ (C/2 rate). Moreover, after 70 cycles, the capacity retention of LiMn_1.97Ti_0.03O₄ is 95.0% while the undoped sample LiMn₂O₄ shows only 84.6% retention under the same condition. Additionally, as charge–discharge rate increases to 12C, the doped sample delivers the capacity of 107 mAh g⁻¹, which is much higher than that of the undoped sample of only 82 mAh g⁻¹. The significantly enhanced capacity retention and rate capability are attributed to the more stable spinel structure, higher ion diffusion coefficient, and lower charge transfer resistance of the Ti-doped spinel.     

Investigation on LiCoPO<Subscript>4</Subscript> powders as cathode materials annealed under different atmospheres

An uncomplicated Pechini-assisted sol–gel process in aqueous solutions is used for the synthesis of Li–Co phosphate powders as cathode materials. The powders are annealed under different conditions in flowing nitrogen and in flowing air. The structural, morphological, and electrochemical properties are strongly dependent upon the annealing conditions. After the treatment in air, the X-ray diffraction (XRD) patterns reveal the presence of LiCoPO₄ as a single phase. The morphology of the powders consists of a homogeneous and good interconnected blend of grains with different sizes; the cyclic voltammetry (CV) curves show a very good reversibility with very close values of the mean peak maxima in the cathodic region. The electrochemical measurements deliver a discharge specific capacity of 37 mAhg⁻¹ at a discharge rate of C/25 at room temperature. After annealing in nitrogen, the XRD analysis detects the formation of Li₄P₂O₇ and to Co₂P as secondary phases; the morphological investigation indicated that the LiCoPO₄ particles took shape of prisms with an average size of 2 μm. The CV curves are associated with a large polarization and poor irreversibility. The electrochemical measurements deliver a discharge specific capacity of 42 mAh g⁻¹ at a discharge rate of C/25 at room temperature and lower capacity fade (approx. 35%).     

Preparation and electrochemical properties of V<Subscript>2</Subscript>O<Subscript>5</Subscript> submicron-belts synthesized by a sol–gel H<Subscript>2</Subscript>O<Subscript>2</Subscript> route

One-dimensional (1D) submicron-belts of V₂O₅ have been prepared by a sol–gel route using V₂O_5, H₂O₂ and aniline as starting materials. Thermogravimetric and differential thermal analysis, X-ray diffraction, Fourier transform infrared spectroscopy and scanning electron microscopy were employed to characterize the samples. Electrochemical behaviors as cathode material in rechargeable lithium-ion batteries were investigated by galvanostatic charge–discharge measurement and cyclic voltammeter. The results showed that the synthesized V₂O₅ appeared to be submicron-belts and orthorhombic structure. The V₂O₅ submicron-belts exhibited a high initial discharge capacity of 346 mAh/g and stayed 240 mAh/g after 20 cycles at 0.1 C discharge rate in the potential region 1.8–4.0 V.     

Facile preparation and electrochemical properties of large-scale Li<Subscript>1+<Emphasis Type="Italic">x</Emphasis></Subscript>V<Subscript>3</Subscript>O<Subscript>8</Subscript> nanobelts

Large-scale Li_1+x V₃O₈ nanobelts were successfully fabricated using filter paper as deposition substrate through a simple surface sol–gel method. The nanobelts were as long as tens of micrometers with widths of 0.4–1.0 μm and thickness of 50–100 nm. The nanobelts were characterized by X-ray diffration (XRD), Fourier infrared (FT-IR) spectroscopy, scanning electron microscopy (SEM), transmission electron microscopy (TEM). The formation mechanism of the nanobelts was investigated, showing that the morphology of the nanobelts is mainly determined by the calcination temperature. Electrochemical properties of the Li_1+x V₃O₈ nanobelts were characterized by charge–discharge experiments, and the results demonstrate that the Li_1+x V₃O₈ nanobelts exhibit a high discharge capacity (278 mAh g⁻¹) and excellent cycling stability.     

The effect of nanolayer AlF<Subscript>3</Subscript> coating on LiMn<Subscript>2</Subscript>O<Subscript>4</Subscript> cycle life in high temperature for lithium secondary batteries

The surface of the spinel LiMn₂O₄ was coated with AlF₃ by a chemical process to improve its electrochemical performance at high temperatures. The morphology and structure of the original and AlF₃-coated LiMn₂O₄ samples were characterized by X-ray diffraction (XRD), transmission electron microscope (TEM). All the samples exhibited a pure cubic spinel structure without any impurities in the XRD patterns. It was found that the surfaces of the original LiMn₂O₄ samples were covered with a nanolayer AlF₃ after the treatment. The charge/discharge of the materials were carried at 220 mA/g in the range of 3.0 and 4.4 V at 55°C. While the original LiMn₂O₄ showed 17.8% capacity loss in 50 cycles at 55°C, the AlF₃-coated LiMn₂O₄ (118.1 mA h/g) showed only 3.4% loss of the initial capacity (122.3 mA h/g) at 55°C. It is obvious that the improvement in cycling performance of the coated-LiMn₂O₄ electrode at 55°C is attributed to the presence of AlF₃ on the surface of LiMn₂O₄. Published in Russian in Elektrokhimiya, 2009, Vol. 45, No. 7, pp. 817–819. The article is published in the original     

Electrochemical performance of LiVPO<Subscript>4</Subscript>F/C composite cathode prepared through amorphous vanadium phosphorus oxide intermediate

LiVPO₄F/C composites with better electrochemical performance were prepared by calcination of LiF and amorphous vanadium phosphorus oxide (VPO) intermediate synthesized by a sol–gel method using H₃PO₄, V₂O₅ and citric acid as raw materials. The properties of LiVPO₄F/C composites were investigated by X-ray diffraction (XRD), scanning electron microscopy (SEM) and electrochemical tests. The analysis of XRD patterns and Fourier transform infrared spectra (FTIR) reveal that VPO intermediate prepared by sol–gel method is amorphous and VPO₄ may exist in VPO intermediate. The compositions of LiVPO₄F/C composites are related to the calcination temperature for preparation of amorphous VPO/C intermediate and LiVPO₄F/C composite prepared by VPO/C synthesized at 700°C consists of a single crystal phase of LiVPO₄F. The electrochemical tests show that LiVPO₄F/C composite prepared by VPO/C synthesized at 700°C exhibits higher discharge capacity and excellent cycle performance. This LiVPO₄F/C composite displays discharge capacity of 133 mAh g⁻¹ at 0.5 C (78 mA g⁻¹) and remains capacity retention of 96.8% after 30 cycles, even at a high rate of 5 C, the composite exhibits high discharge capacity of 115 mAh g⁻¹ and capacity retention of 97% after 100 cycles.     

Effects of Ni-ion doping on electrochemical characteristics of spinel LiMn<Subscript>2</Subscript>O<Subscript>4</Subscript> powders prepared by a spray-drying method

Spinel LiMn_2−x Ni _x O₄ compounds doped with a range of Ni (x=0–0.06) were synthesized by a spray-drying method. The structure and morphology characteristics of the powders were studied in detail by means of X-ray diffraction (XRD), scanning electron microscopy, and transmission electron microscopy. The XRD data reveal that all the samples have well-defined spinel structure, but, with the increase in Ni content, the doped lithium manganese spinels have smaller lattice constant. The undoped and doped spinel LiMn₂O₄ particles are fine, narrowly distributed, and well crystallized. The electrochemical characteristics of the samples are measured in the coin-type cells in a potential range of 3.2–4.35 V vs Li/Li⁺. All cyclic voltammogram curves exhibit two pairs of redox reaction peaks, but, among them, there are some differences about the peak split. With the increase in the Ni content, the specific capacities of the samples decrease slightly, but their cyclic ability increases.     

One-step hydrothermal synthesis of LiMn2O4 cathode materials for rechargeable lithium batteries

LiMn₂O₄ cathode materials with high discharge capacity and good cyclic stability were prepared by a simple one-step hydrothermal treatment of KMnO₄, aniline and LiOH solutions at 120–180 °C for 24 h. The aniline/KMnO₄ molar ratio (R) and hydrothermal temperature exhibited an obvious influence on the component and phase structures of the resulting product. The precursor KMnO₄ was firstly reduced to birnessite when R was less than 0.2:1 at 120–150 °C. Pure-phased LiMn₂O₄ was formed when R was 0.2:1, and the LiMn₂O₄ was further reduced to Mn₃O₄ when R was kept in the range of 0.2–0.3 at 120–150 °C. Moreover, LiMn₂O₄ was fabricated when R was 0.15:1 at 180 °C. Octahedron-like LiMn₂O₄ about 300 nm was prepared at 120 °C, and particle size decreased with an increase in hydrothermal temperature. Especially, LiMn₂O₄ synthesized at 150 °C exhibited the best electrochemical performance with the highest initial discharge capacity of 127.4 mAh g⁻¹ and cycling capacity of 106.1 mAh g⁻¹ after 100 cycles. The high discharge capacity and cycling stability of the as-prepared LiMn₂O₄ cathode for rechargeable lithium batteries were ascribed to the appropriate particle size and larger cell volume.     

Synthesis and electrochemical properties of yttrium-doped LiMn<Subscript>0.98</Subscript>Y<Subscript>0.02</Subscript>O<Subscript>2</Subscript> for lithium secondary batteries

Yttrium-doped lithium manganese oxide (LiMn_0.98Y_0.02O₂) was prepared by ion exchange of lithium for sodium in NaMn_0.98Y_0.02O₂ precursors obtained by using rheological phase reaction method. This material had small particle size, which was composed of grain size of about 100 nm. Especially, LiMn_0.98Y_0.02O₂ delivered the initial discharge capacity of about 191 mA h g⁻¹ at room temperature when cycled between 2.0 and 4.4 V vs Li/Li⁺. Moreover, it showed an excellent cycling behavior, its specific capacity remained above 173 mA h g⁻¹ after 20 cycles, and the material did not transform into spinel structure during the electrochemical cycling according to the cyclic voltammograms and X-ray powder diffraction. The electrochemical results revealed that the doping of Y³⁺ improved the performance of LiMnO₂ considerably.     

Synthesis and characterization of macroporous Li<Subscript>3</Subscript>V<Subscript>2</Subscript>(PO<Subscript>4</Subscript>)<Subscript>3</Subscript>/C composites as cathode materials for Li-ion batteries

The macroporous Li₃V₂(PO₄)₃/C composite was synthesized by oxalic acid-assisted carbon thermal reaction, and the common Li₃V₂(PO₄)₃/C composite was also prepared for comparison. These samples were characterized by X-ray diffraction (XRD), scanning electron microscope (SEM), and electrochemical performance tests. Based on XRD and SEM results, the sample has monoclinic structure and macroporous morphology when oxalic acid is introduced. Electrochemical tests show that the macroporous Li₃V₂(PO₄)₃/C sample has a high initial discharge capacity (130 mAh g⁻¹ at 0.1 C) and a reversible discharge capacity of 124.9 mAh g⁻¹ over 20 cycles. Moreover, the discharge capacity of the sample is still 91.5 mAh g⁻¹, even at a high rate of 2 C, which is better than that of the sample with common morphology. The improvement in electrochemical performance should be attributed to its improved lithium ion diffusion coefficient for the macroporous morphology, which was verfied by cyclic voltammetry and electrochemical impedance spectroscopy.     

Nano-composites SnO(VO<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript>) as anodes for lithium ion batteries

Nano-composites of SnO(V₂O₃) _x (x = 0, 0.25, and 0.5) and SnO(VO)_0.5 are prepared from SnO and V₂O₃/VO by high-energy ball milling (HEB) and are characterized by X-ray diffraction (XRD), scanning electron microscopy, and high-resolution transmission electron microscopy techniques. Interestingly, SnO and SnO(VO)_0.5 are unstable to HEB and disproportionate to Sn and SnO₂, whereas HEB of SnO(V₂O₃) _x gives rise to SnO₂.VO _x . Galvanostatic cycling of the phases is carried out at 60 mA g⁻¹ (0.12 C) in the voltage range 0.005–0.8 V vs. Li. The nano-SnO(V₂O₃)_0.5 showed a first-charge capacity of 435 (±5) mAh g⁻¹ which stabilized to 380 (±5) mAh g⁻¹ with no noticeable fading in the range of 10–60 cycles. Under similar cycling conditions, nano-SnO (x = 0), nano-SnO(V₂O₃)_0.25, and nano-SnO(VO)_0.5 showed initial reversible capacities between 630 and 390 (±5) mAh g⁻¹. Between 10 and 50 cycles, nano-SnO showed a capacity fade as high as 59%, whereas the above two VO _x -containing composites showed capacity fade ranging from 10% to 28%. In all the nano-composites, the average discharge potential is 0.2–0.3 V and average charge potential is 0.5–0.6 V vs. Li, and the coulombic efficiency is 96–98% after 10 cycles. The observed galvanostatic cycling, cyclic voltammetry, and ex situ XRD data are interpreted in terms of the alloying–de-alloying reaction of Sn in the nano-composite “Sn-VO _x -Li₂O” with VO _x acting as an electronically conducting matrix.     

Preparation and electrochemical performance of nano-structured Li<Subscript>2</Subscript>Mn<Subscript>4</Subscript>O<Subscript>9</Subscript> for supercapacitor

Nano-structured spinel Li₂Mn₄O₉ powder was prepared via a combustion method with hydrated lithium acetate (LiAc·2H₂O), manganese acetate (MnAc₂·4H₂O), and oxalic acid (C₂H₂O₄·2H₂O) as raw materials, followed by calcination of the precursor at 300 °C. The sample was characterized by X-ray diffraction, scanning electron microscope, and energy-dispersive X-ray spectroscopy techniques. Electrochemical performance of the nano-Li₂Mn₄O₉ material was studied using cyclic voltammetry, ac impedance, and galvanostatic charge/discharge methods in 2 mol L⁻¹ LiNO₃ aqueous electrolyte. The results indicated that the nano-Li₂Mn₄O₉ material exhibited excellent electrochemical performance in terms of specific capacity, cycle life, and charge/discharge stability, as evidenced by the charge/discharge results. For example, specific capacitance of the single Li₂Mn₄O₉ electrode reached 407 F g⁻¹ at the scan rates of 5 mV s⁻¹. The capacitor, which is composed of activated carbon negative electrode and Li₂Mn₄O₉ positive electrode, also exhibits an excellent cycling performance in potential range of 0–1.6 V and keeps over 98% of the maximum capacitance even after 4,000 cycles.     

Ammonia gas sensor based on a spinel semiconductor,Co<Subscript>0.8</Subscript>Ni<Subscript>0.2</Subscript>Fe<Subscript>2</Subscript>O<Subscript>4</Subscript> nanomaterial

Thick film of nanocrystalline Co_0.8Ni_0.2Fe₂O₄ was obtained by sol–gel citrate method for gas sensing application. The synthesized powder was characterized by X-ray diffraction (XRD) and transmission electron microscopy. The XRD pattern shows spinel type structure of Co_0.8Ni_0.2Fe₂O₄. XRD of Co_0.8Ni_0.2Fe₂O₄ revels formation of solid solution with average grain size of about 30 nm. From gas sensing properties it observed that nickel doping improves the sensor response and selectivity towards ammonia gas and very low response to LPG, CO, and H₂S at 280 °C. Furthermore, incorporation of Pd improves the sensor response and stability of ammonia gas and reduced the operating temperature upto 210 °C. The sensor is a promising candidate for practical detector of ammonia.     

Characterization of nanosized ZnAl<Subscript>2</Subscript>O<Subscript>4</Subscript> spinel synthesized by the sol–gel method

Single-phase zinc aluminate (ZnAl₂O₄) nanoparticles with the spinel structure was successfully obtained by the sol–gel method. The nanoparticles are crystalline with no impurities related to ZnO or Al₂O₃ residues. The microstructural environment of aluminum ions changes with heat treatment temperature, as observed by FT-IR and also by ²⁷Al solid-state magic angle spinning nuclear magnetic resonance (MAS NMR) spectra. The photoluminescence spectra show that the emission of pristine ZnAl₂O₄ may change depending on the calcining temperature due to the quantum size effect.     

Ferroelectric properties of La and V co-substituted SrBi<Subscript>4</Subscript>Ti<Subscript>4</Subscript>O<Subscript>15</Subscript> films prepared by sol-gel method

SrBi₄Ti₄O₁₅ (SBTi), SrBi_3.89La_0.1Ti_3.97V_0.03O₁₅ (SBLTV) thin films have been fabricated on Pt/Ti/SiO₂/Si by the sol–gel method. Well-saturated hysteresis loops with remnant polarization around 46.7 μC/cm² are obtained on Pt/SBLTV/Pt capacitors. The capacitor shows excellent fatigue resistance with no polarization reduction up to 10⁹ switching cycles even at low test frequency of 50 kHz. The improvement of ferroelectric and fatigue-endurance properties are attributed to the La³⁺ and V⁵⁺ co-substitution, which brings about the concentration decrease and the mobility weakening of the defects.     

Obtaining of Ni<Subscript>0.65</Subscript>Zn<Subscript>0.35</Subscript>Fe<Subscript>2</Subscript>O<Subscript>4</Subscript>/SiO<Subscript>2</Subscript> nanocomposites by thermal decomposition of complex compounds embedded in silica matrix

This article presents the results of our investigation on the obtaining of Ni_0.65Zn_0.35Fe₂O₄ ferrite nanoparticles embedded in a SiO₂ matrix using a modified sol–gel synthesis method, starting from tetraethylorthosilicate (TEOS), metal (Fe^III,Ni^II,Zn^II) nitrates and ethylene glycol (EG). This method consists in the formation of carboxylate type complexes, inside the silica matrix, used as forerunners for the ferrite/silica nanocomposites. We prepared gels with different compositions, in order to obtain, through a suitable thermal treatment, the nanocomposites (Ni_0.65Zn_0.35Fe₂O₄)_x–(SiO₂)_100–x (where x=10, 20, 30, 40, 50, 60 mass%). The synthesized gels were studied by differential thermal analysis (DTA), thermogravimetry (TG) and FTIR spectroscopy. The formation of Ni–Zn ferrite in the silica matrix and the behavior in an external magnetic field were studied by X-ray diffraction (XRD) and quasi-static magnetic measurements (50 Hz).     

The influence of Li sources on physical and electrochemical properties of LiNi<Subscript>0.5</Subscript>Mn<Subscript>1.5</Subscript>O<Subscript>4</Subscript> cathode materials for lithium-ion batteries

LiNi_0.5Mn_1.5O₄ cathode materials were successfully prepared by sol–gel method with two different Li sources. The effect of both lithium acetate and lithium hydroxide on physical and electrochemical performances of LiNi_0.5Mn_1.5O₄ was investigated by scanning electron microscopy, Fourier transform infrared, X-ray diffraction, and electrochemical method. The structure of both samples is confirmed as typical cubic spinel with Fd3m space group, whichever lithium salt is adopted. The grain size of LiNi_0.5Mn_1.5O₄ powder and its electrochemical behaviors are strongly affected by Li sources. For the samples prepared with lithium acetate, more spinel nucleation should form during the precalcination process, which was stimulated by the heat released from the combustion of extra organic acetate group. Therefore, the particle size of the obtained powder presents smaller average and wider distribution, which facilitates the initial discharge capacity and deteriorates the cycling performance. More seriously, there exists cation replacement of Li sites by transition metal elements, which causes channel block for Li ion transference and deteriorates the rate capability. The compound obtained with lithium hydroxide exhibits better electrochemical responses in terms of both cycling and rate properties due to higher crystallinity, moderate particle size, narrow size distribution and lower transition cation substitute content.