Raman spectroscopic and photoluminescence study of single-crystalline SnO2 nanowires

Single-crystalline SnO₂ nanowires with sizes of 4-14 nm in diameter and 100-500 nm in length were produced in a molten salt approach by using hydrothermal synthesized precursor. Structural characters of the nanowires were examined by X-ray diffraction and high-resolution electron transmission microscopy. Raman, photoluminescence and X-ray photoelectron spectra of the samples were examined under heat treatments. Three new Raman modes at 691, 514 and 358 cm⁻¹ were recorded and assigned. The former two are attributed to activation of original Raman-forbidden A_2uLO mode and the third is attributed to defects in small-sized nanowires. A strong photoluminescence is observed at about 600 nm, the temperature effects is examined and the origin of the PL process is discussed via X-ray photoelectron spectra.     

Structural and morphological transformations of Zn-Al layered double hydroxides through hydrothermal treatment

The Zn-Al layered double hydroxides (LDH) with Zn/Al molar ratio of 2 were prepared by coprecipitation, followed by hydrothermal treatment at various hydrothermal conditions. The phase transformation was observed, accompanied by drastical morphological changes. As the results indicated, in aqueous system the decomposition product was phase segregated into wurtzite ZnO and spinel ZnAl₂O₄ by dissolution of the precursor hydroxide followed by recoprecipitation of the oxide phases. As a single-source precursor, LDH facilitated the formation of ZnAl₂O₄ crystallites and their coating on ZnO nanowires via the inherent linkage through interactions of coordination as well as hydrogen bonding via medium of surface -OH on particles. The addition of ethanol with high vapor tension and low polarity was against the adsorptive attachment of ZnAl₂O₄ on ZnO but in favor of the crystallization and size decrease of the resulting oxides. Improved crystallization in LDH precursors was beneficial to intensify the interactions to overcome the breaking effect of ethanol, achieving better coating of ZnAl₂O₄ on ZnO. With the silane grafting of KH570, hydrothermal treatment promoted the formation of four phases by partial decomposition of layered structure of ZnAl-CO₃ and new emergence of smectite-like materials with basal spacing of 12.35 Å. As the aging time for LDH precursors gradually elongated, the whole products finally transformed to ultrafine nanorods with mean size of 50 nm in length which were segregated without any type of attachment.     

Nanocrystalline Sr2FeMoO6 prepared by citrate-gel method

Double perovskite Sr₂FeMoO₆ powders with small crystallite size have been synthesised with citrate-gel method. The starting solution pH was varied between 1.5 and 9.0 resulting in large differences in the phase composition and ordering of B^′/B^″ sites. The samples prepared at 975 °C had crystallite sizes under 40 nm whereas crystallite sizes of the samples prepared at 1050 °C were between 78 and 239 nm. The XRD patterns were refined with spacegroup I 4/m, which gave good results for both batches, although clearly better results were obtained with monoclinic P 2₁/n spacegroup for the 975 °C batch. The ordering and the saturation magnetization agreed well with each other after treatment at 1050 °C, but the samples prepared at 975 °C had a strongly reduced saturation magnetization from that given by the ordering.     

Growth of size-tunable periodic Ni silicide nanodot arrays on silicon substrates

The fabrications of size-tunable periodic arrays of nickel metal and silicide nanodots on (0 0 1)Si substrates using polystyrene (PS) nanosphere lithography (NSL) and heat treatments have been investigated. The growth of epitaxial NiSi₂ was found to be more favorable for the Ni metal nanodot arrays. The effect becomes more pronounced with a decrease in the size of the Ni nanodots. The sizes of the epitaxial NiSi₂ nanodots were tuned from 38 to 110 nm by varying the diameter of the PS spheres and heat treatment conditions. These epitaxial NiSi₂ nanodots formed on (0 0 1)Si were found to be heavily faceted and the faceted structures were more prone to form at higher temperatures. Based on TEM, HRTEM and SAED analysis, the faceted NiSi₂ nanodots were identified to be inverse pyramids in shape. Compared with the NiSi₂ nanodot arrays formed using single-layer PS sphere masks, the epitaxial NiSi₂ nanodot arrays formed from the double-layer PS sphere templates exhibit larger interparticle spacings and smaller particle sizes. Since the nanoparticle sizes, shapes and interparticle spacings can be adjusted by tuning the diameter of the PS spheres, stacking conditions, and heat treatment conditions, the PS NSL technique promises to be an effective patterning method for growth of other nanostructures.     

The effect of solution temperature on crystallite size and magnetic properties of Zn substituted Co ferrite nanoparticles

In this work zinc substituted cobalt ferrite nanoparticles (Co_0.5Zn_0.5Fe₂O₄) have been synthesized by the coprecipitation method, using stable ferric, zinc and cobalt salts with sodium hydroxide, at different solution temperatures, from room temperature to 363 K. The cobalt-zinc ferrite crystalline phase, the particle size and the morphology of the resulting nanoparticles were studied by X-ray diffraction and transmission electron microscopy. The average crystallite size of each sample was calculated from the broadening of the most intense peak (3 1 1), using Scherrer's formula and the results show crystallite sizes increased from 6 to 8 nm by increasing the solution temperature from room temperature to 363 K respectively. Room temperature VSM measurements show that the prepared nanoparticles have superparamagnetic behavior and did not saturate at maximum field of 800 kA/m. The variation of AC-susceptibility of the samples with respect to temperature was measured and it was found that the blocking temperature increased from 198 to 270 K by increasing the solution temperature from room temperature to 363 K respectively. FTIR spectra of the samples have been analyzed in the frequency range 400-4000 cm⁻¹, which also confirms the results of XRD.     

Investigations on structural and magnetic properties of cobalt ferrite/silica nanocomposites prepared by the coprecipitation method

Magnetic nanocomposites consisting of cobalt ferrite nanoparticles embedded in silica matrix were prepared by the coprecipitation method using metallic chlorides as precursors for ferrite. Subsequently composites were annealed at 100, 200 and 300 °C for 2 h. The samples were structurally characterized by X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR) and transmission electron microscopy (TEM). The magnetic properties were measured in the temperature range of 10-300 K using vibrating sample magnetometer (VSM). The effects of thermal treatment on structural and magnetic properties of nanocomposites were investigated. When the samples were annealed, CoFe₂O₄ nanocrystallites were observed in the SiO₂ matrix, whose size increases with increase in annealing temperature. The coercivity and saturation magnetization of nanocomposite (annealed at 300 °C for 2 h) are much higher than that of bulk cobalt ferrite. The realization of adjustable particle sizes and controllable magnetic properties makes the applicability of the CoFe₂O₄ nanocomposite more versatile.     

Effect of microstructural characteristics on the magnetic properties of sol-gel synthesized ZnMnO

In this paper we report the effect of microstructural characteristics on the magnetic properties of sol-gel synthesized Mn-doped ZnO. The microstructural characteristics of the samples (e.g., grain sizes and their distribution) have been varied by changing the sintering temperature (T_S) and sintering duration (T_H). Weak room temperature ferromagnetism (RTFM) has been observed in the samples sintered for ∼8 h at 500, 600, 700, 800 and 900 °C. The ferromagnetic fraction and the saturation magnetization, however, first increase as T_S increases from 500 to 600 °C and after that both start decreasing. On the other hand, the samples sintered for ∼12 h at the same temperatures show paramagnetic behavior at room temperature. Field emission scanning electron microscope (FESEM) results show enhancement in the grain sizes with the increase in both T_S and T_H. Energy dispersive X-ray (EDAX) results show increase in the oxygen content in the sample with increase in both T_S and T_H. X-ray diffractometer (XRD) measurements reveal that the basic crystal structure of all the samples corresponds to the wurtzite structure of pure ZnO together with some minor impurities. The correlation between the observed magnetic properties and the microstructural characteristics of the samples has been discussed in this paper.     

Synthesis process and the luminescence properties of rare earth doped NaLa(WO4)2 nanoparticles

Rare earth doped NaLa(WO₄)₂ nanoparticles have been prepared by a simply hydrothermal synthesis procedure. The X-ray diffraction (XRD) pattern shows that the Eu³⁺-doped NaLa(WO₄)₂ nanoparticles with an average size of 10-30 nm can be obtained via hydrothermal treatment for different time at 180 °C. The luminescence intensity of Eu³⁺-doped NaLa(WO₄)₂ nanoparticles depended on the size of the nanoparticles. The bright upconversion luminescence of the 2 mol% Er³⁺ and 20 mol% Yb³⁺ codoped NaLa(WO₄)₂ nanoparticles under 980 nm excitation could also be observed. The Yb³⁺-Er³⁺ codoped NaLa(WO₄)₂ nanoparticles prepared by the hydrothermal treatment at 180 °C and then heated at 600 °C shows a 20 times stronger upconversion luminescence than those prepared by hydrothermal treatment at 180 °C or by hydrothermal treatment at 180 °C and then heated at 400 °C.     

Synthesis and luminescence properties of Tb:NaGd(WO4)2 novel green phosphors

Tb³⁺:NaGd(WO₄)₂ (Tb:NGW) phosphors with different Tb³⁺ concentrations have been synthesized by a mild hydrothermal process directly without further sintering treatment. X-ray diffraction (XRD), scanning electron microscope (SEM), photoluminescence excitation and emission spectra and decay curve were used to characterize the Tb:NGW phosphors. XRD analysis confirmed the formation of NGW with scheelite structure. SEM study showed that the obtained Tb:NGW phosphors appeared to be nearly spherical and their sizes ranged from 1 to 1.5 μm. The excitation spectra of these systems showed an intense broad band with maximum at 270 nm related to the O→W ligand-to-metal charge-transfer state. Photoluminescence spectra indicated the phosphors emitted strong green light centered at 545 nm under UV light excitation. Analysis of the photoluminescence spectra with different Tb³⁺ concentrations revealed that the optimum dopant concentration for Tb³⁺ is about 15 at% of Tb³⁺ ions in Tb:NGW phosphors.     

Porosity depth profiling of spin-coated silica thin films produced by different precursors sols

The structural evolution of nanoporous silica thin films was studied by Doppler broadening spectroscopy (DBS), 2-3 gamma ratio of positronium (3γ-PAS) and Fourier transform infrared spectroscopy (FT-IR). Four series of silica films with thickness in the 300-600 nm range were deposited by spin coating on Si substrate changing the content of sacrificial porogen in the sol precursors. The effect on the porosity of different amount of porogen and of the thermal treatments in the 400-900 °C temperature range have been highlighted. The evolution of the porosity is discussed considering the removal of porogen and of the silanol Si-OH groups by thermal treatments as pointed out by FT-IR. Pores with size from less than 1 nm up to sizes larger than 2.0 nm have been detected. In samples with maximum porogen load oPs escaping was observed indicating onset of connected porosity. At temperatures higher than 700 °C a decrease of the porosity due to a progressive pore collapsing was evidenced. A strong correlation was found between the shift of the Si-O-Si transversal optical (TO₃) mode in the FT-IR spectra and the pore size in the porous silica films as revealed by DBS and 3γ-PAS.     

Physico-chemical properties and possible photocatalytic applications of titanate nanotubes synthesized via hydrothermal method

Titanate nanotubes (TNTs) were prepared from TiO₂ P25 via hydrothermal method. The reaction temperature was 130 or 140 °C and the reaction time was 24 or 48 h. The samples were characterized by transmission electron microscopy, X-ray diffraction, thermogravimetry and N₂ adsorption as well as Raman, FTIR-DRS and UV-vis/DR spectroscopy. The obtained samples exhibited similar properties, regardless of the preparation temperature and time. The most notable difference between properties of TNTs prepared under different conditions was observed in case of BET surface area, which was increasing from 386 to 478 m²/g along with increasing the reaction time and temperature. Based on TEM, XRD and TG measurements we have suggested that the structure of TNTs was H₂Ti₂O₄(OH)₂. The TEM and Raman spectroscopy measurements showed that the obtained products contained also low amount of anatase phase. The TNTs exhibited no photoactivity towards degradation of model azo dye Acid Red 18. However, TNTs were successfully applied for photocatalytic generation of CH₄ and H₂ in a solution of acetic acid. The amount of methane produced with application of TNTs synthesized at 140 °C was about 2.5 times higher than that generated with use of TiO₂ P25. To the best of our knowledge this is a first report on the photocatalytic generation of hydrocarbons using TNTs in the current state of the art.     

Biomolecule-assisted hydrothermal synthesis of Sb2S3 and Bi2S3 nanocrystals and their elevated-temperature oxidation behavior for conversion into α-Sb2O4 and Bi2O3

We have developed a novel biomolecule-assisted hydrothermal method to prepare Sb₂S₃ and Bi₂S₃ nanocrystals with various sizes and shapes, in which cysteine combined with other sulfur source can exert the synergistic effect on products. The samples were characterized XRPD, TEM, HRTEM, FESEM, and PL techniques. First, we prepared a series of Sb₂S₃ and Bi₂S₃ nanocrystals by simply adjusting the composition of sulfur sources under hydrothermal conditions. Then, we studied the elevated-temperature oxidation behavior of these sulfides in air, which can lead to the formation of α-Sb₂O₄ and Bi₂O₃ samples at 600 °C for 3 h. The optical properties of the α-Sb₂O₄ and Bi₂O₃ samples were also discussed.     

Chemical synthesis of BaCO3 with a hexagonal pencil-like morphology

Uniform hexagonal pencil-like BaCO₃ whiskers have been successfully synthesized by the chemical reaction of barium chloride and urea via a facile hydrothermal route. Most whiskers have well-defined crystallographic facets and a regular prismatic hexagon with the length up to 50 μm and diameter around 5 μm. The straight pencil-like BaCO₃ whisker is grown along the c-axial direction, the six faces of whiskers are consisted of both {0 1 0} and {1 1 0} planes. The present hydrothermal synthetic system tends to provide an appropriate chemical microenvironment for the formation of hexagonal pencil-like BaCO₃ whiskers, due to the fact that the homogeneous decomposition of urea plays an essential role in the whole process.     

Comparison of different NaGdF4:Eu synthesis routes and their influence on its structural and luminescent properties

Eu³⁺:NaGdF₄ samples were obtained via co-precipitation in aqueous solution (CP), reversed micelle (RM) method, reaction between solid GdF₃ and NaF solution (SR) as well as a solid-state reaction at high temperatures (SS). The synthesised materials were characterised using X-ray powder diffractometry, TEM microscopy, infrared spectroscopy and TGA analysis. For discussion of optical properties excitation and emission spectra were recorded and emission decay times were measured. The CP and RM methods allow to obtain powders with crystallite size of ∼10 nm, which may be smoothly increased to about 1 μm during post-fabrication heat treatment. Differences in structural and especially in optical properties of phosphors prepared by different techniques are emphasised and applicability of wet-chemistry routes for synthesis of fluoride powders is argued.     

Preparation and characterization of Cobalt Sulfophthalocyanine/TiO2/fly-ash cenospheres photocatalyst and study on degradation activity under visible light

Cobalt Sulfophthalocyanine (CoSPc) sensitized TiO₂ sol samples were prepared through a Sol-Gel method using Cobalt Sulfophthalocyanine as a sensitizer. Loading and modified floating photocatalyst was prepared by hydrothermal method using fly-ash cenospheres as a carrier. The properties of the samples were characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD), Fourier transform infrared (FT-IR) and UV-vis diffuse reflectance spectrum (DRS). Photocatalytic activity was studied by degrading wastewater of methylene blue under visible light. The results indicate that the fly-ash cenospheres are covered by modified TiO₂ film which composed of the anatase, brookite and rutile misch crystal phase. CoSPc/TiO₂/fly-ash cenospheres samples have good catalytic activity under visible light, and have strong absorbency during 600-700 nm. The sensitization of CoSPc can enhance visible light catalytic activity of TiO₂/fly-ash cenospheres. The degradation rate of methylene blue reaches 73.36% in 180 min under the visible light illumination. But too much CoSPc can decrease its catalytic activity.     

A novel strategy to synthesize cobalt hydroxide and Co3O4 nanowires

Cobalt hydroxide ultra fine nanowires were prepared by a facile hydrothermal route using hydrogen peroxide. This method provides a simple, low cost, and large-scale route to produce β-cobalt hydroxide nanowires with an average diameter of 5 nm and a length of ca. 10 μm, which show a predominant well-crystalline hexagonal brucite-like phase. Their thermal decomposition produced highly uniform nanowires of cobalt oxide (Co₃O₄) under temperature 500 °C in the presence of oxygen gas. The produced cobalt oxide was characterized by X-ray diffraction, transmission electronic microscopy, and selected-area electron diffraction. The results indicated that cobalt oxide nanowires with an average diameter of 10 nm and a length of ca. 600 nm have been formed, which show a predominant well-crystalline cubic face-centered like phase.     

Physico-chemical properties of titania nanotubes synthesized via hydrothermal and annealing treatment

Titania nanotubes are synthesized via hydrothermal treatment of TiO₂ powders in NaOH solution at 110 °C for 90 h, followed by annealing at 400 °C. The morphology of nanotubes is characterized by field-emission scanning electron microscopy (FESEM) and transmission electron microscopy (TEM). Microscopic observations on the transformation process indicate that the nanotubes retain their shapes after the annealing process. The crystalline structure and composition are examined by X-ray diffraction (XRD) and energy-dispersive X-ray spectroscopy (EDX). The results confirm the absence of impurity peaks and the crystal structure change from nanotubes to anatase phase after annealing treatment. The average specific surface area of the particles is probed using gas adsorption-desorption measurements. The prepared tubular samples exhibit greater specific surface areas and higher pore volumes than the precursor. Moreover, it is apparent that the hydrothermal treatment modifies the optical properties of the titania samples and red-shifts the UV absorption to a band gap energy of 3.04 eV after annealing treatment.     

Surface study of fine MgFe2O4 ferrite powder prepared by chemical methods

To study surface behaviors, MgFe₂O₄ ferrite materials having different grain sizes were synthesized by two different chemical methods, i.e., a polymerization method and a reverse coprecipitation method. The single phase of the cubic MgFe₂O₄ was confirmed by the X-ray diffraction method for both the precursors decomposed at 600-1000 °C except for a very small peak of Fe₂O₃ was detected for the samples calcined at 600 and 700 °C by the polymerization method. The crystal size and particle size increased with an increase in the sintering temperature using both methods. The conductance of the MgFe₂O₄ decreased when the atmosphere was changed from ambient air to air containing 10.0 ppm NO₂. The conductance change, C = G(air)/G(10 ppm NO₂), was reduced with an increase in the operating temperature. For the polymerization method, the maximum C-value was ca. 40 at 300 °C for the samples sintered at 900 °C. However, the samples sintered at 1000 °C showed a low conductance change in the 10 ppm NO₂ gas, because the ratio of the O₂ gas adsorption sites on the particle surface is smaller than those of the samples having a high C-value. The low Mg content on the surface affects the low ratio of the gas adsorption sites. For the reverse coprecipitation method, the particle size was smaller than that of the polymerization method. Although a stable conductance was obtained for the sample sintered at 900 and 1000 °C, its conductance change was less than that of the polymerization method.     

An investigation on the behavior of fine-grained magnetite particles as a function of size and surface modification

By using a KNO₃-aging ferrous hydroxide gel method, Fe₃O₄ particles with sizes ranging from 35 to 1500 nm were synthesized. The particles were covered with a silica coating to form Fe₃O₄-SiO₂ core-shell structures by using the improved conventional Stöber polycondensation method. The thickness of the SiO₂ covering on magnetite particles surface varies from 10 to 20 nm. The morphology, size and composition of the particles were determined by transmission electron microscopy (TEM) and X-ray diffraction (XRD). The particles with and without coating with SiO₂ were pressed into slices with an oil press at 10 MPa. Subsequently, the coercive forces H_C of the particles were measured by VSM at room temperature, and the critical size for a single domain was estimated. The shape of the particles is basically spherical when the size is smaller than 800 nm, while it is hexagonal for larger particles. The H_C of Fe₃O₄-SiO₂ core-shell structure was larger than that of the uncoated Fe₃O₄ particles by 20%, which was explained to be due to the reduction of inter-particle magnetostatic interaction, supported by an agreement with the packing factor. The dependence of H_C on magnetic particle size could be explained and fitted by the Heewell-Knozam stacking density equation and object-oriented micromagnetic computing framework (OOMMF) micromagnetic software. the results agree well with the experimental data.