In-situ XAS study on the Cu and Ce local structural changes in a CuO-CeO2/Al2O3 catalyst under propane reduction and re-oxidation

The redox behaviour of a CuO-CeO₂/Al₂O₃ catalyst is studied under propane reduction and re-oxidation. The evolution of the local Cu and Ce structure is studied with in-situ transmission X-ray absorption spectroscopy (XAS) at the Cu K and Ce L₃ absorption edges.CuO and CeO₂ structures are present in the catalyst as such. No structural effect on the local Cu structure is observed upon heating in He up to 873 K or after pre-oxidation at 423 K.Exposure to propane at reaction temperature (600-763 K) fully reduces the Cu²⁺ cations towards metallic Cu⁰. Quick EXAFS spectra taken during reduction show a small amount of intermediate Cu¹⁺ species. Parallel to the CuO reduction, CeO₂ is also reduced in the same temperature range. About 25% of the Ce⁴⁺ reduces rapidly to Ce³⁺ in the 610-640 K temperature interval, while beyond 640 K a further slower reduction of Ce⁴⁺ to Ce³⁺ occurs. At 763 K, Ce reduction is still incomplete with 32% of Ce³⁺.Re-oxidation of Cu and Ce is fast and brings back the original oxides.The propane reduction of the CuO-CeO₂/Al₂O₃ catalyst involves both CuO and CeO₂ reduction at similar temperatures, which is ascribed to an interaction between the two compounds.     

Electronic structure of BaTiO3 using resonant X-ray emission spectroscopy at the Ba-L3 and Ti-K absorption edges

We have studied the electronic properties of the ferroelectric barium titanate BaTiO₃ using two complementary bulk-sensitive spectroscopic probes, resonant X-ray emission spectroscopy (RXES) and X-ray absorption spectroscopy in the partial fluorescence mode (PFY-XAS) at the Ba-L₃ and Ti-K absorption edges. Contrary to a previous study, we found no fine structure in the pre-edge area of the PFY-XAS spectrum at the Ba-L₃ edge, and no temperature-induced spectral change was observed between room temperature and 150 °C. This result is not supportive of the possible presence of the displacement around Ba²⁺ at the Curie temperature. RXES spectra were measured at the Ti-K edge for BaTiO₃, along with SrTiO₃ and La-doped metallic SrTiO₃. The photon energy of the emission peak is found to be nearly constant throughout the absorption edge for all three compounds. We deduce the Ti 3d states to have a delocalized character, in contrast with the Ba 5d states, a property which is consistent with the proposed scenario of the formation of electric dipoles in BaTiO₃.     

The photoluminescent properties of Eu in MgO-Ga2O3-SiO2 nanocrystalline glass-ceramic

The MgO-Ga₂O₃-SiO₂ glass-ceramic (GC) containing MgGa₂O₄ nanocrystals and glasses doped with Eu³⁺ ions were prepared by the sol-gel method. The down-conversion and up-conversion luminescence (UCL) properties were studied. The results indicated that the relative intensity of f-f transitions of Eu³⁺ decreased in contrast with that of charge transfer (CT) absorption with the increase in heating temperature. Using a Xe lamp and 800 nm femtosecond (fs) laser excitation, strong red luminescence of Eu³⁺ in MgO-Ga₂O₃-SiO₂ glasses and GC was observed.     

XAFS at Eu-L3 edge and UV-VUV excited luminescence of europium doped strontium borophosphate prepared in air

The local structure and the valences of europium in SrBPO₅:Eu prepared in air were checked by means of XAFS at Eu-L₃ edge. From the EXAFS results, it was discovered that the doped europium atoms were nine-coordinated by oxygen atoms and the distances of bond Eu-O were 2.42 Å in the host. From the XANES data, it was found that the divalent and trivalent europium coexisted in the matrix. The emission spectra excited by VUV or UV exhibited a prominent broad band due to the 4f⁶5d-4f⁷ transition of Eu²⁺ ions, which indicated that the trivalent europium ions were reduced in air in the matrix at high temperature by the defects [V_Sr]″ formed by aliovalent substitution between Sr²⁺ and Eu³⁺ ions. The VUV excitation spectra in 100-200 nm range showed that the matrix had absorption bands with the maxima at about 130 and 150 nm, respectively.     

Effect of hydroxyl groups on Er doped Bi2O3-B2O3-SiO2 glasses

A series of Er³⁺-doped Bi₂O₃-B₂O₃-SiO₂-Na₂O glasses with different hydroxyl groups were prepared and the interaction between the Er³⁺ ions and OH groups was investigated. Infrared spectra were measured in order to calculate the exact content of OH groups in samples. The observed increase of the fluorescence lifetime with the oxygen bubbling time has been related to the reduction in the OH content concentration evidenced by infrared (IR) absorption spectra, which confirmed that the OH groups were dominant quenching centers of excited Er³⁺ and a cause of concentration quenching of 1.5 μm band emission. Various nonradiative decay rates from ⁴I_13/2 of Er³⁺ with the change of OH content were determined from the fluorescence lifetimes and radiative decay rates, which were calculated on the basis of Judd-Ofelt theory.     

Photocatalytic activity of Nb2O5/SrNb2O6 heterojunction on the degradation of methyl orange

The pure SrNb₂O₆ powders were prepared at 1400 °C by a conventional solid-state method and characterized by X-ray powder diffraction and UV-vis diffuse reflection spectrum. The powders of Nb₂O₅ and SrNb₂O₆ were ball-milled together and annealed to form the Nb₂O₅/SrNb₂O₆ composite. Photocatalytic activities of the composites were investigated on the degradation of methyl orange. The results show that the proportion of Nb₂O₅ to SrNb₂O₆ and the annealing temperature greatly influence the photocatalytic activities of the composites. The best photocatalytic activity occurs when the weight proportion of Nb₂O₅ to SrNb₂O₆ is 30% and the annealing temperature is 600 °C. The tremendously enhanced photocatalytic activity of the Nb₂O₅/SrNb₂O₆ composite compared to Nb₂O₅ or SrNb₂O₆ is ascribed to the heterojunction effect taking place at the interface between particles of Nb₂O₅ and SrNb₂O₆. The powders also show a higher photocatalytic activity than commercial anatase TiO₂.     

Optical absorption spectrum of Cu2O-CaO-P2O5 glasses

Homogeneous CaO-P₂O₅ and Cu₂O-CaO-P₂O₅ glasses were prepared using a melt-quenched method under controlled conditions. The binary glasses were found to be colourless and transparent while the ternary glasses changed from light green to dark green as the Cu₂O content increased. From the absorption edge studies, the values of the optical band gap, E_opt and Urbach energy, ΔE were evaluated. The position of the absorption edge and hence the optical band gap were found to depend on the glass composition. Analysis of the optical band gap shows that for the binary glasses, the value increases as the content of CaO decreases, while for the ternary glasses, the value of the optical band gap increases as the content of the Cu₂O decreases. The density of the glasses was also measured and was found to increase with the increase in CaO and Cu₂O contents.     

EXAFS study of size dependence of atomic structure in palladium nanoparticles

Dependence of atomic structure of Palladium nanoparticles on supports Al₂O₃ and SiO₂ upon their size, changed from 1.3 to 10.5 nm, was studied by Pd K-edge EXAFS. To determine the structure of the interior (core) and the near surface regions of nanoparticle, the fitting technique of the Fourier-transforms F(R) of spectra was used, which enabled to overcome instabilities of the obtained structural parameters values. The processing of experimental data was performed using results of the study of features formation in │F(R)│ of Pd K-EXAFS in Pd foil. By this approach it was revealed that the local structure of Pd atoms in the core is similar to fcc structure of bulk Pd, irrespective of size. The percentage of Pd atoms, which can be attributed to the core, upon the particles size was determined and the obtained dependence was described by the “cluster size equation”. In the near surface region of nanoparticles, nearest-neighbors Pd–Pd distances show a large Debye–Waller parameters and the mean bond length slightly contracted for nanoparticles of sizes less than ~2 nm. The effect of small structural distortions in the vicinity of absorbing Pd atom in the near surface region was studied using the cluster model of nanoparticle.     

Preparation of TiO2 hollow spheres for DSSC photoanodes

High crystallinity mesoporous TiO₂ hollow spheres (MHS-TiO₂) were prepared using the mesoporous carbon hollow sphere template. The MHS-TiO₂ contains mainly nanostructured anatase. The mesopore of the MHS-TiO₂ has a pore opening in the range of 400–600 nm. The refined extended X-ray absorption fine structure spectra indicate that the MHS-TiO₂ possesses less the 1st-shell Ti–O coordination numbers than the nano-TiO₂. More surface active species (A₂ ((Ti=O)O₄)) on the MHS-TiO₂ are also observed by the component fitted X-ray absorption near edge structure spectroscopy. The MHS-TiO₂ photoanode has a better DSSC conversion efficiency than the nano-TiO₂ one by at least 40%. Note that the N3 dye molecules are accessible to the mesopores of the MHS-TiO₂, and the loading time for N3 can be reduced by at least 70% if compared with those of the nano-TiO₂.     

Redox state of plutonium in irradiated mixed oxide fuels

Nowadays, MOX fuels are used in about 20 nuclear power plants around the world. After irradiation, plutonium co-exists with uranium oxide. Due to the redox sensitive nature of UO₂ other plutonium oxides than PuO₂ potentially present in the fuel may interact with the matrix. The aim of this study is to determine which plutonium species are present in heterogeneous and homogeneous MOX. The results provided by X-ray Absorption Near Edge Spectroscopy (XANES) for non-irradiated as well as irradiated (center and periphery) homogeneous MOX fuel were published earlier and are completed by Extended X-ray Fine Structure (EXAFS) analysis in this work. The EXAFS signals have been extracted using the Athena code and the analyses were carried using Excure98 as performed earlier for an analogous element. EXAFS shows that plutonium redox state remains tetravalent in the solid solution and that the minor fraction of trivalent Pu must be below 10%. Independently, the study of homogeneous MOX was also approached by thermodynamics of solid solution of (U,Pu)O₂. Such solid solutions were modeled using the Gibbs Energy Minimisation (GEM)-Selektor code (developed at LES, NES, PSI) supported by the literature data on such solid solutions. A comparative study was performed showing which plutonium oxides in their respective mole fractions are more likely to occur in (U,Pu)O₂. In the modeling, these oxides were set as ideal and non-ideal solid solutions, as well as separate pure phases. Pu exists mainly as PuO₂ in the case of separate phases, but can exist under its reduced forms, PuO_1.61 and PuO_1.5 in minor fraction i.e. ~15% in ideal solid solution (unlikely) and ~10% in non-ideal solid solution (likely) and at temperature around 1300 K. This combined thermodynamic and EXAFS studies confirm independently the results obtained so far by Pu XANES for the same MOX samples.     

Immiscibility in the NiFe2O4-NiCr2O4 spinel binary

The solid solution behavior of the Ni(Fe_1−nCr_n)₂O₄ spinel binary is investigated in the temperature range 400-1200 °C. Non-ideal solution behavior, as exhibited by non-linear changes in lattice parameter with changes in n, is observed in a series of single-phase solids air-cooled from 1200 °C. Air-annealing for 1 year at 600 °C resulted in partial phase separation in a spinel binary having n=0.5. Spinel crystals grown from NiO, Fe₂O₃ and Cr₂O₃ reactants, mixed to give NiCrFeO₄, by Ostwald ripening in a molten salt solvent, exhibited single-phase stability down to about 750 °C (the estimated consolute solution temperature, T_cs). A solvus exists below T_cs. The solvus becomes increasingly asymmetric at lower temperatures and extrapolates to n values of 0.2 and 0.7 at 300 °C. The extrapolated solvus is shown to be consistent with that predicted using a primitive regular solution model in which free energies of mixing are determined entirely from changes in configurational entropy at room temperature.     

Microstructural, dielectric and spectroscopic properties of Li2O-Nb2O5-ZrO2-SiO2 glass system crystallized with V2O5

Li₂O-Nb₂O₅-ZrO₂-SiO₂ glasses mixed with different concentrations of V₂O₅ were crystallized. The samples were characterized by XRD, SEM and DTA techniques. The SEM pictures indicated that the samples contain well defined and randomly distributed crystal grains. The X-ray diffraction studies have revealed the presence of several crystalline phases in these samples. Optical absorption, ESR and photoluminescence spectral studies on these samples have indicated that a considerable proportion of vanadium ions do exist in V⁴⁺ state in addition to V⁵⁺ state and the redox ratio seems to be increasing with increase in the concentration of crystallizing agent V₂O₅. The infrared spectral studies have pointed out the existence of conventional SiO₄, ZrO₄, NbO₆, VO structural units in the glass ceramic network. The study of dielectric properties suggested a decrease in the insulating character of the glass ceramics with increase in the crystallizing agent. A.C. conductivity in the high temperature region seems to be connected mainly with the polarons involved in the process of transfer from V⁴⁺↔V⁵⁺ ions.     

Studies on the influence of lithium incorporation in the photoluminescence of Y2O3:Eu thin films

Nanostructured europium-doped yttrium oxide thin films with lithium as a co-dopant were prepared using pulsed laser ablation technique. X-ray diffraction studies of the films indicated amorphous nature of the as deposited films and a transformation to crystalline phase with increase of annealing temperature. In this transformation, lithium co-doped films showed early crystallization. Lithium substitution resulted not only in enhancement of photoluminescence at 612 nm, resulting from ⁵D₀-⁷F₂ transition within europium, but also found to reduce the required processing temperature for intense photoemission. The deviation observed in the value of lattice constant of films annealed at different temperatures is found to be sensitive to annealing temperature. In the light of this, the dependence of photoluminescence intensity on the magnitude of lattice imperfection is also discussed. The morphology and transmittance of the films are also found to be sensitive to annealing process and lithium doping.     

Comparative investigation on spectroscopic properties of Er between Ce-doped and B2O3-added bismuth glasses

The comparative investigation on the spectroscopic properties of Er³⁺ in low phonon energy Bi₂O₃-GeO₂-Ga₂O₃-Na₂O glasses codoped with Ce³⁺ ion and added with B₂O₃ component, respectively, is presented. With increasing Ce₂O₃ content from 0 to 0.8 mol% or B₂O₃ content from 0 to 15 mol%, the lifetime of Er³⁺:⁴I_11/2 level decreases dramatically from 607 to 283 μs or to 197 μs, and the upconversion fluorescence is quenched in both glass samples. The nonradiative energy transfer from Er³⁺:⁴I_11/2→Ce³⁺:²F_5/2 or the enhanced multiphonon relaxation process together with the energy transfer between Er³⁺ and OH⁻ groups are, respectively, responsible for the results. Meanwhile, the lifetime of ⁴I_13/2 level remains almost unchanged in Er³⁺/Ce³⁺-codoped glasses whereas it decreases rapidly in B₂O₃-added cases. As a result, Er³⁺/Ce³⁺ codoping improves the 1.5 μm fluorescence emission intensity, however, B₂O₃ addition has a negative effect on it. The research results indicate that the Er³⁺/Ce³⁺-codoped bismuth glasses will be preferable for obtaining efficient 980 nm pumped EDFA.     

Thermoluminescence studies of LiBa2B5O10:RE (RE=Dy, Tb and Tm)

LiBa₂B₅O₁₀:RE³⁺ (RE=Dy, Tb and Tm) was synthesized by the method of high-temperature solid-state reaction and the thermoluminescence (TL) properties of the samples under the irradiation of the γ-ray were studied. The result showed that Dy³⁺ ion was the most efficient activator. When the concentration of Dy³⁺ was 2 mol%, LiBa₂B₅O₁₀:Dy³⁺ exhibited a maximum TL output. The kinetic parameter of LiBa₂B₅O₁₀:0.02Dy was estimated by the peak shape method, for which the average activation energy was 0.757 eV and the frequency factor was 1.50×10⁷ s⁻¹. By the three-dimensional (3D) TL spectrum, the TL of the sample was contributed to the characteristic f-f transition of Dy³⁺. The dose-response of LiBa₂B₅O₁₀:0.02Dy to γ-ray was linear in the range from 1 to 1000 mGy. In addition, the decay of the TL intensity of LiBa₂B₅O₁₀:0.02Dy was also investigated.     

Effects of Na2CO3 flux addition on the structure and photoluminescence properties for Eu-doped YVO4 phosphor

The luminescence properties of (Y_0.9Eu_0.1)VO₄ phosphor with Na₂CO₃ flux prepared using the solid-state reaction were investigated. The XRD patterns show that all of the peaks are attributed to the YVO₄ phase. The best crystallinity was obtained with 2 wt% Na₂CO₃ flux addition. The surface morphology of (Y_0.9Eu_0.1)VO₄ phosphor changed from fluffy to a bar shape structure after Na₂CO₃ flux addition due to the tetragonal crystal system of YVO₄. The calcined powders emit bright red luminescence centered at 618 nm due to the ⁵D₀→⁷F₂ electric dipole transition under an excitation wavelength of 318 nm; its intensity was increased about 15% with 2 wt% Na₂CO₃ flux addition. Red shift behavior was observed for the charge transfer state (CTS) absorption, which was due to the grain size of (Y_0.9Eu_0.1)VO₄ phosphor increasing with increasing flux content. For 2 wt% Na₂CO₃ flux addition, the red emission of the (Y_0.9Eu_0.1)VO₄ phosphor had CIE chromaticity coordinates of (0.66, 0.34), which are very close to the NTSC system standard red chromaticity coordinates of (0.67, 0.33).     

Immiscibility in the Fe3O4-FeCr2O4 spinel binary

A recent thermodynamic model of mixing in spinel binaries, based on changes in cation disordering (x) between tetrahedral and octahedral sites [Am. Mineral. 68 (1983) 18, 69 (1984) 733], is investigated for applicability to the Fe₃O₄-FeCr₂O₄ system under conditions where incomplete mixing occurs. Poor agreement with measured consolute solution temperature and solvus [N. Jb. Miner. Abh. 111 (1969) 184] is attributed to neglect of: (1) ordering of magnetic moments of cations in the tetrahedral sublattice antiparallel to the moments of those in the octahedral sublattice and (2) pair-wise electron hopping between octahedral site Fe³⁺ and Fe²⁺ ions. Disordering free energies (ΔG_D), from which free energies of mixing are calculated, are modeled by

     

Linear and nonlinear optical susceptibilities of orthorhombic rare earth molybdates RE2(MoO4)3

The dielectric responses (i.e. the refractive indices and the second order nonlinear susceptibilities) of all orthorhombic rare earth molybdates have been studied on the basis of the relationship between dielectric responses and the average atomic number of constituent atoms of crystals. Both the linear and second order nonlinear optical responses at 1.064 μm decrease with increasing atomic number from La to Lu.     

Growth and optical properties of Eu/Li-co-doped SrB4O7 single crystals

This paper reports the growth and optical properties of Eu²⁺/Li⁺-co-doped SrB₄O₇ single crystals. High-quality Eu,Li:SrB₄O₇ crystals without macro-defects or cracks were grown using the top-seeded solution growth (TSSG) method. The absorption and luminescent properties were measured and different spectra were observed in the as-grown crystals. As the doping amount of lithium increases, the absorption peak at 300 nm becomes stronger and the emission peak shifts to a longer wavelength. This phenomenon could be attributed to the doping lithium ions, which might affect the electric field distribution in the lattice structure.     

Local order and structural transitions in the molecule-based layer ferrimagnet (n-C4H9)4N FeFe(C2O4)3

Local structural order and temperature-dependent structural variation have been studied in the molecular-based layer ferrimagnet (n-C₄H₉)₄N Fe^IIFe^III(C₂O₄)₃ by EXAFS and high resolution X-ray powder diffraction. The EXAFS spectra measured at the Fe K-edge are successfully modelled by successive O, C, O and metal shells, showing that even when there is extensive structural disorder due to stacking faults, the local structural order in this class of ferrimagnets is fully retained. In this salt, which shows remarkable negative magnetisation at low temperature (Néel class Q), the EXAFS Debye-Waller factor has a discontinuity at 40 K, corresponding to one found in the magnetisation. At the same temperature there is also a change in the expansion of the lattice as evidenced by the high resolution X-ray powder diffraction.