Structural stability,electronic structure and mechanical properties of 4d transition metal nitrides TMN (TM=Ru,Rh, Pd)

Ab initio calculations are performed to investigate the structural stability, electronic, structural and mechanical properties of 4d transition metal nitrides TMN (TM=Ru, Rh, Pd) for five different crystal structures, namely NaCl, CsCl, zinc blende, NiAs and wurtzite. Among the considered structures, zinc blende structure is found to be the most stable one among all three nitrides at normal pressure. A structural phase transition from ZB to NiAs phase is predicted at a pressure of 104 GPa, 50.5 GPa and 56 GPa for RuN, RhN and PdN respectively. The electronic structure reveals that these nitrides are metallic. The calculated elastic constants indicate that these nitrides are mechanically stable at ambient condition.     

A new high-pressure phase of ZnSe with B9-type structure

High-pressure and high-temperature behavior of ZnSe was investigated by energy dispersive X-ray diffraction method up to 14 GPa and 800°C. A new high-pressure phase with B9 (HgS)-type structure is found near the B3-B1 phase boundary at room temperature, as predicted by an ab-initio calculation. The property and observed pressure region of the B9-type phase are in good agreement with the ab-initio calculation. At high-temperature condition above 300°C, only the direct transitions are observed between the B3 and B1 phases. The B3-B1 phase boundary is also determined to be P (GPa)=12.21−0.0039T (°C) for the temperature range between 300 and 800°C.     

In situ observations of temperature- and pressure-induced phase transitions in TiH2: Angle-dispersive and synchrotron energy-dispersive X-ray diffraction studies

We investigated the behavior of the structure of titanium hydride (TiH₂), an important compound in hydrogen storage research, at elevated temperatures (0-120 °C) and high pressures (1 bar-34 GPa). Temperature-induced changes of TiH₂ as indicated in the alteration of the ambient X-ray demonstrated a cubic to tetragonal phase transition occurring at about 17 °C. The main focus of this study was to identify any pressure-induced structural transformations, including possible phase transitions, in TiH₂. Synchrotron X-ray diffraction studies were carried out in situ (diamond anvil cell) in a compression sequence up to 34 GPa and in subsequent decompression to ambient pressure. The pressure evolution of the diffraction patterns revealed a cubic (Fm-3m) to tetragonal (I4/mmm) phase transition at 2.2 GPa. The high-pressure phase persisted up to 34 GPa. After decompression to ambient conditions the observed phase transition was completely reversible. A Birch-Murnaghan fit of the unit cell volume as a function of pressure yielded a zero-pressure bulk modulus K₀=146(14) GPa, and its pressure derivative K′₀=6(1) for the high-pressure tetragonal phase of TiH₂.     

A composite high-pressure cell with sintered diamond insets for study of thermoelectric and thermomagnetic properties in a range up to 30 GPa: Application to Pr and PbTe

A composite high-pressure cell with the sintered diamond insets is reported to be an effective tool for investigation of transport properties of solids under pressure as high as ∼30 GPa. The temperature distribution inside the cell was calculated. Using this cell, the pressure-driven phase transitions in praseodymium (Pr) have been studied by the thermopower technique (Seebeck effect). The results have shown that a scenario of the phase transitions in Pr (existence of the monoclinic C2/m phase) crucially depends on defects and distortions in a crystal lattice. So, the monoclinic phase was noticeable only for the first pressurization cycle. A technique of measurement of the longitudinal and the transverse thermomagnetic Nernst-Ettingshausen (N-E) effects (magnetothermopower) under high P is explained. With an example of lead telluride (PbTe), it is demonstrated that magnetic field can significantly improve the thermoelectric efficiency under pressure. The merits of the cell developed are discussed concerning basic research and technologies.     

X-ray diffraction and infrared spectroscopy of monazite-structured CaSO4 at high pressures: Implications for shocked anhydrite

X-ray diffraction and infrared spectroscopy of CaSO₄ are conducted to pressures of 28 and 25 GPa, respectively. A reversible phase transition to the monoclinic monazite-structure occurs gradually between 2 and ∼5 GPa with a highly pressure-dependent volume change of ∼6-8%. A second-order fit of the X-ray data to the Birch-Murnaghan equation of state yields a bulk modulus (K) of 151.2 (±21.4) GPa for the high-pressure monoclinic phase. In the high-pressure infrared spectrum, the infrared-active asymmetric stretching and bending vibrations of the sulfate tetrahedra split at the phase transition, in accord with the results of factor group analysis. Additionally, the tetrahedral symmetric stretching vibration, which is weak in the anhydrite phase, becomes strongly resolved at the transition to the monazite structure. The infrared results indicate that the sulfate tetrahedra are more distorted in the monazite-structured phase than in anhydrite. Kinetic calculations indicate that the anhydrite to monazite transformation may generate the phase transition observed near 30 GPa under shock loading in CaSO₄. Our results indicate that the anhydrite- and monazite-structured phases may be the only phases that occur under shock loading of CaSO₄ to pressures in excess of 100 GPa.     

Full potential calculation of structural, elastic properties and high-pressure phase of binary noble metal carbide: ruthenium carbide

We present in this paper the results of an ab initio theoretical study within the local density approximation (LDA) to determine in rock-salt (B1), cesium chloride (B2), zinc-blende (B3), and tungsten carbide (WC) type structures, the structural, elastic constants, hardness properties and high-pressure phase of the noble metal carbide of ruthenium carbide (RuC).The ground state properties such as the equilibrium lattice constant, elastic constant, the bulk modulus, its pressure derivative, and the hardness in the four phases are determined and compared with available theoretical data. Only for the three phases B1, B3, and WC, is the RuC mechanically stable, while in the B2 phase it is unstable, but in B3 RuC is the most energetically favourable phase with the bulk modulus 263 GPa, and at sufficiently high pressure (P_t=19.2 GPa) the tungsten carbide (WC) structure would be favoured, where ReC-WC is meta-stable.The highest bulk modulus values in the B3, B2, and WC structures and the hardnesses of H(B3)=36.94 GPa, H(B1)=25.21 GPa, and H(WC)=25.30 GPa indicate that the RuC compound is a superhard material in B3, and is not superhard in B1 and WC structures compared with the H(diamond)=96 GPa.     

Ionic to electronic dominant conductivity in Al2(WO4)3 at high pressure and high temperature

Electrical conduction and crystal structure of Al₂(WO₄)₃ at 400 °C have been studied as a function of pressure up to 5.5 GPa using impedance methods and synchrotron radiation X-ray diffraction, respectively. AC impedance spectroscopy and DC polarization measurements reveal an ionic to electronic dominant transition in electrical conductivity at a pressure as low as 0.9 GPa. Conductivity increases with pressure and reaches a maximum at 4.0 GPa, where the conductivity value is 5 orders of magnitude greater than the 1 atm value. Upon decompression, the conductivity retains the maximum value until the sample is cooled at 0.5 GPa. The high pressure-temperature X-ray diffraction results show that the lattice parameters decrease as pressure increases and the crystal structure undergoes an orthorhombic to tetragonal-like transformation at a pressure ∼3.0 GPa. The change of conduction mechanism from ionic to electronic may be explained by means of pressure-induced valence change of W⁶⁺→W⁵⁺, which results in electron transfer between W⁵⁺-W⁶⁺ sites at high pressure.     

High pressure X-ray diffraction study of ReS2

The high-pressure behavior of rhenium disulfide (ReS₂) has been investigated to 51.0 GPa by in situ synchrotron X-ray diffraction in a diamond anvil cell at room temperature. The results demonstrate that the ReS₂ triclinic phase is stable up to 11.3 GPa, at which pressure the ReS₂ transforms to a new high-pressure phase, which is tentatively identified with a hexagonal lattice in space group P6?m2. The high-pressure phase is stable up to the highest pressure in this study (51.0 GPa) and not quenchable upon decompression to ambient pressure. The compressibility of the triclinic phase exhibits anisotropy, meaning that it is more compressive along interlayer directions than intralayer directions, which demonstrates the properties of the weak interlayer van der Waals interactions and the strong intralayer covalent bonds. The largest change in the unit cell angles with increasing pressures is the increase of β, which indicates a rotation of the sulfur atoms around the rhenium atoms during the compression. Fitting the experimental data of the triclinic phase to the third-order Birch-Murnaghan EOS yields a bulk modulus of K_OT=23±4 GPa with its pressure derivative K_OT′= 29±8, and the second-order yields K_OT=49±3 GPa.     

Phase transitions in CsHSO4 up to 2.5 GPa: Impedance spectroscopy under pressure

Phase transitions in CsHSO₄ at pressures up to 2.5 GPa have been studied with the help of electrical impedance measurements. The phase boundaries have been identified with the help of calculated activation energies of electrical conductivity and dielectric relaxation time. The derived temperatures of phase transition from the low conductive phase II into super ionic phase I at pressure less than 1 GPa confirm the previous results of Ponyatovski? et al. (1985) [4] and Friesel et al. (1989) [27]. The phase diagram derived in this study for pressure larger than 1 GPa differs from the data of Ponyatovski? et al. (1985) [4]. The phase transitions IV-VI and VI-I occur at higher temperatures having significantly larger Clapeyron slope. The phase VII was not identified from heating cycle and appears only under cooling between phases I and VI. The phase VIII was detected at 2.5 GPa at T<350 K and only during heating.     

High-pressure powder diffraction study of TaO2F

TaO₂F, with a ReO₃-type structure, has been studied at up to 12.8 GPa using monochromatic synchrotron powder diffraction and diamond anvil cells. Two-phase transitions at ∼0.7 and 4 GPa were observed on compression. Below ∼0.7 GPa the cubic material was found to have a bulk modulus (K₀) of 36(3) GPa (K_p fixed at 4.0), similar to that reported for NbO₂F but much smaller than that of ReO₃. Immediately above 0.7 GPa on compression, the diffraction data were not fully consistent with a VF₃-type structure as previously proposed for NbO₂F. On decompression, the data between 8 and 4 GPa could be satisfactorily attributed to a single R-3c phase with a VF₃-type structure and an average bulk modulus of 60(2) GPa.     

Melting curve of silicon to 15 GPa determined by two-dimensional angle-dispersive diffraction using a Kawai-type apparatus with X-ray transparent sintered diamond anvils

The melting curve of silicon has been determined up to 15 GPa using a miniaturized Kawai-type apparatus with second-stage cubic anvils made of X-ray transparent sintered diamond. Our results are in good agreement with the melting curve determined by electrical resistivity measurements [V.V. Brazhkin, A.G. Lyapin, S.V. Popova, R.N. Voloshin, Nonequilibrium phase transitions and amorphization in Si, Si/GaAs, Ge, and Ge/GaSb at the decompression of high-pressure phases, Phys. Rev. B 51 (1995) 7549] up to the phase I (diamond structure)—phase II (β-tin structure)—liquid triple point. The triple point of phase XI (orthorhombic, Imma)—phase V (simple hexagonal)—liquid has been constrained to be at 14.4(4) GPa and 1010(5) K. These results demonstrate that the combination of X-ray transparent anvils and monochromatic diffraction with area detectors offers a reliable technique to detect melting at high pressures in the multianvil press.     

Pressure-induced phase transformations in l-alanine crystals

Raman scattering and synchrotron X-ray diffraction have been used to investigate the high-pressure behavior of l-alanine. This study has confirmed a structural phase transition observed by Raman scattering at 2.3 GPa and identified it as a change from orthorhombic to tetragonal structure. Another phase transformation from tetragonal to monoclinic structure has been observed at about 9 GPa. From the equation of state, the zero-pressure bulk modulus and its pressure derivative have been determined as (31.5±1.4) GPa and 4.4±0.4, respectively.     

Resistance anomaly and structural disorder in NiSi2 under high pressure

Results of X-ray diffraction, electrical resistance, thermoelectric power measurements and electronic band structure calculations on NiSi₂ under high pressure are reported. The thermoelectric power (TEP) changes sign near 0.5 GPa (from +30 to −20 μV/K). As the pressure is increased, the value of TEP increases further in magnitude and near 7 GPa it becomes −50 μV/K. The pressure vs. resistance curve measured up to 30 GPa using diamond anvil (DAC)-based technique exhibits a broad hump near 12 GPa and exhibits hysteresis on pressure release. The ADXRD patterns up to 42 GPa show a gradual irreversible loss of long-range order in NiSi₂ with the diffraction lines progressively broadening under pressure. The FWHM of the diffraction lines show a rapid increase in the half-widths close to 0.5 GPa and also near 12 GPa. The computed band structure at a compression (without any disorder) corresponding to 12 GPa, exhibits an electronic topological transition (ETT). The rapid increase in disorder above 12 GPa implies that the ETT may be facilitating the structural disorder. It is suggested that the pressure drives the material through a region of entropic and energetic barriers and induces disorder in the material.     

X-ray diffraction study of molybdenum diselenide to 35.9 GPa

In situ high-pressure angle dispersive synchrotron X-ray diffraction studies of molybdenum diselenide (MoSe₂) were carried out in a diamond-anvil cell to 35.9 GPa. No evidence of a phase transformation was observed in the pressure range. By fitting the pressure-volume data to the third-order Birch-Murnaghan equation of state, the bulk modulus, K_0T, was determined to be 45.7±0.3 GPa with its pressure derivative, K′_0T, being 11.6±0.1. It was found that the c-axis decreased linearly with pressure at a slope of −0.1593 when pressures were lower than 10 GPa. It showed different linear decrease with the slope of a −0.0236 at pressures higher than 10 GPa.     

Raman spectra for hydrogen hydrate under high pressure: Intermolecular interactions in filled ice Ic structure

Raman studies of a high-pressure structure of hydrogen hydrate, a filled ice Ic structure, were performed using a diamond anvil cell in the pressure range 3.2-44.1 GPa. The Raman spectra of a vibron revealed that extraction of hydrogen molecules from the filled ice Ic structure occurred above 20 GPa. In addition, the Raman spectra of a roton revealed that a rotation of hydrogen molecules in the filled ice Ic structure was suppressed at around 20 GPa and then the rotation recovered, and the rotation of hydrogen molecules was suppressed again above 35.5 GPa. These results indicate that intermolecular interactions increased between guest hydrogen molecules and host water molecules at around 20 and 35.5 GPa. These intermolecular interactions were considered to be induced to stabilize the filled ice Ic structure. Above 40 GPa, symmetrization of hydrogen bond was considered to contribute to the stability of hydrogen hydrate.     

First principles study of structural stability,electronic structure and mechanical properties of ReN and TcN

The crystal structure, structural stability, electronic and mechanical properties of ReN and TcN are investigated using first principles calculations. We have considered five different crystal structures: NaCl, zinc blende (ZB), NiAs, tungsten carbide (WC) and wurtzite (WZ). Among these ZB phase is found to be the lowest energy phase for ReN and TcN at normal pressure. Pressure induced structural phase transitions from ZB to WZ phase at 214 GPa in ReN and ZB to NiAs phase at 171 GPa in TcN are predicted. The electronic structure reveals that both ReN and TcN are metallic in nature. The computed elastic constants indicate that both the nitrides are mechanically stable. As ReN in NiAs phase has high bulk and shear moduli and low Poisson's ratio, it is found to be a potential ultra incompressible super hard material.     

Phase transition of Ta2NiO6 with the trirutile-type structure under high pressure and high temperature

High-pressure phase transition of Ta₂NiO₆ with the trirutile-type structure was investigated from the viewpoint of crystal chemistry. A new quenchable high-pressure phase was found in the pressure range higher than 7 GPa and 900°C. The high-pressure phase has an orthorhombic cell (a=4.797(1) Å, b=5.153(2) Å and c=14.85(1) Å and space group; Abm2), and it is more dense by 9.6% than the trirutile-structured phase. Infrared spectra of the trirutile-type phase and the high-pressure phase show that Ni²⁺ ions in the high-pressure phase are still in octahedral sites. The crystal structure of the high-pressure phase is considered as a cation-ordering trifluorite-type structure, which can be stabilized by a crystal field effect of Ni²⁺ ions.     

Structural stability of tin clathrates under high pressure

High pressure Raman scattering experiments have been performed for Rb₈Sn₄₄□₂ in order to investigate the pressure induced phase transition. At pressures of 6.0 and 7.5 GPa, Raman spectrum was drastically changed, indicating the phase transitions. The irreversibility of the spectral change and the disappearance of Raman peak observed at 7.5 GPa strongly suggest the occurrence of irreversible amorphization.     

Compression of silver in a diamond anvil cell: Pressure dependences of strength and grain size from X-ray diffraction data

Two silver samples, coarse grained (c-Ag, grain size 300±30 nm) and nanocrystalline (n-Ag, grain size 55±6 nm), are compressed in a diamond anvil cell in separate experiments. The pressure is increased in steps of ∼3 GPa and the diffraction pattern recorded at each pressure. The grain size and compressive strength are determined from the analysis of the diffraction line-widths. The grain size of c-Ag decreases rapidly from 300±30 nm at ambient pressure to 40±8 nm at 15 GPa, and then gradually to 20±3 nm at 40 GPa. After pressure release to ambient condition, the grain size is 25±4 nm. The strength at ambient pressure is 0.18±0.05 GPa and increases to 1.0±0.3 GPa at 40 GPa. The grain size of n-Ag decreases from 55±6 nm at ambient pressure to 17±4 nm at 15 GPa and to 14±3 nm at 55 GPa. After release of pressure to ambient condition, the grain size is 50±7 nm. The strength increases from 0.51±0.07 GPa at ambient pressure to 3.5±0.4 GPa at 55 GPa. The strength is found to vary as the inverse of the square-root of the grain size. The results of the present measurements agree well with the grain-size dependence of strength derived from the hardness versus grain size data at ambient pressure available in the literature.     

Photoluminescence properties of Sm-doped BaBr2 under hydrostatic pressure

Photoluminescence spectra of Sm²⁺-doped BaBr₂ have been measured under hydrostatic pressures up to 17 GPa at room temperature. In the low pressure range a red-shift of the broad 5d-4f transition of −145 cm⁻¹/GPa is observed. From 5 to 8 GPa a phase mixture of the initial orthorhombic phase and the high-pressure monoclinic phase gives rise to two 5d-4f bands, which are strongly overlapping. Above 8 GPa the crystal is completely transformed to its high-pressure phase where two different Sm²⁺ sites exist, but only one broad 5d-4f transition is detected. It exhibits a red-shift of −36 cm⁻¹/GPa. In addition, the line shifts of the ⁵D₀→⁷F_J (J=0, 1, 2) transitions are investigated. Linear shifts of −19 cm⁻¹/GPa for J=0, 2 and of −13 cm⁻¹/GPa for J=1 are observed in the pressure range from 0 to 5 GPa.