Free‐radical copolymerization of vinyl esters using fluoroalcohols as solvents: The solvent effect on the monomer reactivity ratio

Free‐radical copolymerizations of vinyl acetate (VAc = M₁) and other vinyl esters (= M₂) including vinyl pivalate (VPi), vinyl 2,2‐bis(trifluoromethyl)propionate (VF6Pi), and vinyl benzoate (VBz) with fluoroalcohols and tetrahydrofuran (THF) as the solvents were investigated. The fluoroalcohols affected not only the stereochemistry but also the polymerization rate. The polymerization rate was higher in the fluoroalcohols than in THF. The accelerating effect of the fluoroalcohols on the polymerization was probably due to the interaction of the solvents with the ester side groups of the monomers and growing radical species. The difference in the monomer reactivity ratios (r₁, r₂) in THF and 2,2,2‐trifluoroethanol was relatively small for all reaction conditions and for the monomers tested in this work, whereas r₁ increased in the VAc‐VF6Pi copolymerization and r₂ decreased in the VAc‐VPi copolymerization when perfluoro‐tert‐butyl alcohol was used as the solvent. These results were ascribed to steric and monomer‐activating effects due to the hydrogen bonding between the monomers and solvents. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 220–228, 2000     

Controlled random and alternating copolymerization of (meth)acrylates,acrylonitrile, and (meth)acrylamides with vinyl ethers by organotellurium‐, organostibine‐, and organobismuthine‐mediated living radical polymerization reactions

Random and alternating copolymerizations of acrylates, methacrylates, acrylonitorile, and acrylamides with vinyl ethers under organotellurium‐, organostibine‐, and organobismuthine‐mediated living radical polymerization (TERP, SBRP, and BIRP, respectively) have been studied. Structurally well‐controlled random and alternating copolymers with controlled molecular weights and polydispersities were synthesized. The highly alternating copolymerization occurred in a combination of acrylates and vinyl ethers and acrylonitorile and vinyl ethers by using excess amount of vinyl ethers over acrylates and acrylonitorile. On the contrary, alternating copolymerization did not occur in a combination of acrylamides and vinyl ethers even excess amount of vinyl ethers were used. The reactivity of polymer‐end radicals to a vinyl ether was estimated by the theoretical calculations, and it was suggested that the energy level of singly occupied molecular orbital (SOMO) of polymer‐end radical species determined the reactivity. By combining living random and alternating copolymerization with living radical or living cationic polymerization, new block copolymers, such as (PBA‐alt‐PIBVE)‐block‐(PtBA‐co‐PIBVE), PBA‐block‐(PBA‐alt‐PIBVE), and (PTFEA‐alt‐PIBVE)‐block‐PIBVE, with controlled macromolecular structures were successfully synthesized. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Synthesis and hydrogel formation of fluorine‐containing amphiphilic ABA triblock copolymers

Fluorine‐containing amphiphilic ABA triblock copolymers, poly(2‐hydroxyethyl vinyl ether)‐block‐poly[2‐(2,2,3,3,3‐pentafluoropropoxy)ethyl vinyl ether]‐block‐poly(2‐hydroxyethyl vinyl ether) [poly(HOVE‐b‐PFPOVE‐b‐HOVE)] (HFH), poly[2‐(2,2,3,3,3‐pentafluoropropoxy)ethyl vinyl ether]‐block‐poly(2‐hydroxyethyl vinyl ether)‐block‐poly[2‐(2,2,3,3,3‐pentafluoropropoxy)ethyl vinyl ether] [poly(PFPOVE‐b‐HOVE‐b‐PFPOVE)] (FHF), and poly(n‐butyl vinyl ether)‐block‐poly(2‐hydroxyethyl vinyl ether)‐block‐poly(n‐butyl vinyl ether) [poly(NBVE‐b‐HOVE‐b‐NBVE)] (LHL), were synthesized, and their behavior in water was investigated. The aforementioned polymers were prepared by sequential living cationic polymerization of 2‐acetoxyethyl vinyl ether (AcOVE) and PFPOVE or NBVE, followed by hydrolysis of acetyl groups in polyAcOVE. FHF and LHL formed a hydrogel in water, whereas HFH gave a homogeneous aqueous solution. In addition, the gel‐forming concentration of FHF was much lower than that of corresponding LHL. Surface‐tension measurements of the aqueous polymer solutions revealed that all the triblock copolymers synthesized formed micelles or aggregates above about 1.0 × 10^?4 mol/L. The surface tensions of HFH and FHF solutions above the critical micelle concentration were lower than those of LHL, indicating high surface activity of fluorine‐containing triblock copolymers. Small‐angle X‐ray scattering measurements revealed that HFH formed a core‐shell sperical micelle in 1 wt % aqueous solutions, whereas the other block copolymers caused more conplicated assembly in the solutions. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 3751–3760, 2001     

Radical copolymerization of novel trifluorovinyl ethers with ethyl vinyl ether and vinyl acetate: Estimating reactivity ratios and understanding reactivity behavior of the propagating radical

Two novel trifluorovinyl ether (TFVE) monomers were copolymerized with either ethyl vinyl ether (EVE) or vinyl acetate (VAc) in a redox‐initiated aqueous emulsion: 1‐(2‐phenoxyethoxy)‐1,2,2‐trifluoroethene (Ph‐TFVE) and 1‐[2‐(2‐ethoxyethoxy)ethoxy]‐1,2,2‐trifluoroethene (Et‐TFVE). Previous studies demonstrated a propensity for radical hydrogen abstraction from the oligoether pendant group during the homopolymerization of Et‐TFVE with continued propagation of the resulting radical, thereby providing the rationale to investigate the copolymerization of our new TFVEs with EVE or VAc. Reactivity ratios were estimated using the error‐in‐variables model from a series of bulk free radical copolymerizations of Ph‐TFVE with EVE or VAc. The reactivity ratios were r_Ph‐TFVE = 0.25 ± 0.07, r_EVE = 0.016 ± 0.04; r_Ph‐TFVE = 0.034 ± 0.04, r_VAc =0.89 ±0.08. Partial hydrolysis of polymers containing VAc to vinyl alcohol (VA) resulted in two terpolymers: poly(Ph‐TFVE‐co‐VAc‐co‐VA) and poly(Et‐TFVE‐co‐VAc‐co‐VA), respectively. We investigated the possibility of hydrogen abstraction from VAc during polymerization by comparing the molar mass before and after hydrolysis. Abstraction from VAc was not apparent during polymerization; however, abstraction from the oligoether pendant group of Et‐TFVE was again evident and was more significant for those copolymers having a greater fraction of Et‐TFVE in the monomer feed. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 1344–1354, 2000     

Controlled polymerization of methyl acrylate for high‐molecular‐weight polymers by pentafluorophenylbis(triflyl)methane‐promoted group transfer polymerization using triisopropylsilyl ketene acetal

The group transfer polymerization (GTP) of methyl acrylate (MA) was studied using pentafluorophenylbis(triflyl)methane (C₆F₅CHTf₂) as the organocatalyst and 1‐trimethylsiloxy‐, 1‐triethylsiloxy‐, and 1‐triisopropylsiloxy‐1‐methoxy‐2‐methyl‐1‐propene (MTS^Me, MTS^Et, and MTS^iPr, respectively) as the initiators. The C₆F₅CHTf₂‐promoted GTP of MA using MTS^iPr proceeded in a living nature to produce poly(methyl acrylate)s (PMAs) with controlled molecular weights and narrow molecular weight distributions, which allowed the synthesis of high‐molecular‐weight PMA with the number‐average molecular weight (M_n(SEC)) of up to 108,000 and the polydispersity (M_w/M_n) of 1.07. The matrix‐assisted laser desorption/ionization time‐of‐flight mass spectrometry measurement revealed that the obtained PMA possessed the chain end structure that originated from MTS^iPr, showing that the C₆F₅CHTf₂‐promoted GTP of MA proceeded without any side reactions. In addition, the kinetic study and the postpolymerization experiment supported the living manner of the polymerization. Moreover, the block copolymerization of MA and n‐butyl acrylate (nBA) smoothly proceeded to afford the well‐defined PMA‐block‐poly(n‐butyl acrylate) (PnBA). © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Free-radical polymerization of vinyl esters using fluoroalcohols as solvents: Effect of monomer structure on stereochemistry

Free-radical polymerization of vinyl esters including vinyl propionate (VPr), vinyl isobutylate (ViBu), vinyl 2,2-dimethylbutylate (VDMB), vinyl 2,2-dimethylvalerate (VDMV), vinyl 2,2-bis(trifluoromethyl)propionate (VF6Pi), and vinyl benzoate (VBz) was carried out using fluoroalcohols as solvents, and the tacticity of the obtained polymers was determined by NMR analysis of the produced poly(vinyl alcohol) (PVA). The polymerization of VPr, ViBu, VDMB, and VDMV, which are bulkier than VAc, in fluoroalcohols afforded polymers rich in heterotacticity (up to mr = 61%) similar to that of vinyl pivalate (VPi) whereas VAc is known to give a syndiotactic polymer under the reaction conditions used here. The polymerization of VF6Pi, which is the bulkiest among the monomers used in this study, gave a polymer rich in syndiotacticity in bulk and in fluoroalcohols regardless of the structure of the solvents. On the other hand, the polymerization of VBz in fluoroalcohols gave polymers with a higher isotacticity (up to mm = 33%) than bulk polymerization. Thus the monomer structure strongly affected the stereochemistry of the free-radical polymerization of vinyl esters in fluoroalcohols. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 2677–2683, 1999     

Grafting of polycaprolactone onto poly(ethylene‐co‐vinyl alcohol) and application to polyethylene‐based bioerodable blends

Poly(ethylene‐co‐vinyl acetate) (EVA) powders containing 10 and 20 wt % of vinyl acetate (VAc) units was saponified in ethanol/KOH solution in a heterogeneous manner. Intermolecular interaction between vinyl alcohol(VOH) units in the produced poly(ethylene‐co‐vinyl alcohol) (EVOH) promoted the crystallization of intervening segments composed of ethylene units. Ring opening polymerization of caprolactone (CL) in the presence of EVOH gave EVOH‐g‐PCL graft copolymers with relatively short chain branches. Even though the graft copolymerization was carried out in a homogeneous solution, all the VOH units were not equally reactive for the PCL grafting. And the unreacted VOH units decreased very slowly with the graft copolymerization time. EVOH‐g‐PCL decreased the domain size of the dispersed phase in low density polyethylene (PE)/biodegradable master batch (MB) blends, and thus increased their tensile properties significantly. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 2561–2569, 2002     

Amphiphilic block copolymer self‐assemblies of poly(NVP)‐b‐poly(MDO‐co‐vinyl esters): Tunable dimensions and functionalities

Functional, degradable polymers were synthesized via the copolymerization of vinyl acetate (VAc) and 2‐methylene‐1,3‐dioxepane (MDO) using a macro‐xanthate CTA, poly(N‐vinylpyrrolidone), resulting in the formation of amphiphilic block copolymers of poly(NVP)‐b‐poly(MDO‐co‐VAc). The behavior of the block copolymers in water was investigated and resulted in the formation of self‐assembled nanoparticles containing a hydrophobic core and a hydrophilic corona. The size of the resultant nanoparticles was able to be tuned with variation of the hydrophilic and hydrophobic segments of the core and corona by changing the incorporation of the macro‐CTA as well as the monomer composition in the copolymers, as observed by Dynamic Light Scattering, Static Light Scattering, and Transmission Electron Microscopy analyses. The concept was further applied to a VAc derivative monomer, vinyl bromobutanoate, to incorporate further functionalities such as fluorescent dithiomaleimide groups throughout the polymer backbone using azidation and “click” chemistry as postpolymerization tools to create fluorescently labeled nanoparticles. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 2699–2710     

Synthesis and characterization of block copolymers by metal‐ and solvent‐free ring‐opening polymerization of cyclic carbonates initiated from PEG‐based surfactants

Ring‐opening polymerizations of trimethylene carbonate (TC) and 2,2‐dimethyltrimethylene carbonate (DTC) are initiated from hydroxyl‐terminated polyethylene glycol (PEG) and PEG‐based surfactants (Triton X‐100 or Triton X‐405) in the absence of any catalysts. The metal‐ and solvent‐free polymerizations proceed under melt at 150 °C, affording Triton X‐100‐block‐poly(TC) with M_n of 1400–5200 and Triton X‐100‐block‐poly(DTC) with M_n of 1800–7100 in excellent yields. The molecular weights and the comonomer composition of the resulting copolymers are controlled by the feed ratios of the monomers to the initiators, confirmed by gel permeation chromatography and ¹H NMR spectroscopy. The solubilities of the block copolymers composed of hydrophilic PEG segment and hydrophobic poly(TC) or poly(DTC) segment depend on both the compositions and the components. For example, Triton X‐100‐block‐poly (TC) (TC/EG = 9.5/9.5) and Triton X‐405‐block‐poly(TC) (TC/EG = 28/40, 46/40) milky suspend in water, while Triton X‐405‐block‐poly(TC) (TC/EG = 9.7/40) dissolves in water. A dynamic light scattering study reveals that the particle distribution of a copolymer, Triton X‐405‐block‐poly(TC) (TC/EG = 9.7/40) in water, has a monodisperse unimodal pattern ranging from 92 to 368 nm. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 1985–1996, 2006     

Sequence‐controlled cationic ring‐opening copolymerization of spiroorthocarbonate and oxetane

Pseudo block and triblock copolymers were synthesized by the cationic ring‐opening copolymerization of 1,5,7,11‐tetraoxaspiro[5.5]undecane (SOC1) with trimethylene oxide (OX) via one‐shot and two‐shot procedures, respectively. When SOC1 and OX were copolymerized cationically with boron trifluoride etherate (BF₃OEt₂) as an initiator in CH₂Cl₂ at 25 °C, OX was consumed faster than SOC1. SOC1 was polymerized from the OX‐rich gradient copolymer produced in the initial stage of the copolymerization to afford the corresponding pseudo block copolymer, poly [(OX‐grad‐SOC1)‐b‐SOC1]. We also succeeded in the synthesis of a pseudo triblock copolymer by the addition of OX during the course of the polymerization of SOC1 before its complete consumption, which provided the corresponding pseudo triblock copolymer, poly[SOC1‐b‐(OX‐grad‐SOC1)‐b‐SOC1]. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 3233–3241, 2006     

Synthesis of poly(tert‐butyl acrylate‐block‐vinyl acetate) copolymers by combining ATRP and RAFT polymerizations

The synthesis of poly(tert‐butyl acrylate‐block‐vinyl acetate) copolymers using a combination of two living radical polymerization techniques, atom transfer radical polymerization (ATRP) and reversible addition‐fragmentation chain transfer (RAFT) polymerization, is reported. The use of two methods is due to the disparity in reactivity of the two monomers, viz. vinyl acetate is difficult to polymerize via ATRP, and a suitable RAFT agent that can control the polymerization of vinyl acetate is typically unable to control the polymerization of tert‐butyl acrylate. Thus, ATRP was performed to make poly(tert‐butyl acrylate) containing a bromine end group. This end group was subsequently substituted with a xanthate moiety. Various spectroscopic methods were used to confirm the substitution. The poly(tert‐butyl acrylate) macro‐RAFT agent was then used to produce (tert‐butyl acrylate‐block‐vinyl acetate). © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 7200–7206, 2008     

Synthesis of amphiphilic poly(methyl methacrylate‐ b‐ethylene oxide) copolymers from monohydroxy telechelic poly(methyl methacrylate) as macroinitiator

The synthesis of well‐defined poly(methyl methacrylate)‐block‐poly(ethylene oxide) (PMMA‐b‐PEO) dibock copolymer through anionic polymerization using monohydroxy telechelic PMMA as macroinitiator is described. Living anionic polymerization of methyl methacrylate was performed using initiators derived from the adduct of diphenylethylene and a suitable alkyllithium, either of which contains a hydroxyl group protected with tert‐butyldimethylsilyl moiety in tetrahydrofuran (THF) at ?78 °C in the presence of LiClO₄. The synthesized telechelic PMMAs had good control of molecular weight with narrow molecular weight distribution (MWD). The ¹H NMR and MALDI‐TOF MS analysis confirmed quantitative functionalization of chain‐ends. Block copolymerization of ethylene oxide was carried out using the terminal hydroxyl group of PMMA as initiator in the presence of potassium counter ion in THF at 35 °C. The PMMA‐b‐PEO diblock copolymers had moderate control of molecular weight with narrow MWD. The ¹H NMR results confirm the absence of trans‐esterification reaction of propagating PEO anions onto the ester pendants of PMMA. The micellation behavior of PMMA‐b‐PEO diblock copolymer was examined in water using ¹H NMR and dynamic light scattering. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 2132–2144, 2008     

Synthesis of amphiphilic star block copolymers via diethyldithiocarbamate‐mediated living radical polymerization

(AB)_f star block copolymers were synthesized by the radical polymerization of a poly(t‐butyl acrylate)‐block‐poly(methyl methacrylate) diblock macroinitiator with ethylene glycol dimethacrylate in methanol under UV irradiation. Diblock macroinitiators were prepared by diethyldithiocarbamate‐mediated sequential living radical copolymerization initiated by (4‐cyano‐4‐diethyldithiocarbamyl)pentanoic acid under UV irradiation. The arm number (f) was controlled by the variation of the initial concentration of the diblock initiator. It was found from light scattering data that such star block copolymers (f ≥ 344) not only took a spherical shape but also formed a single molecule in solution. Subsequently, we derived amphiphilic [arm: poly(acrylic acid)‐block‐poly(methyl methacrylate)] star block copolymers by the hydrolysis of poly(t‐butyl acrylate) blocks. These amphiphilic star block copolymers were soluble in water because the external blocks were composed of hydrophilic poly(acrylic acid) chains. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 3321–3327, 2006     

Synthesis of poly(dimethylsiloxane)‐containing diblock and triblock copolymers by the combination of anionic ring‐opening polymerization of hexamethylcyclotrisiloxane and nitroxide‐mediated radical polymerization of methyl acrylate,isoprene, and styrene

Poly(dimethylsiloxane)‐containing diblock and triblock copolymers were prepared by the combination of anionic ring‐opening polymerization (AROP) of hexamethylcyclotrisiloxane (D₃) and nitroxide‐mediated radical polymerization (NMRP) of methyl acrylate (MA), isoprene (IP), and styrene (St). The first step was the preparation of a TIPNO‐based alkoxyamine carrying a 4‐bromophenyl group. The alkoxyamine was then treated with Li powder in ether, and AROP of D₃ was carried out using the resulting lithiophenyl alkoxyamine at room temperature, giving functional poly(D₃) with M_w/M_n of 1.09–1.16. NMRPs of MA, St, and IP from the poly(D₃) at 120 °C gave poly(D₃‐b‐MA), poly(D₃‐b‐St), and poly(D₃‐b‐IP) diblock copolymers, and subsequent NMRPs of St from poly(D₃‐b‐MA) and poly(D₃‐b‐IP) at 120 °C gave poly(D₃‐b‐MA‐b‐St) and poly(D₃‐b‐IP‐b‐St) triblock copolymers. The poly(dimethylsiloxane)‐containing diblock and triblock copolymers were analyzed by ¹H NMR and size exclusion chromatography. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 6153–6165, 2005     

Cobalt‐mediated radical polymerization routes to poly(vinyl ester) block copolymers

Cobalt‐mediated radical polymerizations (CMRPs) utilizing redox initiation are demonstrated to produce poly(vinyl ester) homopolymers derived from vinyl pivalate (VPv) and vinyl benzoate (VBz), and their block copolymers with vinyl acetate (VAc). Combining anhydrous Co(acac)₂, lauroyl peroxide, citric acid trisodium salt, and VPv at 30 °C results in controlled polymerizations that yield homopolymers with M_n = 2.5–27 kg/mol with M_w/M_n = 1.20–1.30. Homopolymerizations of scrupulously purified VBz proceed with lower levels of control as evidenced by broader polydispersities over a range of molecular weights (M_n = 4–16 kg/mol; M_w/M_n = 1.34–1.65), which may be interpreted in terms of the decreased nucleophilicity of these less electron donating propagating polymer chain ends. Based on these results, we demonstrate that sequential CMRP reactions present a viable route to microphase separated poly(vinyl ester) block copolymers as shown by small‐angle X‐ray scattering analyses. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

Organometallic mediated radical polymerization of vinyl acetate with Fe(acac)2

The radical polymerization of vinyl acetate (VAc) is moderated by iron(II) acetylacetonate (Fe(acac)₂) by the organometallic route (OMRP), as well as by degenerative transfer polymerization (DTP) when in the presence of excess radicals, through the formation of thermally labile organometallic Fe^III dormant species. The poly(vinyl acetate) (PVAc)‐Fe^III(acac)₂ dormant species has been isolated in the form of an oligomer and characterized by ¹H NMR, EPR, and IR methods, and then used as a single‐component initiator for the OMRP of VAc. The degree of polymerization of this isolated oligomeric species demonstrates the limited ability of Fe(acac)₂, relative to the Co(acac)₂ congener, to rapidly trap the growing PVAc radical chain. Control under OMRP conditions is improved by the presence of Lewis bases, especially PMe₂Ph. On the other hand, iron(II) phthalocyanine inhibits the radical polymerization of VAc completely. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013 , 51, 3494–3504     

Synthesis and characterizations of the four‐armed amphiphilic block copolymer S[poly(2,3‐dihydroxypropyl acrylate)‐block‐poly(methyl acrylate)]4

The polymers poly[(2,2‐dimethyl‐1,3‐dioxolane‐4yl) methyl acrylate] (PDMDMA) and four‐armed PDMDMA with well‐defined structures were prepared by the polymerization of (2,2‐dimethyl‐1,3‐dioxolane‐4yl) methyl acrylate (DMDMA) in the presence of an atom transfer radical polymerization (ATRP) initiator system. The successive hydrolyses of the polymers obtained produced the corresponding water‐soluble polymers poly(2,3‐dihydroxypropyl acrylate) (PDHPA) and four‐armed PDHPA. The controllable features for the ATRP of DMDMA were studied with kinetic measurements, gel permeation chromatography (GPC), and NMR data. With the macroinitiators PDMDMA–Br and four‐armed PDMDMA–Br in combination with CuBr and 2,2′‐bipyridine, the block polymerizations of methyl acrylate (MA) with PDMDMA were carried out to afford the AB diblock copolymer PDMDMA‐b‐MA and the four‐armed block copolymer S{poly[(2,2‐dimethyl‐1,3‐dioxolane‐4yl) methyl acrylate]‐block‐poly(methyl acrylate)}₄, respectively. The block copolymers were hydrolyzed in an acidic aqueous solution, and the amphiphilic diblock and four‐armed block copolymers poly(2,3‐dihydroxypropyl acrylate)‐block‐poly(methyl acrylate) were prepared successfully. The structures of these block copolymers were verified with NMR and GPC measurements. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 3062–3072, 2001     

Living copolymerization of ethylene with norbornene by fluorinated enolato‐imine titanium catalyst

Complex [Ti(κ²‐N,O‐{2,6‐F₂C₆H₃N?C(Me)C(H) ?C(CF₃) O})₂Cl₂] ( 1 ) was evaluated as catalyst for living copolymerization of ethylene (E) with norbornene (N) upon activation with dried methylaluminoxane (d‐MAO) at temperatures between 25 and 90 °C. Copolymerization performed at different [N]/[E] feed ratios afforded stereoirregular alternating high molar mass P(E‐co‐N) with narrow molar mass distribution. The living nature of E‐co‐N copolymerization by 1 /d‐MAO was demonstrated by kinetics at 50 °C. This catalyst system was used for the synthesis of block copolymers such as polyethylene (PE)‐block‐P(E‐co‐N) with a crystalline PE block and an amorphous P(E‐co‐N) block as well as P(E‐co‐N)₁‐block‐P(E‐co‐N)₂, having different norbornene contents in the segments and thus having different T_g values. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Investigation of the radical copolymerization and terpolymerization of maleic anhydride and norbornenes by an in situ 1H NMR analysis of kinetics and by the mercury method: Evidence for the lack of charge‐transfer‐complex propagation

The radical copolymerization of electron‐deficient maleic anhydride (MA) and electron‐rich norbornene (NB) derivatives with 2,2′‐azobis(isobutyronitrile) (AIBN) in dioxane‐d₈ has been monitored in situ by ¹H NMR spectroscopy with free induction decays recorded every 30 min at 60, 70, or 84 °C. The ratios of the monomer pairs were varied in some cases. The NB derivatives employed in this study included bicyclo[2.2.1]hept‐2‐ene (NB), t‐butyl 5‐norbornene‐2‐carboxylate, methyl 5‐norbornene‐2‐methyl‐2‐carboxylate, and ethyl tetracyclo[4.4.0.1^2,5.1^7,10]dodec‐3‐ene‐8‐carboxylate. Decomposition of AIBN, consumption of the monomers, feed ratios, endo/exo ratios, copolymer compositions, and copolymer yields were studied as a function of polymerization time. Furthermore, a homopolymerizable third monomer (t‐butyl methacrylate, methacrylic acid, t‐butyl acrylate, or acrylic acid) was added to the NB/MA 1/1 system, revealing that the methacrylic monomer polymerizes rapidly in the early stage and that the ratio of MA to NB in the terpolymer strongly deviates from 1/1. In contrast, however, the acrylic monomers are more uniformly incorporated into the polymer. Nevertheless, these studies indicate that MA and NB do not always behave as a pair in radical polymerization and disproves the commonly believed charge‐transfer mechanism. Electron‐deficient fumaronitrile was also included in the kinetics study. To further understand the copolymerization mechanism, MA and NB were competitively reacted with a cyclohexyl radical generated by the treatment of cyclohexylmercuric chloride with sodium borohydride (mercury method). A gas chromatographic analysis of the reaction mixtures has revealed that a cyclohexyl radical reacts with MA almost exclusively in competition and that the cyclohexyl adduct of MA essentially accounts for all the products in a mass balance experiment, eliminating a possibility of the formation of an adduct involving the MA–NB charge‐transfer complex. Thus, the participation of a charge‐transfer complex in the copolymerization of MA and NB cannot be important. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 3521–3542, 2000     

Copper(0)‐mediated radical copolymerization of vinyl acetate and acrylonitrile in DMSO at ambient temperature

In this work, Cu(0)‐mediated radical copolymerization of vinyl acetate (VAc) and acrylonitrile (AN) was explored. The polymerization was carried out at 25°C with 2,2′‐bipyridine as ligand and dimethyl sulfoxide as solvent. The copolymerization proceeded smoothly producing moderately controlled molecular weights at low VAc feed ratios. The high VAc feed ratios generated low polymerization rate and poorly controlled molecular weights. FTIR, ¹H NMR, and differential scanning calorimetry confirmed the successful obtaining of the copolymers. Based on ¹H NMR spectra, the reactivity ratios of VAc and AN were calculated to be 0.003 and 1.605, respectively. This work conveyed the first example for the Cu(0)‐mediated radical polymerization of AN and VAc, wherein VAc cannot be homopolymerized by Cu(0)‐mediated radical polymerization technique. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012