Vinyltitanium as an initiator for the polymerization of acetylene

The preparation of lustrous conducting polyacetylene films by the polymerization of acetylene with vinyltitanium species as initiators was studied. Organotitanium species were generated by the alkylation of titanium vinylcarbene complexes with tert‐butyl chloride. Solid‐state ¹³C NMR and IR analyses of the obtained polyacetylene indicated that polyacetylene with a trans configuration was produced. The use of titanocene(II) species Cp₂Ti[P(OEt)₃]₂ and titanium vinylcarbene complexes for the preparation of polyacetylene films was also studied. The morphology of the films and the mechanisms of polymerization are discussed. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 2663–2669, 2002     

Derivatization of propene/methyloctadiene copolymers: A flexible approach to side‐chain‐functionalized polypropenes

The copolymerization of propene with 7‐methyl‐1,6‐octadiene (MOD) catalyzed by Cp*TiMe₃/B(C₆F₅)₃ ( A ) and rac‐C₂H₄(Ind)₂ZrCl₂/methylaluminoxane ( B ) in toluene under 1 bar propene gave copolymers with unsaturated side chains. Under these conditions, catalyst A produced copolymers with an atactic backbone structure of type 1 , with 3.5–19.6 mol % MOD incorporation and weight‐average molecular weight = 0.7–2.7 × 10⁵. Using catalyst B , copolymers 2 with 0.4–3.8 mol % MOD incorporation were prepared. The comonomer incorporation was a linear function of the feed ratio. The titanium catalyst A had a significantly higher affinity for MOD than the sterically more hindered zirconocene B . Postpolymerization modification of the side‐chain C?C bond allowed the facile introduction of a wide variety of functional groups. Epoxidation and especially ozonolysis of the C?C bond, to give ? CHO and ? COOH functionalized copolymers, proved to be very facile routes to functionalized polypropenes. According to monitoring by NMR, most of these transformations proceed in an essentially quantitative conversion. As an example of potential applications of such polymers, polypropenes with covalently attached dyes were prepared that are suitable for blending. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 1484–1497, 2002     

Highly stereo‐efficient synthesis and luminescence properties of novel trans‐regular vinylene– silylene–thiophene polymers

The novel trans‐stereo‐regular silylene–thiophene derivatives ( 4 , 5 ) with perfect consecutive silylene–arylene–silylene–vinylene linkage were synthesized via silylative coupling polycondensation of 2,5‐bis(vinyldimethylsilyl)thiophene ( 2 ) or 5,5′‐bis(vinyldimethylsilyl)‐2,2′‐bithiophene ( 3 ) catalyzed by ruthenium‐hydride complex [RuHCl(CO)(PCy₃)₂] ( 1 ). Their spectroscopic, absorption, and luminescence properties were characterized and compared with those of model compounds containing thiophene or bithiophene chromophores. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 127–137, 2008     

Electric‐field‐induced molecular alignment of side‐chain liquid‐crystalline polyacetylenes containing biphenyl mesogens

Electric‐field‐induced molecular alignments of side‐chain liquid‐crystalline polyacetylenes [? {HC?C[(CH₂)_mOCO‐biph‐OC₇H₁₅]}? , where biph is 4,4′‐biphenylyl and m is 3 (PA3EO7) or 9 (PA9EO7)] were studied with X‐ray diffraction and polarized optical microscopy. An orientation as high as 0.84 was obtained for PA9EO7. Furthermore, the molecular orientation of PA9EO7 was achieved within a temperature range between the isotropic‐to‐smectic A transition temperature and 115 °C, and this suggested that the orientational packing was affected by the thermal fluctuation of the isotropic liquid and the mobility of the mesogenic moieties. The maximum achievable orientation for PA9EO7 was much greater than that for PA3EO7. This was the first time that the electric‐field‐induced molecular orientation of a side‐chain liquid‐crystalline polymer with a stiff backbone was studied. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1333–1341, 2004     

Ring‐opening metathesis polymerization of cis‐cyanocyclooct‐4‐ene: Search for active catalysts,variation of monomer to catalyst ratios and monomer concentrations

The ring‐opening metathesis polymerization (ROMP) of cis‐cyanocyclooct‐4‐ene initiated by ruthenium‐based catalysts of the first, second, and third generation was studied. For the polymerization with the second generation Grubbs catalyst [RuCl₂(?CHPh)(H₂IMes)(PCy₃)] (H₂IMes = N,N′‐bis(mesityl)‐4,5‐dihydroimidazol‐2‐ylidene), the critical monomer concentration at which polymerization occurs was determined, and variation of monomer to catalyst ratios was performed. For this catalyst, ROMP of cis‐cyanocyclooct‐4‐ene did not show the features of a living polymerization as M_n did not linearly increase with increasing monomer conversion. As a consequence of slow initiation rates and intramolecular polymer degradation, molar masses passed through a maximum during the course of the polymerization. With third generation ruthenium catalysts (which contain 3‐bromo or 2‐methylpyridine ligands), polymerization proceeded rapidly, and degradation reactions could not be observed. Contrary to ruthenium‐based catalysts of the second and third generation, a catalyst of the first generation was not able to polymerize cis‐cyanocyclooct‐4‐ene. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Syntheses and properties of dumbbell‐shaped POSS derivatives linked by luminescent π‐conjugated units

Dumbbell‐shaped isobutyl‐substituted 1,2‐bis(4‐vinylphenyl)acetylene‐linked POSS (DA1), 9,10‐bis(4‐vinylphenyl)ethynyl)anthracene‐linked POSS (DA2), and 5,5″‐bis((4‐vinyl)phenyl)ethynyl)‐2,2′:5′2″‐terthiophene‐linked POSS (DA3), and corresponding model compounds were synthesized by cross metathesis and Sonogashira reaction, and their film formability, and thermal and optical properties were examined. The dumbbell structures of the obtained compounds were confirmed by ¹H‐, ¹³C‐, and ²⁹Si‐NMR and MALDI‐TOF‐MS analysis. The dumbbell‐shaped POSS compounds gave optically transparent films. All the model compounds, however, formed opaque films. All the films were emissive under UV irradiation. The dumbbell structures minimize longer wavelength shifts and improve emission efficiency of the luminescent π‐conjugated linker units in their solid states compared with the model compounds. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012.     

Norbornene‐functionalized PEO‐b‐PCL: A versatile platform for mikto‐arm star,umbrella‐like,and comb‐like graft copolymers

Well‐defined in‐chain norbornene‐functionalized poly(ethylene oxide)‐b‐poly(?‐caprolactone) copolymers (NB‐PEO‐b‐PCL) were synthesized from a dual clickable containing both hydroxyl‐ and alkyne‐reactive groups, namely heterofunctional norbornene 3‐exo‐(2‐exo‐(hydroxymethyl)norborn‐5‐enyl)methyl hexynoate. A range of NB‐PEO‐b‐PCL copolymers were obtained using a combination of orthogonal organocatalyzed ring‐opening polymerization (ROP) and click copper‐catalyzed azide–alkyne cycloaddition (CuAAC). Ring‐opening metathesis polymerization (ROMP) of NB‐PEO‐b‐PCL macromonomers using ruthenium‐based Grubbs’ catalysts provides comb‐like and umbrella‐like graft copolymers bearing both PEO and PCL grafts on each monomer unit. Mikto‐arm star A₂B₂ copolymers were obtained through a new strategy based on thiol–norbornene photoinitiated click chemistry between 1,3‐propanedithiol and NB‐PEO‐b‐PCL. The results demonstrate that in‐chain NB‐PEO‐b‐PCL copolymers can be used as a platform to prepare mikto‐arm star, umbrella‐, and comb‐like graft copolymers. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55 , 4051–4061     

Alternating π‐conjugated copolymer of dithiafulvene with 2,2′‐bipyridyl units

A π‐conjugated polymer containing a dithiafulvene unit and a bipyridyl unit was prepared by cycloaddition polymerization of aldothioketene derived from 5,5′‐diethynyl‐2,2′‐bipyridine. Ultraviolet–visible (UV–vis) absorption spectra showed that the π‐conjugation system of the polymer expanded more effectively than that of a benzene analogue of poly(dithiafulvene) obtained from 1,4‐diethynylbenzene. Cyclic voltammetry measurements indicated that the dithiafulvene–bipyridyl polymer was a weaker electron‐donor polymer than the benzene analogue. These results supported the idea that the incorporation of the electron‐accepting bipyridyl moiety into conjugated poly(dithiafulvene) induced an intramolecular charge‐transfer (CT) effect between the units. Treatment of the dithiafulvene–bipyridyl polymer with bis(2,2′‐bipyridyl)dichlororuthenium (II) [Ru(bpy)₂Cl₂] afforded a ruthenium–polymer complex. A cyclic voltammogram of the complex showed broad redox peaks, which indicated electronic interaction between the dithiafulvene and tris(bipyridyl) ruthenium complex. The dithiafulvene–bipyridyl polymer formed CT complexes with 7,7,8,8‐tetracycanoquinodimethane (TCNQ) in dimethyl sulfoxide. The UV–vis absorption indicated that the resulting CT complex contained anion radical of TCNQ and partially charge‐transferred TCNQ. The polymer showed an unusually high electrical conductivity of 3.1 × 10^?4 S/cm in its nondoped state due to the effective donor–acceptor interaction between the bipyridine unit and the dithiafulvene unit. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 4083–4090, 2001     

Acyclic diene metathesis polymerization of 2,5‐dialkyl‐1,4‐divinylbenzene with molybdenum or ruthenium catalysts: Factors affecting the precise synthesis of defect‐free,high‐molecular‐weight trans‐poly(p‐phenylene vinylene)s

Factors affecting the syntheses of high‐molecular‐weight poly(2,5‐dialkyl‐1,4‐phenylene vinylene) by the acyclic diene metathesis polymerization of 2,5‐dialkyl‐1,4‐divinylbenzenes [alkyl = n‐octyl ( 2 ) and 2‐ethylhexyl ( 3 )] with a molybdenum or ruthenium catalyst were explored. The polymerizations of 2 by Mo(N‐2,6‐Me₂C₆H₃) (CHMe₂ Ph)[OCMe(CF₃)₂]₂ at 25 °C was completed with both a high initial monomer concentration and reduced pressure, affording poly(p‐phenylene vinylene)s with low polydispersity index values (number‐average molecular weight = 3.3–3.65 × 10³ by gel permeation chromatography vs polystyrene standards, weight‐average molecular weight/number‐average molecular weight = 1.1–1.2), but the polymerization of 3 was not completed under the same conditions. The synthesis of structurally regular (all‐trans), defect‐free, high‐molecular‐weight 2‐ethylhexyl substituted poly(p‐phenylene vinylene)s [poly 3 ; degree of monomer repeating unit (DP_n) = ca. 16–70 by ¹H NMR] with unimodal molecular weight distributions (number‐average molecular weight = 8.30–36.3 × 10³ by gel permeation chromatography, weight‐average molecular weight/number‐average molecular weight = 1.6–2.1) and with defined polymer chain ends (as a vinyl group, ? CH?CH₂) was achieved when Ru(CHPh)(Cl)₂(IMesH₂)(PCy₃) or Ru(CH‐2‐OⁱPr‐C₆H₄)(Cl)₂(IMesH₂) [IMesH₂ = 1,3‐bis(2,4,6‐trimethylphenyl)‐2‐imidazolidinylidene] was employed as a catalyst at 50 °C. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 6166–6177, 2005     

Luminescent mesogen jacketed poly(1‐alkyne) bearing lateral terphenyl with hexyloxy tail

Mesogen jacketed liquid crystalline poly(1‐alkyne) and poly(1‐phenyl‐1‐alkyne) linked pendants of terphenyl mesogens with hexyloxy tails at the waist position (? {RC?C? [(CH₂)₃OOC‐terpheyl‐(OC₆H₁₃)₂]}_n? , where R?H, PHATP(OC6)2 ; R?C₆H₅, PPATP(OC6)2 ) were synthesized. The influences of structural variations on the thermal, mesomorphic, and luminescent properties were investigated. Polymerizations of all monomers are carried out by WCl₆‐Ph₄Sn catalysts successfully. The polymers are stable (T_d ≥ 340 °C) and soluble in common solvents. The monomers and polymers show enantiotropic SmA phases in the heating and cooling processes, and the lateral side chains of the mesogenic units are perpendicular to the main chain. The “jacket effect” of chromophoric terphenyl core “shell” around the main chain also contributes to polymers with high photoluminescence, and the pendant‐to‐backbone energy transfer path is involved in the luminescence process of this polymers. In comparison with monosubstituted polyacetylene PHATP(OC6)2 , the disubstituted polyacetylene PPATP(OC6)2 shows better photoluminescence in both THF solution and film, and exhibited about 40 nm red‐shifted than PHATP(OC6)2 , indicating that the “jacket effect” of terphenyl mesogens forces poly(1‐phenyl‐1‐alkyne) backbone to extend in a more planar conformation with a better conjugation. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

Novel high‐performance polymer memory devices containing (OMe)2tetraphenyl‐p‐phenylenediamine moieties

The functional polyimide (OMe)₂TPPA‐6FPI ( PI ) and the polyamide (OMe)₂TPPA‐6FPA ( PA ) consisting of electron‐donating N,N′‐bis(4‐aminophenyl)‐N,N′‐di(4‐methoxylphenyl)1,4‐phenylenediamine [(OMe)₂TPPA‐diamine] for memory application were prepared in this study. These polyimide and polyamide memory devices were fabricated with the sandwich configuration of indium tin oxide (ITO)/polymer/Al, and could be switched from the initial low‐conductivity (OFF) state to the high‐conductivity (ON) state with high ON/OFF current ratios of 10⁷ and 10⁹, respectively. PI exhibited dynamic random access memory (DRAM) performance, whereas PA showed static random access memory (SRAM) behavior. To get more insight into the memory behaviors of these two different types of polymer memory devices, molecular simulation on the basic unit was carried out. Furthermore, the differences of highest occupied molecular orbital (HOMO) energy level, lowest unoccupied molecular orbital (LUMO) charge density isosurfaces, dipole moment, and linkage conformation between PI and PA were found to affect the volatile memory behavior. Both polymer memory devices revealed excellent stability with long operation time of 10⁴ s at continuous applied voltage of ‐2 V. The effect of polymer thickness on the volatile memory behavior of PA was also investigated in this study. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Crosslinked polynorbornene particles synthesis by ring‐opening metathesis polymerization in dispersion

This article proposes the first report on the synthesis of nanometric crosslinked polynorbornene particles by ring‐opening metathesis polymerization in dispersion using ruthenium‐based complex (PCy₃)₂Cl₂Ru?CHPh as initiator. Stable but raspberry‐shaped particles were obtained. In this study, a particular attention was paid to the influence of the crosslinker nature and addition mode on reaction kinetics and morphology of the latex particles. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Synthesis,complex formation,and dilute‐solution associative behavior of linear poly(methacrylic acid)‐graft‐poly(2‐ethyl‐2‐oxazoline)*

Poly(methacrylic acid) (PMA) and poly(2‐ethyl‐2‐oxazoline) (PEOZO) are a polyacid/polybase pair capable of forming reversible, pH‐responsive, hydrogen‐bonding complexes stabilized by hydrophobic effects in aqueous media. Linear PMA was modified with long‐chain (number‐average molecular weight: 10,000) PEOZO via statistical coupling reactions in organic media to prepare a series of PMA‐graft‐PEOZO copolymers. Potentiometric titrations revealed that the presence of tethered PEOZO markedly increases the pK_a values for PMA‐g‐PEOZO copolymers as compared with simple PMA/PEOZO mixtures at degrees of ionization, α, between 0.0 and 0.1. The dilute‐solution PMA–PEOZO intramolecular association has been probed by monitoring the PEOZO NMR spin–spin (T₂) relaxation as a function of pH. Covalently attached PEOZO side chains participate in complexation at higher values of α than untethered PEOZO. Surprisingly, most PEOZO side chains did not take part in hydrogen bonding at low α, and the highest level of PEOZO incorporation induced a decrease in the number of PMA/PEOZO hydrogen bonds. The polymer self‐diffusion as a function of α was measured with dynamic light scattering. At low pH, the copolymers had no charge and they were in a collapsed form. At high pH, the expected conformational expansion of the PMA units was enhanced at moderate levels of PEOZO incorporation. However, the highest PEOZO incorporation induced the onset of intramolecular associations between PEOZO units along the copolymer chains. Low shear rheometry and light scattering measurements were used in conjunction with the T₂ NMR measurements to propose a model consistent with the aforementioned behavior. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 2520–2533, 2004     

Synthesis and properties of monodisperse multi‐triarylamine‐substituted oligothiophenes and 4,7‐bis(2′‐oligothienyl)‐2,1,3‐benzothiadiazoles for organic solar cell applications

Two novel series of monodisperse multi‐triarylamine‐substituted oligothiophenes, G ₂ ‐ OT ( n )‐ G ₂ with thiophene unit (n) varying from 6 to 8, and 4,7‐bis(2′‐oligothienyl)‐2,1,3‐benzothiadiazoles G ₂ ‐ OT ( n ) BTD ‐ G ₂ (n = 2, 4, 6) have been synthesized by the Suzuki coupling reactions. With an elongation of alkyl‐substituted oligothiophene core or an incorporation of benzothiadiazole into the central core, the absorption and emission spectra of G ₂ ‐ OT ( n )‐ G ₂ and G ₂ ‐ OT ( n ) BTD ‐ G ₂ series red‐shift substantially with the optical gap reducing to 1.95 eV for G ₂ ‐ OT ( 6 ) BTD ‐ G ₂ . Alkyl‐substitution onto oligothiophene backbone not only improves the solubility of the highly extended dendrimers but also renders coplanarity of the dendritic oligothiophene backbone at the excited state, which results in the enhancement of fluorescence quantum efficiency. The bulk heterojunction solar cells using these newly synthesized dendritic oligothiophenes as a donor material and [6,6]‐phenyl C₆₁‐butyric acid methyl ester (PCBM) as an acceptor material were fabricated and investigated which showed an increase in device performance as compared with those of the lower homologues. On increasing the loading of PCBM from 1.5 to 3 times in the active layer, there was also an enhancement in device performance with power conversion efficiencies of as‐fabricated solar cells increasing from 0.18% to 0.32%. In addition, proper annealing procedure could significantly improve the device performance of the dendrimer‐based photovoltaic cell. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 137–148, 2009     

Synthesis and polymerization of phenylacetylene having two carbazole units and properties of the formed polymer

Novel carbazole‐containing acetylene monomer, 1‐(3‐ethynyl‐9‐carbazoyl)?4‐(9‐carbazoyl)benzene 1 was synthesized, polymerized, and copolymerized with phenylacetylene ( PA ) using [(nbd)RhCl]₂‐Et₃N, Rh⁺(nbd)[η⁶‐C₆H₅B^–(C₆H₅)₃], and WCl₆‐Ph₄Sn as catalysts. Polymers with number‐average molecular weights ranging from 7800 to 33,200 were obtained in 60%–quantitative yields. The absorption band edge of poly( 1 ‐co‐ PA ) ( 1 :PA = 8:2) was positioned at a wavelength longer than those of 1 and polyvinylcarbazole. Poly( 1 ‐co‐ PA ) ( 1:PA = 8:2) emitted fluorescence with 60% quantum yield. Poly( 1 ‐co‐ PA ) ( 1:PA = 8:2) worked as a hole transport material of an OLED with tris(8‐hydroxyquinoline)aluminum (Alq3) as an emission material. © 2015 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 2015 , 53, 1245–1251     

Copolymerization of propylene with 1,3‐butadiene using isospecific zirconocene catalysts

Poly(propylene‐ran‐1,3‐butadiene) was synthesized using isospecific zirconocene catalysts and converted to telechelic isotactic polypropylene by metathesis degradation with ethylene. The copolymers obtained with isospecific C₂‐symmetric zirconocene catalysts activated with modified methylaluminoxane (MMAO) had 1,4‐inserted butadiene units ( 1,4‐BD ) and 1,2‐inserted units ( 1,2‐BD ) in the isotactic polypropylene chain. The selectivity of butadiene towards 1,4‐BD incorporation was high up to 95% using rac‐dimethylsilylbis(1‐indenyl)zirconium dichloride (Cat‐A)/MMAO. The molar ratio of propylene to butadiene in the feed regulated the number‐average molecular weight (M_n) and the butadiene contents of the polymer produced. Metathesis degradations of the copolymer with ethylene were conducted with a WCI₆/SnMe₄/propyl acetate catalyst system. The ¹H NMR spectra before and after the degradation indicated that the polymers degraded by ethylene had vinyl groups at both chain ends in high selectivity. The analysis of the chain scission products clarified the chain end structures of the poly(propylene‐ran‐1,3‐butadiene). © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 5731–5740, 2007     

Synthesis and photophysical properties of soluble low‐bandgap thienothiophene polymers with various alkyl side‐chain lengths

We report the facile synthesis and characterization of a class of thienothiophene polymers with various lengths of alkyl side chains. A series of 2‐alkylthieno[3,4‐b]thiophene monomers (Ttx) have been synthesized in a two‐step protocol in an overall yield of 28–37%. Poly(2‐alkylthieno[3,4‐b]thiophenes) (PTtx, alkyl: pentyl, hexyl, heptyl, octyl, and tridecyl) were synthesized by oxidative polymerization with FeCl₃ or via Grignard metathesis (GRIM) polymerization methods. The polymers are readily soluble in common organic solvents. The polymers synthesized by GRIM polymerization method (PTtx‐G) have narrower molecular weight distribution (?) with lower molecular weight (M_n) than those synthesized by oxidative polymerization (PTtx‐O). The band structures of the polymers with various lengths of alkyl side chains were investigated by UV–vis spectroscopy, cyclic voltammetry, and ultraviolet photoelectron spectroscopy. These low‐bandgap polymers are good candidates for organic transistors, organic light‐emitting diodes, and organic photovoltaic cells. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Specific properties of in situ ruthenium‐catalyzed polyamide 12/polydimethylsiloxane compatibilized blend

The main objective of this work focused on the chemical modification of polyamide 12 (PA12) properties through the reaction with a hydride‐terminated polydimethylsiloxane (PDMS‐SiH). The investigated PA12/PDMS‐SiH blend was compatibilized by ruthenium derivative catalyzed hydrosilylation reaction in molten state. This original route enhanced interfacial adhesion and avoid PDMS‐SiH leaching phenomenon between the two immiscible phases. More specifically, the size of PDMS‐SiH domains in the blend decreased from around 4 μm to 800 nm and from 30 to 1 μm after compatibilization with 10 and 20 wt % PDMS‐SiH, respectively. For the best compatibilized PA12/PDMS‐SiH blend, the introduction of PDMS lowered the surface free energy and the PA12‐based blend turned from hydrophilic to hydrophobic behavior, as evidenced by the water contact angle measurements. Gas permeability and CO₂/H₂ and CO₂/He gas selectivity were also improved with the increase in PDMS content. Besides, the mechanical properties were enhanced with 13% increase in Young's modulus after in situ compatibilization with 15 wt % PDMS‐SiH. Thermal stability was also improved after compatibilization as the initial degradation temperature of reactive blends obviously increased compared with nonreactive ones. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2018 , 56, 978–988     

Ring‐opening metathesis polymerization of functionalized cyclooctene by a ruthenium‐based catalyst in ionic liquid

This paper describes the synthesis of a novel monomer of 5‐substituted cyclooctene with the pendant of imidazolium salt (7) and the ring‐opening metathesis polymerization of the functionalized cyclooctenes ( 4 and 7 ) in CH₂Cl₂ and ionic liquid [bmim][PF₆] by a ruthenium‐based catalyst RuCl₂(PCy₃)(SIMes)(CHPh) (2). The polymerization, which was carried out in ionic liquid, afforded improved control over the molecular weight (M_n) and polydispersity of the resultant products (PDI <1.4). Furthermore, to facilitate the GPC measurement for molecular weight of polymers, the charged polymers (poly‐ 7 ) were hydrolyzed to give uncharged polymers (poly‐ 4 *) by removing the imidazolium pendant from the polymer chains. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 3986–3993, 2007     

Influence of ortho‐substituents on the synthesis and properties of poly(phenylacetylene)s

The phenylacetylene derivatives (4‐decyloxyphenyl)acetylene ( M1 ), (4‐decyloxy‐2‐methylphenyl)acetylene ( M2 ), and (4‐decyloxy‐2,6‐dimethylphenyl)acetylene ( M3 ) were polymerized by the well‐defined Schrock‐type initiator Mo[N‐2,6‐i‐Pr₂C₆H₃)(CHCMe₂Ph)[OCMe(CF₃)₂]₂ ( I1 ) and by the ill‐defined quaternary system MoOCl₄–n‐Bu₄Sn–EtOH–quinuclidine (1:1:2:1) ( I2 ). Comparison of the compatibility of the initiators with the different monomers revealed a correlation of the size of the ortho‐substituents and the polymerizability of the monomers. M1 and M2 readily polymerized employing I1 , but conversion of the sterically demanding monomer M3 remained incomplete. However, the use of I2 led to high monomer conversions and polymer yields only in case of M2 and M3 . The steric bulkiness of the ortho‐substituents also decisively affected the maximum effective conjugation length (N_eff) of the polymers and hence their absorption maximum (λ_max) as well as their solution stability as shown by UV–vis and GPC studies, respectively. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 4466–4477, 2004