Block and random copolymerization of ε‐caprolactone,L‐, and rac‐lactide using titanium complex derived from aminodiol ligand

A series of di‐ and triblock copolymers [poly(L ‐lactide‐b‐ε‐caprolactone), poly(D,L ‐lactide‐b‐ε‐caprolactone), poly(ε‐caprolactone‐b‐L ‐lactide), and poly(ε‐caprolactone‐b‐L ‐lactide‐b‐ε‐caprolactone)] have been synthesized successfully by sequential ring‐opening polymerization of ε‐caprolactone (ε‐CL) and lactide (LA) either by initiating PCL block growth with living PLA chain end or vice versa using titanium complexes supported by aminodiol ligands as initiators. Poly(trimethylene carbonate‐b‐ε‐caprolactone) was also prepared. A series of random copolymers with different comonomer composition were also synthesized in solution and bulk of ε‐CL and D,L ‐lactide. The chemical composition and microstructure of the copolymers suggest a random distribution with short average sequence length of both the LA and ε‐CL. Transesterification reactions played a key role in the redistribution of monomer sequence and the chain microstructures. Differential scanning calorimetry analysis of the copolymer also evidenced the random structure of the copolymer with a unique T_g. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

A macromonomer approach to the synthesis of poly(1,1‐bis(ethoxycarbonyl)‐2‐vinyl cyclopropane‐graft‐dimethyl siloxane)

Poly(1,1‐bis(ethoxycarbonyl)‐2‐vinyl cyclopropane (ECVP)‐graft‐dimethyl siloxane) copolymers were prepared using a macromonomer approach. Poly(dimethyl siloxane) (PDMS) macromonomers were prepared by living anionic polymerization of cyclosiloxanes followed by sequential chain‐end capping with allyl chloroformate. These macromonomers were then copolymerized with ECVP. MALDI‐ToF mass spectrometry and ¹H NMR spectroscopy were used to show that the macromonomers had approximately 80% of the end groups functionalized with allyl carbonate groups. Gradient polymer elution chromatography showed that high yields of the graft copolymers were obtained, along with only small fractions of the PECVP and PDMS homopolymers. Differential scanning calorimetry showed that the low glass transition temperature (T_g) of the PDMS component could be maintained in the graft copolymers. However, the T_g was a function of polymer composition and the polymers produced had T_gs that ranged from ?50 to ?120 °C. © 2013 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

Synthesis and characterization of novel poly(ester carbonate)s based on pentaerythritol

Novel poly(ester carbonate)s were synthesized by the ring‐opening polymerization of L ‐lactide and functionalized carbonate monomer 9‐phenyl‐2,4,8,10‐tetraoxaspiro[5,5]undecan‐3‐one derived from pentaerythritol with diethyl zinc as an initiator. ¹H NMR analysis revealed that the carbonate content in the copolymer was almost equal to that in the feed. DSC results indicated that T_g of the copolymer increased with increasing carbonate content in the copolymer. Moreover, the protecting benzylidene groups in the copolymer poly(L ‐lactide‐co‐9‐phenyl‐2,4,8,10‐tetraoxaspiro[5,5]undecan‐3‐one) were removed by hydrogenation with palladium hydroxide on activated charcoal as a catalyst to give a functional copolymer, poly(L ‐lactide‐co‐2,2‐dihydroxylmethyl‐propylene carbonate), containing pendant primary hydroxyl groups. Complete deprotection was confirmed by ¹H NMR and FTIR spectroscopy. The in vitro degradation rate of the deprotected copolymers was faster than that of the protected copolymers in the presence of proteinase K. The cell morphology and viability on a copolymer film evaluated with ECV‐304 cells showed that poly(ester carbonate)s derived from pentaerythritol are good biocompatible materials suitable for biomedical applications. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45:1737 –1745, 2007     

Novel aliphatic poly(ester‐carbonate) with pendant allyl ester groups and its folic acid functionalization

A series of novel poly(ester‐carbonate)s bearing pendant allyl ester groups P(LA‐co‐MAC)s were prepared by ring‐opening copolymerization of L ‐lactide (LA) and 5‐methyl‐5‐allyloxycarbonyl‐1,3‐dioxan‐2‐one (MAC) with diethyl zinc (ZnEt₂) as initiator. NMR analysis investigated the microstructure of the copolymer. DSC results indicated that the copolymers displayed a single glass‐transition temperature (T_g), which was indicative of a random copolymer, and the T_g decreased with increasing carbonate content in the copolymer. Then NHS‐activated folic acid (FA) first reacted with 2‐aminoethanethiol to yield FA‐SH; grafting FA‐SH to P(LA‐co‐MAC) in the presence of TEA produced P(LA‐co‐MAC)/FA. The structure of P(LA‐co‐MAC)/FA and its precursor were confirmed by ¹H NMR and XPS analysis. Cell experiments showed that FA‐grafted P(LA‐co‐MAC) had improved adhesion and proliferation behavior of vero cells on the polymer films. Therefore, the novel FA‐grafted block copolymer is expected to find application in drug delivery or tissue engineering. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 1852–1861, 2008     

Synthesis and characterization of novel poly(ester‐carbonate)s by copolymerization of trans‐4‐hydroxy‐L‐proline with cyclic carbonate

The melt ring‐opening/condensation reaction of trans‐4‐hydroxy‐N‐benzyloxycarbonyl‐L‐proline (N‐CBz‐Hpr) with cyclic carbonate [trimethylene carbonate (tri‐MC) or tetramethylene carbonate (tetra‐MC)] at a wide range of molar fractions in the feed produced new degradable poly(ester‐carbonate)s. The influence of reaction conditions such as polymerization time and temperature on the yield and inherent viscosity of the copolymers was investigated. The polymerizations were carried out in bulk at 140 °C with 1.5 wt % stannous octoate as a catalyst for 30 h. The poly(ester‐carbonate)s obtained were characterized by Fourier transform infrared spectroscopy, ¹H NMR, differential scanning calorimetry, gel permeation chromatography, and Ubbelohde viscometry. The copolymers synthesized exhibited moderate molecular weights with rather narrow molecular weight distributions. The values of the glass‐transition temperature (T_g) of the copolymers depend on the molar fractions of cyclic carbonate. For the poly(N‐CBz‐Hpr‐co‐tri‐MC) system, with a decreased tri‐MC content from 93 to 16 mol %, the T_g increased from ?10 to 60 °C. Similarly, for the poly(N‐CBz‐Hpr‐co‐tetra‐MC) system, when the tetra‐MC content decreased from 80 to 8 mol %, the T_g increased from ?18 to 52 °C. The relationship between the poly(N‐CBz‐Hpr‐co‐tri‐MC) T_g and the compositions was in approximation with the Fox equation. In vitro degradation of these poly(N‐CBz‐Hpr‐co‐tri‐MC)s was evaluated from weight‐loss measurements. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 1435–1443, 2003     

Poly(N‐phenylmaleimide‐co‐acrylic acid)–copper(II) and poly(N‐phenylmaleimide‐co‐acrylic acid)–cobalt(II) complexes: Synthesis,characterization, and thermal behavior

The free‐radical copolymerization of N‐phenylmaleimide (N‐PhMI) with acrylic acid was studied in the range of 25–75 mol % in the feed. The interactions of these copolymers with Cu(II) and Co(II) ions were investigated as a function of the pH and copolymer composition by the use of the ultrafiltration technique. The maximum retention capacity of the copolymers for Co(II) and Cu(II) ions varied from 200 to 250 mg/g and from 210 to 300 mg/g, respectively. The copolymers and polymer–metal complexes of divalent transition‐metal ions were characterized by elemental analysis, Fourier transform infrared, ¹H NMR spectroscopy, and cyclic voltammetry. The thermal behavior was investigated with differential scanning calorimetry (DSC) and thermogravimetry (TG). The TG and DSC measurements showed an increase in the glass‐transition temperature (T_g) and the thermal stability with an increase in the N‐PhMI concentration in the copolymers. T_g of poly(N‐PhMI‐co‐AA) with copolymer composition 46.5:53.5 mol % was found at 251 °C, and it decreased when the complexes of Co(II) and Cu(II) at pHs 3–7 were formed. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 4933–4941, 2005     

Fire and Forget! One‐Shot Synthesis and Characterization of Block‐Like Statistical Terpolymers via Living Anionic Polymerization

Diphenylethylene (DPE) is a monomer which has attracted significant interest from academia and industry both in terms of copolymerization kinetics and for the potential to extend and tune the range of glass transition temperatures accessible for DPE‐containing copolymers. DPE can undergo (co)polymerization with a variety of other monomers by living anionic polymerization but is incapable of forming a homopolymer due to steric hindrance. DPE, being a sterically bulky monomer, results in dramatic increases in the glass transition temperature (T_g) of resulting copolymers, with a perfectly alternating copolymer of styrene and DPE having a T_g of ~180 °C. Herein we report for the first time, the outcome of the statistical terpolymerization of butadiene, styrene, and DPE—a one‐pot, one‐shot, commercially scalable reaction using monomers of wide industrial importance. This extremely facile approach produces copolymers with a block‐like structure, which undergo microphase separation, possess a high T_g glassy “block” and are virtually indistinguishable from analogous block terpolymers made by the traditional sequential addition of monomers approach. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019 , 57, 382–394     

Glass transition temperature of allyl methacrylate‐n‐butyl acrylate gradient copolymers in dependence on chemical composition and molecular weight

Glass transition temperatures (T_gs) of P(AMA‐co‐BA) copolymers and the corresponding homopolymers, where AMA is allyl methacrylate and BA is n‐butyl acrylate, obtained by means of atom transfer radical polymerization were measured using differential scanning calorimetry. Because of the (pseudoliving) nature of this polymerization technique an increase in molecular weight (MW) is produced as the reaction progresses, which gives rise to an increase in T_gs. This increment can be adequately described by the Fox–Flory's equation in both homopolymers. However, in the spontaneous gradient copolymers of P(AMA‐co‐BA), the expected increase in T_g with the augment of the monomer conversion is compensated by the enrichment of BA as the polymerization reaction progresses. These opposite effects with respect to the T_g values almost balance each other, and therefore no significant influence on the MW or on conversion is found. This fact establishes that T_gs can be used to describe the profile of these gradient copolymers, and can be theoretically determined because of its dependence on the molar fraction in the copolymer. From this dependence on chemical composition along with the experimental behavior, a prediction of the T_g variation with the MW was performed. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 1845–1855, 2007     

Synthesis and characterization of perfluoro‐3‐methylene‐2,4‐dioxabicyclo[3,3,0] octane: Homo‐ and copolymerization with fluorovinyl monomers

The synthesis of perfluoro‐3‐methylene‐2,4‐dioxabicyclo[3,3,0] octane (D), its radical homopolymerization, and copolymerization with fluoroolefins are presented. Fluorodioxolane (D) was synthesized through direct fluorination of the corresponding hydrocarbon precursor in a fluorinated solvent by F₂/N₂ gas. It was polymerized in bulk using perfluorodibenzoyl peroxide as the initiator. The resulting homopolymer had a limited solubility in fluorinated solvents, and its glass transition temperature (T_g) was in the range of 180–190 °C. The polymeric films prepared by casting from hot hexafluorobenzene (HFB) solution were transparent with low refractive index (1.329 at 633 nm). These films were thermally stable (T_d > 350 °C), and were hard and brittle. The copolymers of monomer (D) were prepared with fluorovinyl monomers such as chlorotrifluoroethylene (CTFE), perfluoropropyl vinyl ether, perfluoromethyl vinyl ether, and vinylidene fluoride. The kinetics of radical copolymerization of monomer (D) with CTFE led to the assessment of the reactivity ratios of both comonomers: r_D = 3.635 and r_CTFE = 0.737 at 74 °C, respectively. The copolymers obtained were soluble in HFB and perfluoro‐2‐butyltetrahydrofuran, with T_g in the range of 84–145 °C depending on the copolymer composition. The films of the copolymers were flexible and clear with a low refractive index (1.3350–1.3770 at 532 nm). © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 6571–6578, 2009     

Synthesis of gradient copolymers with simultaneously tailor‐made chain composition distribution and glass transition temperature by semibatch ATRP: From modeling to application

Recent studies have demonstrated that gradient copolymers exhibit unique thermal properties. Although these properties can be determined by copolymer composition, other factors such as chain and sequence lengths and their distributions can also influence them. Accordingly, the synthesis of gradient copolymers requires simultaneously tailor‐made chain structure and thermal properties. In this work, we carried out a systematic study on the preparation of poly(methyl methacrylate‐grad‐2‐hydroxyethyl methacrylate) [poly(MMA‐grad‐HEMA)] with synchronously tailor‐made chain composition distribution and glass transition temperature (T_g) through semibatch atom transfer radical polymerization. First, a comprehensive model for simultaneously predicting gradient copolymer microstructure and T_g was presented using the concept of pseudo‐kinetic rate coefficients and Johnston equation. The model was validated by comparing simulation results with the classical reference data. Furthermore, the model was used to guide the experimental synthesis of the poly(MMA‐grad‐HEMA) gradient copolymers potentially as excellent damping material. The thermal properties of these gradient copolymer samples were evaluated. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Statistical copolymers of norbornene and 5‐vinyl‐2‐norbornene by a ditungsten complex mediated ring‐opening metathesis Polymerization: Synthesis,thermal properties,and kinetics of thermal decomposition

Statistical copolymers of norbornene (NBE) with 5‐vinyl‐2‐norbornene (VNBE) were prepared by ring‐opening metathesis polymerization, employing the triply bonded ditungsten complex Na[W₂(μ‐Cl)₃Cl₄(THF)₂].(THF)₃. NMR measurements revealed that the side vinyl groups of the VNBE monomer remain intact during the copolymerization reaction. The reactivity ratios were estimated using the Finemann–Ross (FR), the inverted FR, and the Kelen–Tüdos graphical methods. Structural parameters of the copolymers were obtained by calculating the dyad sequence fractions, which were derived using the monomer reactivity ratios. The glass transition temperatures, T_g, of the copolymers were measured by differential scanning calorimetry measurements and were examined in the frame of several theoretical equations allowing the prediction of these T_g values. The best fit was obtained using methods that take into account the monomer sequence distribution of the copolymers. Finally, the kinetics of the thermal decomposition of the copolymers was studied by thermogravimetric analysis in the frame of the Ozawa–Flynn–Wall and Kissinger methods. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013 , 51, 4835–4844     

Highly active bifunctional cobalt‐salen complexes for the synthesis of poly(ester‐block‐carbonate) copolymer via terpolymerization of carbon dioxide,propylene oxide,and norbornene anhydride isomer: Roles of anhydride conformation consideration

This article describes an efficient synthetic route of defined reactive polyester‐block‐polycarbonate copolymers, utilizing a bifunctional SalenCoNO₃ complex as catalyst for the single‐step terpolymerization of norbornene anhydride (NA), propylene oxide, and carbon dioxide. The geometric isomer of NA plays an important role in polymerization efficacy and the resulting polymer microstructure, including carbonate content, sequence isomer of polycarbonate moiety, and molecular weight. A hydroxyl‐functionalized polyester–polycarbonate block copolymer was synthesized by a thiol‐ene reaction. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 789–795     

Synthesis and characterization of amphiphilic block copolymers with allyl side‐groups

The synthesis of a new cyclic carbonate monomer containing an allyl group was reported and its biodegradable amphiphilic block copolymer, poly(ethylene glycol)‐block‐poly(L ‐lactide‐co‐5‐methyl‐5‐allyloxycarbonyl‐propylene carbonate) [PEG‐b‐P(LA‐co‐MAC)] was synthesized by ring‐opening polymerization (ROP) of L ‐lactide (LA) and 5‐methyl‐5‐allyloxycarbonyl‐1,3‐dioxan‐2‐one (MAC) in the presence of poly (ethylene glycol) as a macroinitiator, with diethyl zinc as a catalyst. ¹³C NMR and ¹H NMR were used for microstructure identification of the copolymers. The copolymer could form micelles in aqueous solution. The core of the micelles is built of the hydrophobic P(LA‐co‐MAC) chains, whereas the shell is set up by the hydrophilic PEG blocks. The micelles exhibited a homogeneous spherical morphology and unimodal size distribution. By using the cyclic carbonate monomer containing allyl side‐groups, crosslinking of the PEG‐b‐P(LA‐co‐MAC) inner core was possible. The adhesion and spreading of ECV‐304 cells on the copolymer were better than that on PLA films. Therefore, this biodegradable amphiphilic block copolymer is expected to be used as a biomaterial for drug delivery and tissue engineering. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 5518–5528, 2007     

Synthesis and characterization of cationic copolymers of butylacrylate and [3‐(methacryloylamino)‐propyl]trimethylammonium chloride

Cationic copolymers of butylacrylate (BA) and [3‐(methacryloylamino)‐propyl]trimethylammonium chloride (MAPTAC) were synthesized by free‐radical‐solution polymerization in methanol and ethanol. An FT‐Raman Spectrometer and NMR were used to monitor the polymerization process. The copolymers were characterized by light scattering, NMR, DSC, and thermogravimetric analysis. It was found that random copolymers could be prepared, and the molar fractions of BA and cationic monomers in the copolymers were close to the feed ratios. The copolymer prepared in methanol had a higher molecular weight than that prepared in ethanol. As the cationic monomer content increased, the glass‐transition temperature (T_g) of the copolymer also increased, whereas the thermal stability decreased. The reactivity ratios for the monomers were evaluated. The copolymerization of BA (M₁) with MAPTAC (M₂) gave reactivity ratios such as r₁ = 0.92 and r₂ = 2.61 in ethanol as well as r₁ = 0.79 and r₂ = 0.90 in methanol. This study indicated that a random copolymer containing a hydrophobic monomer (BA) and a cationic hydrophilic monomer (MAPTAC) could be prepared in a proper polar solvent such as methanol or ethanol. © 2001 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 39: 1031–1039, 2001     

Synthesis and characterization of poly(arylene ether)s containing 6‐(4‐hydroxyphenyl)pyridazin‐3(2H)‐one or 6‐(4‐hydroxyphenyl)pyridazine moieties

A series of novel soluble pyridazinone‐ or pyridazine‐containing poly(arylene ether)s were prepared by a polycondensation reaction. The pyridazinone monomer, 6‐(4‐hydroxyphenyl)pyridazin‐3(2H)‐one ( 1 ), was synthesized from the corresponding acetophenone and glyoxylic acid in a simple one‐pot reaction. The pyridazinone monomer was successfully copolymerized with bisphenol A (BPA) or 1,2‐dihydro‐4‐(4‐hydroxyphenyl)phthalazin‐1(2H)‐one (DHPZ) and bis(4‐fluorophenyl)sulfone to form high‐molecular‐weight polymers. The copolymers had inherent viscosities of 0.5–0.9 dL/g. The glass‐transition temperatures (T_g's) of the copolymers synthesized with BPA increased with increasing content of the pyridazinone monomer. The T_g's of the copolymers synthesized from DHPZ with different pyridazinone contents were similar to those of the two homopolymers. The homopolymers showed T_g's from 202 to 291 °C by differential scanning calorimetry. The 5% weight loss temperatures in nitrogen measured by thermogravimetric analysis were in the range of 411–500 °C. 4‐(6‐Chloropyridazin‐3‐yl)phenol ( 2 ) was synthesized from 1 via a simple one‐pot reaction. 2 was copolymerized with 4,4′‐isopropylidenediphenol and bis(4‐fluorophenyl)sulfone to form high‐T_g polymers. The copolymers with less than 80 mol % pyridazinone or chloropyridazine monomers were soluble in chlorinated solvents such as chloroform. The copolymers with higher pyridazinone contents and homopolymers were not soluble in chlorinated solvents but were still soluble in dipolar aprotic solvents such as N‐methylpyrrolidinone. The soluble polymers could be cast into flexible films from solution. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 3328–3335, 2006     

Novel acrylic macromonomer with amphiphilic character derived from Triton X‐100: Radical copolymerization with methyl methacrylate and thermal properties

This article explores the synthesis of a novel methacrylic macromonomer with an amphiphilic character derived from poly(ethylene glycol) tert‐octylphenyl ether (MT) and its respective homopolymer. To know their reactivity in radical copolymerization reactions with methyl methacrylate (MMA), a model monomer (MTm) was synthesized to determine the reactivity ratios and compare them with the low molar fractions of copolymers of MT with MMA because they were difficult to isolate. They were r_MTm = 0.97 and r_MMA = 0.95. The compositional diagrams when representing the weight fraction of MT and MTm in the feed and the copolymer suggested that a clear correlation exists between the experimental points of the model monomer MTm and the macromonomer MT ones, suggesting that the length of the side poly(ethylene oxide) chain does not affect the reactivity of the methacrylic double bond in the prepared monomers for this type of polymerization reaction. The reactivity ratios of the copolymers have a tendency for the formation of random or Bernoullian copolymers. The glass‐transition temperatures (T_g's) of the prepared copolymers were determined by differential scanning calorimetry, deviated from the Fox equation, and discussed on the basis of treatments that consider the influence of the monomeric units along the copolymer chains, determining the T_g of the corresponding alternating dyads. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 1641–1649, 2003     

Synthesis and characterization of well‐defined block and statistical copolymers based on lauryl methacrylate and 2‐(acetoacetoxy)ethyl methacrylate using RAFT‐controlled radical polymerization

Four well‐defined diblock copolymers and one statistical copolymer based on lauryl methacrylate (LauMA) and 2‐(acetoacetoxy)ethyl methacrylate (AEMA) were prepared using reversible addition‐fragmentation chain transfer (RAFT) polymerization. The polymers were characterized in terms of molecular weights, polydispersity indices (ranging between 1.12 and 1.23) and compositions by size exclusion chromatography and ¹H NMR spectroscopy, respectively. The preparation of the block copolymers was accomplished following a two‐step methodology: First, well‐defined LauMA homopolymers were prepared by RAFT using cumyl dithiobenzoate as the chain transfer agent (CTA). Kinetic studies revealed that the polymerization of LauMA followed first‐order kinetics demonstrating the “livingness” of the RAFT process. The pLauMAs were subsequently used as macro‐CTA for the polymerization of AEMA. The glass transition (T_g) and decomposition temperatures (ranging between 200 and 300 °C) of the copolymers were determined using differential scanning calorimetry and thermal gravimetric analysis, respectively. The T_gs of the LauMA homopolymers were found to be around ?53 °C. Block copolymers exhibited two T_gs suggesting microphase separation in the bulk whereas the statistical copolymer presented a single T_g as expected. Furthermore, the micellization behavior of pLauMA‐b‐pAEMA block copolymers was investigated in n‐hexane, a selective solvent for the LauMA block, using dynamic light scattering. pLauMA‐b‐pAEMA block copolymers formed spherical micelles in dilute hexane solutions with hydrodynamic diameters ranging between 30 and 50 nm. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 5442–5451, 2008     

Synthesis,characterization, and micellization of PCL‐g‐PEG copolymers by combination of ROP and “Click” chemistry via “Graft onto” method

Biodegradable and biocompatible PCL‐g‐PEG amphiphilic graft copolymers were prepared by combination of ROP and “click” chemistry via “graft onto” method under mild conditions. First, chloro‐functionalized poly(ε‐caprolactone) (PCL‐Cl) was synthesized by the ring‐opening copolymerization of ε‐caprolactone (CL) and α‐chloro‐ε‐caprolactone (CCL) employing scandium triflate as high‐efficient catalyst with near 100% monomer conversion. Second, the chloro groups of PCL‐Cl were quantitatively converted into azide form by NaN₃. Finally, copper(I)‐catalyzed cycloaddition reaction was carried out between azide‐functionalized PCL (PCL‐N₃) and alkyne‐terminated poly(ethylene glycol) (A‐PEG) to give PCL‐g‐PEG amphiphilic graft copolymers. The composition and the graft architecture of the copolymers were characterized by ¹H NMR, FTIR, and GPC analyses. These amphiphilic graft copolymers could self‐assemble into sphere‐like aggregates in aqueous solution with diverse diameters, which decreased with the increasing of grafting density. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Solid‐state thermal stability and degradation of a family of poly(N‐isopropylacrylamide‐co‐hydroxymethylacrylamide) copolymers

There is widespread interest in responsive polymers that show cloud point behavior, but little attention is paid to their solid state thermal properties. To manufacture products based on such polymers, it may be necessary to subject them to high temperatures; hence, it is important to investigate their thermal behavior. In this study, we characterized a family of poly(N‐isopropylacrylamide‐co‐hydroxymethylacrylamide) copolymers. Although poly(N‐isopropylacrylamide) shows very high thermal stability (up to 360 °C), introduction of hydroxy side chains leads to a significant reduction in stability and new degradation processes become apparent. Thermogravimetric analysis and fourier transform infrared spectroscopy (FT‐IR) indicate that the first degradation process involves a chemical dehydration step (110–240 °C), supported by the nonreversing heat flow response in modulated temperature differential scanning calorimetry. Water loss scales with the fraction of hydroxy monomer in the copolymer. Glass transition temperatures (T_g) are higher than the temperatures causing dehydration; hence, these values relate to newly‐formed copolymer structures produced by controlled heating under nitrogen. Fourier transform‐Raman (FT‐Raman) spectra suggest that this transition involves imine formation. The T_g increases as the fraction of hydroxy groups in the original copolymer increases. Further heating leads to degradation and mass loss, and more complex changes in the FT‐IR spectra, consistent with formation of unsaturated species. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

Radical copolymerization of chlorotrifluoroethylene with 4‐bromo‐3,3,4,4‐tetrafluorobut‐1‐ene

The radical copolymerization of chlorotrifluoroethylene (CTFE) with 3,3,4,4‐tetrafluoro‐4‐bromobut‐1‐ene (BTFB) initiated by tert‐butylperoxypivalate is presented. The microstructures of the obtained copolymers are determined by means of NMR spectroscopies and elemental analysis and show that random copolymers were obtained. A wide range of poly(CTFE‐co‐BTFB) copolymers is synthesized, containing from 17 to 89 mol % of CTFE. In all the cases, CTFE is the less reactive of both comonomers. T_d^10% values, ranging from 163 up to 359 °C, are dependent on the BTFB content. These variations of thermal property are attributed to the increase in the number of C‐H and C‐Br bonds breakdown when the BTFB molar percentage in the copolymer is higher. T_g values range from 19 to 39 °C and a decreasing trend is observed when increasing the amount of BTFB in the copolymer. This observation arises from the higher flexibility of the copolymer when increasing the number of fluorobrominated lateral chains. These original fluoropolymers bearing reactive pendant bromo groups are suitable candidates for various applications. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 1714–1720