Effect of Polycondensation Reaction Conditions on the Properties of Thermotropic Liquid‐Crystalline Copolyester

In this study a range of wholly aromatic copolyesters based on kink m‐acetoxybenzoic acid (m‐ABA) monomer (33 mol%) and equimolar‐linear p‐acetoxybenzoic acid (p‐ABA), hydroquinone diacetate (HQDA) and terephthalic acid (TPA) monomers (67 mol%) have been synthesized by melt polycondensation reaction process at 280°C and 260°C for different time intervals. Characterization of copolyesters were performed by solution viscosity measurement, wide–angle X‐ray diffraction (WAXD), differential scanning calorimetry (DSC), hot‐stage polarized light microscopy, proton‐nuclear magnetic resonance analysis (¹H‐NMR). According to the results obtained, copolyesters showed thermotropic liquid crystalline behavior in an appropriate temperature range. The copolyesters were prepared in high yields. It was observed that the intrinsic viscosities of the copolyesters are increased regularly with increasing polymerization time and temperature. All the copolyesters were soluble in a trifluoroacetic acid/dichloromethane (30:70 v/v) except the copolyesters which were synthesized at 280°C in 5 h. According to the WAXD results; the degree of crystallinity of copolyesters were found to be between 5–15%. DSC and hot stage polarized light microscopy results showed that all the copolyesters are melt processable and a significant molecular interaction exist in a very broad temperature range (160°C and 165°C) in the nematic mesophase. The T_g values are increased with an increasing polycondensation reaction time and temperature and they were observed between 93–126°C. Fibers prepared by a hand‐spinning technique from the polymer melt exhibit well‐developed fibrillar structure parallel to the fiber axis.     

Fully aromatic thermotropic liquid crystalline polyesters of 3-phenyl-4,4′-biphenol with 4,4′-benzophenone dicarboxylic acid

A series of fully aromatic, thermotropic polyesters, derived from 3-phenyl-4,4′-biphenol (MPBP), nonlinear 4,4′-benzophenone dicarboxylic acid (4,4′-BDA), and various other comonomers was prepared by the melt polycondensation method and characterized for their thermotropic liquid crystalline behavior by a variety of experimental techniques. The homopolymer of MPBP with 4,4′-BDA had a fusion temperature (T_f) at 240°C, exhibited a nematic liquid crystalline phase, and had a narrow liquid crystalline range of 60°C. All of the copolyesters of MPBP with 4,4′-BDA and either 30 mol % 4-hydroxybenzoic acid (HBA), 6-hydroxy-2-naphthoic acid (HNA) or 50 mol % terephthalic acid (TA), 2,6-naphthale-nedicarboxylic acid (2,6-NDA) and low T_f values in the range of 210–230°C, exhibited a nematic phase, and had accessible isotropization transitions (T_i) in the range of 320–420°C, respectively. As expected, each of them had a broader range of liquid crystalline phase than the homopolymer. They had a “frozen” nematic, glassy order as determined with the wide-angle X-ray diffraction (WAXD) studies. The morphology of each of the “as-made” polyesters had a fibrous structure as determined with the scanning electron microscopy (SEM), which arises because of the liquid crystalline domains. Moreover, they had higher glass transition temperatures (T_g) in the range of 167–190°C than those of other liquid crystalline polyesters, and excellent thermal stabilities (T_d) in the range of 500–533°C, respectively. © 1995 John Wiley & Sons, Inc.     

Synthesis and characterization of mesogen‐jacketed liquid‐crystal polymers based on 2,5‐bis(4′‐alkoxyphenyl)styrene

A series of novel mesogen‐jacketed liquid‐crystal polymers, poly[2,5‐bis(4′‐alkoxyphenyl)‐styrene] (P‐n, n = 1–11), were prepared via free‐radical polymerization of newly synthesized monomers, 2,5‐bis(4′‐alkoxyphenyl)styrene (M‐n, n = 1–11). The influence of the alkoxy tail length on the liquid‐crystalline behaviors of the monomers and the polymers was investigated with differential scanning calorimetry (DSC), thermogravimetry, polarized optical microscopy (POM), and wide‐angle X‐ray diffraction (WAXD). The monomers with n = 1–4, 9, and 11 were monotropic nematic liquid crystals. All other monomers exhibited enantiotropic nematic properties. Their melting points (T_m's) decreased first as n increased to 6, after which T_m increased slightly at longer spacer lengths. The isotropic–nematic transition temperatures decreased regularly with increasing n values in an odd–even way. The glass‐transition temperatures (T_g's) of the polymers first decreased as the tail lengths increased and then leveled off when n ≥ 7. All polymers were thermally stable and entered the mesophase at a temperature above T_g. Upon further heating, no mesophase‐to‐isotropic melt transition was observed before the polymers decomposed. WAXD studies indicated that an irreversible order–order transition for the polymers with short tails (n ≤ 5) and a reversible order–order transition for those with elongated tails (n ≥ 6) occurred at a temperature much higher than T_g. However, such a transition could not be identified by POM and could be detected by DSC only on heating scans for the polymers with long tails (n ≥ 7). © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 1454–1464, 2003     

The double melting behavior of a liquid crystalline polyimide derived from PMDA and 1,3‐bis[4‐(4′‐aminophenoxyl) cumyl] benzene

The double melting behavior of a thermotropic liquid crystalline polyimide was studied by means of differential scanning calorimetry (DSC), polarized light microscopy (PLM), transmission electron microscopy (TEM), wide‐angle X‐ray diffraction (WAXD), and small‐angle X‐ray scattering (SAXS). This liquid crystalline polyimide exhibited a normal melting peak around 278 °C and transformed into a smectic A phase. The smectic A phase changed to nematic phase upon heating to 298 °C, then became isotropic melt around 345 °C. The samples annealed or isothermally crystallized at lower temperature showed double melting endotherms during heating scan. The annealing‐induced melting endotherm was highly dependent on annealing conditions, whereas the normal melting endotherm was almost not influenced by annealing when the annealing temperature was low. Various possibilities for the lower melting endotherm are discussed. The equilibrium melting points of both melting peaks were extrapolated to be 283.2 °C. Combined analytical results showed that the double melting peaks were from the melting of the two types of crystallites generated from two crystallization processes: a slow and a fast one. Fast crystallization may start from the well‐aligned liquid crystal domains, whereas the slow one may be from the fringed or amorphous regions. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 3018–3031, 2000     

Evolutions of morphology and crystalline ordering upon annealing of quenched isotactic polypropylene

Quenched mesomorphic isotactic polypropylene precursor material has been investigated as well as the material annealed at different temperatures. At room temperature, morphology and crystalline ordering of the materials have been studied by atomic force microscopy (AFM) and wide‐angle X‐ray diffraction (WAXD). The nodular morphology of the mesomorphic precursor remains constant for annealing temperatures T_a below 120 °C. Needle‐like or leaf‐like crystals form when T_a approaches the melting temperature of the precursor. WAXD data analyzed by peak‐fitting indicate that the crystalline ordering along both the chain axis and the lateral directions quickly develops during the mesomorphic‐to‐monoclinic transition, but slowly after the transition (T_a > 140 °C). Combining the AFM and WAXD results it is proposed that two decoupled structure evolution mechanisms are occurring. During the transition, only the crystalline ordering is increasing, but not the size of the nodules. After the transition, the geometry of the nodules changes considerably, whereas there is little additional increase of crystalline ordering. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 1703–1712, 2009     

Synthesis and characterization of a series of wholly aromatic copolyesters containing 2‐(α‐phenylisopropyl)hydroquinone moiety

Two series of new wholly aromatic thermotropic copolyesters containing the 2‐(α‐phenylisopropyl)hydroquinone (PIHQ) moiety have been synthesized and their basic properties such as glass transition temperature (T_g), melting temperature (T_m), thermal stability, crystallinity, and liquid crystallinity were studied by differential scanning calorimetry (DSC), thermogravimetry (TG), and wide‐angle X‐ray diffractometry (WAXD) and on a polarizing microscope. The first series was prepared from acetylated PIHQ, terephthalic acid (TPA), and 2,6‐naphthalenedicarboxylic acid (NDA), and the second series from acetylated PIHQ, TPA, and 1,1′‐biphenyl‐4,4′‐dicarboxylic acid (BDA). The T_g values (152–168°C) of the two series are not much different, although the values for the first series appear slightly higher. The T_m values (287–378°C) and the degree of crystallinity of the first series are appreciably greater than those of the second series. Such differences can be explained by the geometric structure of NDA and BDA moieties. All of the present polyesters are thermotropic and nematic. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 881–889, 1999     

A novel mesogen‐jacketed liquid crystalline electroluminescent polymer with both thiophene and oxadiazole in conjugated side chain

Mesogen‐jacketed liquid crystalline polymers (MJLCPs) with both electron‐transport oxadiazole and hole‐transport thiophene in the side chain were reported for their promising electroluminescent property. Monomers of 2,5‐bis{5‐[(4‐alkoxyphenyl)‐1,3,4‐oxadiazole]thiophen‐2‐yl}styrene (M‐Cm, m is the number of the carbons in the alkoxy groups, m = 8,10) were synthesized and confirmed by ¹H‐NMR, mass spectrometry, and elemental analysis. The corresponding polymers were successfully obtained and characterized by thermal analysis, optical spectroscopy, cyclic voltammetry, electroluminescent analysis, polarized light microscopy (PLM), and wide‐angle X‐ray diffraction (WAXD). The polymers exhibited high decomposition temperatures reaching 382 °C and high T_g's reaching 184 °C. The absorption spectra indicated that both the monomers and polymers had little aggregation in film than that in solution, and the absorption spectra of the polymers showed an obvious blue‐shift compared with those of the monomers. Both the monomers and the polymers had blue‐green emission, and the photoluminescence spectra of the polymers in film suggested the formation of excimer or exciplex. The polymers showed lower HOMO energy levels and LUMO energy levels than those of the MJLCPs containing oxadiazole unit reported before. Electroluminescence study with the device configuration of ITO/PEDOT/PVK/polymer/TPBI/Ca/Ag showed maximum brightness and current efficiency of 541 cd/m² and 0.10 cd/A, which proved that the introduction of directly connected electron‐ and hole‐transport units could greatly improve the EL property of side‐chain conjugated polymers. The phase structures of the polymers were confirmed to be smectic A phase through the results of PLM and WAXD. The annealed samples emitted polarized photoluminescence at room temperature, which indicated potential utility for practical applications in display. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 1502–1515, 2010     

Crystallization and morphology of poly(ethylene oxide‐b‐lactide) crystalline–crystalline diblock copolymers

The crystallization behaviors and morphology of asymmetric crystalline–crystalline diblock copolymers poly(ethylene oxide‐lactide) (PEO‐b‐PLLA) were investigated using differential scanning calorimetry (DSC), wide angle X‐ray diffraction (WAXD), and microscopic techniques (polarized optical microscopy (POM) and atomic force microscopy (AFM)). Both blocks of PEO₅‐b‐PLLA₁₆ can be crystallized, which was confirmed by WAXD, while PEO block in PEO₅‐b‐PLLA₃₀ is difficult to crystallize because of the confinement induced by the high glass transition temperature and crystallization of PLLA block with the microphase separation of the block copolymer. Comparing with the crystallization and morphology of PLLA homopolymer and differences between the two copolymers, we studied the influence of PEO block and microphase separation on the crystallization and morphology of PLLA block. The boundary temperature (T_b) was observed, which distinguishes the crystallization into high‐ and low‐temperature ranges, the growth rate and morphology were quite different between the ranges. Crystalline morphologies including banded spherulite, dendritic crystal, and dense branching in PEO₅‐b‐PLLA₁₆ copolymer were formed. The typical morphology of dendritic crystals including two different sectors were observed in PEO₅‐b‐PLLA₃₀ copolymer, which can be explained by secondary nucleation, chain growth direction, and phase separation between the two blocks during the crystallization process. Lozenge‐shaped crystals of PLLA with screw dislocation were also observed employing AFM, but the crystalline morphology of PEO block was not observed using microscopy techniques because of its small size. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 1400–1411, 2008     

Crystallization kinetics of a thermotropic liquid crystalline polyimide derived from 1,3-bis[4-(4′-aminophenoxy) cumyl] benzene

We have studied the nonisothermal and isothermal crystallization kinetics of an aromatic thermotropic liquid crystalline polyimide synthesized from 1,2,4,5-benzenetetracarboxylic dianhydride (PMDA) and 1,3-bis[4-(4′-aminophenoxy) cumyl] benzene (BACB) by means of differential scanning calorimetry (DSC). Polarized light microscopy (PLM) and wide-angle X-ray diffraction (WAXD) results confirm that this polyimide exhibits a smectic texture. Nonisothermal crystallization showed two strong and one weak exothermic peaks during cooling. The phase transition from isotropic melt to liquid crystalline state is extremely fast which completes in several seconds. The mesophase transition has a small Avrami parameter, n, of approximate 1. The isothermal crystallization of 253–258°C has been examined. The average value n is about 2.6 and the temperature-dependent rate constant k changes about two orders of magnitude in the crystallization temperature range of 6°C. The slope of ln k versus 1/(T_cΔT) is calculated to be −2.4 × 10⁵, which suggests nucleation control, via primary and/or secondary nucleation for the crystallization process. During the annealing process, a new phase (slow transition) is induced, which grows gradually with annealing time. At lower annealing temperatures (220–230°C), the slow transition process seems not to be influenced by the crystals formed during cooling process and its Avrami parameter n is ca. 0.3–0.4. However, the slow transition was hindered by the crystals formed during cooling process when annealed at higher temperature (230–240°C). © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36: 1679–1694, 1998     

Unusual Crystallization Behavior in Nylon‐6 and Nylon‐6/Montmorillonite Nanocomposite Films

Summary: The crystallization behavior of nylon‐6 and nylon‐6/montmorillonite nanocomposite films with different heat histories was investigated by wide‐angle X‐ray diffraction (WAXD). For nylon‐6 films isothermally crystallized above 170 °C or annealed at 200 °C and then quenched in ice water, a crystalline peak appeared at 2θ = 28.5°. This crystalline peak was strong in intensity for the former and weak for the latter. However, for nylon‐6 films cooled in air after isothermal crystallization or annealing, no crystalline peak at 2θ = 28.5° was observed in the WAXD patterns. For nylon‐6/montmorillonite nanocomposite films annealed above 140 °C, a crystalline double peak was observed between the α1 and α2 peaks. The possible origins of the peak at 2θ = 28.5° and the crystalline double peak are discussed.

WAXD patterns of isothermally crystallized nylon‐6/montmorillonite nanocomposite films.     

Melt‐processable poly(oxyphenylalkanoate): Synthesis,properties, and in vitro degradation of poly(4‐oxyphenylacetate)

The homopolyester of 4‐hydroxyphenylacetic acid (HPAA) was synthesized by one‐pot, slurry‐melt, and acidolysis melt polymerization techniques and was characterized by its inherent viscosity and IR and NMR spectra. Differential scanning calorimetry (DSC), polarizing light microscopy (PLM), and wide‐angle X‐ray diffraction (WAXD) studies of the homopolymer were carried out for its thermal and phase behavior. The results indicated that the yield and molecular weight of the polymer depended on the method of preparation; moreover, the acidolysis melt polymerization of the pure acetoxy derivative of HPAA was the best method for the preparation of high molecular weight poly(4‐oxyphenylacetate) (polyHPAA) without side reactions. DSC and PLM studies also showed that the thermal and optical properties depended largely on the polymerization conditions and inherent viscosity values. PolyHPAA did not show a clear texture typical of liquid‐crystalline polymers, whereas after cooling from the melt, structures similar to spherulitic crystals were observed. WAXD patterns showed a crystalline nature. The in vitro degradability of the polymer was also studied via the water absorption in buffer solutions of pH 7 and 10 at 30 and 60 °C; this was followed by Fourier transform infrared, inherent viscosity, DSC, thermogravimetric analysis, WAXD, and scanning electron microscopy techniques. Unlike Vectra®, which showed no degradation, polyHPAA showed an increase in hydrolytic degradation from 5.0 and 6.0% at 30 °C to 12.5 and 15.0% at 60 °C after 350 h in buffer solutions of pH 7 and 10, respectively. The results indicated a possible biomedical prosthetic application of poly(oxyphenylalkanoate)s such as polyHPAA with better crystallinity coupled with degradability as a substitute for poly(hydroxyalkanoates). © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 2430–2443, 2001     

A novel phosphorus‐containing thermotropic liquid crystalline poly(ester‐imide) with high flame retardancy

A novel phosphorus–nitrogen thermotropic liquid crystalline poly(ester‐imide) (PN‐TLCP) derived from p‐acetoxybenzoic acid (ABA), terephthalic acid (TPA), acetylated 2‐(6‐oxide‐6H‐dibenz<c,e><1,2>oxa phosphorin‐ 6‐yl)‐1,4‐dihydroxy phenylene (DOPO‐AHQ) and N,N'‐hexane‐1,6‐diylbis(trimellitimide) was prepared by melt transesterification. The chemical structure, the mesophase behavior, and the thermal properties of the copolymer were investigated with Fourier transform infrared spectroscopy (FTIR), proton nuclear magnetic resonance spectroscopy (¹H NMR), elemental analysis, wide‐angle X‐ray diffraction (WAXD), hot‐stage polarized light microscopy (PLM), differential scanning calorimetry (DSC), and thermogravimetric analysis (TGA). PN‐TLCP exhibited a nematic mesophase with a strong birefringence at a low and broad mesomorphic temperature ranging from 220 to 350°C, an initial flow temperature as low as about 190°C and a glass transition temperature of about 160°C. PN‐TLCP has also good thermal stability, high char residues and excellent flame retardancy (limiting oxygen index, LOI = 71 and UL‐94 V‐0 rating). Copyright © 2009 John Wiley & Sons, Ltd.     

Preparation of oriented β‐form poly(L‐lactic acid) by solid‐state extrusion

Melt‐crystallized, low molecular weight poly(L ‐lactic acid) (PLLA) consisting of α crystals was uniaxially drawn by solid‐state extrusion at an extrusion temperature (T_ext) of 130–170 °C. A series of extrusion‐drawn samples were prepared at an optimum T_ext value of 170 °C, slightly below the melting temperature (T_m) of α crystals (～180 °C). The drawn products were characterized by deformation flow profiles, differential scanning calorimetry (DSC) melting thermograms, wide‐angle X‐ray scattering (WAXD), and small‐angle X‐ray scattering as a function of the extrusion draw ratio (EDR). The deformation mode in the solid‐state extrusion of semicrystalline PLLA was more variable and complex than that in the extensional deformation expected in tensile drawing, which generally gave a mixture of α and β crystals. The deformation profile was extensional at a low EDR and transformed to a parabolic shear pattern at a higher EDR. At a given EDR, the central portion of an extrudate showed extensional deformation and the shear component became progressively more significant, moving from the center to the surface region. The WAXD intensities of the (0010)_α and (003)_β reflections on the meridian as well as the DSC melting thermograms showed that the crystal transformation from the initial α form to the oriented β form proceeded rapidly with increasing EDR at an EDR greater than 4. Furthermore, WAXD showed that the crystal transformation proceeded slightly more rapidly at the sheath region than at the core region. This fact, combined with the deformation profiles (shear at the sheath and extensional at the core), indicated that the crystal transformation was promoted by shear deformation under a high pressure rather than by extensional deformation. Thus, a highly oriented rod consisting of only β crystals was obtained by solid‐state extrusion of melt‐crystallized, low molecular weight PLLA slightly below T_m. The structure and properties of the α‐ and β‐form crystals were also studied. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 40: 95–104, 2002     

Effect of pyridazine structure on thin‐film polymerization and phase behavior of thermotropic liquid crystalline copolyesters

An intensive study has been conducted to compare the effects of malei hydrazine (MH) and hydroquinone (HQ) on the liquid crystallinity and phase transition behavior in the ABA/HQ/TFTA and ABA/MH/TFTA copolyesters (p‐acetoxybenzoic acid (ABA) and tetrafluoroterephthalic acid (TFTA)). These two copolyesters were prepared by thin‐film polymerization and characterized by differential scanning calorimetry (DSC), polarizing light microscope (PLM), wide‐angle X‐ray diffraction (WAXD), as well as Cerius² computational simulation. Characterization and comparison of the liquid crystalline (LC) evolution and morphology changes of HQ moiety with corresponding MH moiety suggest that ABA/MH/TFTA system is energetically favorable to mesophase formation than ABA/HQ/TFTA system. When the films are quenched, a surface microcrack decoration is observed in both systems. Both systems, which have the persistence ratio larger than 6.42, satisfy the minimum requirement for the LC formation by molecular science software. The ABA/MH/TFTA film exhibits only one single peak transition. However, two distinct transitions have been observed in the ABA/HQ/TFTA system. The average Avrami exponent, n, is ～1.2, and PLM and WAXD results suggest mesophase transition in ABA/MH/TFTA film. As reflected by the results obtained from PLM, WAXD, and DSC studies, the phase transition is confirmed as crystal → nematic → isotropic in ABA/HQ/TFTA copolyester. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 2230–2242, 2005     

Synthesis and Characterization of Crystalline Styrene‐b‐(Ethylene‐co‐Butylene)‐b‐Styrene Triblock Copolymers

By merit of dual catalysis of the cationic rare‐earth complex [(η⁵‐Flu‐CH₂‐Py)Ho(CH₂SiMe₃)₂(THF) (Flu = fluorenyl, Py = pyridyl) for the living polymerizations of butadiene (BD) and styrene (St), the crystalline styrene‐butadiene‐styrene (SBS) triblock copolymers consisting of elastic polybutadiene (PBD) sequences with suitable 1,4 regularity (about 70%) and crystalline syndiotactic polystyrene (sPS, [rrrr] > 99%) sequences were successfully synthesized through sequential addition of St, BD, and St monomers. The catalytic system showed high polymerization activities for St and BD in a controlled manner. The crystalline styrene‐b‐(ethylene‐co‐butylene)‐b‐styrene (SEBS) triblock copolymers were obtained by hydrogenation of the above SBS copolymers. The observation of a strong endothermic peak at 266 °C in their differential scanning calorimetry (DSC) curves confirmed the existence of the sPS blocks in the crystalline SEBS different from the industrial product Kraton SEBS‐1652. Thermal degradation temperature of the crystalline SEBS (418 ± 2 °C) indicated the well thermostability and process window of this polymer. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 55, 1243–1249     

Synthesis,characterization, and in vitro degradation of liquid‐crystalline terpolyesters of 4‐hydroxyphenylacetic acid/3‐(4‐hydroxyphenyl)propionic acid with terephthalic acid and 2,6‐naphthalene diol

Melt‐processable liquid‐crystalline terpolyesters of 4‐hydroxyphenylacetic acid (HPAA) and 3‐(4‐hydroxyphenyl)propionic acid (HPPA) with terephthalic acid and 2,6‐naphthalene diol were synthesized by one‐step acidolysis melt polycondensation followed by postpolymerization and were characterized with viscosity studies, Fourier transform infrared (FTIR) and NMR spectroscopy, differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), polarized light microscopy, and wide‐angle X‐ray diffraction. The melting behaviors and liquid‐crystalline transition temperatures of the terpolyesters were dependent on the composition of the HPAA/HPPA content. The transition temperatures of the polyesters could be effectively reduced by the introduction of an even number of built‐in short methylene spacers in combination with the 2,6‐naphthalene offset structure. A terpolyester with an HPPA content of 33% (NTP33) showed optimum properties for the glass‐transition temperature, around 71 °C, and the melting temperature, near 240 °C, with a Schlieren nematic texture. The polymer showed excellent flow behavior in a Brabender plasticorder. It was also thermally stable up to 400 °C. NTP33 showed 2.5% in vitro hydrolytic degradation in buffer solutions of pH 10 at 60 °C after 540 h. Considerable enzymatic degradation was also observed with porcine pancreas lipase/buffer solutions in comparison with Candida rugosa lipase after 60 days. The degradation was also followed with FTIR, DSC, and TGA. Apart from the temperature and pH of the buffer solution, several structural parameters, such as the aromatic content, crystallinity percentage, and composition of the polymer, affected the degradation behavior. FTIR studies indicated the involvement of chain scission during degradation. Scanning electron microscopy studies further showed that surface erosion also played a major role in the degradation. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 1845–1857, 2002     

Synthesis of polyphenylquinoxaline copolymers via aromatic nucleophilic substitution reactions of an A‐B quinoxaline monomer

A self‐polymerizable quinoxaline monomer (A‐B) has been synthesized and polymerized via aromatic nucleophilic substitution reactions. An isomeric mixture of self‐polymerizable quinoxaline monomers—2‐(4‐hydroxyphenyl)‐3‐phenyl‐6‐fluoroquinoxaline and 3‐(4‐hydroxyphenyl)‐2‐phenyl‐6‐fluoroquinoxaline—was polymerized in N‐methyl‐2‐pyrrolidinone (NMP) to afford high molecular weight polyphenylquinoxaline (PPQ) with intrinsic viscosities up to 1.91 dL/g and a glass‐transition temperature (T_g) of 251 °C. A series of comonomers was polymerized with A‐B to form PPQ/polysulfone (PS), PPQ/polyetherether ketone (PEEK), and PPQ/polyethersulfone (PES) copolymers. The copolymers readily obtained high intrinsic viscosities when fluorine was displaced in NMP under reflux. However, single‐electron transfer (SET) side reactions, which limit molecular weight, played a more dominant role when chlorine was displaced instead of fluorine. SET side reactions were minimized in the synthesis of PPQ/PS copolymers through mild polymerization conditions in NMP for longer polymerization times. Thus, the T_g's of PES (T_g = 220 °C), PEEK (T_g = 145 °C), and PS (T_g = 195 °C) were raised through the incorporation of quinoxaline units into the polymer. Copolymers with high intrinsic viscosities resulted in all cases, except in the case of PPQ/PEEK copolymers when 4,4′‐dichlorobenzophenone was the comonomer. © 2001 John Wiley & Sons, Inc. J Polym Sci A Part A: Polym Chem 39: 2037–2042, 2001     

Main‐chain viologen polymers with organic counterions exhibiting thermotropic liquid‐crystalline and fluorescent properties*

A series of viologen polymers with bromide, tosylate, and triflimide as counterions were prepared by either the Menshutkin reaction or metathesis reaction in a common organic solvent. Their polyelectrolyte behavior in methanol was determined by solution viscosity measurements, and their chemical structures were determined by Fourier transform infrared and Fourier transform NMR spectroscopy. They were characterized for their thermotropic liquid‐crystalline properties with a number of experimental techniques. Each of the viologen polymers with organic counterions had a low melting transition or fusion temperature above which it formed either a high‐order smectic phase or a low‐order smectic phase. Each of them also exhibited a smectic‐to‐isotropic transition. The ranges of the liquid‐crystalline phase were 80–88 °C for viologen polymers with tosylate as a counterion and 120–146 °C for viologen polymers with triflimide as a counterion. They had excellent thermal stability. The ranges of thermal stability were 288–329 °C for viologen polymers with tosylate as a counterion and 343–350 °C for viologen polymers with triflimide as a counterion. The fluorescence property for all of the viologen polymers in either aqueous or methanol solution was also included in this study. For example, the viologen polymer containing the 4,4′‐bipyridinium and p‐xylyl units along the backbone of the polymer chain with triflimide as a counterion had an absorption spectrum (λ_max = 265 nm), an excitation spectrum (λ_ex values = 357, 443, and 454 with monitoring at 533 nm), and an emission spectrum (λ_em = 536 nm with excitation at 430 and 450 nm) in methanol. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 659–674, 2002; DOI 10.1002/pola.10134     

SAXS and DSC studies of the crystallization and melting phenomena of poly(ϵ‐caprolactone)

The relationships between the crystallization temperature, T_c, the crystal thickness, d_c and the melting peak temperature, T_m of poly(ϵ‐caprolactone) have been determined by carrying out time‐ and temperature‐dependent small angle x‐ray scattering experiments. A two‐step melting has been suggested, resulting in the occurrence of two well defined independent boundary lines, indicating the transformation from melt into the partially crystalline state. For crystallization temperatures lower than 40°C, during heating, more pronounced peak shifts are observed with the final melting of the crystallites having the same thickness of d_c ≈︁ 7 nm. In this region, it is evident that crystals have relatively good stabilities, since they have fairly uniform thickness. At higher temperatures, above 40°C, T_m increases with T_c, together with the thickness. The transformation of the melt into the partially crystalline state depicts a two‐step process, beginning with the formation of a well defined initial structure with lower order, which is subsequently stabilized.     

Synthesis and thermal behavior of phenylethynyl‐terminated linear and hyperbranched polyphenylquinoxalines

A phenylquinoxaline (PQ) AB monomer mixture was treated with monofunctional and difunctional end‐capping agents and with and without a coupling agent to afford phenylethynyl‐terminated linear PQ oligomers. The resulting PQ oligomers were soluble in common organic solvents and had intrinsic viscosities (IVs) of 0.21–0.30 dL/g. The glass‐transition temperature (T_g) of the diphenylethynyl‐end‐capped PQ oligomer on both sides increased the most, from 215 °C (before curing) to 251 °C (after curing). The PQ AB₂ monomer, which acted as both a coupling agent and a monomer for the hyperbranched polymer, was treated with an AB monomer and end‐capping agents to afford phenylethynyl‐terminated hyperbranched polyphenylquinoxalines (PPQs). They were also soluble in common organic solvents, had IVs of 1.00–1.65 dL/g and T_g's of 251–253 °C, and underwent exothermic cure with maxima around 412–442 °C. The T_g's of the cured hyperbranched PPQs ranged from 258 to 261 °C, depending on the number of phenylethynyl groups on the surface. After further curing, they displayed a T_g of 316 °C in one sample and turned into a fully crosslinked network. The dynamic melt viscosities of a linear oligomer (IV = 0.21 dL/g), a hyperbranched sample (IV = 1.00 dL/g), and a linear reference PPQ (IV = 1.29 dL/g) were compared with respect to the processing temperature. The PQ oligomer and hyperbranched PPQ had low melt viscosities. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 6318–6330, 2004