Thermal Degradation Behavior and Kinetic Analysis of Biodegradable Polymers Using Various Comparative Models, 1

Thermal degradation behavior of a biodegradable polymer (PBS) has been investigated by conventional and MTGA methods. The kinetic parameters of degradation were calculated by a general analytical solution and by the Coats‐Redfern, Ozawa, Horowitz‐Metzger, and MTGA methods. The results reveal that the reaction mechanism at lower temperature is probably the F1 model through the reaction of random chain cleavage via cis‐elimination. However, the reaction mechanism at higher temperature is likely to be D1 model because of the dominant diffusion control effect.

     

Rheology of multi‐walled carbon nanotube/poly(butylene terephthalate) composites

Multi‐walled carbon nanotube/Poly(butylene terephthalate) nanocomposites (PCTs) were prepared by melt compounding. The microstructure of PCTs was investigated using transmission electron micrographs and Fourier transform infra‐red spectrometer. The linear and nonlinear as well as transient rheological properties of PCTs were characterized by the parallel plate rheometer. The results reveal that the surface modification can improve the dispersion state of nanotube in matrix. PCTs present a low percolation threshold of about 1–2 wt % in contrast to that of Poly‐(butylene terephthalate)/clay nanocomposites. The network structure is very sensitive to both the quiescent and large amplitude oscillatory shear deformation, and is also to the temperature, which makes the principle of time‐temperature superposition (TTS) be valid on PCTs only in a very restricted temperature range. The stress overshoots to the reverse flow are strongly dependent on both the rest time and shear rate but show a strain‐scaling response to the startup of steady shear, indicating that the broken network can reorganize even under quiescent condition. The nanotube may experience the long‐range, more or less order during annealing process. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 2239–2251, 2007     

Thermal degradation kinetics of biodegradable poly(3‐hydroxybutyrate)/layered double hydroxide nanocomposites

The thermal degradation behaviors of biodegradable poly(3‐hydroxybutyrate) (PHB) and PHB/poly(ethylene glycol) phosphonates (PEOPAs)‐modified layered double hydroxide (PMLDH) nanocomposites have been investigated using thermogravimetric analysis. Effects of PMLDH contents on the isothermal degradation kinetics of PHB were explored. These experimental results show that the degradation kinetics of PHB/PMLDH nanocomposites is the chain‐scission process of cyclic β‐elimination reaction with the following autocatalytic reactions, which is very similar to that of pure PHB matrix. Further calculated data based on the autocatalytic model can fit very well with the experimental data. The E_a value of PHB/PMLDH nanocomposites is increased as the content of PMLDH increases. This can be attributed to the incorporation of more PMLDH loading to PHB induced a decrease in the degradation rate and an increase in the residual weight for PHB/PMLDH nanocomposites. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 1207–1213, 2008     

Facile Fabrication of PBS/CNTs Nanocomposite Foam for Electromagnetic Interference Shielding

In order to reduce the pollutants of environment and electromagnetic waves, environment friendly polymer foams with outstanding electromagnetic interference shielding are imminently required. In this paper, a kind of electromagnetic shielding, biodegradable nanocomposite foam was fabricated by blending poly (butylene succinate) (PBS) with carbon nanotubes (CNTs) followed by foaming with supercritical CO₂. The crystallization temperature and melting temperature of PBS/CNTs nanocomposites with 4 wt % of CNTs increased remarkably by 6 °C and 3.1 °C compared with that of pure PBS and a double crystal melting peak of various PBS samples appeared in DSC curves. Increasing the CNT content from 0 to 4 wt % leads to an increase of approximately 3 orders of magnitude in storage modulus and nearly 9 orders of magnitude in enhancement of electrical properties. Furthermore, CNTs endowed PBS nanocomposite foam with adjustable electromagnetic interference (EMI) shielding property, giving a specific EMI shielding effectiveness of 28.5 dB cm³/g. This study provides a promising methodology for preparing biodegradable, lightweight PBS/CNTs foam with outstanding electromagnetic shielding properties.     

Kinetics studies on the accelerated curing of liquid crystalline epoxy resin/multiwalled carbon nanotube nanocomposites

A new class of nanocomposite has been fabricated from liquid crystalline (LC) epoxy resin of 4,4′‐bis(2,3‐epoxypropoxy) biphenyl (BP), 4,4′‐diamino‐diphenyl sulfone (DDS), and multiwalled carbon nanotubes (CNTs). The surface of the CNTs was functionalized by LC epoxy resin (ef‐CNT). The ef‐CNT can be blended well with the BP that is further cured with an equivalent of DDS to form nanocomposite. We have studied the curing kinetics of this nanocomposite using isothermal and nonisothermal differential scanning calorimetry (DSC). The dependence of the conversion on time can fit into the autocatalytic model before the vitrification, and then it becomes diffusion control process. The reaction rate increases and the activation energy decreases with increasing concentration of the ef‐CNT. At 10 wt % of ef‐CNT, the activation energy of nanocomposite curing is lowered by about 20% when compared with the neat BP/DDS resin. If the ef‐CNT was replaced by thermal‐insulating TiO₂ nanorods on the same weight basis, the decrease of activation energy was not observed. The result indicates the accelerating effect on the nanocomposite was raised from the high‐thermal conductivity of CNT and aligned LC epoxy resin. However, at ef‐CNT concentration higher than 2 wt %, the accelerating effect of ef‐CNTs also antedates the vitrification and turns the reaction to diffusion control driven. As the molecular motions are limited, the degree of cure is lowered. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2011     

Kinetics study on melt compounding of carbon nanotube/polypropylene nanocomposites

The multiwalled carbon nanotubes/polypropylene nanocomposites (PP/CNTs) were prepared by melt mixing using maleic anhydride grafted polypropylene (mPP) as the compatibilizer. The effect of mPP on dispersion of CNTs was then studied using the tool of rheology, aiming at relating the viscoelastic behaviors to the mesoscopic structure of CNTs. To further explore the kinetics of hybrid formation, a multilayered sample with alternatively superposed neat mPP and binary PP/CNTs microcomposites (without addition of mPP) sheets was prepared and experienced dynamic annealing in the small amplitude oscillatory shear flow. The results show that melt blending CNTs with PP can only yield the composites with microscale dispersion of CNTs, while adding mPP promotes nanoscale dispersion of CNTs as smaller bundles or even as individual nanotubes, reducing percolation threshold as a result. However, the values of apparent diffusivities of the composites are in same order with that of self‐diffusion coefficients of the neat PP, indicating that the presence of detached CNTs nearly does not inhibit PP chain motion. Hence, the activation energy of hybrid formation is close to the self‐diffusion of PP. This also indicates that although addition of mPP can improve the compatibility between CNTs and PP thermodynamically, those dynamic factors, such as shear flow, however, may be the dominant role on hybrid formation. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 608–618, 2009     

Influence of multiwall carbon nanotube on physical properties of poly(ethylene 2,6‐naphthalate) nanocomposites

Polymer nanocomposites consisting of multiwall carbon nanotube (MWCNT) and poly(ethylene 2,6‐naphthalate) (PEN) were prepared by a melt blending process in a twin‐screw extruder. The storage modulus (G′) and loss modulus (G″) of the PEN/MWCNT nanocomposites increased with increasing frequency, and this increment being more significant at low frequency. The terminal zone slope of G′ for the PEN/MWCNT nanocomposites decreased with increasing MWCNT content, and the nonterminal behavior of those was related to the dominant nanotube–nanotube interactions at higher MWCNT content, leading to the formation of the interconnected or network‐like structures of MWCNT in the polymer nanocomposites. The decrease in the slope of the plot of log G′ versus log G″ for the PEN/MWCNT nanocomposites with increasing MWCNT content suggested the changes in the microstructures of the polymer nanocomposites by incorporating MWCNT. The incorporation of very small quantity of MWCNT significantly improved the mechanical properties of the PEN/MWCNT nanocomposites. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 1062–1071, 2006     

Nonisothermal melt crystallization and subsequent melting behavior of biodegradable poly(hydroxybutyrate)/multiwalled carbon nanotubes nanocomposites

In this work, nonisothermal melt crystallization and subsequent melting behavior of poly(hydroxybutyrate) (PHB) and its nanocomposites at different multiwalled carbon nanotubes (MWCNTs) loadings were investigated. Increasing the MWCNTs loadings has enhanced the nonisothermal melt crystallization of PHB significantly in the nanocomposites when compared with that of the neat PHB; furthermore, increasing the cooling rates shift the crystallization exotherms to low temperature range for both neat PHB and its nanocomposites. Double melting behavior is found for both neat PHB and its nanocomposites crystallized nonisothermally from the melt, which is explained by the melting, recrystallization, and remelting model. Effects of the MWCNTs loadings, cooling rates, and heating rates on the subsequent melting behavior of PHB were studied in detail. It is found that increasing the MWCNTs loadings, decreasing the cooling rates, and increasing the heating rates would restrict the occurrence of the recrystallization of PHB in the nanocomposites. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 2238–2246, 2009     

Synthesis,characterization, and thermal degradation mechanism of fast biodegradable PPSu/PCL copolymers

Poly(propylene succinate)/poly(ε‐caprolactone) (PPSu/PCL) 25/75, 50/50, and 75/25 w/w copolymers were prepared using a combination of polycondensation and ring opening polymerization. The randomness of copolymers was characterized using ¹H NMR and ¹³C NMR spectroscopy. From molecular weights and DSC measurements it was observed that the molecular weight decreased with increasing the wt % content of PPSu, while the copolymers containing 50 and 75 wt % PPSu were completely amorphous. Enzymatic hydrolysis revealed that biodegradation rate was much enhanced compared with that of neat PCL and increased by increasing the PPSu content. From TGA analysis it was also found that the PPSu/PCL copolymers had similar thermal decomposition behaviour with the pure polyesters and exhibited their maximum decomposition rates at temperatures 400–420 °C. Two different mechanisms, which follow each other, were used to adequately describe their decomposition kinetics. The first one corresponded to the first stage taking place at 280–365 °C, where small mass loss was recorded and activation energies ranged between 94 and 156 kJ/mol. The second one took place at 370–460 °C and corresponded to the stage where the main polyester mass was decomposed. The activation energies for this stage ranged between 200 and 240 kJ/mol. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 5076–5090, 2007     

Morphology,rheological and crystallization behavior in non-covalently functionalized carbon nanotube reinforced poly(butylene succinate) nanocomposites with low percolation threshold

Multi-walled carbon nanotubes (CNTs) were non-covalently functionalized by surface wrapping of poly(sodium 4-styrenesulfonate) (PSS) with the aid of ultrasound. The functionalized CNTs were incorporated into poly(butylene succinate) (PBS) through solution coagulation to fabricate CNTs filled PBS nanocomposites. The morphologies of the PBS/CNT nanocomposites were studied by scanning electron microscope (SEM) and transmission electron microscope (TEM), and the effect of loading of functionalized CNT on the rheological behavior, electrical conductivity and mechanical properties of the nanocomposites was investigated systemically. SEM observation indicates that functionalized CNTs dispersed in PBS matrix without obvious aggregation and showed good interfacial adhesion with the PBS phase. TEM observation reveals that a CNT network was formed when the loading of CNTs increased from 0.1 to 0.3 wt%. Rheological investigation indicates the formation of a CNT network with a percolation threshold of only 0.3 wt%. Significant improvement in electrical conductivity occurred at CNT loading of 0.3 wt%, with the value of electrical conductivity increasing by six orders of magnitude compared to neat PBS. Differential scanning calorimetry indicates that the melt crystallization temperature of PBS was improved by ∼14 °C with addition of only 0.05 wt% functionalized CNTs. Tensile tests indicate that both the yield strength and Young's modulus of PBS were apparently reinforced by incorporation of functionalized CNTs, while the elongation at break was reduced gradually.     

Zero‐order kinetics of the thermal degradation of polypropylene/clay nanocomposites

The thermal degradation kinetics of polypropylene/clay microcomposites and nanocomposites were studied by thermogravimetric analysis. In comparison with pure polypropylene, the reaction order of the degradation of the composites became zero‐order, and the activation energy increased dramatically. The zero‐order kinetics were associated with the acidic sites (H⁺) created on the clay layers, whereas the increase in the activation energy was coupled with the shielding effect of clay. The kinetic analysis could provide additional mechanistic clues concerning the thermal stability and flammability of polymer/clay nanocomposites. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 3713–3719, 2005     

Fabrication and characterization of poly(butylene succinate)‐grafted carbon fiber/poly(L‐lactide) nanocomposites

A new poly(butylene succinate) (PBS)‐grafted vapor grown carbon fiber (VGCF)/poly(L ‐lactide) (PLLA) nanocomposites were successfully prepared by an in situ condensation reaction between PBS (M_w = 6,000) and surface oxidized VGCF, followed by direct melt mixing technique, and their mechanical and thermal properties were evaluated. Fourier transform infrared spectroscopy and scanning electron microscopy studies indicate a chemical interaction between the PBS and the surface of VGCF. It was found that the maximum tensile strength and modulus of PBS‐grafted VGCF/PLLA nanocomposites were 135 MPa (27% increase relative to neat PLLA) and 4,400 MPa (29% increase relative to neat PLLA), respectively. The results indicate that significant improvement in the mechanical properties can be accomplished by optimizing the surface modification conditions for VGCF. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 4433–4441, 2008     

In situ prepared PBSu/SiO2 nanocomposites. Study of thermal degradation mechanism

A series of nanocomposites consisted of poly(butylene succinate) (PBSu) and fumed silica nanoparticles (SiO₂) were prepared using the in situ polymerization technique. The amount of SiO₂ used directly affected the final molecular weight of the prepared polyesters. At a low SiO₂ content (0.5 wt.%) the molecular weight obtained was higher compared to neat PBSu, however at higher concentrations this was gradually reduced. The melting point of the matrix remained unaffected by the addition of the nanoparticles, in contrast to the crystallinity, which was dramatically reduced at higher SiO₂ contents. This was mainly due to the extended branching and cross-linking reactions that took place between the carboxylic end groups of PBSu and the surface silanols of the nanoparticles. Thermal degradation of the PBSu/SiO₂ nanocomposites was studied by determining theirs mass loss during heating. From the variations of the activation energies, calculated from the thermogravimetric curves, it was clear that nanocomposites containing 1 wt.% SiO₂ content had a higher activation energy compared to pure PBSu, indicating that the addition of the nanoparticles could slightly increase the thermal stability of the matrix. However, in PBSu/SiO₂ nanocomposite containing 5 wt.% SiO₂ the activation energy was smaller. This phenomenon should be attributed to the existence of extended branched and cross-linked macromolecules, which reduce the thermal stability of PBSu, rather than to the addition of fumed silica nanoparticles.     

Effects of comonomer sequential structure on thermal and crystallization behaviors of biodegradable poly(butylene succinate‐co‐butylene terephthalate)s

In this work, new investigations on the effect of comonomer sequential structure on the thermal and crystallization behaviors and biodegradability have been implemented for the biodegradable poly(butylene succinate‐co‐butylene terephthalate) (PBST) as well as aliphatic poly(butylene succinate) (PBS). At first, these copolyesters were efficiently synthesized from dimethyl succinate and/or dimethyl terephthalate and 1,4‐butanediol via condensation polymerization in bulk. Subsequently, their molecular weights and macromolecular chain structures were analyzed by gel permeation chromatography (GPC) and nuclear magnetic resonance (NMR) spectroscopy. By means of differential scanning calorimeter (DSC) and wide‐angle X‐ray diffractometer (WAXD), thermal and crystallization behaviors of these synthesized aromatic–aliphatic copolyesters were further explored. It was demonstrated that the synthesized copolyesters were revealed to have random comonomer sequential structures with thermal and crystallization properties strongly depending on their comonomer molar compositions, and that crystal lattice structures of the new crystallizable copolyesters shifted from the monoclinic crystal of semicrystalline PBS to triclinic lattice of the poly(butylene terephthalate) (PBT) with increasing the terephthalate comonomer composition, and the minor comonomer components were suggested to be trapped in the crystallizable component domains as defects. In addition, the enzymatic degradability was also characterized for the copolyesters film samples. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 1635–1644, 2006     

Dimethyltitanocene-induced surface chemical degradation of synthetic biodegradable polyesters

The purpose of this research was to selectively alter the rate of surface degradation of linear aliphatic polyesters without adversely affecting their bulk properties by way of functional group transformation, where the surface ester linkages would be converted to vinyl ether functionalities with dimethyltitanocene. It has been observed that dimethyl titanocene causes surface degradation of poly (glycolic acid) without adversely affecting its bulk properties, such as M_v, bursting strength, and thermal properties The vinvl ether resulting from the conversion of the PGA ester groups was unstable under ambient conditions, and further reacted by polymer chain scissioning, as was observed from measurements of molecular weight. © 1994 John Wiley & Sons, Inc.     

Thermal behaviors and characteristics of polylactide/poly(butylene succinate) blend films via reactive compatibilization and plasticization

Polylactide (PLA)/poly(butylene succinate) (PBS) blend films modified with a compatibilizer and a plasticizer were hot‐melted through a twin screw extruder and prepared by hydraulic press. Toluene diisocyanate (TDI) and polylactide‐grafted‐maleic anhydride (PLA‐g‐MA) were used as compatibilizers, while triethyl citrate and tricresyl phosphate acted as plasticizers. The effects of the type and content of compatibilizer and plasticizer on the mechanical characteristics, thermal properties, crystallization behavior, and phase morphology of the PLA/PBS blend films were investigated. Reactive compatibilization at increasing levels of TDI improved the compatibility of the PLA and PBS, affecting the toughness of the films. As evidenced by scanning electron microscope, the addition of TDI enhanced the interfacial adhesion of the blends, leading to the appearance of many elongated fibrils at the fracture surface. Furthermore, PLA/PBS blending with both TDI and PLA‐g‐MA led to an acceleration of the cold crystallization rate and an increment of the degree of crystallinity ( ). Toluene diisocyanate could be a more effective compatibilizer than PLA‐g‐MA for PLA/PBS blend films. The synergistic combination of compatibilizer and plasticizer brought a significant improvement in elongation at break and tensile‐impact toughness of the PLA/PBS blends, compared with neat PLA. Their failure mode changed from brittle to ductile due to the improved compatibility and molecular segment mobility of the PLA and PBS phases. Differential scanning calorimeter results revealed that the plasticizers triethyl citrate and tricresyl phosphate changed the thermal behavior of T_cc and T_m, affecting α′ and α crystal formations. However, these plasticizers only slightly improved the thermal stability of the films.     

Investigation of polycarbonate/acrylonitrile butadiene styrene/multiwall carbon nanotube nanocomposites under impact loading

In this study, the effect of polycarbonate (PC)/acrylonitrile butadiene styrene (ABS)‐reinforced multiwall carbon nanotube (MWCNT) nanocomposites under a high‐velocity impact was investigated. PC/ABS (70/30 w/w)/MWCNT nanocomposites containing 1, 2, and 4 wt% were used to manufacture samples for this study. The samples were fabricated in sheet form with 100 × 100 mm dimensions and tested by gas gun for high‐velocity impact tests. The experimental results indicate that the energy absorption, limit velocity, and tensile modulus of the nanocomposite samples increased by approximately 121%, 52%, and 103% for the PC/ABS (70/30 w/w)/2 wt% MWCNT samples respectively. These results were confirmed by a transmission electron microscopy analysis test that was conducted for the state of dispersion of MWCNTs in the nanocomposite samples. The transmission electron microscopy results show that the best morphological structure of carbon nanotube at the interface of PC and ABS is that for the nanocomposite containing 2 wt% MWCNTs, which led to improved interface of the nanocomposites and higher mechanical properties. Copyright © 2016 John Wiley & Sons, Ltd.     

Fabrication and characterization of biodegradable poly(butylene succinate-co-adipate) nanocomposites with halloysite nanotube and organo-montmorillonite as nanofillers

Biodegradable poly(butylene succinate-co-adipate) (PBSA)-based nanocomposites were successfully prepared. A commercial halloysite nanotube (HNT) and an organo-montmorillonite (denoted as 15A) served as reinforcing fillers. Scanning electron microscopy and transmission electron microscopy results confirmed the nano-scale dispersion of HNT and 15A in the composites. Differential scanning calorimetry results showed that 15A served as nucleating agent for PBSA crystallization, but HNT hardly affected the nucleation of PBSA. Both nanofillers assisted the isothermal crystallization of PBSA, with 15A demonstrating superior efficiency. Melting behavior study suggests that the presence of HNT or 15A hampered the melting-recrystallization process of the originally less stable crystals during heating scans. Thermogravimetric analyses revealed that 15A enhanced the thermal stability of PBSA in air environment, but HNT caused a decline at high loadings. The rigidity of PBSA, including Young’s/flexural moduli, evidently increased after the addition of HNT or 15A, with 15A showing higher enhancing efficiency than HNT at similar loadings. The flexural modulus increased up to 94% with 20 wt% in HNT and up to 48% with 5 wt% 15A loading. The rheological property measurements confirmed the achievement of pseudo-network structure at 5 wt% 15A loading, whereas the HNT-included system did not develop a network structure.     

Multifunctional poly(2,5‐benzimidazole)/carbon nanotube composite films

The AB‐monomer, 3,4‐diaminobenzoic acid dihydrochloride, was recrystallized from an aqueous hydrochloric acid solution and used to synthesize high‐molecular‐weight poly(2,5‐benzimidazole) (ABPBI). ABPBI/carbon nanotube (CNT) composites were prepared via in situ polymerization of the AB‐monomer in the presence of single‐walled carbon nanotube (SWCNT) or multiwalled carbon nanotube (MWCNT) in a mildly acidic polyphosphoric acid. The ABPBI/SWCNT and ABPBI/MWCNT composites displayed good solubility in methanesulfonic acid and thus, uniform films could be cast. The morphology of these composite films was studied by X‐ray diffraction, scanning electron microscopy, transmission electron microscopy, and atomic force microscopy. The results showed that both types of CNTs were uniformly dispersed into the ABPBI matrix. Tensile properties of the composite films were significantly improved when compared with ABPBI, and their toughness (～200 MPa) was close to the nature's toughest spider silk (～215 MPa). The electrical conductivities of ABPBI/SWCNT and ABPBI/MWCNT composite films were 9.10 × 10^?5 and 2.53 × 10^?1 S/cm, respectively, whereas that of ABPBI film was 4.81 × 10^?6 S/cm. These values are ～19 and 52,700 times enhanced by the presence of SWCNT and MWCNT, respectively. Finally, without acid impregnation, the ABPBI film was nonconducting while the SWCNT‐ and MWCNT‐based composites were proton conducting with maximum conductivities of 0.018 and 0.017 S/cm, respectively. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 1067–1078, 2010     

New poly(butylene succinate)/layered silicate nanocomposites. II. Effect of organically modified layered silicates on structure,properties, melt rheology,and biodegradability

A series of new poly(butylene succinate) (PBS)/layered silicate nanocomposites were prepared successfully by simple melt extrusion of PBS and organically modified layered silicates (OMLS). Three different types of OMLS were used for the preparation of nanocomposites: two functionalized ammonium salts modified montmorillonite and a phosphonium salt modified saponite. The structure of the nanocomposites in the nanometer scale was characterized with wide-angle X-ray diffraction and transmission electron microscopic observations. With three different types of layered silicates modified with three different types of surfactants, the effect of OMLS in nanocomposites was investigated by focusing on four major aspects: structural analysis, materials properties, melt rheological behavior, and biodegradability. Interestingly, all these nanocomposites exhibited concurrent improvements of material properties when compared with pure PBS. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 3160–3172, 2003