Characterization of resulting network polymer precursors in stepwise crosslinking diepoxide/diamine polymerization

Our previous mechanistic discussion of network formation in chainwise crosslinking multiallyl polymerization was extended to stepwise crosslinking diepoxide/diamine polymerization, typically including bisphenol‐A diglycidyl ether (BADGE) and 4,4′‐diaminodiphenylmethane (DDM). In allyl polymerization a monomer chain transfer is an essential termination reaction, providing only oligomeric primary polymer chains. Therefore, crosslinking multiallyl polymerization could be in the category of a classical gelation theory. Thus, the gelation behavior was discussed by comparing the actual gel point with the theoretical one. Then the resulting network polymer precursors (NPPs) were characterized by size‐exclusion chromatography‐multiangle laser light scattering‐viscometry to clarify the stepwise crosslinking BADGE/DDM polymerization mechanism. Notably, the intrinsic viscosity ratio [η]_NPP/[η]_Linear tended to decrease with the progress of crosslinking and finally, it reached less than 0.2. This suggests that the structure of resulting NPP becomes dendritic at a conversion close to the gel point. These dendritic NPPs can collide with each other to form crosslinks between NPPs, eventually leading to gelation as a reflection of the high concentration of NPP. The dilution effect on gelation was marked in polar solvent; no gelation was observed at a dilution of 1/5. However, in nonpolar solvent the gelation was promoted by dilution; this is ascribed to enhanced crosslink formation between NPPs through hydrogen bonding due to abundant hydroxyl groups in the NPP generated by the polyaddition reaction. Finally, the subject of “Is cured epoxy resin inhomogeneous?” is briefly discussed. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Synthesis and characterization of graft copolymers based on poly(p-phenylene terephthalamide) backbone and well-defined polystyrene side chains

<正>A novel dualfunctional monomer,2-(2',2',6',6'-tetramethyl-piperidinyl-1'-oxy)methylbenzene-1,4-dioyl chloride hydrochloride,with two acid chloride groups for step-growth polymerization and a nitroxide group for the mediation of living radical polymerization was synthesized.It was first copolymerized with terephthaloyl chloride and p-phenylenediamine at a feed molar ratio of 1:3:4 in N-methyl-2-pyrrolidone containing 10 wt%calcium chloride at -10℃to yield a poly(p-phenylene terephthalamide) based macroinitiator,which initiated radical polymerization of styrene at 125℃to obtain a series of poly(p-phenylene terephthalamide)-g-polystyrenes.A combinatory analysis of proton nuclear magnetic resonance spectroscopy,Fourier transform infrared spectroscopy,elementary analysis,thermogravimetry and gel permeation chromatography indicated that the macroinitiator induced the radical polymerization of styrene to proceed in a well-controlled way.The molecular weight of side-chains increased with an increase of monomer conversion,and the molecular weight distribution index remained lower than 1.5.The graft copolymers showed a remarkably improved solubility in N-methyl -2-pyrrolidone and much depressed crystallinity in bulk.     

Design,synthesis, and characterization of a combined main‐chain/side‐chain liquid crystalline polymer based on mesogen‐jacketed liquid crystal polymer via atom transfer radical polymerization

A novel combined main‐chain/side‐chain liquid crystalline polymer based on mesogen‐jacketed liquid crystal polymers (MJLCPs) containing two biphenyls per mesogenic core of MJLCPs main chain, poly(2,5‐bis{[6‐(4‐butoxy‐4′‐oxy‐biphenyl)hexyl]oxycarbonyl}styrene) (P1–P8) was successfully synthesized via atom transfer radical polymerization (ATRP). The chemical structure of the monomer was confirmed by elemental analysis, ¹H NMR, and ¹³C NMR. The molecular characterizations of the polymer with different molecular weights (P1–P8) were performed with ¹H NMR, gel permeation chromatography (GPC), and thermogravimetric analysis (TGA). Their phase transitions and liquid‐crystalline behaviors of the polymers were investigated by differential scanning calorimetry (DSC) and polarized optical microscope (POM). We found that the polymers P1–P8 exhibited similar behavior with three different liquid crystalline phases upon heating to or cooling in addition to isotropic state, which should be related to the complex liquid crystal property of the side‐chain and the main‐chain. Moreover, the transition temperatures of liquid crystalline phases of P1–P8 are found to be dependent on the molecular weight. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 7310–7320, 2008     

Synthesis of PNIPAM polymer brushes on reduced graphene oxide based on click chemistry and RAFT polymerization

Preparation and characterization of poly(N‐isopropylacrylamide) (PNIPAM) polymer brushes on the surfaces of reduced graphene oxide (RGO) sheets based on click chemistry and reversible addition‐fragmentation chain transfer (RAFT) polymerization was reported. RGO sheets prepared by thermal reduction were modified by diazonium salt of propargyl p‐aminobenzoate, and alkyne‐functionalized RGO sheets were obtained. RAFT chain transfer agent (CTA) was grafted to the surfaces of RGO sheets by click reaction. PNIPAM on RGO sheets was prepared by RAFT polymerization. Fourier transform‐infrared spectroscopy, thermogravimetric analysis, X‐ray photoelectron spectroscopy, and transmission electron microscopy (TEM) results all demonstrated that RAFT CTA and PNIPAM were successfully produced on the surfaces of RGO sheets. Nanosized PNIPAM domains on RGO sheets were observed on TEM. Micro‐DSC result indicated that in aqueous solution PNIPAM on RGO sheets presented a lower critical solution temperature at 33.2 °C. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012