Influence of varying hard segments on the properties of chemically crosslinked moisture‐cured polyurethane‐urea

Polyurethane prepolymers are widely used in the reactive hot melt adhesives and moisture‐cured coatings. The chemically crosslinked moisture‐cured formulation based on PEG‐1000 and isophorone diisocyanate was prepared with NCO/OH ratio of 1.6:1.0. Trimethylol propane was used as a crosslinking agent. The excess isocyanate of the prepolymer was chain extended in the ratio of 2:1 (NCO/OH) with different aliphatic diols, and 4:1 with different aromatic diamines. The polymer network maturation during moisture cure was followed by dynamic mechanical thermal analyzer (DMTA) instrument. The thermal and dynamic mechanical properties of the crosslinked polymers were evaluated using thermogravimetric analysis, differential scanning calorimetric analysis and DMTA. Surface properties were evaluated through angle‐resolved X‐ray photoelectron spectroscopy. The present article discusses the physical properties of moisture‐cured polyurethane‐urea (MCPU) containing chemical crosslinks in the hard segment. The complete moisture‐cured polymers showed amorous results toward room temperature modulus, tensile strength, hardness, thermal stability, and transparency. The surface properties showed the enrichment of soft segments. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 102–118, 2006     

Novel AB crosslinked polymer networks from telechelic 4‐vinylbenzyl carbamate terminated polyurethanes and different vinyl monomers

Novel AB crosslinked polymer (ABCP) networks were synthesized from telechelic 4‐vinylbenzyl carbamate terminated polyurethanes and monomers such as styrene, 4‐vinylpyridine, methyl methacrylate and butyl acrylate. Telechelic 4‐vinylbenzyl carbamate terminated polyurethanes were synthesized from polypropylene glycol‐based NCO‐terminated polyurethane and vinylbenzyl alcohol. Effect of changing the molecular weight of polypropylene glycol on the static and dynamic mechanical properties of ABCP networks from polyurethane‐polymethyl methacrylate was studied in detail. Dynamic mechanical thermal analysis results show that polymethyl methacrylate and polystyrene‐based ABCPs have good damping over a broad temperature range. ABCP networks prepared from 4‐vinylbenzyl carbamate terminated polyurethane and different monomers such as methyl methacrylate, butyl acrylate and styrene exhibit single tan δ_max value which implies excellent interlocking between the two polymers present in the ABCP networks. Static mechanical studies showed that methyl methacrylate and styrene‐based ABCP networks exhibit better tensile properties compared to other ABCP networks from butyl acrylate and 4‐vinyl pyridine monomers. Thermogravimetric analysis results revealed that the ABCP networks showed an improved thermal stability. Copyright © 2009 John Wiley & Sons, Ltd.     

Investigation of thermal,mechanical, and electrical properties of novel polyurethanes/high molecular weight polybenzoxazine blends

In order to prepare tough polyurethane (PU) electrical insulator with improved thermal stability and electrical insulating properties, high molecular weight polybenzoxazine precursor was mixed and co‐cured with crosslinkable urethane prepolymers. Polybenzoxazine precursor (Bmda) was synthesized from reaction of bisphenol‐A, methylenedianiline, and paraformaldehyde. Epoxy‐terminated polyurethanes (EPU1‐4) were prepared by the reaction of glycidol with NCO‐terminated urethane oligomers. The oligomers were prepared from different molecular weight versions of polycaprolactone polyol (CAPA) and hexamethylene diisocyanate. Blends were prepared through thermal treatment of equal weights of two precursors dissolved in chloroform. Optimum curing condition was determined by DSC and DMTA analysis and measurement of the gel content for cured samples. Viscoelastic, thermal, mechanical, and electrical properties of cured samples were investigated and structure–property relationship was established. Copyright © 2008 John Wiley & Sons, Ltd.     

Synthesis and characterization of hyperbranched polyesters and polyurethane coatings

Polyurethane (PU) coatings are widely used for variety of high‐performance applications in today's coating technology. The emerging hyperbranched polymers having three‐dimensional morphology have opened a new avenue to tailor the architecture of PU coatings. The methodology followed here is based on preparation of PU coatings from hyperbranched polyester. Initially, different hyperbranched polyester polyols (HPs) were synthesized by varying the hydroxyl‐terminated precursors that is, pentaerythritol, trimethylol propane or glycerol and keeping the diacid that is, adipic acid quantity constant at various mole ratios of 1:0.6, 1:0.8, 1:0.9, and 1:1, respectively. The obtained HPs were characterized by nuclear magnetic resonance (NMR) spectroscopy, matrix‐assisted laser desorption/ionization time‐of‐flight (MALDI‐TOF)‐mass spectrometry, and Fourier transform‐infrared (FTIR) spectroscopy. The degree of branching and the quantity of different structural units present in the various HPs were calculated by integrating the quaternary carbon and carbonyl zone in ¹³C NMR spectroscopy. The extent of condensation in different HPs was also calculated from ¹H NMR spectra. Later on, NCO‐terminated PU prepolymers (NCO‐PU) were synthesized by reacting HPs with isophorone diisocyanate (IPDI) at NCO/OH ratio of 1.6:1. In the third step, the excess NCO content in the NCO‐capped PU prepolymers were reacted with atmospheric moisture and hyperbranched polyurethane (HPU) coatings were formed. The coating films were analyzed by FTIR and dynamic mechanical thermal analysis instruments. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 2673–2688, 2007     

Poly(urethane‐co‐benzoxazine)s via reaction of phenol terminated urethane prepolymers and benzoxazine monomer and investigation of their properties

In the present work, a new method was developed for the combination of polyurethanes (PUs) and polybenzoxazine (PBz) to obtain novel thermoset poly(urethane‐co‐benzoxazine)s with good thermal, mechanical, and electrical properties as well as low temperature curing profile. Knowing the catalytic effect of compounds possessing free phenolic groups on ring opening polymerization of benzoxazine monomers, preparation of phenol terminated urethane oligomers (PTPU) as the macroinitiator for a benzoxazine monomer (Ba) was considered. Firstly, NCO‐terminated urethane prepolymers were prepared from the reaction of poly(tetramethyleneether glycol), and 2,4‐tolylene diisocyanate, and then end functionalized with bisphenol‐A under proper condition. DSC, DMTA, and gel content measurements were applied to find optimum ring opening polymerization condition (170°C for 1 hr and 200°C for 15 min). Various kinds of thermoset polymers were prepared by the reaction of PTPU at different molecular weights with variable contents of Ba. All of monomeric and polymeric materials were characterized by conventional spectroscopic methods and their thermal, mechanical, viscoelastic, and electrical properties were measured and properties were correlated to their structure. Due to the interesting properties of these new materials, the possibility of using them as electrical insulators with higher service temperature in comparison to common PUs were examined and their potential applicability was confirmed. Copyright © 2010 John Wiley & Sons, Ltd.     

Enhancement of the thermal and mechanical properties of a surface‐modified boron nitride–polyurethane composite

Thermoplastic polyurethane (PU) elastomer, prepared from poly(tetramethylene glycol) and methyl diphenyl diisocyanate, was blended with boron nitride (BN) to fabricate a thermally conductive interface material. BN treated by a silane coupling agent (BN―NH₂) and PU‐grafted BN were prepared to fabricate a composite that has better thermal conductivity and mechanical strength. The surface‐modified filler showed enhanced dispersibility and affinity because of the surface treatment with functional groups that affected the surface free energy, along with the structural similarity of the doped crystallized diisocyanate molecule with the matrix. The thermal conductivity increased from 0.349 to 0.467 W mk^?1 on 20 wt% PU‐grafted BN loading that is a 1.34‐fold higher value than in the case of pristine BN loading at the same weight fraction. Moreover, the number of BN particles acting as defects, thereby reducing the mechanical strength, is decreased because of strong adhesion. We can conclude that these composite materials may be promising materials for a significant performance improvement in terms of both the thermal and mechanical properties of PU‐based polymers. Copyright © 2014 John Wiley & Sons, Ltd.     

Effect of NCO/OH ratio and Ce‐Zr nanoparticles on the thermo‐mechanical properties of hyperbranched polyurethane urea coatings

The present study describes the effect of NCO/OH ratio and addition of Cerium (Ce)‐Zirconium (Zr) mixed oxide nanoparticles on the properties of Hyperbranched Polyurethane Urea (HBPUU) Coatings. Initially a hydroxyl terminated hyperbranched polymer (HTBP) was synthesized through A₃ + CB₂ approach. The HTBP and Ce‐Zr nanopowder dispersed HTBP, both were reacted with hexamethylene diisocyanate (HDI) separately; at various NCO/OH eq. ratios to get different NCO terminated HBPU and HBPU/Ce‐Zr hybrid prepolymers. These prepolymers were used for the preparation of HBPUU and HBPUU/Ce‐Zr hybrid coating films through moisture curing. The techniques such as ¹H NMR, ¹³C NMR, FT‐IR, and XRD have been used for structural information while Dynamic mechanical and thermal analyzer (DMTA), Thermogravimetric analysis (TGA) and Universal testing machine (UTM) have been used for evaluation of thermo‐mechanical properties. The combined spectroscopic investigations results indicate the formation of HBPUU network with a degree of branching of 76% while FT‐IR deconvolution results indicates the formation of more hydrogen bonded structure with increasing NCO/OH ratio. The XRD and FT‐IR studies confirm the presence of Ce‐Zr mixed nanoparticles in the HBPUU hybrids. As per TGA and DMTA analysis the thermal stability, char residue, storage modulus (E', material stiffness) and glass transition temperature (T_g), increases with increasing NCO/OH ratio and Ce‐Zr nanoparticle loading in HBPUU coatings. In general, UTM data suggest that the tensile strength increases and per cent elongation at break decreases with increasing the NCO/OH ratio and addition level of nanoparticles in HBPUU coatings. Copyright © 2009 John Wiley & Sons, Ltd.     

Development of biobased polyurethane‐imides from maleinized cottonseed oil and castor oil

An eco‐friendly coating system, which is largely biobased, has been developed from castor and cottonseed oil. Cottonseed oil was functionalized with maleic anhydride by “ene” reaction to give maleinized cottonseed oil (MACSO); the anhydride groups were reacted with isocyanates to yield –NCO terminated polyurethane prepolymer. The prepolymer was further chain extended with hydroxyl groups of castor oil to give polyurethane‐imides (PUIs). The cross‐linked films thus obtained had good mechanical properties, and the imide groups in the backbone improved the corrosion resistance of PUIs as revealed by potentiodynamic polarization study. With increasing content of MACSO, thermal stability, glass transition temperatures (T_g), tensile strength, and corrosion resistance of resulting PUIs significantly increased.     

Antistatic thermoplastic blend of polyaniline and polystyrene prepared in a double-screw extruder

One of the major aims of research on intrinsically conducting polymers (ICP) is the production of blends combining the processing properties of thermoplastic polymers with the conductivity of conducting polymers. The main problem in applying ICP on a large scale in the plastic industry is the impossibility of plasticizing these polymers under heat and shear. However, the use of functionalized acids improves the thermal stability and processability of conductive polymers. In this work the doping process was carried out during processing, also denoted as “reactive processing”. This procedure reduces the number of steps to obtain the final product, PS/SBS/PAni. Blending of polystyrene with dodecylbenzenosulfonic acid doped polyaniline was carried in a double-screw extruder using the block copolymer of styrene and butadiene, SBS, as compatibilizer. A conductive thermoplastic (σ = 10⁻⁶-10⁻² S cm⁻¹) was obtained in the form of ribbons, which were used to evaluate the thermal, mechanical, morphological and electrical properties. We used SBS as compatibilizer and different formulations were tested according to a statistical response surface method. The mechanical and electrical properties of these thermoplastic blends are adequate for antistatic applications.     

Investigations on anticorrosive,thermal, and mechanical properties of conducting polyurethanes with tetraaniline pendent groups

This article describes the synthesis of conducting hybrid polyurethanes from novel tetraaniline‐diol as Gly‐TAni (glycidol with TAni). A new diol Gly‐TAni has been synthesized in a simple process using tetraaniline (TAni) and glycidol via SN2 reaction in a single‐step process. The asymmetric diol (Gly‐TAni) and polyols (PTMEG and TMP) were reacted with isophorone diisocyanate at OH:NCO ratio of 1:1.2 to obtain ―NCO terminated hybrid conducting polyurethanes. These were subjected for curing under atmospheric moisture to obtain conducting polyurethane‐urea coatings. The conducting coatings showed considerable enhancement in thermal and mechanical stabilities. All these conducting coatings films showed excellent corrosion resistance (on mild steel electrode) with an increase in the percentage of Gly‐TANi (5 to 15 wt%). The films of these hybrid polyurethanes containing pendent tetraanilines showed good surface conductivity in the range of 3.69 × 10⁻⁴ to 2.21 × 10⁻³ S/cm. The electrochemical investigation showed 2 single electron oxidation and 2 single reductions reversibly, centred around tetraaniline segments present in the polymer.     

In Situ Reduction of Graphene Oxide in Waterborne Polyurethane Matrix and the Healing Behavior of Nanocomposites by Multiple Ways

Smart polymers are advanced materials that continue to attract scientific community. In this work, self‐healing waterborne polyurethane/reduced graphene oxide (SHWPU/rGO) nanocomposites were prepared by in situ chemical reduction of graphene oxide in a waterborne polyurethane matrix. The chemical structure, morphology, thermal stability, mechanical property, and electrical conductivity of the SHWPU/rGO nanocomposites were characterized. The prepared SHWPU/rGO nanocomposites were further treated under heating, microwave radiating, and electrifying conditions to investigate their healing property. The results showed that chemical reduction of graphene oxide was achieved using hydrazine hydrate as a reducing agent and the rGO was well dispersed in the SHWPU matrix. The thermal stability and mechanical properties of SHWPU/rGO nanocomposites were significantly increased. The SHWPU/rGO nanocomposites can be healed via different methods including heating, microwave radiating, and electrifying. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2019 , 57, 202–209     

High performance UV cured polyurethane dispersion

Imide groups were introduced in the hard segment of UV cured polyurethane dispersion (UV-PUD) by extending the NCO terminated prepolymers with pyromellitic dianhydride (PMDA) where the soft segments were prepared from PTMG, H₁₂MDI, HDI and DMBA. It was found that imide hard segment, as compared with conventional urethane hard segment gave remarkably high mechanical properties as well as thermal stability in terms of decomposition temperature and dynamic mechanical properties at elevated temperatures, and the results were interpreted based on the partial mixing of soft segments and imide hard segments.     

Waterborne polyurethane/NiAl‐LDH/ZnO composites with high antibacterial activity

Novel waterborne polyurethane (WPU) composites based on NiAl‐LDH and ZnO were successfully synthesized by in‐situ polymerization. The nanostructured NiAl‐LDH/ZnO was first grafted by isophorone diisocyanate (IPDI), forming the NiAl‐LDH/ZnO‐NCO complex with ―NCO group on the surface, which promotes its homogeneous dispersion in WPU matrix. The microstructure and particle distribution of the composites were characterized. The mechanical properties and the water resistance of the composites were improved. Furthermore, the composites also exhibit significant antibacterial activity towards G(?) Escherichia coli and G(+) Staphylococcus aureus. Copyright © 2015 John Wiley & Sons, Ltd.     

Synthesis and properties of room temperature curable trimethoxysilane‐terminated polyurethane and their dispersions

The purpose of this research is to study the synthesis and characterization of stable aqueous dispersions of externally chain extended polyurethane/urea compositions terminated by hydrolyzable or hydrolyzed trialkoxysilane groups incorporated through secondary amino groups. These dispersions with excellent storage stability are substantially free from organic solvents which cure to water and solvent resistant, tough, scratch resistant, preferably light stable (non‐yellowing) silylated polyurethane (SPU) films. The films were characterized by FT‐IR, differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), tensile strength and water contact angle measurements, nanoindentation, gel content, water and xylene swellability tests. The properties of the films were discussed and correlated in detail by changing length of soft segment, diisocyanates, NCO/OH ratio and chain extender, ethylenediamine (EDA). From the results, it was found that the particle size and viscosity are lower whereas the gel content and thermal stability are higher for SPUs. Modulus, hardness and tensile properties of SPU films are superior compared to EDA‐PU film. Higher water contact angle and residual weight percentage of SPU films confirm silylation of PU by [3‐(phenylamino)propyl]trimethoxysilane (PAPTMS). Increase in NCO/OH ratios consumes more quantity of PAPTMS which makes PU with superior mechanical properties. Higher PAPTMS content in SPU results in effective crosslinking of the functional silanol groups formed by hydrolysis reaction of trimethoxysilane groups. Overall, SPUs synthesized at 1.4 NCO/OH ratio using Poly‐(oxytetramethylene)glycol (PTMG)‐2000 and isophorone diisocyanate (or) toluene‐2,4‐diisocyanate have excellent properties compared to SPUs prepared using PTMG‐1000 and at 1.2 and 1.6 NCO/OH ratios. SPUs prepared at 1.6 NCO/OH ratio are brittle due to higher crosslinking density. In addition, the crosslinking density of the films can be modified through silane end‐group modification to produce SPUs with a wide range of physical properties. Copyright © 2007 John Wiley & Sons, Ltd.     

Synthesis of head‐to‐tail polyurethanes from nonsymmetric diisocyanate and ethylene glycol with organotin catalysts

An ordered head‐to‐tail (HT) polyurethane was successfully prepared by the polyaddition reaction of p‐isocyanatobenzyl isocyanate with ethylene glycol with dibutyltin dilaurate as a catalyst. Furthermore, the HT regularity of polyurethane was improved to 83% with 1,1,3,3‐tetraphenyl‐1,3‐dichlorodistannoxane. The polymerization was conducted in N,N‐dimethylformamide at 30 °C with both monomers mixed at once. The microstructure of the polymer was investigated by ¹H and ¹³C NMR spectroscopy, and the polymer obtained by the polyaddition reaction had the expected HT linkages. The constitutional regularity of the polymers influenced the thermal properties and crystallinity. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 39: 416–429, 2001     

Polybenzimidazoles tethered with N‐phenyl 1,2,4‐triazole units as polymer electrolytes for fuel cells

Polybenzimidazole (PBI) polymers tethered with N‐phenyl 1,2,4‐triazole (NPT) groups were prepared from a newly synthesized aromatic diacid, 3′‐(4‐phenyl‐4H‐1,2,4‐triazole‐3,5‐diyl) dibenzoic acid (PTDBA). The obtained polymers show superior thermal and chemical stability and good solubility in many aprotic solvents. The inherent viscosities of all polymers were around 1 dL/g. They exhibit high thermal stability with initial decomposition temperature ranging from 515 to 530 °C, high glass transition temperature ranging from 375 to 410 °C, and good mechanical properties with tensile stress in the range of 66–98 MPa and modulus 1897–2600 MPa. XRD analysis indicates that these polymers are amorphous in nature. Physicochemical properties such as water and phosphoric acid‐uptake, oxidative stability, and proton conductivity of membranes of these polymers have also been determined. The proton conductivity ranged from 4.7 × 10^?3 to 1.8 × 10^?2 S cm^?1 at 175 °C in dry conditions. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 2289–2303, 2009     

Studies on photocrosslinking and flame‐retardant properties of chalcone‐based polyacrylamides

A photocrosslinkable polycyclic chalcone‐based acrylamide has been synthesized by Claisen–Schmidt condensation reaction and then polymerized via free radical polymerization technique using azobisisobutyronitrile (AIBN) as an initiator. The resulting polymers have been characterized by FT‐IR, ¹H‐NMR and ¹³C‐NMR analytic techniques. The molecular weights of the polymers were determined by gel permeation chromatography. The thermal properties of synthesized polymers were characterized by TGA analysis, and the obtained results show good thermal and thermo‐oxidative stability which is required for a negative photo resist. The high flame‐retardant properties are calculated from limiting oxygen index (LOI) values and are found to be 36.9 and 32.0 for naphthyl and anthryl chalcone‐based polymers, respectively. The experimentally determined LOI values of polymers (PMNPA and PAPA) are 34.3 and 30.2, respectively, and the values are closer to theoretically found LOI values. However, the cone calorimetry of flame‐retardant PMNPA only showed a slight decrease in peak of heat release rate (PHRR) and total heat release (THR) compared to PAPA but the ignition time (TTI) of PMNPA is slightly higher than PAPA. The photocrosslinking properties of the polymers were investigated by UV spectroscopy technique and were found that with the increase in number of aromatic rings, the rate of crosslinking decreases. Thus polyacrylamides are useful in photolithography technology as well as flame‐retardant property in electrical appliances. Copyright © 2015 John Wiley & Sons, Ltd.     

Synthesis and thermal studies of flexible polyurethane nanocomposite foams obtained using nanoclay modified with flame retardant compound

This work presents thermal studies of nanocomposites based on the flexible polyurethane (PU) matrix and filled using montmorillonite organically modified with organophosphorus flame retardant compound. Flexible PU nanocomposite foams were prepared in the reaction carried out between reactive alcoholic hydroxyl and isocyanate groups with the ratio of NCO to OH groups equal to 1.05. The amount of an organoclay ranging from 3 to 9 vol% was added to the polyol component of the resin before mixing with isocyanate. The apparent density of PU foams was ranging from 0.066 to 0.077 g cm^?1. Thermal properties of the flexible PU nanocomposite foams were investigated by thermogravimetry and dynamical mechanical analysis. Glass transition temperatures (T _g) were defined as maximum peak on tanδ curve. Thermal decomposition was observed at 310–320 °C (calculated from the onset of TG curve). Tensile strength of the PU foams was determined using mechanical test. The microstructure of the nanoparticles and the composites was investigated by X-ray diffraction. Finally, it was confirmed that the thermal and mechanical properties of flexible PU nanocomposite depend on the amount of nanoclay.     

Conducting core‐sheath nanofibers for electroactive shape‐memory applications

Conducting nanofibers coated with polypyrrole (PPy) and poly(3‐hexylthiophene) (P3HT) exhibiting core‐sheath structures were prepared by vapor‐phase polymerization of the conducting polymers on electrospun polyurethane nanofibers. The synthesis of the conducting polymers was confirmed by Fourier transform infrared spectroscopy and energy‐disperse X‐ray spectroscopy. The surfaces of the PPy‐coated nanofibers were slightly rough, while very smooth and regular surfaces were observed in the case of the P3HT‐coated nanofibers. The initial polymerization rate of PPy was higher than that of P3HT. In addition, the electrical conductivities of the core‐sheath structured nanofiber webs of both types increased with polymerization time. The maximum sheet conductivity of the PPy and P3HT‐coated nanofiber webs was 5 × 10^?3 S/cm and 1 × 10^?2 S/cm, respectively. The webs of the conducting core‐sheath structured nanofibers were effective in generating sufficient electrical heating necessary for harnessing these materials for electroactive shape‐memory‐based applications. Copyright © 2013 John Wiley & Sons, Ltd.     

Synthesis and Characterization of Photosensitive Phosphorus Based Polymers Containing α,β‐Unsaturated Ketones in the Main Chain

1,3‐Bis(4‐hydroxyphenyl)propenone (BHPP) and 3‐(4‐hydroxy‐3‐methoxy phenyl)‐1‐(4‐hydroxyphenyl)propenone (HMPHPP) were used as monomers for preparing photosensitive phosphorus containing polyesters. The photosensitive monomers BHPP and HMPHPP were prepared respectively by refluxing 4‐hydroxybenzaldehyde and 3‐methoxy‐4‐hydroxybenzaldehyde with 4‐hydroxy acetophenone. The polyesters were synthesized by interfacial polycondensation of photosensitive diols with N‐phenylphosphoramidic dichloride using hexadecyltrimethyl ammonium bromide (HDTMAB) as phase‐transfer catalyst. Copolymers were also prepared by incorporating terephthaloyl chloride in the polymer backbone. The synthesized monomers and polymers were characterized by UV, FT‐IR and ¹H, ¹³C and ³¹P‐NMR spectroscopic techniques. The resulting polymers had inherent viscosities in the range of 0.15–0.51 dL/g and showed good solubility in polar organic solvents. The thermal properties of the polymers were studied by thermogravimetric analysis and differential scanning calorimetry under nitrogen atmosphere. The TGA data revealed that the 10% weight loss occurs at 275–320°C and all the synthesized polymers showed high char residues. DSC studies indicate that these polymers possess T_g in the range of 48 to 64°C. The photosensitive property of the polymers in film and solution state was investigated by ultraviolet spectroscopy. The effect of incorporation of terephthaloyl unit on photocrosslinking and thermal properties of the polymers was also studied.