Synthesis and Characterization of Novel pH‐Responsive Polyampholyte Microgels

Summary: We synthesized for the first time novel pH‐responsive polyampholyte microgels consisting of poly(methacrylic acid) and poly(2‐(diethylamino)ethyl methacrylate) (PMAA‐PDEA) that are sterically stabilized with poly(ethylene glycol) methyl ether methacrylate (PEGMEM). These microgels showed enhanced hydrophilic behavior in aqueous medium at low and high pH but become hydrophobic and compact between pH 4 and 6 near the isoelectric point. Dynamic‐light scattering measurements showed that the hydrodynamic radius, R_h of these microgels is approximately 100 nm between pH 4 and 6 and increases to around 140 and 170 nm at pH 2 and 10, respectively. It is evident that the cross‐linked MAA‐DEA microgel that is sterically stabilized with PEGMEM retains the polyampholyte properties in solution.

Sterically stabilized cross‐linked MAA‐DEA microgel.     

Novel pH‐ and Temperature‐Responsive Block Copolymers with Tunable pH‐Responsive Range

A series of novel pH‐ and temperature‐responsive diblock copolymers composed of poly(N‐isopropylacrylamide) (PNIPAM) and poly[(L ‐glutamic acid)‐co‐(γ‐benzyl L ‐glutamate)] [P(GA‐co‐BLG)] were prepared. The influence of hydrophobic benzyl groups on the phase transition of the copolymers was studied for the first time. With increasing BLG content in P(GA‐co‐BLG) block, the thermal phase transition of the diblock copolymer became sharper at a designated pH and the critical curve of phase diagram of the diblock copolymer shifted to a higher pH region. Notably, when the BLG content in P(GA‐co‐BLG) block was more than 30 mol.‐%, the diblock copolymer responded sharply to a narrow pH change in the region of pH 7.4–5.5.

     

A novel pH‐ and thermo‐sensitive PVP/CMC semi‐IPN hydrogel: Swelling,phase behavior,and drug release study

Poly(N‐vinyl‐pyrrolidone) (PVP) hydrogel has been considered as a very interesting and promising thermosensitive material. The most vital shortcoming of PVP hydrogel as thermosensitive material is that it does not exhibit thermosensitivity under usual conditions. In this work, semi‐interpenetrating polymer network (semi‐IPN) hydrogels based on PVP and carboxymethylcellulose (CMC) were prepared. The volume phase transition temperature (VPTT) of the hydrogels was determined by swelling behavior and differential scanning calorimetry (DSC). The results showed that the VPTT was significantly dependent on CMC content and the pH of the swelling medium. The amount of CMC in the semi‐IPN hydrogels was 0.050, 0.075, and 0.100 g, the VPTT in buffer solution of pH 1.2 was 29.9 °C, 27.5 °C and 24.5 °C, respectively. In addition, the VPTT occurred in buffer solution of pH 1.2, but did not appear in alkaline medium. Bovine serum albumin (BSA) as a model drug was loaded and the in vitro release studies were carried out in different buffer solutions and at different temperatures. The results of this study suggest that PVP/CMC semi‐IPN hydrogels could serve as potential candidates for protein drug delivery in the intestine. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 1749–1756, 2010     

Synthesis and Characterization of pH‐sensitive Poly(IA‐co‐AAc‐co‐AAm) Hydrogels via Frontal Polymerization

In this work, we report a series of poly(itaconic acid‐co‐acrylic acid‐co‐acrylamide) (poly(IA‐co‐AAc‐co‐AAm)) hydrogels via frontal polymerization (FP). FP starts on the top of the reaction mixture with aid of heating provided from soldering iron gun. Once polymerization initiated, no further energy is required to complete the process. The influences of IA/AAc weight ratios on frontal velocities, temperatures, and conversions on the reaction time are thoroughly investigated and discussed where the amount of AAm monomer remains constant. Fourier transform‐infrared spectroscopy (FTIR), differential scanning calorimetry (DSC), scanning electron microscope (SEM), dynamic mechanical analysis, and the swelling measurement are applied to characterize the as‐synthesized poly(IA‐co‐AAc‐co‐AAm) hydrogels. Interestingly, the swelling ratios of the hydrogels are changed with different IA/AAc contents, and the maximum swelling ratios are ~4439% in water. SEM images describe highly porous morphologies and explain good swelling capabilities. Moreover, the poly(IA‐co‐AAc‐co‐AAm) hydrogels exhibit superior pH‐responsive ability. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019 , 57, 2214–2221     

Facile synthesis of pH‐responsive glycopolypeptides with adjustable sugar density

Well‐defined pH‐responsive glycopolypeptides were prepared by polymer‐analogous aqueous amide coupling of d ‐glucosamine to poly(α,l ‐glutamic acid) (PGA) using the coupling agent 4‐(4,6‐dimethoxy‐1,3,5‐triazin‐2‐yl)‐4‐methylmorpholinium chloride (DMT‐MM) without any organic solvents, additives, or buffers. Degrees of substitution (DS) up to 80% can be achieved, and the DS is adjustable by the molar ratio of DMT‐MM to PGA repeating units. Successful glycosylation of both low MW and high MW PGA was confirmed by ¹H NMR and FTIR spectroscopy as well as by an enhanced solubility at low pH. CD spectroscopy revealed that glycosylated PGAs with a DS up to 0.63 are able to undergo a pH‐responsive and reversible helix‐coil transition. However, for polymers with higher DS no transition occurs. A comparison with PGAs functionalized with monoethanolamine showed that the low helicity at high DS is not a steric effect due to the bulky sugar moieties, but a solvation effect. Preliminary turbidimetric tests with the lectin Concanavalin A indicate a biological activity of these glycosylated polypeptides. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013 , 51, 3925–3931     

Synthesis of pH‐ and thermoresponsive poly(2‐n‐propyl‐2‐oxazoline) based copolymers

Polymers that possess lower critical solution temperature behavior such as poly(2‐alkyl‐2‐oxazoline)s (PAOx) are interesting for their application as stimulus‐responsive materials, for example in the biomedical field. In this work, we discuss the scalable and controlled synthesis of a library of pH‐ and temperature‐sensitive 2‐n‐propyl‐2‐oxazoline P(nPropOx) based copolymers containing amine and carboxylic acid functionalized side chains by cationic ring opening polymerization and postpolymerization functionalization strategies. Using turbidimetry, we found that the cloud point temperature (CP) is strongly dependent on both the polymer concentration and the polymer charge (as a function of pH). Furthermore, we observed that the CP decreased with increasing salt concentration, whereas the CP increased linearly with increasing amount of carboxylic acid groups. Finally, turbidimetry studies in PBS‐buffer indicate that CPs of these polymers are close to body temperature at biologically relevant polymer concentrations, which demonstrates the potential of P(nPropOx) as stimulus‐responsive polymeric systems in, for example, drug delivery applications. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 1573–1582     

pH‐responsive photoluminescence properties of a water‐soluble copolymer containing quinoline groups in aqueous solution

The synthesis of a water‐soluble copolymer containing quinoline groups, P(DMAM‐co‐SDPQ), through free radical copolymerization of N,N‐dimethylacrylamide, DMAM, with 2,4‐diphenyl‐6‐(4‐vinylphenyl)quinoline, SDPQ, is presented and the optical properties of the final product are investigated in aqueous solution as a function of pH. It is found that the emission peak of SDPQ is red‐shifted from 411 to 484 nm with decreasing pH, due to the protonation of quinoline groups at low pH, suggesting that this copolymer may function as a luminescent pH‐indicator. Moreover, the copolymer exhibits the characteristics of a luminescent pH‐detector within the pH range 2 < pH < 4, as in this pH region the ratio of the emission intensity at 411 nm over that at 484 nm changes linearly in a logarithmic scale with the pH of the solution. Finally, the formation of less polar quinoline clusters in the aqueous P(DMAM‐co‐SDPQ) solution upon increasing pH was detected through Nile red probing. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 2078–2083, 2010     

Synthesis and properties of chitosan‐based thermo‐ and pH‐responsive nanoparticles and application in drug release

In this research, thermo‐ and pH‐responsive nanoparticles with an average diameter of about 50–200 nm were synthesized via the surfactant‐free emulsion polymerization. The thermal/pH dual responsive properties of these nanoparticles were designed by the addition of a pH sensitive monomer, acrylic acid (AA), to be copolymerized with N‐isopropylacrylamide (NIPAAm) in a chitosan (CS) solution. The molar ratio of CS/AA/NIPAAm in the feed was changed to investigate its effect on structure, morphology, thermal‐ and pH‐responsive properties of the nanoparticles. It was found that CS‐PAA‐PNIPAAm nanoparticles could be well dispersed in the aqueous solution and carried positive charges on the surface. The addition of thermal‐sensitive NIPAAm monomer affected the polymerization mechanism and interactions between CS and AA. The particle size of the nanoparticles was found to be varied with the composition of NIPAAm monomer in the feed. The synthesized nanoparticles exhibited stimuli‐responsive properties, and their mean diameter thus could be manipulated by changing pH value and temperature of the environment. The nanoparticles showed a continuous release of the encapsulated doxycycline hyclate up to 10 days during an in vitro release experiment. The environmentally responsive nanoparticles are expected to be used in many fields such as drug delivery system. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 2798–2810, 2009     

Terminal Modification with 1‐Adamantylamine to Endow Hyperbranched Polyamidoamine with Thermo‐/pH‐Responsive Properties

A novel terminal modification agent to endow hyperbranched polyamidoamine (HPAMAM) with thermo‐/pH‐responsive properties is reported. HPAMAM with terminal vinyl groups is first synthesized and then end‐capped by 1‐adamantylamine (ADA). The resulting hyperbranched polymer (HPAMAM‐ADA) shows interesting thermo‐responsive properties in aqueous solution, which have been investigated by UV‐vis spectroscopy, optical microscopy, and ¹H NMR spectroscopy. The lower critical solution temperature can be controlled by adjusting the end‐capping ratio of ADA. In addition, HPAMAM‐ADA exhibits a pH‐dependent water solubility. This pH‐responsive behavior is also studied.

     

Synthesis and UCST‐type phase behavior of polypeptide with alkyl side‐chains in alcohol or ethanol/water solvent mixtures

A series of thermoresponsive polypeptides bearing 1‐butyl, 1‐hexyl, or 1‐dodecyl side‐chains (i.e., 6a ‐ 6c ) were synthesized by copper‐mediated 1,3‐dipolar cycloaddition with high grafting efficiency (>95%) between side‐chain “clickable” polypeptide, namely poly(γ‐4‐(propargoxycarbonyl)benzyl‐_L‐glutamate) ( 5 ) and 1‐azidoalkanes. 5 with different degree of polymerization (DP = 48–86) were prepared from triethylamine initiated ring‐opening polymerization of γ‐4‐(propargoxycarbonyl)benzyl‐_L‐glutamic acid based N‐carboxyanhydride ( 4 ). ¹H NMR, FTIR, and GPC results revealed the successful preparation of the resulting polypeptides. 6a ‐ 6c showed reversible UCST‐type phase behaviors in methanol, ethanol, and ethanol/water solvent mixtures depending on the polymer main‐chain length, alkyl side‐chain length, weight percentage of ethanol (f_w) in the binary solvent, and so forth. FTIR analysis revealed the presence of the van der Waals interaction between the alkyl pendants of polypeptides and alkyl groups of alcoholic solvents. Variable‐temperature UV‐vis spectroscopy revealed that the UCST‐type phase transition temperature (T_pt) increased as polymer main‐chain length or concentration increased. In ethanol/water solvent mixtures, polypeptide with short alkyl pendant (i.e., 1‐butyl group) and short main‐chain length (DP = 41) showed the widest f_w range and T_pts in the range of 61.0–71.1 °C. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 3425–3435     

Stimuli‐Responsive A‐b‐(B‐co‐C) Diblock Terpolymers Bearing Polyampholyte Sequences

Summary: Diblock terpolymers that consist of homopolymer and statistical copolymer (polyampholyte) building blocks are synthesized by group transfer polymerization. Two types of block tepolymers are explored in aqueous media: the amphiphilic poly{[(diethylamino)ethyl methacrylate]‐co‐(methacrylic acid)}‐block‐poly(methyl methacrylate) and the double hydrophilic poly[oligo(ethylene glycol) methacrylate]‐block‐poly{[(diethylamino)ethyl methacrylate]‐co‐(methacrylic acid)}. The first terpolymer self‐assembles in aqueous media to form responsive micelles that change their corona charge sign upon switching pH. The second terpolymer exhibits a multi‐responsive behavior. It forms neutral, positive, or negative micelles depending on a combination of different environmental conditions such as temperature, pH, and ionic strength.

P(DEAEMA‐co‐MAA)‐b‐PMMA pH‐sensitive micelles.     

Dual Thermo‐ and pH‐Responsive Zwitterionic Sulfobataine Copolymers for Oral Delivery System

A novel oral delivery system consisting of thermoresponsive zwitterionic poly(sulfobetaine methacrylate) (PSBMA) and pH‐responsive poly(2‐(diisopropylamino)ethyl methacrylate) (PDPA) is synthesized via free radical polymerization. This copolymer can self‐aggregate into nanoparticles via electrostatic attraction between ammonium cation and sulfo‐anion of PSBMA and successfully encapsulate anticancer drug, curcumin (CUR), with highest loading content of 2.6% in the P(SBMA‐co‐DPA) nanoparticles. The stimuli‐responsive phase transition behaviors of P(SBMA‐co‐DPA) copolymers at different pH buffer solution show pH‐dependent upper critical solution temperature (UCST) attributed to the influence of protonation/deprotonation of the pH‐responsive DPA segments. Through the delicate adjustment of the PSBMA/PDPA molar ratios, the stimuli‐responsive phase transition could be suitable for physiological environment. The kinetic drug release profiles demonstrate that P(SBMA‐co‐DPA) nanoparticles have the potential as oral delivery carriers due to their effective release of entrapped drugs in the stimulated intestinal fluid and preventing the deterioration of drug in stimulated gastric fluid.

     

Catch and Release of DNA in Coacervate‐Dispersed Gels

Summary: We have synthesized novel coacervate‐droplet gels, which were applied to controlling the transportation of DNA in electrophoresis. Coacervate droplets are colloidal particles and they are usually composed of positive and negative polyelectrolytes. However, the polyzwitterion (polyampholyte) PDMAPS can form coacervate droplets in water by itself, since PDMAPS has both positive and negative charges in each side group of main chain. Coacervate droplets have a unique nature and can catch charged macromolecules such as DNA. In order to utilize the nature of the PDMAPS coacervate droplets for the catch and release of DNA, we stabilized PDMAPS droplets in gels. The droplets catch the DNA in electrophoresis and the release of DNA can be controlled by temperature and salt addition.

Electrophoresis of DNA, using coacervate‐dispersed PAAm gels, prepared at various PDMAPS concentrations. The circles indicate the PAAm gels embedded in agarose gels.     

Gold Nanoparticles Functionalized by a Dextran‐Based pH‐ and Temperature‐Sensitive Polymer

A dextran‐based dual‐sensitive polymer is employed to endow gold nanoparticles with stability and pH‐ and temperature‐sensitivity. The dual‐sensitive polymer is prepared by RAFT polymerization of N‐isopropylacrylamide from trithiocarbonate groups linked to dextran and succinoylation of dextran after polymerization. The functionalized nanoparticles show excellent stability under various conditions and can be stored in powder‐form. UV and DLS measurements confirm that the temperature‐induced optical changes and aggregation behaviors of the particles are strongly dependent on pH.

     

Redox‐ and pH‐Responsive Cysteamine‐Modified Poly(aspartic acid) Showing a Reversible Sol–Gel Transition

Synthesis and characterization of a pH‐ and redox‐sensitive hydrogel of poly(aspartic acid) are reported. Reversible gelation and dissolution are achieved both in dimethylformamide and in aqueous medium via a thiol‐disulphide interconversion in the side chain of the polymers. Structural changes are confirmed by Raman microscopy and rheological measurements. Injectable aqueous solutions of thiolated poly(aspartic acid) can be converted into mechanically stable gels by oxidation, which can be useful for drug encapsulation and targeted delivery. Reduction‐facilitated release of an entrapped drug from disulphide cross‐linked hydrogels is studied.

     

pH‐ and β‐cyclodextrin‐responsive micelles based on polyaspartamide derivatives as drug carrier

A novel kind of graft polymer poly(aspartic acid)‐ethanediamine‐g‐adamantane/methyloxy polyethylene glycol (Pasp‐EDA‐g‐Ad/mPEG) was designed and synthesized for drug delivery in this study. The chemical structure of the prepared polymer was confirmed by proton NMR. The obtained polymer can self‐assemble into micelles which were stable under a physiological environment and displayed pH‐ and β‐cyclodextrin (β‐CD)‐responsive behaviors because of the acid‐labile benzoic imine linkage and hydrophobic adamantine groups in the side chains of the polymer. The doxorubicin (Dox)‐loaded micelles showed a slow release under physiological conditions and a rapid release after exposure to weakly acidic or β‐CD environment. The in vitro cytotoxicity results suggested that the polymer was good at biocompatibility and could remain Dox biologically active. Hence, the Pasp‐EDA‐g‐Ad/mPEG micelles may be applied as promising controlled drug delivery system for hydrophobic antitumor drugs. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 1387–1395     

Layer‐by‐layer assembly of gelatin

Electrostatic assembly of one species can be realized using gelatin as a polyampholyte. Under suitable conditions where the electrostatic attraction and repulsion were both significant and in balance, linear growth of multilayers driven by electrostatic interactions was sustained over many successive assembly steps, and the maximum amount of adsorption of each layer was reached when the solution pH was around the isoelectric point. The rearrangement of the adsorbed chains after drying was confirmed by contact angle analysis. In addition with only one species involved, the assembled thin films should be chemically uniform rather than layered. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 1252–1257, 2008     

Meshless simulation of equilibrium swelling/deswelling of pH‐sensitive hydrogels

Hydrogels have been widely used in microelectromechanical systems (MEMS) and Bio‐MEMS devices. In this article, the equilibrium swelling/deswelling of the pH‐stimulus cylindrical hydrogel in the microchannel is studied and simulated by the meshless method. The multi‐field coupling model, called multi‐effect‐coupling pH‐stimulus (MECpH) model, is presented and used to describe the chemical field, electric field, and the mechanical field involved in the problem. The partial differential equations (PDEs) describing these three fields are either nonlinear or coupled together. This multi‐field coupling and high nonlinear characteristics produce difficulties for the conventional numerical methods (e.g., the finite element method or the finite difference method), so an alternative—meshless method is developed to discretize the PDEs, and the efficient iteration technique is adopted to solve the nonlinear problem. The computational results for the swelling/deswelling diameter of the hydrogel under the different pH values are firstly compared with experimental results, and they have a good agreement. The influences of other parameters on the mechanical properties of the hydrogel are also investigated in detail. It is shown that the multi‐field coupling model and the developed meshless method are efficient, stable, and accurate for simulation of the properties of the stimuli‐sensitive hydrogel. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 326–337, 2006