Mesoporous hollow silica spheres as micro-water-tanks in proton exchange membranes

In order to decrease the swelling of Nafion^® and reduce the dependency of proton conductivity on high relative humidity (RH), mesoporous hollow silica spheres were synthesized and dispersed in Nafion matrix as micro-water-tanks in the proton exchange membranes (PEM). The morphologies of MHSi and Nafion/MHSi composite membranes are characterized by SEM and TEM. The effects of MHSi on water uptake, swelling, dehydration rate and proton conductivity of the composite membranes were investigated. The results show that, with a suitable portion of MHSi in the membrane, composite PEMs with enhanced water uptake, reduced swelling and improved proton conductivity are obtained.     

Preparation and properties of Nafion/hollow silica spheres composite membranes

In present work, hollow silica spheres (HSS)/Nafion^® composite membranes were prepared by solution casting. The thermal properties, water retention, swelling behavior and proton conductivity of the composite membranes were explored. It was found that HSS dispersed well at micrometer scale in the obtained composite membranes by SEM and TEM observation. Thermal properties of composite membranes were improved than that of recast Nafion^® membrane. Compared with the recast Nafion^® membrane, the composite membranes showed higher water uptake and lower swelling degree at the temperature range from 40 to 100 °C. At the same HSS loading, the smaller the diameter of HSS in composite membranes, the more the water uptake, however, the swelling degree of composite membranes was increased. The proton conductivity of the composite membrane with 3–5 wt.% HSS (120 and 250 nm) increased distinctively at above 60 °C, reached the optimal value at 100 °C, and decreased slowly when the temperature exceeded 100 °C.     

Preparation of epoxy‐functionalized polystyrene/silica core–shell composite nanoparticles

Epoxy‐functionalized polystyrene/silica core–shell composite nanoparticles were prepared by the postaddition of glycidyl methacrylate (GMA) via emulsion polymerization. The outermost shell of obtained multilayered core–shell particles was made up of poly(glycidyl methacrylate) (PGMA). A semicontinuous process involving the dropwise addition of GMA was used to avoid demulsification of the emulsion system. The amount of grafted PGMA was quantified by Fourier transform infrared spectroscopy and was altered in a wide range (1–50 wt % to styrene). The binding efficiency was usually high (ca. 90%), indicating strong adhesion between the silica core and the polymer shell. There were approximately four or five original silica beads, which formed a cluster, per composite of nanoparticles whose size was about 60–70 nm. Other main factors of polymerization conditions including the amounts of sodium dodecyl sulfonate and silica are also discussed. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 2253–2262, 2004     

Synthesis and characterization of benzimidazolium‐functionalized polysulfones as anion‐exchange membranes

Anion‐exchange membranes containing pendant benzimidazolium groups were synthesized from polysulfone by chrolomethylation followed by nucleophilic substitution reaction with 1‐methylbenzimidazole. The structures of the polymers were characterized by ¹H‐NMR and FTIR analysis. The resulting membranes showed high thermal stability below 200 °C. The values of water uptake and swelling degree increased with the ion‐exchange capacity of the polymeric membrane. The ionic conductivity was measured by means of impedance spectroscopy in aqueous solution of potassium hydroxide (10^?4?10^?1 M). The results show not only a clear correlation between the membrane's electrochemical behavior with the electrolyte solution embedded in the membrane, but also with the degree of the polysulfone's chloromethylation.Thus, the ionic conductivity increased more than two orders of magnitude when the degree of chloromethylation increased from 40 to 140%. Benzimidazolium‐functionalized polysulfones exhibited better thermal, mechanical, and electrochemical properties than the widely used polymeric membranes containing quaternary ammonium groups. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 2363–2373     

Characterization,morphology, thermal and mechanical properties of conductive polyaniline‐functionalized EPDM elastomers obtained by casting

Conductive elastomeric blends based on ethylene–propylene–5‐ethylidene–2‐norbornene terpolymer (EPDM) and polyaniline doped with 4‐dodecylbenzenesulfonic acid [PAni(DBSA)] were cast from organic solvents. Functionalization of the elastomer was promoted by grafting with maleic anhydride. Vulcanization conditions were optimized with an oscillating disk rheometer. The conductivity, morphology, thermal stability, compatibility, and mechanical behavior of the obtained mixtures were analyzed by in situ direct current conductivity measurements, atomic force microscopy, transmission electron microscopy, wide‐angle X‐ray scattering, thermogravimetric analysis, differential scanning calorimetry, dynamic mechanical thermal analysis, stress–strain and hysteresis tests. The vulcanization process was affected by temperature, the PAni content, and maleic anhydride. A reinforcement effect was promoted by the vulcanizing agent. The formation of links between the high‐molar‐mass phases and oligomers of PAni(DBSA) in the elastomeric matrix enhanced the thermal stability and ultimate properties of the blends. By the appropriate control of the polymer blends' composition, it was possible to produce elastomeric materials with conductivities in the range of 10^?5–10^?4 S · cm^?1 and excellent mechanical properties. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1767–1782, 2004     

Nanocomposites of Polyaniline/Poly(2‐methoxyaniline‐5‐sulfonic acid)

Summary: Poly(2‐methoxyaniline‐5‐sulfonic acid) (PMAS) is a water‐soluble derivative of polyaniline that carries negatively charged sulfonate groups. This self‐doped conducting polymer also behaves like a polyelectrolyte that can subsequently function as a dopant in polyaniline (PAn). The chemical synthesis of PAn/PMAS is presented describing the preparation of a highly stable composite dispersion. TEM images reveal a mixture of well‐defined nanofibres and nanoparticles with diameters between 20 and 100 nm. The UV‐vis spectra of the PAn/PMAS composite in water and in alkaline media indicate that both PAn and PMAS are present in the composite. Electrochemical studies show that both of the conducting polymer components are capable of undergoing oxidation and reduction. The novel PAn/PMAS nanocomposite has enhanced electrical conductivity and stability compared to PAn/HCl nanofibres prepared under equivalent conditions, making it a promising material for applications in areas such as batteries, electronic textiles, electrochromics, and chemical sensors.

Transmission electron micrograph of a PAn/PMAS nanocomposite.     

Synthesis and proton conductivity studies of polystyrene‐based triazole functional polymer membranes

In this study, poly(vinylbenzylchloride) (PVBC) was produced by free‐radical polymerization of 4‐vinylbenzylchloride, and then it was functionalized with 3‐amino‐1,2,4‐triazole (ATri) and 1H‐1,2,4‐triazole (Tri). The composition of the polymers was verified by elemental analysis, and the structure was characterized by Fourier transform infrared and ¹³C‐nuclear magnetic resonance spectra. PVBC was modified by ATri with 68% and Tri with 50% yield. The polymers were doped with trifluoromethanesulfonic acid (TA) at various molar ratios, X = 0.5, 1, 2, and 3 with respect to aminotriazole and triazole units. Proton transfer from TA to the triazole rings was proved with Fourier transform infrared spectroscopy. Thermogravimetric analysis showed that the samples are thermally stable up to approximately 200 °C. Differential scanning calorimetry results illustrated the homogeneity of the materials. Under anhydrous conditions, PVBCATri3TA and PVBCTri3TA showed highest proton conductivity of 0.086 and 0.042 S/cm, respectively. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

Aerosol assisted synthesis of silica/phenolic resin composite mesoporous hollow spheres

Hollow spheres of phenolic resin/silica composite are synthesized by macroscopic phase separation of a sorbitan monooleate surfactant Span 80 during aerosol-assisted spraying. The cavity can be evolved from multiple compartments to single hollow cavity with the increase of Span 80 content. The composite shell becomes mesoporous due to the release of small molecules after thermal treatment above 350 °C. After further thermal treatment at a higher temperature for example 900 °C in nitrogen or 1,450 °C in argon, the carbon/silica composite hollow spheres or crystalline silicon carbide hollow spheres are derived, respectively. Compared to the pure phenolic resin-based carbon spheres, thermal stability of the carbon-based composite spheres in air is essentially improved by the introduction of inorganic component silica. The carbon-based composite hollow spheres combine both performances of easy mass transportation through macropores and high specific surface area of mesopores, which will be promising to support catalysts for fuel cells. Electronic supplementary material  The online version of this article (doi:) contains supplementary material, which is available to authorized users.     

Morphological study on water‐borne conducting polyaniline‐poly(ethylene oxide) blends

Conducting polyaniline‐poly(ethylene oxide) blends were prepared from their aqueous solutions. The blends displayed an electrical conductivity percolation threshold as low as 1.83 wt % of polyaniline loading. As demonstrated by scanning electron microscopy, polarized optical microscopy, and wide‐angle X‐ray diffraction studies, the conducting polyaniline took a fibrillar morphology in the blend, and it existed only in the amorphous phase of poly(ethylene oxide). A three‐phase model combining morphological factors instead of a two‐phase model was proposed to explain the low‐conductivity percolation threshold. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 605–612, 2002; DOI 10.1002/polb.10114     

New hybrid membranes based on phosphonic acid functionalized silica particles for PEMFC

This work concerns the development of hybrid organic/inorganic membranes from styrenic phosphonic polymers. The phosphonic charge, composed phosphonic polymers grafted onto silica nanoparticles, was obtained by “grafting onto” method. It consists of synthesizing first the polymer, and then the terminal functions of the latter react with silanol groups of silica. The phosphonated polymer was isolated in two steps, that is, an ATRP polymerization of 4‐chloromethylstyrene followed by Mickaelïs‐Arbusov reaction. After the grafting onto silica, membranes are prepared through formulation containing the charge and the polymer matrix PVDF‐HFP, which are dispersed in DMF. The acid form is obtained by hydrolysis in chlorydric acid. The membrane possessing a 40 wt % charge ratio (IEC = 1.08 meq g^?1) was selected as reference. A proton conductivity of 65 mS cm^?1 at 80 °C was measured in immersed conditions. When the membrane is no more immersed, the value decreases drastically (0.21 mS cm^?1 at 120 °C and 25% RH). © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Comb‐shaped guanidinium functionalized poly(ether sulfone)s for anion exchange membranes: Effects of the spacer types and lengths

A series of poly(ether sulfone)‐based anion exchange membranes (AEMs), tethering with guanidinium side chains with different spacers, were synthesized via azide‐alkyne cycloaddition, deprotection, and the subsequent ion exchange reactions. The designed polymer structures were verified by the ¹H NMR spectra. Because of the appropriate water uptake and formation of interconnected ionic clusters, the GPES‐3C with propyl spacer showed higher conductivity than the GPES‐1C and GPES‐9C, with methylene and nonyl spacers, respectively. Comparatively, the GPES‐EO AEM with two ethylene oxide (EO) spacers exhibited even higher conductivity, these can be interpreted by interconnectivity of ionic channels and hydrophilicity nature of the EO spacer. Additionally, although the GPES membranes displayed sufficient thermal stability, the chemical stability of as‐prepared materials needs to be much improved for fuel cell applications. Overall, these results demonstrated that the properties of “pendent‐type” AEM can be tuned facilely by the spacer types and lengths. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55, 1313–1321     

Synthesis and properties of magnetite/poly (aniline‐co‐8‐amino‐2‐naphthalenesulfonic acid) (SPAN) nanocomposites

Composites were prepared by incorporating magnetite (Fe₃O₄) nanoparticles into the matrix of a sulfonated polyaniline (SPAN) [poly(aniline‐co‐8‐amino‐2‐naphthalenesulfonic acid) PANSA] through chemical oxidative polymerization of a mixture of aniline and 8‐amino‐2‐naphthalenesulfonic acid in the presence of magnetite nanoparticles. The composite, magnetite/SPAN(PANSA) was characterized by means of transmission electron microscopy (TEM), X‐ray diffraction (XRD), elemental analysis (EA), Fourier transform infrared (FT‐IR) spectra, UV‐vis spectroscopy, thermogravimetric analysis (TGA), conductivity and magnetic properties measurements. TEM image shows that magnetite nanoparticles were finely distributed into the SPAN matrix. XRD pattern of the nanocomposite reveals the presence of additional crystalline order through the appearance of a sharp peak at ～43° and 71°. Conductivity of the nanocomposite (0.23 S/cm) is much higher than pristine copolymer (1.97 × 10^?2 S/cm). The results of FT‐IR and UV‐visible spectroscopy reveal the presence of molecular level interactions between SO groups in SPAN and magnetite nanoparticles in the composite. Copyright © 2006 John Wiley & Sons, Ltd.     

Synthesis and characterization of polypyrrole/graphite oxide composite by in situ emulsion polymerization

This work demonstrates a feasible route to synthesize the layered polypyrrole/graphite oxide (PPy/GO) composite by in situ emulsion polymerization in the presence of cationic surfactant cetyltrimethylammonium bromide (CTAB) as emulsifier. AFM and XRD results reveal that the GO can be delaminated into nanosheets and well dispersed in aqueous solution in the presence of CTAB. The PPy nanowires are formed due to the presence of the lamellar mesostructured (CTA)₂S₂O₈ as a template. The results of the PPy/GO composite indicate the PPy insert successfully into GO interlayers, and the nanofiber‐like PPy are deposited onto the GO surface. Owing to π–π electron stacking effect between the pyrrole ring of PPy and the unoxided domain of GO sheets, the electrical conductivity of PPy/GO composite (5 S/cm) significantly improves in comparison with pure PPy nanowires (0.94 S/cm) and pristine GO (1 × 10^?6 S/cm). © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 1329–1335, 2010     

4,9‐Dihydro‐s‐indaceno[1,2‐b:5,6‐b′]dithiophene‐4,9‐dione functionalized copolymers for organic photovoltaic devices

The synthesis of conjugated polymers 1 – 5 functionalized with 4,9‐dihydro‐s‐indaceno[1,2‐b:5,6‐b′]dithiophene‐4,9‐dione in the backbone is reported and their use in the construction of organic solar cells is demonstrated. Increasing the molar ratio of 2,7‐dibromo‐3,8‐dihexyl‐4,9‐dihydro‐s‐indaceno[1,2‐b:5,6‐b′]dithiophene‐4,9‐dione, relative to 4,4′‐dihexyl‐5,5′‐dibromo‐2,2′‐bithiophene, in the copolymer synthesis significantly lowers the solubility of these polymers. The incorporation of highly conjugated 3,8‐dihexyl‐4,9‐dihydro‐s‐indaceno[1,2‐b:5,6‐b′]dithiophene‐4,9‐dione unit into the polymer backbone has been confirmed by UV–vis absorption. The observation of decreasing quantum yield for the emission in the order of 1 , 2 , 3 is consistent with copolymers with different comonomer content. The power conversion efficiencies of solar cells using blends of these polymers with PCBM ([6,6]‐phenyl C₆₁‐butyric acid methyl ester) were determined to be 0.11% for polymer 1 , 0.33% for 2 , and 0.26% for 3 , respectively. Under identical white light illumination, the power conversion efficiency of the device based on polymer 2 /PCBM as the active layer was three times higher compared to that of device based on polymer 1 /PCBM. Owing to the limited solubility and poor film‐forming ability of polymer 3 , the power conversion efficiency of solar cell based on 3 /PCBM blend is lower than that of 2 /PCBM blend, but is still larger than that of 1 /PCBM blend. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 2680–2688, 2008     

Assembled cation‐exchange/anion‐exchange polypyrrole layers as new simplified artificial muscles

A simplified artificial muscle has been constructed by assembling different polypyrrole structures in the same synthesis process. This produces not only “all‐polymeric” but rather a new generation of “all‐conducting‐polymer” artificial muscles, capable of moving in electrolytic media by an electrical current application with no evidence of delamination after several cycles. Suitable devices can be constructed for biomedical applications, based on this conducting polymer film. Copyright © 2006 John Wiley & Sons, Ltd.     

Novel electromagnetic functionalized γ‐Fe2O3/polypyrrole composite nanostructures with high conductivity

In general, the conductivity of polypyrrole (PPy) is reduced by addition of magnetic nanoparticles as the additives owing to insulating effect of magnetic nanoparticles. In this article, novel electromagnetic functionalized PPy composite nanostructures were prepared by a template‐free method associated with γ‐Fe₂O₃ nano‐needles as the hard templates in the presence of p‐toluene‐sulfonic acid (p‐TSA) and FeCl₃·6H₂O as the dopant and oxidant, respectively. It was found that the molar ratio of γ‐Fe₂O₃ to pyrrole monomer represented by [γ‐Fe₂O₃]/[Py] ratio strongly affected the morphology and the conductivity of the γ‐Fe₂O₃/PPy composite nanostructures. A growth mechanism for the composite nanostructures was proposed based on the variance of the morphology with the [γ‐Fe₂O₃]/[Py] ratio. Compared with previously reported γ‐Fe₂O₃/PPy composites, the as‐prepared novel composite nanostructures showed much higher conductivity (up to ～50 times higher). Moreover, the synthesized γ‐Fe₂O₃/PPy composite nanostructures displayed ferromagnetic behavior with a high coercive force. Explanations for these interesting observations were made in terms of the magnetic interaction between ferromagnetic γ‐Fe₂O₃ nano‐needles and spin‐polaron of PPy nanotubes. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 4446–4453, 2009     

Facile one‐step synthesis of electromagnetic functionalized polypyrrole/Fe3O4 nanotubes via a self‐assembly process

This article reports a simple self‐assembly process for facile one‐step synthesis of novel electromagnetic functionalized polypyrrole (PPy)/Fe₃O₄ composite nanotubes using p‐toluenesulfonic acid (p‐TSA) as the dopant and FeCl₃ as the oxidant. The key trick of the present method is to use FeCl₃ as the oxidant for both PPy and Fe₃O₄ in the same time to synthesize PPy/Fe₃O₄ composite nanotubes in one‐step. This facile one‐step method is much simpler than the conventional approach using the Fe₃O₄ nanoparticles as the additives. Compared to the similar composites synthesized using the conventional method, the as‐prepared PPy‐p‐TSA/Fe₃O₄ composite nanotubes using the facile one‐step self‐assembly process show much higher room‐temperature conductivity. Moreover, the composite nanotubes display interesting ferromagnetic behavior. The electrical properties of the PPy‐p‐TSA/Fe₃O₄ composite nanotubes are dominated by the amount of FeCl₃ while their magnetic properties are controlled by the amount of FeCl₂. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 320–326, 2010     

Effect of the sulfonic acid group on copolymers of aniline and toluidine with m‐aminobenzene sulfonic acid

This article describes the results of the preparation and characterization of self‐doped conducting copolymers of aniline and toluidine with m‐aminobenzene sulfonic acid. The copolymers have an intrinsic acid group that is capable of doping polyaniline. Spectroscopic, morphological, and electrical conductivity studies have provided insight into the structural and electronic properties of the copolymers. The differences in the properties of polyaniline and polytoluidine due to the sulfonic acid ring substituent on the phenyl ring are discussed. The scanning electron micrographs of the copolymers reveal regions of sharp‐edged, needle‐shaped structures, whereas the X‐ray diffraction patterns show that the copolymers are relatively more crystalline in nature. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 4065–4076, 2002     

Nanoporous and proton conductive hydrophobic–hydrophilic copolymer thermoset membranes

Copolymers of hydrophobic diglycidyl ether of bisphenol A (DGEBA) vinyl ester (VE) and hydrophilic 2‐acrylamido 2‐methyl 1‐propane sulfonic acid (AMPS) were evaluated as proton conducting membranes for fuel cell applications. Membranes were synthesized using free radical copolymerization in the presence of a common solvent for both monomers, dimethyl formamide (DMF), followed by solvent removal by supercritical CO₂ to induce porosity. Micrographs revealed pore sizes below 60 nm with porosity proportional to the initial solvent fraction used. Studies on the states of water showed that the presence of this pore volume significantly altered the freezable water fraction at equivalent AMPS concentrations. Comparison of the moles of water per mole of sulfonic acid (λ) between copolymer membranes and AMPS monomer solutions showed that the nonfreezable water (λ|_nonfr) was depressed at high AMPS concentrations, suggesting that differences in interatomic distances between sulfonic acid groups might alter λ|_nonfr. The highest average through plane conductivity of membranes was determined to be 30 mS/cm and was comparable to that of Nafion®117 (27 mS/cm). The effective proton mobility, μ_eff, was calculated and suggested to be a parameter used to capture the effects of membrane structure and swelling while acting as a comparison between different membrane types. Fuel cell tests on membranes at low ion exchange capacities were compared to Nafion®117, with suggestions on improvements of copolymer structures for improved performance. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 1245–1255, 2010