Nanofiltration membranes based on poly(vinylidene fluoride‐co‐chlorotrifluoroethylene)‐graft‐poly(styrene sulfonic acid)

Graft copolymers comprising poly(vinylidene fluoride‐co‐chlorotrifluoroethylene) backbone and poly(styrene sulfonic acid) side chains, i.e. P(VDF‐co‐CTFE)‐g‐PSSA were synthesized using atom transfer radical polymerization (ATRP) for composite nanofiltration (NF) membranes. Direct initiation of the secondary chlorinated site of CTFE units facilitates grafting of PSSA, as revealed by FT‐IR spectroscopy. The successful “grafting from” method and the microphase‐separated structure of the graft copolymer were confirmed by transmission electron microscopy (TEM). Wide angle X‐ray scattering (WAXS) also showed the decrease in the crystallinity of P(VDF‐co‐CTFE) upon graft copolymerization. Composite NF membranes were prepared from P(VDF‐co‐CTFE)‐g‐PSSA as a top layer coated onto P(VDF‐co‐CTFE) ultrafiltration support membrane. Both the rejections and the flux of composite membranes increased with increasing PSSA concentration due to the increase in SO₃H groups and membrane hydrophilicity, as supported by contact angle measurement. The rejections of NF membranes containing 47 wt% of PSSA were 83% for Na₂SO₄ and 28% for NaCl, and the solution flux were 18 and 32 L/m² hr, respectively, at 0.3 MPa pressure. Copyright © 2008 John Wiley & Sons, Ltd.     

Proton conducting grafted/crosslinked membranes prepared from poly(vinylidene fluoride‐co‐chlorotrifluoroethylene) copolymer

Poly(vinylidene fluoride‐co‐chlorotrifluoroethylene) (P(VDF‐co‐CTFE)) backbone was grafted with crosslinkable chains of poly(hydroxyl ethyl acrylate) (PHEA) and proton conducting chains of poly(styrene sulfonic acid) (PSSA) to produce amphiphilic P(VDF‐co‐CTFE)‐g‐P(HEA‐co‐SSA) graft copolymer via atom transfer radical polymerization (ATRP). Successful synthesis and microphase‐separated structure of the copolymer were confirmed by ¹H NMR, FT‐IR spectroscopy, and TEM analysis. Furthermore, this graft copolymer was thermally crosslinked with sulfosuccinic acid (SA) to produce grafted/crosslinked membranes. Ion exchange capacity (IEC) increased continuously with increasing SA contents but the water uptake increased up to 6 wt% of SA concentration, above which it decreased monotonically. The membrane also exhibited a maximum proton conductivity of 0.062 S/cm at 6 wt% of SA concentration, resulting from competitive effect between the increase of ionic groups and the degree of crosslinking. XRD patterns also revealed that the crystalline structures of P(VDF‐co‐CTFE) disrupted upon graft polymerization and crosslinking. These membranes exhibited good thermal stability at least up to 250°C, as revealed by TGA. Copyright © 2009 John Wiley & Sons, Ltd.     

Composite polymer electrolyte membranes comprising triblock copolymer and heteropolyacid for fuel cell applications

Hybrid organic/inorganic composite polymer electrolyte membranes consisting of a triblock copolymer (tBC) and varying concentrations of heteropolyacid (HPA) were investigated for application in proton exchange membrane fuel cells (PEMFC). An ABC triblock copolymer, that is, polystyrene‐b‐poly(hydroxyethyl acrylate)‐b‐poly (styrene sulfonic acid), PS‐b‐PHEA‐b‐PSSA, at 28:21:51 wt % was synthesized via atom transfer radical polymerization (ATRP) and solution‐blended with a commercial HPA. Upon the incorporation of HPA into the tBC, the symmetric stretching bands of both the SO group (1187 cm^?1) and the ? OH group (3440 cm^?1) shifted to lower wavenumbers (1158 and 3370 cm^?1). The shift in these FTIR absorptions suggest that the HPA particles strongly interact with both the sulfonic acid groups in the PSSA domains and the hydroxyl groups in the PHEA domains. When the weight fraction of HPA was increased to 0.2, the room‐temperature proton conductivity of the composite membrane increased from 0.048 to 0.065 S/cm, presumably because of the intrinsic conductivity of the HPA particles and the enhanced acidity of the sulfonic acid in the tBC. The water uptake of the composite membranes decreased from 130 to 48% with an increase of the HPA weight fraction to 0.4. The decrease in water uptake is likely a result of the decrease in the number of available water absorption sites because of the hydrogen bonding interaction between the HPA particles and the tBC matrix. Scanning electron microscopy and transmission electron microscopy images showed that the HPA nanoparticles with a diameter of 200–300 nm were uniformly distributed throughout the tBC matrix up to an HPA weight fraction of 0.4. Thermal stability of the composite membranes (decomposition temperature > 400 °C) was enhanced as compared with the pristine tBC membrane, presumably because of the strong specific interaction of the HPA particles with the sulfonic acid and hydroxyl groups. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 691–701, 2008     

Proton conducting membranes based on poly(vinyl chloride) graft copolymer electrolytes

The direct preparation of proton conducting poly(vinyl chloride) (PVC) graft copolymer electrolyte membranes using atom transfer radical polymerization (ATRP) is demonstrated. Here, direct initiation of the secondary chlorines of PVC facilitates grafting of a sulfonated monomer. A series of proton conducting graft copolymer electrolyte membranes, i.e. poly(vinyl chloride)‐g‐poly(styrene sulfonic acid) (PVC‐g‐PSSA) were prepared by ATRP using direct initiation of the secondary chlorines of PVC. The successful syntheses of graft copolymers were confirmed by ¹H‐NMR and FT‐IR spectroscopy. The images of transmission electron microscopy (TEM) presented the well‐defined microphase‐separated structure of the graft copolymer electrolyte membranes. All the properties of ion exchange capacity (IEC), water uptake, and proton conductivity for the membranes continuously increased with increasing PSSA contents. The characterization of the membranes by thermal gravimetric analysis (TGA) also demonstrated their high thermal stability up to 200°C. The membranes were further crosslinked using UV irradiation after converting chlorine atoms to azide groups, as revealed by FT‐IR spectroscopy. After crosslinking, water uptake significantly decreased from 207% to 84% and the tensile strength increased from 45.2 to 71.5 MPa with a marginal change of proton conductivity from 0.093 to 0.083 S cm^?1, which indicates that the crosslinked PVC‐g‐PSSA membranes are promising candidates for proton conducting materials for fuel cell applications. Copyright © 2008 John Wiley & Sons, Ltd.     

Selectively sulfonated poly(aryl ether sulfone)‐b‐polybutadiene for proton exchange membrane

A series of selectively sulfonated poly(arylene ether sulfone)‐b‐polybutadiene copolymers (SPAES‐b‐PB) were prepared based on carboxyl terminated polybutadiene (CTPB) and sulfonated poly(arylene ether sulfone) (SPAES) that was directly prepared by polycondensation of 4,4′‐isopropylidenediphenol with different molar ratios of disodium 3,3′‐disulfonate‐4,4′‐dichlorodiphenyl sulfone (SDCDPS) to 4,4′‐dichlorodiphenylsulfone (DCDPS), and subsequent selective postsulfonation of flexible PB block was carried out. Epoxidized modification of membranes was conducted by an in situ‐generated peracid method. The content of sulfonic acid groups attaching to aromatic rings in SPAES was determined by ¹H NMR and was in good aggrement with the controlled ratios. The effect of sulfonated rigid blocks on the postsulfonation of PB blocks was studied by Fourier transform infrared spectroscopy. The glass transition temperature (T_g) and the temperature of the melting peak (T) of membranes in acid form were studied by differential scanning calorimetry. Fenton's reagent test revealed that the selectively sulfonated SPAES‐b‐PB membranes had good stability to oxidation. The microstructure of rod‐like rigid SPAES blocks and interpenetrating network of ions were observed by transmission electron microscopy. Complex impedance measurement showed that an epoxidized membrane with SPAES‐40 exhibited the highest proton conductivity (1.08 × 10^?1 S/cm, 90 °C), which was due to the formation of obvious ionic networks. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 665–672, 2006     

Characterization and evaluation of commercial poly (vinylidene fluoride)‐g‐sulfonatedPolystyrene as proton exchange membrane

The possibility of developing low‐cost commercial grafted and sulfonated Poly(vinylidene fluoride) (PVDF‐g‐PSSA) membranes as proton exchange membranes for fuel cell applications have been investigated. PVDF‐g‐PSSA membranes were systematically prepared and examined with the focus of understanding how the polymer microstructure (degree of grafting and sulfonation, ion‐exchange capacity, etc) affects their methanol permeability, water uptake, and proton conductivity. Fourier transform infrared spectroscopy was used to characterize the changes of the membrane's microstructure after grafting and sulfonation. The results showed that the PVDF‐g‐PSSA membranes exhibited good thermal stability and lower methanol permeability. The proton conductivity of PVDF‐g‐PSSA membranes was also measured by the electrochemical impedance spectroscopy method. It was found that the proton conductivity of PVDF‐g‐PSSA membranes depends on the degree of sulfonation. All the sulfonated membranes show high proton conductivity at 92°C, in the range of 27 to 235 mScm⁻¹, which is much higher than that of Nafion212 (102 mScm⁻¹ at 80°C). The results indicated that the PVDF‐g‐PSSA membranes are particularly promising membranes to be used as polymer electrolyte membranes due to their excellent stability, low methanol permeability, and high proton conductivity.     

Synthesis and characterization of grafted/crosslinked proton conducting membranes based on amphiphilic PVDF copolymer

A novel graft copolymer consisting of a poly(vinylidene fluoride‐co‐chlorotrifluoroethylene) backbone and poly(glycidyl methacrylate) side chains, that is, P(VDF‐co‐CTFE)‐g‐PGMA, was synthesized through atom transfer radical polymerization (ATRP) using CTFE units as a macroinitiator. Successful synthesis and microphase‐separated structure of the polymer were confirmed by ¹H NMR, FTIR spectroscopy, and TEM. As‐synthesized P(VDF‐co‐CTFE)‐g‐PGMA copolymer was sulfonated by sodium bisulfite, followed by thermal crosslinking with sulfosuccinic acid (SA) via the esterification to produce grafted/crosslinked polymer electrolyte membranes. The IEC values continuously increased with increasing SA content but water uptake increased with SA content up to 10 wt %, above which it decreased again as a result of competitive effect between crosslinking and hydrophilicity of membranes. At 20 wt % of SA content, the proton conductivity reached 0.057 and 0.11 S/cm at 20 and 80 °C, respectively. The grafted/crosslinked P(VDF‐co‐CTFE)‐g‐PGMA/SA membranes exhibited good mechanical properties (>400 MPa of Young's modulus) and high thermal stability (up to 300 °C), as determined by a universal testing machine (UTM) and TGA, respectively. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 1110–1117, 2010     

Styrene grafted ethylene chlorotrifluoroethylene (ECTFE‐g‐PSSA) protonic membranes: Preparation,characterization, and transport mechanism

The main goal of the present work is the development of partially fluorinated, low‐cost proton exchange membranes. The styrene grafted onto commercial ethylene chlorotrifluoroethylene (ECTFE) membranes using solution grafting technique, and after that the membranes were sulfonated. Diluting styrene on ECTFE with a solvent mixture of methanol plus methylene chloride (1:1) was highly effective in promoting the grafting reaction as indicated by the increase in the degree of grafting (DG) to 21.3% compared to other solvents. The DG in ECTFE membranes increased with an increase in the monomer concentration up to 60% and then declined. Fourier transform infrared spectroscopic analysis confirmed grafting and sulfonation onto ECTFE films. The maximum value of proton conductivity for ECTFE‐g‐PSSA film with DG = 21.3% was observed to be 141 mS cm⁻¹, which is also higher than those of Nafion 212 membrane. Furthermore, the activation energy of ECTFE‐g‐PSSA membranes was obtained ranging from 8.27 to 9.726 kJ mol⁻¹. So both proton transport mechanisms (hopping and vehicle) have been commonly accepted. The mobility of the charge carriers calculated from proton conductivity data has robust dependence on the grafting yield and temperature. Moreover, the tensile strength and elongation at break ratio decreases with the increase in DG. The water and methanol uptakes increase up to 0.97% and 30%, respectively, for the highest DG value. Finally, the ECTFE‐g‐PSSA has lower cost and higher conductivity they could be better used instead of Nafion in direct methanol fuel cells.     

P (VDF‐co‐CTFE)‐g‐P2VP amphiphilic graft copolymers: Synthesis,structure, and permeation properties

A series of amphiphilic graft copolymers of poly (vinylidene fluoride‐co‐chlorotrifluoroethylene)‐g‐poly(2‐vinyl pyridine), P (VDF‐co‐CTFE)‐g‐P2VP, with different degrees of P2VP grafting (from 26.3 to 45.6 wt%) was synthesized via one‐pot atom transfer radical polymerization (ATRP). The amphiphilic properties of P (VDF‐co‐CTFE)‐g‐P2VP graft copolymers allowed itself to self‐assemble into nanoscale structures. P (VDF‐co‐CTFE)‐g‐P2VP graft copolymers were introduced into neat P (VDF‐co‐CTFE) as additives to form blending membranes. When two different solvents, N‐methyl‐2‐pyrrolidone (NMP) and dimethylformamide (DMF), were used, specific organized crystalline structures were observed only in the NMP systems. P (VDF‐co‐CTFE)‐g‐P2VP played a pivotal role in controlling the morphology and pore structure of membranes. The water flux of the membranes increased from 57.2 to 310.1 L m^?2 h^?1 bar^?1 with an increase in the PVDF‐co‐CTFE‐g‐P2VP loading (from 0 to 30 wt%) due to increased porosity and hydrophilicity. The flux recovery ratio (FRR) increased from 67.03% to 87.18%, and the irreversible fouling (R_ir) decreased from 32.97% to 12.82%. Moreover, the pure gas permeance of the membranes with respect to N₂ was as high as 6.2 × 10⁴ GPU (1 GPU = 10^–6 cm³[STP]/[s cm² cmHg]), indicating their possible use as a porous polymer support for gas separation applications.     

Antifouling poly(vinylidene fluoride) ultrafiltration membranes containing amphiphilic comb polymer additive

An amphiphilic comb polymer consisting of poly(vinylidene fluoride‐co‐chlorotrifluoroethylene) [P(VDF‐co‐CTFE)] main chains and poly(oxyethylene methacrylate) (POEM) side chains was synthesized using direct initiation of the chlorine atoms in CTFE units through atom transfer radical polymerization, as confirmed by ¹H NMR and FTIR spectroscopy. The P(VDF‐co‐CTFE)‐g‐POEM comb polymer was introduced as an additive to prepare poly(vinylidene fluoride) antifouling ultrafiltration membranes. As the contents of comb polymer increased, the mechanical properties of membranes slightly decreased due to the decreased crystallinity of the membranes, as revealed by universal testing machine and X‐ray diffraction. However, water contact angle measurement and X‐ray photoelectron spectroscopy showed that the hydrophilic POEM segments spontaneously segregated on the membrane surfaces. As a result, the antifouling property of the membranes containing P(VDF‐co‐CTFE)‐g‐POEM comb polymer was considerably improved with a slight change of water flux. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 183–189, 2010     

Preparation and characterization of PVDF‐based blend membranes as polymer electrolyte membranes in fuel cells: Study of factor affecting the proton conductivity behavior

There is a huge demand especially for polyvinylidene fluoride (PVDF) and its copolymers to provide high performance solid polymer electrolytes for use as an electrolyte in energy supply systems. In this regard, the blending approach was used to prepare PVDF‐based proton exchange membranes and focused on the study of factor affecting the ir proton conductivity behavior. Thus, a series of copolymers consisting of poly (methyl methacrylate) (PMMA), polyacrylonitrile (PAN), and poly(2‐acrylamido‐2‐methyl‐l‐propanesulfonic acid) (PAMPS) as sulfonated segments were synthesized and blended with PVDF matrix in order to create proton transport sites in PVDF matrix. It was found that addition of PMMA‐co‐PAMPS and PAN‐co‐PAMPS copolymers resulted in a significant increase in porosity, which favored the water uptake and proton transport at ambient temperature. Furthermore, crystallinity degree of the PVDF‐based blend membranes was increased by addition of the related copolymers, which is mainly attributed to formation of hydrogen bonding interaction between PVDF matrix and the synthesized copolymers, and led to a slight decrease in proton conductivity behavior of blend membranes. From impedance data, the proton conductivity of the PVDF/PMMA‐co‐PAMPS and PVDF/PAN‐co‐PAMPS blend membranes increases to 10 and 8.4 mS cm⁻¹ by adding only 50% of the related copolymer (at 25°C), respectively. Also, the blend membranes containing 30% sulfonated copolymers showed a power density as high as 34.30 and 30.10 mW cm⁻² at peak current density of 140 and 79.45 mA cm⁻² for the PVDF/PMMA‐co‐PAMPS and PVDF/PAN‐co‐PAMPS blend membranes, respectively. A reduction in the tensile strength was observed by the addition of amphiphilic copolymer, whereas the elongation at break of all blend membranes was raised.     

Sorption and diffusion of methanol and water in PVDF‐g‐PSSA and Nafion® 117 polymer electrolyte membranes

Sorption and diffusion properties of poly(vinylidene fluoride)‐graft‐poly(styrene sulfonic acid) (PVDF‐g‐PSSA) and Nafion® 117 polymer electrolyte membranes were studied in water/methanol mixtures. The two types of membranes were found to have different sorption properties. The Nafion 117 membrane was found to have a maximum in‐solvent uptake around 0.4 to 0.6 mole fraction of methanol, while the PVDF‐g‐PSSA membranes took up less solvent with increasing methanol concentration. The proton NMR spectra were recorded for membranes immersed in deuterated water/methanol mixtures. The spectra showed that the hydroxyl protons inside the membrane exhibit resonance lines different from the resonance lines of hydroxyl protons in the external solvent. The spectral features of the lines of these internal hydroxyl groups in the membranes were different in the Nafion membrane compared with the PVDF‐g‐PSSA membranes. Diffusion measurements with the pulsed field gradient NMR (PFG‐NMR) method showed that the diffusion coefficient of the internal hydroxyl groups in the solvent immersed Nafion membrane mirrors the changes in the diffusion coefficients of hydroxyl and methyl protons in the external solvent. For the PVDF‐g‐PSSA membranes, a decrease in the diffusion coefficient of the internal hydroxyl protons was seen with increasing methanol concentration. These results indicate that the morphology and chemical structure of the membranes have an effect on their solvent sorption and diffusion characteristics. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 3277–3284, 2000     

Synthesis and characterizations of well‐defined branched polymers with AB2 branches by combination of RAFT polymerization and ROP as well as ATRP

A well‐defined branched copolymer with PLLA‐b‐PS₂ branches was prepared by combination of reversible addition‐fragmentation transfer (RAFT) polymerization, ring‐opening polymerization (ROP), and atom transfer radical polymerization (ATRP). The RAFT copolymerization of methyl acrylate (MA) and hydroxyethyl acrylate (HEA) yielded poly(MA‐co‐HEA), which was used as macro initiator in the successive ROP polymerization of LLA. After divergent reaction of poly(MA‐co‐HEA)‐g‐PLLAOH with divergent agent, the macro initiator, poly(MA‐co‐HEA)‐g‐PLLABr₂ was formed in high conversion. The following ATRP of styrene (St) produced the target polymer, poly(MA‐co‐HEA)‐g‐(PLLA‐b‐PS₂). The structures, molecular weight, and molecular weight distribution of the intermediates and the target polymers obtained from every step were confirmed by their ¹H NMR and GPC measurements. DSC results show one T = 3 °C for the poly(MA‐co‐HEA), T = ?5 °C, T= 122 °C, and T = 157 °C for the branched copolymers (poly(MA‐co‐HEA)‐g‐PLLA), and T = 51 °C, T = 116 °C, and T = 162 °C for poly(MA‐co‐HEA)‐g‐(PLLA‐b‐PS₂). © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 549–560, 2006     

Templated synthesis of silver nanoparticles in amphiphilic poly(vinylidene fluoride‐co‐chlorotrifluoroethylene) comb copolymer

In this study, poly(vinylidene fluoride‐co‐chlorotrifluoroethylene)‐graft‐poly(oxyethylene methacrylate), P(VDF‐co‐CTFE)‐g‐POEM, an amphiphilic comb copolymer with hydrophobic P(VDF‐co‐CTFE) backbone and hydrophilic POEM side chains at 73:27 wt % was synthesized. The POEM side chains were grafted from the P(VDF‐co‐CTFE) mainchain backbone via atom transfer radical polymerization (ATRP) using direct initiation of the chlorine atoms in CTFE units. Synthesis of microphase‐separated P(VDF‐co‐CTFE)‐g‐POEM comb copolymer was successful, as confirmed by nuclear magnetic resonance (¹H NMR), FTIR spectroscopy, and transmission electron microscopy (TEM). Nanocomposite films were prepared using the comb copolymer as a template film and the in situ reduction of AgCF₃SO₃ precursor to silver nanoparticles under UV irradiation. Silver nanoparticles with 4–8 nm in average size were in situ created in the solid state template film, as revealed by TEM, UV–visible spectroscopy, and wide angle X‐ray scattering (WAXS). Differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA) presented the selective incorporation and the in situ growth of silver nanoparticles within the hydrophilic POEM domains of microphase‐separated comb copolymer film. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 702–709, 2008     

Synthesis and properties of amphoteric copolymer of 5‐vinyltetrazole and vinylbenzyl phosphonic acid

Amphoteric polymers have been studied for various applications such as separation of low molecular weight organic molecules from inorganic salt mixtures, selective ion transport, drug delivery through membranes of biological interest, separation of ionic drugs and proteins, and separation of alcohol and water. Typical amphoteric polymers consist of weak base and weak acid groups. In present study, the copolymerization of 5‐vinyltetrazole (VT) and diisopropyl‐p‐vinylbenzyl phosphate (DIPVBP) via free radical polymerization is studied. The reactivity ratio of VT and DIPVBP, which is calculated from Kelen‐Tudos plot, is 0.251 and 0.345, respectively. The amphoteric copolymer of VT and diisopropyl‐p‐vinylbenzyl phosphonic acid (poly(VT‐co‐VBPA)) is obtained from hydrolysis of the copolymer of VT and DIPVBP (poly(VT‐co‐DIPVBP)). Poly(VT‐co‐VBPA) is thermally stable under 190 °C. The anhydrous proton conductivity of amphoteric poly(VT‐co‐VBPA) can reach 1.54 × 10^‐4 S cm^?1 at 170 °C with an activation energy of 114.7 kJ mol^?1. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013 , 51, 3486–3493     

Preparation and characterization of a poly(vinylbenzyl sulfonic acid)‐grafted FEP membrane

In this study, a novel polymer electrolyte membrane, poly(vinylbenzyl sulfonic acid)‐grafted poly(tetrafluoroethylene‐co‐hexafluoropropylene) (FEP‐g‐PVBSA), has been successfully prepared by simultaneous irradiation grafting of vinylbenzyl chloride (VBC) monomer onto a FEP film and taking subsequent chemical modification steps to modify the benzyl chloride moiety to the benzyl sulfonic acid moiety. The chemical reactions for the sulfonation were carried out via the formation of thiouronium salt with thiourea, base‐catalyzed hydrolysis for the formation of thiol, and oxidation with hydrogen peroxide. Each chemical conversion process was confirmed by FTIR, elemental analysis, and SEM‐EDX. A chemical stability study performed with Fenton's reagent (3% H₂O₂ solution containing 4 ppm of Fe²⁺) at 70 °C revealed that FEP‐g‐PVBSA has a higher chemical stability than the poly(styrene sulfonic acid)‐grafted membranes (FEP‐g‐PSSA). © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 563–569, 2010     

Synthesis of proton‐conducting block copolymer membranes composed of a fluorinated segment and a sulfonic acid segment

Diblock copolymer membranes having a fluorinated segment and a sulfonic acid segment were prepared by living radical polymerization, solution casting, and crosslinking, followed by heat treatment. Diblock copolymers of 2,3,4,5,6‐pentafluorostyrene (PFS)/4‐(1‐methylsilacyclobutyl)styrene (SBS) and neopentyl styrenesulfonate (SSPen) (poly(PFS‐co‐SBS)‐b‐polySSPen)s were synthesized by nitoroxy‐mediated living radical polymerization. Self‐standing crosslinked membranes were obtained by casting a THF solution of the block copolymer with Pt catalyst. Heat treatment of the membrane at 230 °C induced decomposition of the neopentyl sulfonate esters to provide block copolymer membranes having a fluorinated segment and a free sulfonic acid segment. It was confirmed that the block copolymer with a high sulfonic acid content exhibited high ion exchange capacity and high proton conductivity as well as high thermal stability. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 4479–4485, 2008     

Synthesis of original para‐sulfonic acid aminoethylthioethylbenzenesulfonic by telomerization,and its grafting onto poly(VDF‐co‐HFP) copolymers for proton exchange membrane for fuel cell

The synthesis of a novel aromatic sulfonic acid bearing an amino function H₂N? C₂H₄? S? C₂H₄? C₆H₄? SO₃Na ( 1 ) from the radical addition of mercaptoethylamine hydrochloride onto styrene sodium sulfonate, and its subsequent grafting onto poly(vinylidene fluoride‐co‐hexafluoropropylene), poly(VDF‐co‐HFP), copolymer are presented. First, the radical telomerization, carried out under radical conditions and in water, led to various products [monoadduct ( 1 ), multiadducts, and polymers], the amounts of which depend on the experimental conditions and [mercaptan]₀/[monomer]₀ initial molar ratio (R₀). An R₀ ≥ 1 led to the monoadduct ( 1 ) only and achieved in ～85% yield. The zwitterionic isomer was obtained mainly and its chemical modification was possible to get an original aromatic sodium sulfonate containing an amino end group. A kinetic study of the telomerization was presented for R₀ < 1. Thermogravimetric analysis of the telomer showed that this compound was stable up to 200 °C. Second, the grafting of ( 1 ) onto poly(VDF‐co‐HFP) copolymer was also investigated. Such a grafting proceeded as expected by a classic mechanism of grafting of amines. Molar percentages of grafted telomer were assessed by ¹H NMR spectroscopy and by elemental analysis. Ion exchange capacity (IEC) values of the membranes were deduced from the mol % grafted telomer. Scanning electron microscopy pictures showed a good homogeneity in the cross‐section of membranes, and energy dispersive X‐ray evidenced that all SO₃Na groups of the grafted amine were changed into SO₃H after treatment with concentrated HCl. Method involving an impedance analyzer, working at increasing high frequencies was used to assess the protonic conductivities, σ. These values were lower than that of Nafion117^®, but σ increased with the IEC to 0.4 mS/cm at room temperature and 95% relative humidity. Water and methanol uptakes were also assessed, and it was shown that σ increased when water uptakes increased. Membranes started to decompose from 170 °C under air. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 121–136, 2009     

Phase separation and crystallinity in proton conducting membranes of styrene grafted and sulfonated poly(vinylidene fluoride)

A series of proton exchange membranes have been prepared by the preirradiation grafting method. Styrene was grafted onto a matrix of poly(vinylidene fluoride) (PVDF) after electron beam irradiation. Part of the samples was crosslinked with divinylbenzene (DVB) or bis(vinylphenyl)ethane (BVPE). Subsequent sulfonation gave membranes grafted with poly(styrene sulfonic acid) and marked PVDF‐g‐PSSA. It was found that the intrinsic crystallinity of the matrix decreased in both the grafting and the sulfonation reaction in all the membranes. The graft penetration and the ion conductivity are influenced strongly by the crosslinker. The ion conductivity is considerably lower in crosslinked membranes than in noncrosslinked ones. Generally, the mechanical strength decreases with crosslinking. The membranes show a regular phase separated structure in which the sulfonated grafts are incorporated in the amorphous parts of the matrix polymer. The phase separated domains are small, of the order of magnitude of 100–250 nm. These were resolved on transmission electron micrographs and on atomic force images but could not be resolved with microprobe Raman spectroscopy. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 1741–1753, 1999     

Synthesis of unsaturation containing P(VDF‐co‐TrFE‐co‐CTFE) from P(VDF‐co‐CTFE) in one‐pot catalyzed with Cu(0)‐based single electron transfer living radical polymerization system

Poly(vinylidene fluoride‐co‐trifluoroethylene‐co‐chlorotrifluoroethylene) (P(VDF‐co‐TrFE‐co‐CTFE)) with internal double bond has been reported with high dielectric constant and energy density at room temperature, which is expected to serve as a promising dielectric film in high pulse discharge capacitors. An environmentally friendly one‐pot route, including the controllable hydrogenation via Cu(0) mediated single electron transfer radical chain transfer reaction (SET‐CTR) and dehydrochlorination catalyzed with N‐containing reagent, is successfully developed to synthesize P(VDF‐co‐TrFE‐co‐CTFE) containing unsaturation. The resultant polymer was carefully characterized with ¹H NMR, ¹⁹F NMR, and FTIR. The composition of the resultant copolymer is strongly influenced by reaction conditions, including the reaction temperature, catalyst concentration, the types of ligands and solvents. The kinetics data of the chain transfer and elimination reaction demonstrate their well‐controlled feature of the strategy. By shifting the equilibrium between the CTR and elimination reactions dominated by N‐compounds serving as ligands in SET‐CTR and catalyst in the dehydrochlorination of P(VDF‐co‐CTFE), P(VDF‐co‐TrFE‐co‐CTFE) with tunable TrFE and double‐bond content could be synthesized in this one‐pot route. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 3429–3440