Morphology and mechanical and viscoelastic properties of natural rubber and styrene butadiene rubber latex blends

The morphology and mechanical and viscoelastic properties of a series of blends of natural rubber (NR) and styrene butadiene rubber (SBR) latex blends were studied in the uncrosslinked and crosslinked state. The morphology of the NR/SBR blends was analyzed using a scanning electron microscope. The morphology of the blends indicated a two phase structure in which SBR is dispersed as domains in the continuous NR matrix when its content is less than 50%. A cocontinuous morphology was obtained at a 50/50 NR/SBR ratio and phase inversion was seen beyond 50% SBR when NR formed the dispersed phase. The mechanical properties of the blends were studied with special reference to the effect of the blend ratio, surface active agents, vulcanizing system, and time for prevulcanization. As the NR content and time of prevulcanization increased, the mechanical properties such as the tensile strength, modulus, elongation at break, and hardness increased. This was due to the increased degree of crosslinking that leads to the strengthening of the 3‐dimensional network. In most cases the tear strength values increased as the prevulcanization time increased. The mechanical data were compared with theoretical predictions. The effects of the blend ratio and prevulcanization on the dynamic mechanical properties of the blends were investigated at different temperatures and frequencies. All the blends showed two distinct glass‐transition temperatures, indicating that the system is immiscible. It was also found that the glass‐transition temperatures of vulcanized blends are higher than those of unvulcanized blends. The time–temperature superposition and Cole–Cole analysis were made to understand the phase behavior of the blends. The tensile and tear fracture surfaces were examined by a scanning electron microscope to gain an insight into the failure mechanism. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 2189–2211, 2000     

Improving properties of natural rubber/polyamide 12 blends through grafting of diacetone acrylamide functional group

The aim of the present study was to improve the compatibility in blends of natural rubber (NR) and polyamide 12 (PA12) by grafting NR with hydrophilic monomer, diacetone acrylamide (DAAM), via seeded emulsion polymerization. The increase in polarity of NR after grafting modification was confirmed by a considerable increase in the polar component of its surface energy. Blends of graft copolymers of NR and poly(diacetone acrylamide) prepared using 10 wt% of DAAM (NR‐g‐PDAAM10) and PA12 were prepared at a 60/40 blend ratio (wt%) using simple blend and dynamic vulcanization techniques. The mechanical and rheological properties of the resulting blends were subsequently investigated and compared with those of the corresponding blends based on unmodified NR. The results show that dynamic vulcanization led to a significant increase in both mechanical and rheological properties of the blends. It was also observed that the dynamically cured NR‐g‐PDAAM10/PA12 blend had smaller particle size of vulcanized rubber dispersed in the PA12 matrix than observed for the dynamically cured NR/PA12 blend. This is due to the compatibilizing effect of DAAM groups present in NR‐g‐PDAAM10 molecule, which decreases the interfacial tension between the two polymeric phases. Therefore, it can be stated that the interfacial adhesion between NR and PA12 was improved by the presence of DAAM groups in NR molecule. This was reflected in the higher tensile properties observed in the dynamically cured NR‐g‐PDAAM10/PA12 blend. Copyright © 2017 John Wiley & Sons, Ltd.     

Cure temperature influence on natural rubber—A small angle X‐ray scattering study

To analyze the natural rubber behavior during vulcanization under different cure treatments, an experimental investigation using small angle X‐ray scattering was performed. To achieve this, a set of samples were prepared using sulfur and N‐t‐butyl‐2‐benzothiazole sulfenamide as accelerator and then cured at temperatures between 403 and 463 K reaching their optimum mechanical properties considering rheometer tests. The crosslink density of the samples was evaluated by means of the swelling technique in solvent. In the usual Lorentz corrected representation of the X‐ray scattered intensity, a maximum was observed in the plots corresponding to the cured samples, revealing a highly correlated structure. This maximum shifted toward higher values of the scattering vector when the cure temperature of the samples increased. This behavior is discussed in terms of the crosslinks type present in the vulcanized rubber network at different cure temperatures. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 2966–2971, 2007     

Natural rubber/styrene-butadiene rubber blends prepared by solution mixing: Influence of vulcanization temperature using a Semi-EV sulfur curing system on the microstructural properties

Blends of natural rubber (NR) and styrene-butadiene rubber (SBR) were prepared by solution mixing and vulcanized with sulfur and accelerator in a Semi-EV system at 433 K and 443 K in order to study the vulcanization kinetic and the influence of vulcanization temperature on final structure of the blends. The vulcanization kinetic studied through the variation in rheometer curves was analyzed using the Ding and Leonov model, which takes into account the reversion effect during the cure process. The average free nanohole volume and the fractional free volume of samples with different NR/SBR ratio were estimated using positron annihilation lifetime spectroscopy (PALS). Also, the crosslink density was determined by means of swelling tests in a solvent. For all the compounds, a correlation between the free nanohole volume and the delta torque obtained from the respective rheometer curves was established.     

Effects of vulcanization accelerator functionalized graphene on the co-vulcanization kinetics and mechanical strength of NR/SBR blends

Rubber blends are widely used for combining the advantages of individual rubber component. However, to date, how to determine and distinguish the vulcanization kinetics for each single rubber phase in rubber blends during the co-vulcanization process are still a challenge. Herein, high resolution pyrolysis gas chromatography-mass spectrometry (PyGC-MS) was employed for the first time to investigate the vulcanization kinetics of natural rubber (NR) and styrene-butadiene rubber (SBR) in their blends filled with graphene. It is shown that the crosslinking rate of NR chains (k_NR) was much lower than that of SBR chains (k_SBR) in the unfilled blends and blends with untreated graphene. Interestingly, the gap between k_SBR and k_NR was narrowed effectively in the blends with vulcanization accelerator grafted graphene, showing a better co-vulcanization of NR and SBR. In addition, the vulcanization accelerator grafted graphene was uniformly dispersed in rubber matrix and endowed rubber blends with higher mechanical strength and thermal conductivity did the untreated graphene.     

Dynamically cured natural rubber/EVA blends: influence of NR‐g‐poly(dimethyl (methacryloyloxymethyl)phosphonate) compatibilizer

Graft copolymer of natural rubber and poly(dimethyl(methacryloyloxymethyl)phosphonate) (NR‐g‐PDMMMP) was prepared in latex medium via photopolymerization. It was then used to promote the blend compatibility of dynamically cured 40/60 natural rubber (NR)/ethylene vinylacetate copolymer (EVA) blends using various loading levels at 1, 3, 5, 7, 9, 12, and 15 wt%. It was found that the increasing loading levels of NR‐g‐PDMMMP in the blends caused the increasing elastic modulus and complex viscosity until reaching the maximum values at a loading level of 9 wt%. The properties thereafter decreased with the increasing loading levels of NR‐g‐PDMMMP higher than 9 wt%. The smallest vulcanized rubber particles dispersed in the EVA matrix with the lowest tan δ value was also observed at a loading level of 9 wt%. Furthermore, the highest tensile strength and elongation at break (i.e., 17.06 MPa and 660%) as well as the lowest tension set value (i.e., 27%) were also observed in the blend using this loading level of the compatibilizer. Addition of NR‐g‐PDMMMP in the dynamically cured NR/EVA blends also improved the thermal stability of the blend. That is, the decomposition temperature increased with the addition of the graft copolymer. However, the addition of NR‐g‐PDMMMP in the blends caused the decreasing degree of crystallinity of the EVA phase in the blend. However, the strength properties of the blend are still high because of the compatibilizing effect. Copyright © 2009 John Wiley & Sons, Ltd.     

Microbial desulfurization of SBR ground rubber by Sphingomonas sp. and its utilization as filler in NR compounds

Microbial desulfurization of waste tyre rubber has been investigated with great efforts since 1990s, because waste rubber has created serious ecological and environmental problems. A microbial desulfurization technique for SBR ground rubber has been developed by a novel sulfur‐oxidizing bacterium Sphingomonas sp. The adaptability of Sphingomonas sp. with SBR ground rubber was tested with the amounts of SBR ground rubber varying from 0.5 to 4% g/l. The sol fraction of desulfurized SBR ground rubber increased 70%, compared with SBR ground rubber without desulfurization. Fourier transform infrared spectroscopy‐attenuated total reflectance (FTIR‐ATR) spectrum and X‐ray photoelectron spectroscopy (XPS) analysis of the desulfurized surface of vulcanized SBR flakes revealed that not only the oxidation of crosslinked S? S and S? C bonds, but also the rupture of C?C double bonds had happened to SBR vulcanizates during microbial desulfurization. The cure characteristics, such as scorch time and optimum cure time of natural rubber (NR) vulcanizates filled, were found to decrease with increasing contents of desulfurized SBR ground rubber, due to some reactive groups on its surface. NR vulcanizates filled with desulfurized SBR ground rubber had lower crosslink density and hardness, higher tensile strength and elongation at break, compared with those filled with SBR ground rubber of the same amount. Dynamic mechanical properties indicated that there were better crosslink distribution and stronger interfacial bonding between NR matrix and desulfurized SBR ground rubber. Scanning electron microscope (SEM) photographs showed that the fracture surfaces of NR vulcanizates filled with desulfurized SBR ground rubber had more smooth morphologies. Copyright © 2010 John Wiley & Sons, Ltd.     

Fracture toughness of nylon‐6 blends with maleated rubbers

The fracture toughness of blends of nylon‐6 with maleated ethylene–propylene rubber and maleated styrene/hydrogenated butadiene/styrene triblock copolymer was investigated with a single‐edge‐notched three‐point‐bending instrumented Dynatup test. The blends for which the rubber particle size was less than 0.7 μm fractured in a ductile manner over the whole range of ligament lengths, whereas the blends with particles larger than 0.7 μm showed a ductile‐to‐brittle transition with the ligament length. In this regime, ductile fracture was observed for specimens with short ligaments, whereas brittle fracture was seen for those with long ligaments. The ductile fracture behavior was analyzed with the essential‐work‐of‐fracture model, whereas linear elastic fracture mechanics techniques were used to analyze the brittle fracture behavior. The fact that the ductile fracture energy was larger for the blends with the styrene/hydrogenated butadiene/styrene triblock copolymer than for those with ethylene–propylene rubber was due to the larger dissipative energy density of the blends based on the styrene/hydrogenated butadiene/styrene triblock copolymer. Both the critical strain energy release rate (G_IC) and the plane‐strain critical stress intensity factor (K_IC) increased as the rubber particle size decreased for both blend systems. The G_IC and K_IC parameters had similar values, regardless of the rubber type, when the rubber particle size was fixed. The transition ligament length was near the size criterion for plane‐strain conditions for both blend systems. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1739–1758, 2004     

Thermal stability and ageing properties of sulphur and gamma radiation vulcanized natural rubber (NR) and carboxylated styrene butadiene rubber (XSBR) latices and their blends

The thermal stability of natural rubber (NR) and carboxylated styrene butadiene rubber (XSBR) latices and their blends was studied by thermogravimetric methods. Ageing characteristics of these latex blends were studied by applying hot air oven thermal ageing for seven days at 70 °C. The mechanical properties of the aged samples were studied. Thermal degradation and ageing properties of these individual latices and their blends were investigated with special reference to blend ratio and vulcanization techniques. As the XSBR content in the blends increased their thermal stability was also found to increase. Among sulphur and radiation-vulcanized samples, radiation cured possesses higher thermal stability due to the higher thermal stability of carbon-carbon crosslinks. DTG curves were used for the determination of different stages involved in the degradation. Activation energy for degradation was determined from Coats-Redfern plot. The properties of aged samples were found to decrease due to chain depletion. However, the moduli of XSBR and NR/XSBR blends were found to increase owing to the formation of crosslinks upon ageing.     

Dynamic mechanical and thermal properties of physically compatibilized natural rubber/poly(methyl methacrylate) blends by the addition of natural rubber‐graft‐ poly(methyl methacrylate)

The dynamic mechanical and thermal properties of natural rubber/poly (methyl methacrylate) blends (NR/PMMA) with and without the addition of graft copolymer (NR‐g‐PMMA) have been investigated. Dynamic mechanical spectroscopy is used to examine the effect of compatibilizer loading on storage modulus (E′), loss modulus (E″) and loss tangent (tan δ) at different temperatures and at different frequencies. The morphology of the blends indicates that the size of the dispersed phase decreased by the addition of a few percent of the graft copolymer followed by a leveling off at higher concentrations. This is an indication of interfacial saturation. Attempts have been made to correlate morphology with dynamic mechanical properties. Various models have been used to fit the experimental viscoelastic results. Differential scanning calorimetry has been used to analyze the glass‐transition temperatures of the blends. The thermal stability of the blends has been analyzed by thermogravimetry. Compatibilized blends are found to be more thermally stable than uncompatibilized blends. Finally the miscibility and mechanical properties of the blends annealed above T_g are evaluated. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 525–536, 2000     

Compatibilized natural rubber/recycled ethylene-propylene-diene rubber blends by biocompatibilizer

Biocompatibilizer-based refined, bleached, deodorized palm stearin was successfully used as compatibilizer for natural rubber/recycled ethylene–propylene–diene rubber (NR/R-EPDM) blends. It seems effective in improving the state of cure, tensile properties, as well as the swelling resistance and morphology of the blends, indicating an improvement in compatibility between the NR matrix and R-EPDM rendered by biocompatibilizer. This was clearly verified by the dynamic mechanical properties of the blends. The dynamic responses obtained were clearly corresponding to the swelling result. It proves that the cross-link density plays a major role in the changes of storage modulus and degree of entanglement.     

The effect of mercapto- and thioacetate-modified EPDM on the curing parameters and mechanical properties of natural rubber/EPDM blends

The vulcanization characteristics of natural rubber (NR)/ethylene-propylene-ethylidenenorbornene (EPDM) rubber blends were studied in the presence of thioacetate-(EPDMTA) or mercapto-modified EPDM (EPDMSH), using oscillating disk rheometer. The effect of both functionalized EPDMs was investigated in unaccelerated-sulfur curing system and accelerated-sulfur curing systems containing 0.4 and 0.8 phr of MBTS. Both EPDMTA and EPDMSH act as accelerator agent in the curing process, as indicated by the higher values of cure rate index and lower values of activation energy of vulcanization. A substantial increase of the crosslink density has been also observed in EPDMSH-modified blends. Both EPDMTA and EPDMSH resulted in an increase in tensile strength, but the best performance has been achieved with EPDMSH, probably because of the increase of crosslink density associated to the reactive compatibilization promoted by the reaction between mercapto groups and rubber matrix. The best ageing resistance has been observed in EPDMTA-modified blends.     

Radiation effects on SBR–EPDM blends: A correlation with blend morphology

The effect of γ radiation on the morphological and physical properties of Styrene–butadiene rubber (SBR) and Ethylene–propylene–diene monomer (EPDM) blends has been investigated. An attempt has been made to establish a correlation between various parameters like Gordon–Taylor parameter (k), hydrodynamic interaction parameter (Δ[η]_mix), chemical shift factor (b), Charlesby–Pinner parameter (p₀/q₀) and polymer–polymer interaction parameter (χ). The results showed a close dependence of mechanical and physical properties of irradiated blends on these parameters. The probability of spur overlap has been found to increase with the increase in EPDM content in the blends, which in turn results in significant improvement in the mechanical properties of the irradiated SBR–EPDM blends with higher EPDM fraction. The efficiency of four multifunctional acrylates as crosslinking aid for the radiation‐induced vulcanization of SBR–EPDM blend was also studied. The results established lower efficiency of methacrylates over acrylates in the process and indicated that among the crosslinking agents studied trimethylolpropane triacrylate is the most efficient one. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 1676–1689, 2006     

Morphology dependence of crystallization of natural rubber in blends

Crystallization of natural rubber (NR) was investigated in different morphology for NR/styrene butadiene rubber (SBR) blend and NR/polystyrene-(b)-polyisoprene (SI)/polystyrene (PS) blend. A purified NR (PC-TE) was prepared from pale crape via transesterification. In the blends, PC-TE formed various morphologies; that is, matrix phase, island phase and continuous phase with a nano-scale, respectively, in dependence upon the ratio of the rubbers. The crystallization rate of the blends was also significantly associated with the morphology of the rubbers.     

Study of electrical,mechanical, and nanoscale free‐volume properties of NBR and EPDM rubber reinforced by bentonite or kaolin

The effect of Na bentonite, Ca bentonite, and kaolin fillers on the macrostructure and microstructure of acrylonitrile butadiene rubber, ethylene propylene diene rubber, and their blend (50/50) was studied through electrical and mechanical measurements, as well as with positron annihilation lifetime spectroscopy. The real part of permittivity (ε′), dielectric loss (ε″), and the crosslinking density were found to increase with increasing filler content. The increase of crosslinking density of the blend with increasing amount of fillers reflects a decrease in the equilibrium swelling up to 21.50 wt % compared with that of the unfilled blends. The mechanical investigation showed pronounced increase in the tensile strength, and in elongation at break with the addition of up to 21.50 wt % of filler. In addition, comparing between different fillers showed that the reinforcing effect of Na bentonite is more effective than Ca bentonite and kaolin but the physico‐mechanical of Ca bentonite is less than that for kaolin. The positron annihilation lifetime measurements revealed that the free‐volume properties were strongly affected by the amount and type of filler, in particular, the free‐volume fraction was dramatically decreased with increasing filler content. Furthermore, correlations were made between the free‐volume parameters and both electrical and mechanical properties. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 1825–1838, 2009     

Raman spectroscopy and thermal analysis of gum and silica-filled NR/SBR blends prepared from latex system

Natural rubber/styrene-butadiene rubber (NR/SBR) blends, with and without silica, were prepared by co-coagulating the mixture of rubber latices and various amounts of well-dispersed silica suspension. An attempt to predict blend compositions was made using Raman spectroscopy in association with differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA). It was found that the intensity of each Raman characteristic peak was strongly dependent on the blend composition, but there was no significant evolution with the presence of silica. Also, TGA results revealed an improvement in thermal stability of NR/SBR blends with increasing both SBR and silica contents due to the dilution effect. Two distinct glass transition temperatures (T_g) were observed in DSC thermograms of all blends, and their T_g values were independent on both blend composition and silica content. This indicated a physical blend formation, which agreed well with no shifts in Raman peaks of the blends in comparison with those of the individual rubbers. Linear regression with R² quality factor close to 0.99 was achieved when plotting intensity ratio at 1371/1302 cm^?1 versus blend ratios. On the other hand, the peak height ratio and heat capacity ratio from TGA and DSC analysis, respectively, yielded quadratic equations as a function of blend ratios.     

Thermal properties in cured natural rubber/styrene butadiene rubber blends

Blends of natural rubber (NR) and styrene butadiene rubber (SBR) were prepared with sulfur and n-t-butyl-2-benzothiazole sulfonamide (TBBS) as accelerator, varying the amount of each polymer in the blend. Samples were analysed by rheometer curing at 433 K until their maximum torque was reached. The miscibility among the constituent polymers of the cured compounds was studied in a broad range of temperatures by means of differential scanning calorimetry, analyzing the glass transition temperatures of the samples. The specific heat capacity of the compounds was also determined. Thermal diffusivity of the samples was measured in the temperature range from 130 to 400 K with a new device that performs measurements in vacuum. The thermal results are explained on the basis of the structure formed during the vulcanization of the samples considering the variation of the crosslink density of each phase. Finally, a serial thermal conduction model that takes into account the contribution of each phase to the thermal diffusivity was used to fit the experimental results.     

Dynamic vulcanization of reclaimed tire rubber and high density polyethylene blends

Dynamic vulcanization of reclaimed tire rubber (RTR) and HDPE blends was reported. The effect of blend ratio, methods of vulcanization, i.e. sulphur, peroxide, and mixed system and the addition of compatibilizer on mechanical, thermal, and rheological properties were investigated. The blend with highest impact strength was obtained from 50/50 RTR/HDPE vulcanized by sulphur. Increasing the RTR content to more than 50% resulted in a decrease in the impact strength of blend, most likely due to the increasing carbon black content. For tensile strength, the presence of rubber and carbon black, however, unavoidably caused a drop in this property. Comparing among three methods of vulcanization, sulphur system seems to be the most effective method. Results from solvent swelling ratio, glass transition temperatures and viscosity indicated that the sulphur vulcanization created the highest degree of cross-link and filler-matrix interaction in the RTR/HDPE blend. Morphology of the blends was also assessed by scanning electron microscopy (SEM).     

Dynamic mechanical properties of isotactic polypropylene/nitrile rubber blends: Effects of blend ratio,reactive compatibilization,and dynamic vulcanization

The effect of blend ratio and compatibilization on dynamic mechanical properties of PP/NBR blends was investigated at different temperatures. The storage modulus of the blend decreased with increase in rubber content and shows two T_g's indicating the incompatibility of the system. Various composite models have been used to predict the experimental viscoelastic data. The Takayanagi model fit well with the experimental values. The addition of phenolic modified polypropylene (Ph-PP) and maleic modified polypropylene (MA-PP) improved the storage modulus of the blend at lower temperatures. The enhancement in storage modulus was correlated with the change in domain size of dispersed NBR particles. The effect of dynamic vulcanization using sulfur, peroxide, and mixed system on viscoelastic behavior was also studied. Among these peroxide system shows the highest modulus. © 1997 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 35 : 2309–2327, 1997     

Phase behavior and crystallization of a poly(ethylene oxide)/cellulose acetate butyrate blend

The phase behavior of a partially miscible blend of poly(ethylene oxide) (PEO) and cellulose acetate butyrate (CAB) and the crystalline microstructure of PEO in the blend were studied with differential scanning calorimetry (DSC), optical microscopy, and synchrotron small‐angle X‐ray scattering (SAXS) methods. PEO/CAB showed a lower critical solution temperature (LCST) of 168 °C at the critical composition of PEO of 60 wt %. All blend compositions showed a single glass‐transition temperature (T_g) when they were prepared at temperatures lower than the LCST. However, with increasing CAB content, T_g of the blend changed abruptly at 70 wt % CAB; that is, a cusp existed. Below 70 wt % CAB, the change in T_g with blend composition was predicted by the Brau–Kovacs equation, whereas this change was predicted by the Fox equation at higher CAB contents. A gradual but small depression of the melting point of PEO in the blend with an increasing amount of CAB suggested that the PEO/CAB blends exhibited a weak intermolecular interaction. From DSC and SAXS experiments, it was found that amorphous CAB was incorporated into the interlamellar region of PEO for blends with less than 20 wt % CAB, whereas it was segregated to exist in the interfibrillar region in PEO for other blends with larger amounts of CAB. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1673–1681, 2002