Identification and quantification of the volatile constituents in Cnidium monnieri using supercritical fluid extraction followed by GC‐MS

The volatile components of Cnidium monnieri were obtained by supercritical fluid extraction (SFE) and analyzed by GC‐MS (identification and determination of metabolites). The compounds were identified according to their retention times and mass spectra. The effects of different parameters, such as extraction pressure, temperature, dynamic extraction time, flow rate of CO₂, on the SFE of C. monnieri extracts were investigated. A total of 14 compounds of SFE extracts were identified. Osthole (69.52%), bornyl acetate (10.03%), α‐pinene (4.71%), and imperatorin (2.42%) were the major compounds identified in C. monnieri SFE extracts. The quantitation of osthole and imperatorin were then accomplished. The linear calibration ranges were all 5–1000 μg/mL for osthole and imperatorin by GC‐MS analysis. The recovery of osthole and imperatorin were in the range 96.5–101.8%. The LODs for osthole and imperatorin were 1.0 and 0.6 μg/mL, respectively.     

Optimisation and characterisation of marihuana extracts obtained by supercritical fluid extraction and focused ultrasound extraction and retention time locking GC‐MS

The optimisation of focused ultrasound extraction and supercritical fluid extraction of volatile oils and cannabinoids from marihuana has been accomplished by experimental design approach. On the one hand, the focused ultrasound extraction method of volatile compounds and cannabinoids was studied based on the optimisation of cyclohexane and isopropanol solvent mixtures, and the instrumental variables. The optimal working conditions were finally fixed at isopropanol/cyclohexane 1:1 mixture, cycles (3 s^?1), amplitude (80%) and sonication time (5 min). On the other hand, the supercritical fluid extraction method was optimised in order to obtain a deterpenation of the plant and a subsequent cannabinoid extraction. For this purpose, pressure, temperature, flow and co‐solvent percentage were optimised and the optimal working conditions were set at 100 bar, 35°C, 1 mL/min, no co‐solvent for the terpenes and 20% of ethanol for the cannabinoids. Based on the retention time locking GC‐MS analysis of the supercritical fluid extracts the classification of the samples according to the type of plant, the growing area and season was attained. Finally, three monoterpenes and three cannabinoids were quantified in the ranges of 0.006–6.2 μg/g and 0.96–324 mg/g, respectively.     

Sensitive determination of amide herbicides in environmental water samples by a combination of solid‐phase extraction and dispersive liquid–liquid microextraction prior to GC–MS

In this paper, solid‐phase extraction (SPE) in combination with dispersive liquid–liquid microextraction (DLLME) has been developed as a sample pretreatment method with high enrichment factors for the sensitive determination of amide herbicides in water samples. In SPE–DLLME, amide herbicides were adsorbed quantitatively from a large volume of aqueous samples (100 mL) onto a multiwalled carbon nanotube adsorbent (100 mg). After elution of the target compounds from the adsorbent with acetone, the DLLME technique was performed on the resulting solution. Finally, the analytes in the extraction solvent were determined by gas chromatography–mass spectrometry. Some important extraction parameters, such as flow rate of sample, breakthrough volume, sample pH, type and volume of the elution solvent, as well as salt addition, were studied and optimized in detail. Under optimum conditions, high enrichment factors ranging from 6593 to 7873 were achieved in less than 10 min. There was linearity over the range of 0.01–10 μg/L with relative standard deviations of 2.6–8.7%. The limits of detection ranged from 0.002 to 0.006 μg/L. The proposed method was used for the analysis of water samples, and satisfactory results were achieved.     

Screening for inherited metabolic diseases using gas chromatography–tandem mass spectrometry (GC–MS/MS) in Sichuan,China

The aim of this study was to retrospectively diagnose and confirm inherited metabolic diseases (IMD), from a small population of IMD high‐risk patients, with the aid of gas chromatography–tandem mass spectrometry (GC–MS/MS), technologies yet to be popularized in Sichuan, China. Using GC–MS/MS coupled with clinical diagnosis, we retrospectively analyzed samples of dried blood spots and urine specimen from 183 IMD high‐risk infant patients, who visited the West China Second Hospital of Sichuan University between June 2013 and October 2015. Four out of 183 IMD high‐risk infant patients were finally diagnosed to be IMD positive, among which two patients were identified with phenylketonuria, one with maple syrup urine disease, and 1 with methylmalonic academia. Restrictive diets and other symptomatic treatments were employed to treat the confirmed infant patients whose conditions are still under tracking and there are zero cases of death so far. GC–MS/MS was found to be an efficient and reliable way to detect IMD. It is necessary to apply GC–MS/MS, in addition to other clinical approaches, for diagnosing candidate IMD patients so that the confirmed patients can get medical intervention and timely treatment.     

Analytical supercritical fluid extraction of Chinese herbal medicines

Summary An analytical supercritical fluid extraction (SFE) technique, followed by GC/MS, was developed to separate and determine the volatile components in Chinese herbal medicine. Three kinds of herbs, frankincense, myrrh, andEvodia rutaecarpa were extracted and analyzed. The extraction was carried out using supercritical fluid CO₂ at 20 MPa and 50°C. The main factors affecting the efficiency and selectivity of the extraction are discussed. The results revealed the potential of supercritical fluid extraction as an analytical procedure for the study of medicinal plants.     

Liquid–solid disk extraction followed by supercritical fluid elution and gas chromatography of phenols from water

A method combining the techniques of liquid – solid disk extraction (LSDE) and supercritical fluid elution (SFE) has been developed for the phenols regulated by the Clean Water Act. LSDE uses a disk or membrane made of polytetrafluoroethylene (PTFE) fibrils impregnated with small particles, e.g. styrene divinylbenzene (SDB) resin, to extract phenols from water. After disk extraction the retained analytes are eluted from the disk using SFE. SFE is used as an alternative to liquid solvent elution with an organic solvent. Analytes are separated, identified, and quantified using gas chromatography – ion trap detector mass spectrometry (GC-ITDMS). The method is capable of sub parts per billion detection limits, and precision of 5–28% RSD. Evaluation of various disks or membranes, such as C₁₈-silica disks, SDB disks, and ion exchange membranes, has also been performed for the extraction of phenols from water. The results obtained from the in-situ aqueous acetylation of phenols and extraction of their acetates are quantitative. The utilization of LSDE and SFE techniques has proven to be a more effective approach than liquid – liquid extraction in minimizing air pollution and solvent waste.     

Simultaneous determination of trace migration of phthalate esters in honey and royal jelly by GC–MS

A simple, rapid, and reliable liquid–liquid extraction coupled to GC–MS method was developed and validated for the quantification of 22 phthalate esters (PAEs) in honey and royal jelly. Instrument parameters for GC–MS were tested to obtain the satisfactory separation between 22 PAEs with high sensitivity. The extraction procedure was optimized in order to achieve the best recovery. The following criteria were used to validate the developed method: linearity, LOD, lower LOQ, precision, accuracy, matrix effect and carry‐over. Correlation coefficients were >0.999 by applying the linear regression model based on the least‐squares method with a weighting factor (1/x). The intra‐ and interday precision were within 12.7% in terms of RSD, and the accuracy was within ?11.8% in terms of relative error. The mean extraction recoveries ranged between 80.1 and 110.9% for honey and royal jelly. No significant matrix effect and carry‐over for PAEs were observed for the analysis of honey and royal jelly samples. A total of 20 real samples were analyzed for a mini‐survey using the developed method. Seven PAEs in honey samples and five PAEs in royal jelly samples were found, indicating potential contamination with several PAEs.     

Supercritical fluid extraction of kava lactones from Piper methysticum (kava) herb

Supercritical fluid extraction of kava lactones from Piper methysticum Forst. herb is described here. The extraction was performed with supercritical carbon dioxide alone and supercritical carbon dioxide modified with 15% ethanol, and the extracts were analyzed by gas chromatography/mass spectrometry. Seven lactones including: 7,8-dihydrokavain; kavain; 5,6-dehydrokavain; 5, 6, 7, 8-tetrahydroyangonin; dihydromethysticin; yangonin; and methysticin were the major constituents in the SFE extract.     

Indirect hydrogen analysis by gas chromatography coupled to mass spectrometry (GC–MS)

Gas chromatography (GC) is an analytical tool very useful to investigate the composition of gaseous mixtures. The different gases are separated by specific columns but, if hydrogen (H₂) is present in the sample, its detection can be performed by a thermal conductivity detector or a helium ionization detector. Indeed, coupled to GC, no other detector can perform this detection except the expensive atomic emission detector. Based on the detection and analysis of H₂ isotopes by low‐pressure chemical ionization mass spectrometry (MS), a new method for H₂ detection by GC coupled to MS with an electron ionization ion source and a quadrupole analyser is presented. The presence of H₂ in a gaseous mixture could easily be put in evidence by the monitoring of the molecular ion of the protonated carrier gas. Copyright © 2013 John Wiley & Sons, Ltd.     

Enrichment of the thymoquinone content in volatile oil from Satureja montana using supercritical fluid extraction

Supercritical fluid extraction (SFE) of the volatile oil from Satureja montana L. was performed under different conditions of pressure (90 and 100 bar), temperature (40 and 50°C), mean particle sizes (0.4, 0.6 and 0.8 mm) and CO₂ flow rate (0.8, 1.1 and 1.3 kg/h) to understand the influence of these parameters on the composition and yield of this oil. The results were compared with those obtained for the essential oil isolated by hydrodistillation (HD). The volatile and the essential oil were analysed by GC and GC‐MS. The main compounds are carvacrol (52.2–62.0% for HD vs. 41.7–64.5% for SFE), thymol (8.6–11.0% for HD vs. 6.0–11.3% for SFE), p‐cymene (6.9–12.8% for HD vs. 6.0–17.8% for SFE), γ‐terpinene (6.4–9.4% for HD vs. 2.3–6.0% for SFE) and β‐bisabolene (2.0–2.7% for HD vs. 2.2–3.5% for SFE). The major difference between SFE and HD was the relative amount of thymoquinone, an oxygenated monoterpene with important biological activities, which can be ten‐fold higher in volatile oil (1.6–3.0 for SFE vs. 0.2% for HD). The morphology of the glandular trichomes of S. montana and the effect of the grinding process on them was also evaluated by SEM.     

Comparative analysis of essential oils from eight herbal medicines with pungent flavor and cool nature by GC–MS and chemometric resolution methods

Systematic comparative research was conducted on essential oils from eight traditional Chinese medicines (TCM) of pungent flavor and cool nature because the essential oils are the main active ingredients of herbs of this kind. The work was based on their component analysis by gas chromatography–mass spectrometry (GC–MS), on their retention indices, as well as on chemometric resolution methods. A total of 144 compounds were tentatively identified, accounting for 69.0% to 91.8% of the total essential oils. It is worth noting that there are 67 compounds in at least three of these eight essential oils. Moreover, many biologically active compounds, such as hexanal, α‐pinene, camphene, β‐pinene, p‐cymene, limonene, eucalyptol, (Z)‐ocimene, γ‐terpinene, camphor, p‐menthone, 4‐terpineol, α‐terpineol, carvone, eugenol, caryophyllene, β‐farnesene, α‐curcumene, β‐selinene, δ‐cadinene, caryophyllene oxide, cedrol, n‐hexadecanoic acid, benzaldehyde, benzeneacetaldehyde, phthalic acid diisobutyl ester, linoleic acid, tetradecanoic acid, (Z,Z,Z)‐9,12,15‐octadecatrienoic acid, eucalyptol, pentadecanoic acid, hexadecanoic acid methyl ester, linoleic acid methyl ester, exist in at least four of the eight essential oils. These results might help us to understand why the eight herbs are all of pungent flavor and cool nature according to the theory of TCM, and may provide a useful chemical basis for future research on herbs of this kind.     

Analysis of volatiles in polymers,part II. Supercritical fluid extraction/open tubular GC/MS

Summary Supercritical fluid extraction (SFE) connected to open tubular gas chromatography has been used for the analysis of non-polar to medium polar volatiles entrained in polymers. This polymer sheets, prepared with the aid of a microtome, have been extracted with supercritical carbon dioxide. The influence of sample area/weight ratio and extraction cell volume on the SFE performance has been investigated. Further, quantitative analysis was executed by stepwise extractions.A set of polybutylene terephthalate polymers, originating from different manufactures, has been analysed regarding entrained volatiles.     

Method validation and determination of lisdexamfetamine and amphetamine in oral fluid,plasma and urine by LC–MS/MS

Lisdexamfetamine (LDX) is a long‐acting prodrug stimulant indicated for the treatment of attention‐deficit/hyperactivity disorder and binge‐eating disorder symptoms. In vivo hydrolysis of LDX amide bond releases the therapeutically active d ‐amphetamine (d ‐AMPH). Since toxicological tests in biological samples can detect AMPH from the use of some legal medications, efficient methods are needed in order to correctly interpret the results. The aim of this study was to develop and validate an LC–MS/MS method for the simultaneous quantification of LDX and its main biotransformation product AMPH in human oral fluid, plasma and urine. Calibration curve range for both analytes was 1–128 ng/mL in oral fluid and plasma and 4–256 ng/mL in urine, being the lowest concentration the limit of quantification. Accuracy of the determined values of the target analytes for the five control levels ranged from 94.8 to 111.7% for oral fluid, from 91.3 to 100.2% for plasma and from 94.8 to 109.8% for urine. Imprecision for the five control levels did not exceeded 12.8% for oral fluid, 16.2% for plasma and 17.1% for urine. The method developed for the three matrices was validated and was also successfully applied to assess real samples, showing for the first time the detection of LDX in oral fluid.     

Discovery of false identification using similarity difference in GC–MS‐based metabolomics

Compound identification is a critical process in metabolomics. The widely used approach for compound identification in gas chromatography–mass spectrometry‐based metabolomics is spectrum matching, in which the mass spectral similarity between an experimental mass spectrum and each mass spectrum in a reference library is calculated. While various similarity measures have been developed to improve the overall accuracy of compound identification, little attention has been paid to reducing the false discovery rate. We, therefore, develop an approach for controlling the false identification rate using the distribution of the difference between the first and second highest spectral similarity scores. We further propose a model‐based approach to achieving a desired true positive rate. The developed method is applied to the National Institute of Standards and Technology mass spectral library, and its performance is compared with that of the conventional approach that uses only the maximum spectral similarity score. The results show that the developed method achieves a significantly higher F1 score and positive predictive value than did the conventional approach. Copyright © 2014 John Wiley & Sons, Ltd.     

Quantitative analysis of polymer additives in low density polyethylene using supercritical fluid extraction/supercritical fluid chromatography

Analysis of low concentration polymer additives has been a challenging problem. The commonly used methods of analysis involve the initial extraction of polymer additives with solvents, often in a Soxhlet apparatus, followed by liquid, size exclusion, or gas chromatography. This paper describes the on-line super-critical fluid extraction (SFE)-supercritical fluid chromatographic (SFC) determination of different additives from low density polyethylene. Cryogenic collection was used as an interface between SFE and SFC to focus the extraction eluate before transfer to an analytical SFC column for quantitative analysis.     

Superheated water extraction, steam distillation and Soxhlet extraction of essential oils of Origanum onites

Superheated water extraction (SWE) at various temperatures (100, 125, 150 and 175°C), steam distillation, and Soxhlet extraction were compared in the extraction of essential oils from two samples of the plant Origanum onites, one cultivated, the other wild. C18 solid-phase extraction was used to elute the essential oils from the SWE aqueous extract. The compositions of the extracted essential oils obtained from all three methods were then characterized by comprehensive GC×GC/time-of-flight mass spectrometry (TOF/MS). The highest essential oil yields were obtained by using SWE at 150°C with a flow rate of 2 mL min^–1 and a pressure of 60 bar for 30 min: these were 3.76 and 4.11% for wild and cultivated O. onites samples, respectively, expressed as a percentage of 100 g of dry (leaf) matter. The yields obtained using SWE at 150°C were slightly higher than those from conventional methods. Steam distillation was performed for 3 h, and Soxhlet extraction was completed in 12 h. The major compounds found were borneol, terpinen-4-ol and carvacrol.     

Resolving overlapping GC–MS signals with a multistep screening chemometric approach for the fast determination of pesticides

For the rapid analysis of multicomponent mixtures using GC–MS, a chemometric multistep screening approach was proposed to extract the signals of the components from the overlapping signals measured with a very fast temperature program. At first, independent component analysis was used to find all the possible mass spectra from the overlapping signal in the moving windows along the retention time, and iterative target transformation factor analysis was employed to validate the existence of the extracted spectra from each window. Then, identical signals in the validated spectra were excluded using match ratio as a criterion. Finally, the chromatographic profiles for each spectrum were calculated using non‐negative immune algorithm, and the spectra with a reasonable profile were taken as the identified components. A mixture of 53 pesticides was analyzed with a very fast temperature program of 7 min. A total of 48 pesticides and 16 interferences were identified from the overlapping GC–MS signal.