Temperature‐sensitive chitosan membranes as a substrate for cell adhesion and cell sheet detachment

A series of temperature‐sensitive poly(CSA‐co‐NIPAAm) membranes that were suitable for cell culture and confluent cell sheets detachment were prepared. The membranes with thermo‐responsive surface properties were synthesized by the copolymerization of acrylic acid‐derivatized chitosan (CSA) and N‐isopropylacrylamide (NIPAAm) in aqueous solution. Characterization of the membranes were carried out by means of the Fourier transform infrared (FTIR), X‐ray photoelectron spectroscopy (XPS), scanning electron microscope (SEM), and water contact‐angle (WCA) measurements. The adhesion and detachment of mouse fibroblast (L929) cells on these membranes have been investigated. The study showed that poly(CSA‐co‐NIPAAm) membranes could not only enhance fibroblasts attachment but also harvest confluent cell sheets by simply lowering the temperature. Furthermore, the detached cells retained high viability and could proliferate again after transferred to a new culture surface. Copyright © 2011 John Wiley & Sons, Ltd.     

Electrospun fiber mats of poly(3‐hydroxybutyrate), poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate), and their blends

Electrospinning of poly(3‐hydroxybutyrate) (PHB), poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) (PHBV), and their blends was first carried out in chloroform at 50 °C on a stationary collector. The average diameter of the as‐spun fiber from PHB and PHBV solutions decreased with increasing collection distance and increased with increasing solution concentration and applied electrical potential. In all of the spinning conditions investigated, the average diameter of the as‐spun pure fibers ranged between 1.6 and 8.8 μm. Electrospinning of PHB, PHBV, and their blends was carried out further at a fixed solution concentration of 14% w/v on a homemade rotating cylindrical collector. Well‐aligned, cross‐sectionally round fibers without beads were obtained. The average diameter of the as‐spun pure and blend fibers ranged between 2.3 and 4.0 μm. The as‐spun fiber mats appeared to be more hydrophobic than the corresponding films and much improvement in the tensile strength and the elongation at break was observed for the blend fiber mats over those of the pure fiber ones. Lastly, indirect cytotoxicity evaluation of the as‐spun pure and blend fiber mats with mouse fibroblasts (L929) indicated that these mats posed no threat to the cells. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 2923–2933, 2006     

Fabrication and optimization of proton conductive polybenzimidazole electrospun nanofiber membranes

Phosphoric acid (PA)–doped polybenzimidazole (PBI) proton exchange membranes have received attention because of their good mechanical properties, moderate gas permeability, and superior proton conductivity under high temperature operation. Among PBI‐based film membranes, nanofibrous membranes withstand to higher strain because of strongly oriented polymer chains while exhibiting higher specific surface area with increased number of proton‐conducting sites. In this study, PBI electrospun nanofibers were produced and doped with PA to operate as high temperature proton exchange membrane, while changes in proton conductivity and morphologies were monitored. Proton conductive PBI nanofiber membranes by using the process parameters of 15 kV and 100 μL/h at 15 wt% PBI/dimethylacetamide polymer concentration were prepared by varying PA doping time as 24, 48, 72, and 96 hours. The morphological changes associated with PA doping addressed that acid doping significantly caused swelling and 2‐fold increase in mean fiber diameter. Tensile strength of the membranes is found to be increased by doping level, whereas the strain at break (15%) decreased because of the brittle nature of H‐bond network. 72 hour doped PBI membranes demonstrated highest proton conductivity whereas the decrease on conductivity for 96‐hour doped PBI membranes, which could be attributed to the morphological changes due to H‐bond network and acid leaking, was noted. Overall, the results suggested that of 72‐hour doped PBI membranes with proton conductivity of 123 mS/cm could be a potential candidate for proton exchange membrane fuel cell.     

Comparison of random and gradient amino functionalized poly(2‐oxazoline)s: Can the transfection efficiency be tuned by the macromolecular structure?

Poly(ethylene imine) can be considered as the gold standard for DNA delivery into cells in vitro, but severe cytotoxic side‐effects and inapplicability for targeted approaches in vivo urgently call for the design of new gene carriers. Since poly(2‐oxazoline)s (P(Ox)s) can be easily synthesized and modified, this polymer class might be ideal for the optimization of polymeric transfection processes. The utilization of 2‐methyl‐2‐oxazoline (MeOx) and 2‐ethyl‐2‐oxazoline (EtOx) is also known to be beneficial because these monomers were suggested to overcome solubility issues, mediate stealth behavior and, consequently, facilitate a reduction of cytotoxicity. A series of amino (AmOx) functionalized P(Ox) copolymers with either MeOx (gradient copolymers) or EtOx (random copolymers) was synthesized, deprotected and biochemically characterized regarding cytotoxicity, polyplex formation ability, cellular uptake, and transfection efficiency. Polymers with percentages of AmOx higher than 35 mol % showed stable polyplex formation and also an increase in cytotoxicity. All elucidated P(Ox)s revealed a poor transfection efficiency in both L929 and Hepa1‐6 cell lines. However, the investigations contribute to the understanding of the influence of stealth units (MeOx and EtOx) and their distribution within the polymer chain on selected properties of polyplexes and describe characteristics of amino functionalized P(Ox)s in different cell lines. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 1210–1224     

Functionalization of Biodegradable Polyester for Tissue Engineering Applications

Summary: Chemical modification of polymer surface may potentially be used to create smart materials that can guide cellular adhesion, proliferation and maintenance of specific expression of molecules. The microbial polyester poly (3-hydroxybutyrate) (PHB) has been attracted attention as promising material for applications in tissue engineering. In this work, a wet-chemical method, base ethylenediamine aminolysis, was performed to improve the adhesion of chondrocytes isolated from human articular cartilage to PHB films. The effects of chemical treatment on PHB films was evaluated by following changes in morphology and surface chemical composition using atomic force microscopy (AFM) and X-ray photoelectron spectroscopy (XPS), respectively. While the effect on cells morphology was studied by scanning electron microscopy (SEM). The treatment with ethylenediamine did not change significantly the morphology of the structures of PHB films surface. However, the roughness of the aminolyzed films was slightly higher. The introduction of nitrogen-containing groups was confirmed by XPS. In vitro experiments indicated that the surface modification did not have toxic effects in cells, since they could adhere and proliferate on modified PHB films. It was observed that long-time treatment improved ability of PHB films to support cell growth, which could be accounted to physicochemical and topological effects.     

Microbial production of polyhydroxyalkanoates by bacteria isolated from oil wastes

A Gram-positive coccus-shaped bacterium capable of synthesizing higher relative molecular weight (M _r), polyhydroxybutyrate (PHB) was isolated from sesame oil and identified as Staphylococcus epidermidis (by Microbial ID, Inc., Newark, NJ). The experiment was conducted by shake flask fermentation culture using media containing fructose. Cell growth up to a dry mass of 2.5 g/L and PHB accumulation up to 15.02% of cell dry wt was observed. Apart from using single carbohydrate as a sole carbon source, various industrial food wastes including sesame oil, ice cream, malt, and soya wastes were investigated as nutrients for S. epidermidis to reduce the cost of the carbon source. As a result, we found that by using malt wastes as nutrient for cell growth, PHB accumulation of S. epidermidis was much better than using other wastes as nutrient source. The final dried cell mass and PHB production using malt wastes were 1.76 g/L and 6.93% polymer/cells (grams/gram), and 3.5 g/L and 3.31% polymer/cells (grams/gram) in shake flask culture and in fermentor culture, respectively. The bacterial polymer was characterized by ¹H-nuclear magnetic resonance (NMR), ¹³C-NMR, Fourier transform infrared, and differential scanning calorimetry. The results show that with different industrial food wastes as carbon and energy sources, the same biopolymer (PHB) was obtained. However, the use of sesame oil as the carbon source resulted in the accumulation of PHB with a higher melting point than that produced from other food wastes as carbon sources by this organism under similar experimental conditions.     

Wound Healing Attributes of Polyelectrolyte Multilayers Prepared with Multi‐l‐arginyl‐poly‐l‐aspartate Pairing with Hyaluronic Acid and γ‐Polyglutamic Acid

Biodegradable multi‐l ‐arginyl‐poly‐l ‐aspartate (MAPA), more commonly cyanophycin, prepared with recombinant Escherichia coli contains a polyaspartate backbone with lysine and arginine as side chains. Two assemblies of polyelectrolyte multilayers (PEMs) are fabricated at three different concentration ratios of insoluble MAPA (iMAPA) with hyaluronic acid (iMAPA/HA) and with γ‐polyglutamic acid (iMAPA/γ‐PGA), respectively, utilizing a layer‐by‐layer approach. Both films with iMAPA and its counterpart, HA or γ‐PGA, as the terminal layer are prepared to assess the effect on film roughness, cell growth, and cell migration. iMAPA incorporation is higher for a higher concentration of the anionic polymer due to better charge interaction. The iMAPA/HA films when compared to iMAPA/γ‐PGA multilayers show least roughness. The growth rates of L929 fibroblast cells on the PEMs are similar to those on glass substrate, with no supplementary effect of the terminal layer. However, the migration rates of L929 cells increase for all PEMs. γ‐PGA incorporated films impart 50% enhancement to the cell migration after 12 h of culture as compared to the untreated glass, and the smooth films containing HA display a maximum 82% improvement. The results present the use of iMAPA to construct a new layer‐by‐layer system of polyelectrolyte biopolymers with a potential application in wound dressing.     

Comparison of surface segregation and anticoagulant property in block copolymer blended evaporation and phase inversion membranes

In our recent study, an ABA amphiphilic triblock copolymer poly(vinyl pyrrolidone)‐b‐poly(methyl methacrylate)‐b‐poly(vinyl pyrrolidone) (PVP‐b‐PMMA‐b‐PVP) was synthesized and directly blended with polyethersulfone (PES) to prepare membranes. To further investigate the effects of surface energy and miscibility on the near‐surface composition profile of the membranes, evaporation membrane and phase inversion membrane of PES/PVP‐b‐PMMA‐b‐PVP were prepared by evaporating the solvent in a vacuum oven, and by a liquid–liquid phase separation technique, respectively. The surface composition and morphology of the membranes were investigated using XPS and tapping mode atomic force microscopy, and the surface segregations of the membranes were compared and discussed. For the evaporation membrane, PVP blocks were buried below the lower surface energy PMMA blocks and PES substrate at the airside surface. For the phase inversion membrane, however, the hydrophilicity of PVP blocks were the biggest driving force because of the high speed exchange between water and solvent, and present at the membrane surface. Thus, the modified PES membrane prepared by using phase inversion method has a layer of PVP block brushes on its surface and has the better anticoagulant property, which might improve the blood compatibility of the membrane and has potential to be used in blood purification. Copyright © 2012 John Wiley & Sons, Ltd.     

Original method of imprinting pores in scaffolds for tissue engineering

Results of the preparation of biodegradable porous scaffolds using an original modification of a wet phase inversion method were presented. Influence of gelatin non‐woven as a non‐classic pore precursor and polyvinylpyrrolidone, Pluronic as classic pore precursors on the structure of obtained scaffolds was analyzed. It was shown that the addition of gelatin non‐wovens enables the preparation of scaffolds, which allow for the growth of cells (size, distribution, and shape of pores). Mechanical properties of the obtained cell scaffolds were determined. The influence of pore precursors on mass absorption of scaffolds against isopropanol and plasma was investigated. Interaction of scaffolds with a T‐lymphocyte line (Jurkat) and with fibroblasts (L929) was investigated. Obtained scaffolds are not cytotoxic and can be used as implants, for example, the regeneration of cartilage tissue.     

Two‐stage phase separation of cellulose acetate membranes modified with plasma‐treated natural zeolite: Response surface modeling

Cellulose acetate (CA) microfiltration membranes were prepared by two‐stage vapor‐induced phase separation (VIPS) and immersion precipitation. To improve the hydrophilicity and permeability of the membranes at low operating pressures, plasma‐treated natural zeolite was incorporated into the membranes. A response surface methodology based on the three‐level central composite design (CCD) was used to model and optimize the casting solution composition of the membranes with the aim of maximizing membranes permeability. Three independent variables for CCD optimization were concentration of CA, polyvinylpyrrolidone (PVP) pore former, and plasma‐treated zeolite additive. The results showed that a second‐order polynomial model could properly predict the response (pure water flux) at any input variable values with a satisfying determination coefficient (R²) of 0.954. Also, analysis of variance (ANOVA) confirmed the adequacy of the obtained model. The permeability of the prepared membranes increased by increasing zeolite loading from 0.10 to 0.50 wt%, which was related to the membranes morphology and porosity and confirmed by scanning electron microscopy (SEM) images. Pure water flux of the membranes decreased by increasing CA concentration while an optimum PVP amount was required to reach the maximum flux. The result of the bubble point analysis well matched with surface SEM images of the membranes and permeability trend predicted by CCD model. Also, the prepared CA membranes with different compositions showed no toxicity for mouse L929 fibroblast, which indicated their nontoxic and biocompatible nature.     

Biomedical Investigations of Biodegradable PHAs

This work is a review of the results of biomedical studies of polymer devices (films, fibers, microparticles, 3D implants) made from resorbable PHAs synthesized by the bacterium Wautersia (Ralstonia) eutropha B5786, using the technology developed at the Institute of Biophysics of the Siberian Branch of the Russian Academy of Sciences. Two types of PHAs – polyhydroxybutyrate (PHB) and a hydroxybutyrate/hydroxyvalerate copolymer (PHB/PHV) – have been proven to be biocompatible in vitro in cultures of fibroblasts, endothelial cells, hepatocytes, and osteoblasts, and in short- and long-duration experiments on animals. Polymer films and membranes have been found to be usable as scaffolds for functioning cells and monofilament suture fibers – for stitching muscular-fascial wounds and in abdominal surgery. Ectopic bone formation assay and experiments with the model of segmental osteotomy showed that 3D PHB and PHB/HA implants can be used for reparative osteogenesis. The paper reports beneficial results of using polymers to repair bone defects in oral surgery.     

Preparation of chitosan–silica/PCL composite membrane as wound dressing with enhanced cell attachment

In the present study, the asymmetrical polycaprolactone membranes were synthesized using phase inversion method and modified by addition of Pluronic (F‐127) and sodium hydroxide treatment to improve the cell attachment. The chemical structure, physical properties and mechanical behavior of the membranes as well as cell attachment and proliferation on them were characterized and compared to determine the appropriate membrane used in wound dressing fabrication. Then, a composite membrane as wound dressing capable of drug controlled‐release was prepared composed of two merged layers: an asymmetrical poly(ε‐caprolactone) layer coated with a drug‐loaded chitosan – silica matrix. Drug release behavior and biocompatibility of the final system were evaluated. The results showed that the polycaprolactone modified membrane provides appropriate properties to expand fibroblast cell adhesion and proliferation. This in‐vitro study also showed that the controlled‐release composite wound dressing was developed with approximately 70% cumulative release rate, which provided a porous substrate to support skin cells. Copyright © 2017 John Wiley & Sons, Ltd.     

Poly(acrylonitrile) ultrafiltration membranes. II. Membrane morphology and permeation characteristics

The rheology and phase‐boundary characteristics of various solutions comprising three polyacrylonitrile (PAN) grades dissolved in solutions of N,N‐dimethylformamide + salt (LiCl, ZnCl₂, or AlCl₃) additives were correlated with the resulting membrane morphology as determined by microscopy and permeability measurements. The phase separation characteristics of the dope solution were not markedly affected by the PAN molecular weight (MW); however, they were affected by the salt additive. For higher MW grades, the effect of salt addition can also be masked by the increased self‐association tendency of the polymer chains. PAN‐B and ‐C membranes were clearly less asymmetric in structure than the lower MW PAN‐A–based membranes. This is attributed to the higher viscosity/lower diffusivity of the PAN‐B and ‐C solutions, which results in slower solvent–nonsolvent exchange during the phase inversion process. Two factors reduce the incidence of surface defects (increased bubble points): (a) higher solution viscosity dampens surface perturbations during phase inversion, and (b) phase inversion pathways resulting in more homogenous morphology lead to membranes with higher bubble points. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 2074–2085, 2005     

High throughput study of phase inversion parameters for polyimide-based SRNF membranes

High throughput (HT) techniques were applied for the first time for a detailed study of parameters involved in a phase inversion process. The synthesis of integrally skinned asymmetric polyimide (Matrimid^®) membranes was investigated. In spite of being one of the most important materials of reference in solvent resistant nanofiltration (SRNF), a detailed study of the phase inversion parameters for this system is still missing. Phase inversion parameters were selected both on the level of the composition of the casting solution (polymer concentration, solvent type, co-solvent/solvent weight ratio, non-solvent content) as on the level of the post-casting (evaporation time) and immersion (composition coagulation medium) conditions. The study of this extensive parameter space was conducted in a HT-fashion, in which the entire membrane preparation and testing process was miniaturized, parallellized and automated. Thanks to the availability of reliable HT techniques at all levels (i.e. preparation of polymer solutions, membrane casting and membrane testing), 145 membranes were prepared and tested (in triplicate) in the separation of the dye rose Bengal from 2-propanol within a time frame of a few months, meaning a dramatic improvement in time- and cost-efficiency. An attempt was made to link the SRNF performances of the prepared membranes and their SEM-observed morphologies more fundamentally to the phase inversion parameters through the use of Hansen solubility parameters and viscosity measurements.     

Synthesis and Characterization of Aminoporphyrin‐End‐Functionalized Poly(N‐isopropylacrylamide) with Photodynamic and Thermoresponsive Effects

The novel aminoporphyrin‐end‐functionalized poly(N‐isopropylacrylamide) (PNIPAM) polymer H₂N‐TPP‐PNIPAM (TPP=5,10,15,20‐tetraphenyl‐21H,23H‐porphyrin) behaves as a multifunctional platform that displays a photodynamic effect, thermosensitivity, and fluorescence properties. The polymer was designed by using an asymmetrical aminoporphyrin (i.e., H₂N‐TPP‐Cl) as the initiator for the atom‐transfer radical polymerization of N‐isopropylacrylamide (NIPAM). The polydispersity index (PDI) obtained by gel‐permeation chromatography indicated that the molecular‐weight distribution was narrow (1.09<PDI<1.27). The lower critical solution temperatures of H₂N‐TPP‐PNIPAM showed a decreasing trend as the molecular weight was increased as a result of the incorporation of the porphyrin group at the end of the chain. The fluorescence spectra revealed the luminescent properties of the materials. The results of confocal laser scanning microscopy showed that the polymer could enter the cytoplasm through endocytosis. In addition, the multifunctional platform exhibited low toxicity against normal cells (L929) and cancer cells (Hela) and enhanced photodynamic activity towards HeLa cells, without significant necrocytosis towards L929 cells; as a result this material may be useful in the future for practical photodynamic therapy.     

Molecularly imprinted polymer on a SiO2‐coated graphene oxide surface for the fast and selective dispersive solid‐phase extraction of Carbamazepine from biological samples

A surface carbamazepine‐imprinted polymer was grafted and synthesized on the SiO₂/graphene oxide surface. Firstly SiO₂ was coated on synthesized graphene oxide sheet using the sol–gel technique. Prior to polymerization, the vinyl group was incorporated on to the surface of SiO₂/graphene oxide to direct selective polymerization on the surface. Methacrylic acid, ethylene glycol dimethacrylate and ethanol were used as monomer, cross‐linker and porogen, respectively. Nonimprinted polymer was also prepared for comparison. The properties of the molecularly imprinted polymer were characterized using field‐emission scanning electron microscopy and Fourier‐transform infrared spectroscopy. The surface molecularly imprinted polymer was utilized as an adsorbent of dispersive solid‐phase extraction for separation and preconcentration of carbamazepine. The effects of the different parameters influencing the extraction efficiency, such as sample pH were investigated and optimized. The specificity of the molecular imprinted polymer over the nonimprinted polymer was examined in absence and presence of competitive drugs. The carbamazepine calibration curve showed linearity in the ranges 0.5–500 μg/L. The limits of detection and quantification under the optimized conditions were 0.1 and 0.3 μg/L, respectively. The within‐day and between‐day relative standard deviations (n = 3) were 3.6 and 4.3%, respectively. Furthermore, the relative recoveries for spiked biological samples were above 85%.     

One‐step synthesis of polymer micro‐tubes tethered by polymer nanowire networks via RAFT polymerization of N,N′‐methylene bisacrylamide xerogel fibers in toluene and ethanol mixed solution

In the mixed solution of toluene and ethanol, polymer micro‐tubes (PMTs) tethered by polymer nanowire networks (PTPWNs) were fabricated facilely via one‐step reversible addition fragmentation chain transfer (RAFT) polymerization by taking N,N′‐methylene bisacrylamide (MBA) xerogel fibers as both template and monomer source. The products were analyzed by FTIR, SEM, TEM, surface area and porosity analyzer, and contact angle tester. The results indicated that PTPWNs were obtained as the sole product at ethanol content of 1.0 wt %. As the content of ethanol increases from 0 to 1.0 wt %, the specific surface area of the products became higher, indicating more polymer nanowire networks (PWNs) on the tubes. At ethanol contents of 1.5 wt % and 2.0 wt %, some particles were also obtained besides PTPWNs. The formation process of PTPWNs was studied by analyzing the products obtained at different reaction time. The results revealed that PTPWNs were formed by two steps, PMTs were formed quickly and then PWNs formed in the solution tethered to the tubes. Moreover, the effect of RAFT agent on the morphologies of the products revealed that PTPWNs could be obtained via RAFT polymerization at suitable dosage of RAFT agent, while polymer particles were generated via conventional free radical polymerization. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 1862–1868     

Synthesis of self‐assembled sphingolipid conjugates and their morphology effect on anticancer therapeutic potency

The shape of self‐assembling polymer–drug conjugates, influencing the cellular uptake, is one of the important factors to be considered for effective drug delivery. In this study, we described synthesis of polymeric drug conjugates of different morphologies with phytosphingosine (PHS) as a hydrophobic model drug and poly(amino acid) as a hydrophilic host polymer. By varying the amount of PHS grafted to poly(amino acid), PHS–poly(amino acid) conjugates exhibited morphological transition from spherical to worm‐like micellar aggregates in the aqueous media. We investigated the physicochemical properties of self‐assembled structures in terms of hydrodynamic size, surface charge, and critical aggregation concentration. The anticancer therapeutic potency of these self‐assembled structures was also discussed in terms of cellular uptake and cytotoxicity of prodrug micelles as a function of dose and time by in vitro cell study. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Preparation and characterization of polyvinylidene fluoride (PVDF) hollow fiber membranes

Polyvinylidene fluoride (PVDF) hollow fiber membranes were prepared by dry/wet and wet phase inversion methods. In spinning these PVDF hollow fibers, dimethylacetamide (DMAc) and polyvinyl pyrrolidone (PVP) were used as a solvent and an additive, respectively. Water was used as the external coagulant. Water or ethanol was used as the internal coagulants. The membranes were characterized in terms of water flux, molecular weight cut-off for the wet membranes. Gas permeation fluxes and effective surface porosity were determined by a gas permeation method for the dried membranes. The cross-sectional structures were examined by scanning electron microscopy. The effects of polymer concentration, air-gap, PVP molecular weight, PVP content in the polymer dope, and the internal coagulant on the permeation properties and membrane structures were examined. Highly permeable PVDF hollow fiber membranes could be prepared from a polymer dope containing low molecular weight PVP and using ethanol as the internal coagulant.     

基板界面对PS/PMMA共混物薄膜相逆转组成比的影响

近年来高分子共混体系中的界面、表面效应逐渐引起了越来越多研究者的兴趣 .人们发现 ,当共混物薄膜厚度减至一定程度时 ,聚合物共混物薄膜中的相形态、相容性及相分离动力学与本体中有较大的不同[1～ 3] .基板界面作用对共混薄膜体系的热力学、动力学行为产生很大的影响 .我们以往的研究 [4 ,5]也发现 ,PP/EVAc(70 /30 )共混体系退火过程中 ,基板界面 (如玻璃 )作用可大大加速分散相(EVAc)粒子的粗化凝聚过程 .本研究用聚甲基丙烯酸甲酯和聚苯乙烯共混物的四氢呋喃溶液在不同基板介质 (如玻璃基板 ,PP基板 )上成膜 ,用相差显微镜观测了…