Electrospinning of polystyrene/poly(2‐methoxy‐5‐(2′‐ethylhexyloxy)‐1,4‐phenylene vinylene) blends

Ultrafine polystyrene (PS)/poly(2‐methoxy‐5‐(2′‐ethylhexyloxy)‐1,4‐phenylene vinylene) (MEH‐PPV) fibers were successfully prepared by electrospinning of PS/MEH‐PPV solutions in chloroform, 1,2‐dichloroethane, and tetrahydrofuran (THF). Three concentrations of the solutions were prepared: 8.5, 16, and 23.5% (w/v), with the compositional weight ratios between PS and MEH‐PPV being 7.5:1, 15:1, and 22.5:1, respectively. Smooth fibers only observed from 23.5% (w/v) PS/MEH‐PPV solution in chloroform. Improvement in the electrospinnability of 8.5% (w/v) PS/MEH‐PPV solution in chloroform was achieved by addition of an organic salt, pyridinium formate (PF), or by addition of a minor solvent with a high dielectric constant value. The average diameters of the as‐spun PS/MEH‐PPV fibers were between 0.30 and 5.11 μm. Last, photoluminescence of 8.5% (w/v) solutions of PS/MEH‐PPV in a mixed solvent system of chloroform and 1,2‐dichloroethane of various volumetric compositions and the resulting as‐spun fibers was investigated and compared. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 1881–1891, 2005     

Conformation and luminescence characteristics of nanopoly[2‐metoxy‐5‐(2′‐ethyl‐hexyloxy)‐p‐phenylene vinylene] in two‐dimensional arrays

With anodic alumina with an ordered nanopore array used as a template, poly[2‐metoxy‐5‐(2′‐ethyl‐hexyloxy)‐p‐phenylene vinylene] (MEH–PPV) was embedded into the nanopores, and then two‐dimensional arrays of light‐emitting nanopolymers were prepared. By the measurement and analysis of photoluminescence and photoluminescence excitation spectra of the samples, it was demonstrated that the optical properties of the nano‐MEH–PPV arrays were obviously different from those of MEH–PPV films. The conformations of the MEH–PPV chains in the nanopores, films, and solutions and their effects on the optical properties were examined. It was determined experimentally that the conformations of the MEH–PPV chains in the solutions were maintained in the nano‐MEH–PPV arrays. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 3037–3041, 2006     

Thermally stable red electroluminescent hybrid polymers derived from functionalized silsesquioxane and 4,7‐bis(3‐ethylhexyl‐2‐thienyl)‐2,1,3‐benzothiadiazole

Hyperbranched organic–inorganic hybrid conjugated polymers P1 and P2 were prepared via FeCl₃‐oxiditive polymerization of 4,7‐bis(3‐ethylhexyl‐2‐thienyl)‐2,1,3‐benzothiadiazole ( A ) and octa(3‐ethylhexyl‐2‐thienyl‐phenyl)polyhedral oligomeric silsesquioxane (POSS) ( B ) at different POSS concentrations. Compared to linear polymer PM derived from A , P1 , and P2 exhibit much higher PL quantum efficiency (?_PL‐f) in condensed state with improved thermal stability. ?_PL‐f of P1 and P2 increased by 80% and 400%, and the thermal degradation temperatures of P1 and P2 are increased by 35 °C and 46 °C, respectively. Light‐emitting diodes were fabricated using P1 , P2 , and PM . While the electroluminescent spectra of both P1 and PM show λ_max at 660 nm, P1 exhibits a much narrower EL spectrum and higher electroluminescence (～500%) compared with PM at a same voltage and film thickness. The maximum current efficiency of P1 is more than seven times of that of PM . The turn‐on voltages of the LEDs are in the order of P2 > PM > P1 . LED prepared by blending P1 with MEH‐PPV shows a maximum luminescence of 2.6 × 10³ cd/m² and a current efficiency of 1.40 cd/A, which are more than twice (1.1 × 10³ cd/m²) and five times (0.27 cd/A) of LED of PM /MEH‐PPV blend, respectively. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 5661–5670, 2009     

Enhancement of color purity in blue light emitting poly(fluorene)s and poly(p‐phenylene)s with 2,6‐distyrylpyridine kinked segments along the backbone

2,6‐bis(4‐Distyrylpyridine) ( 1 ) was synthesized by the condensation of 2,6‐dimethylpyridine with 4‐bromobenzaldehyde. Two new series of soluble random or alternating polyfluorenes ( PF‐Py ) and poly‐p‐phenylenes ( PP‐Py ) with various compositions were prepared by Suzuki coupling utilizing 1 as a comonomer. These polymers showed optical band gaps of 3.00–3.07 eV and photoluminescence (PL) quantum yields in solution of 0.37–0.91 for PF‐Py and 0.29–0.38 for PP‐Py . Polymers PF‐Py emitted blue light with PL maximum at 410–424 nm in solution and 406–428 nm in thin films that was red shifted with increasing distyrylpyridine content. Polymers PP‐Py behaved as blue emitters both in solution and in solid state, with PL maximum at 416–436 nm. The optical properties of these polymers could be tuned by the reversible protonation–deprotonation process of the pyridine ring. The emitted color of the polymers in solution and thin film could be changed continuously between blue and green (PL maximum up to about 520 nm) by exposing the polymers to the acid or base environment. Thin films of PF‐Py displayed excellent color stability with a small red shift of 10 nm but without additional emission band in the long wave region of the spectrum, even after being annealed at high temperature for a long time. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 4486–4495, 2005     

Preparation of MEH‐PPV/nanosized titania hybrids via in situ sol–gel reaction of titanium alkoxide: Optical property

Homogenously dispersed organic (MEH‐PPV)/inorganic (nanosized titania) hybrids were successfully synthesized. The method of preparation was based on a simple one‐step in situ sol–gel technique using titanium isopropoxide (TIP) as the precursor. The key benefit of this preparation was that TIP interacted with both 2‐chlorophenol and MEH‐PPV, so that the degree of aggregation and phase separation could be kept to a minimum with a suitable recipe. MEH‐PPV/TIP/H₂O/2‐chlorophenol of various weight ratios were synthesized to examine the morphology as well as optical properties of the MEH‐PPV/TIP(titania) hybrid. The observation of MEH‐PPV gelation and Fourier transform infrared results verified the interaction existing between MEH‐PPV and TIP. SEM photographs showed that TIP(titania) were homogenously dispersed in the MEH‐PPV film if the hybrid solution was clear from the use of a suitable recipe. UV–vis absorption measurements showed that the addition of TIP decreased the conjugation length of MEH‐PPV. A redshift in the photoluminescence (PL) emission was observed in almost all the hybrids in the solution state, because of the aggregation of MEH‐PPV. However, it was found that spinning destroyed the aggregation of MEH‐PPV, resulting in a blueshift in the PL emission of the hybrids. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 515–529, 2008     

High‐quality poly[2‐methoxy‐5‐(2′‐ethylhexyloxy)‐p‐phenylenevinylene] synthesized by a solid–liquid two‐phase reaction: Characterizations and electroluminescence properties

Poly[2‐methoxy‐5‐(2′‐ethylhexyloxy)‐p‐phenylenevinylene] (MEH‐PPV) with a molar mass of 26–47 × 10⁴ g mol^?1 and a polydispersity of 2.5–3.2 was synthesized by a liquid–solid two‐phase reaction. The liquid phase was tetrahydrofuran (THF) containing 1,4‐bis(chloromethyl)‐2‐methoxy‐5‐(2′‐ethylhexyloxy)benzene as the monomer and a certain amount of tetrabutylammonium bromide as a phase‐transfer catalyst. The solid phase consisted of potassium hydroxide particles with diameters smaller than 0.5 mm. The reaction was carried out at a low temperature of 0 °C and under nitrogen protection. No gelation was observed during the polymerization process, and the polymer was soluble in the usual organic solvents, such as chloroform, toluene, THF, and xylene. A polymer light‐emitting diode was fabricated with MEH‐PPV as an active luminescent layer. The device had an indium tin oxide/poly(3,4‐ethylenedioxylthiophene) (PEDOT)/MEH‐PPV/Ba/Al configuration. It showed a turn‐on voltage of 3.3 V, a luminescence intensity at 6.1 V of 550 cd/m², a luminescence efficiency of 0.43 cd/A, and a quantum efficiency of 0.57%. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 3049–3054, 2004     

Enhancing quantum efficiency of MEH‐PPV through the reduction of chain aggregations by thermal treatments

The quantum efficiencies of photoluminescence (PL) and electro‐luminescence (EL) of poly[2‐methoxy‐5‐(2′‐ethyl‐hexyloxy)‐1,4‐phenylenevinylene] (MEH‐PPV) were significantly increased by heat treatments under vacuum with further removing the undissolved portion. The UV–vis absorption was found to decrease with heating time, while PL intensity increased. The maximum PL quantum yield was 6.5 times that of the untreated MEH‐PPV, which was attributed to the reduction of chain aggregations and the interruption of conjugation length. The maximum EL quantum yield of their prepared ITO/PANI/MEH‐PPV/Ca/AL light emitting diodes (PLED) was 46 (at 3 V) times that of the untreated sample. A typical turn‐on voltage of 2.5 V for MEH‐PPV PLED was able to decrease to 1 V after heat treatments, which was believed to result from the decrease of cis linkages in the polymer chains as revealed by the ¹H NMR spectroscopy. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 1705–1711, 2005     

Effects of chain conformation and chain length on degree of aggregation in assembled particles of conjugated polymer in solvents–nonsolvent: A spectroscopic study

This article explores photophysical properties and aggregation behaviors of conjugated polymer, poly[2‐methoxy, 5‐(2′‐ethylhexyloxy)‐1,4‐phenylenevinylene](MEH?PPV), in various solvent–nonsolvent systems by utilizing UV/vis absorption and photoluminescence (PL) spectroscopy. The isolated chains of MEH‐PPV dispersed in solvents including dichloromethane, chloroform, and tetrahydrofuran adopt either extended or collapsed conformations depending on local polymer–solvent interactions. Aggregation of the MEH‐PPV in these solvents is induced by addition of a poor solvent, cyclohexane. The formation of aggregates is indicated by the appearance of distinct red‐shift peaks in the absorption and PL spectra. The degree of aggregation in each solvent–nonsolvent system is compared by means of absorbance and PL intensity of the aggregate bands. In early stage of the aggregation, the amount of aggregates in system is controlled by the solubility of polymer. When the polymer chains are forced to densely pack within assembled particles by increasing ratio of cyclohexane to 99 v/v %, the conformation of individual chain plays important role. We have found that the extended chains facilitate the aggregation in the assembled particles. Increasing chain length of polymer promotes the aggregation in early stage and densely packed particles. Size distribution of the assembled particles is also found to depend on the choice of solvent. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 894–904, 2010     

Enhancing the electroluminescent efficiency of poly{5‐methoxy‐2‐[(2′‐ethyl‐hexyl)‐oxy]‐p‐phenylenevinylene}/poly(2,3‐diphenyl‐5‐octyl‐p‐phenylenevinylene) polyblends by the introduction of chemical bonding through a thermal treatment

A significant improvement in the electroluminescence (EL) properties was observed for a poly{5‐methoxy‐2‐[(2′‐ethyl‐hexyl)‐oxy]‐p‐phenylenevinylene} (MEH–PPV)/poly(2,3‐diphenyl‐5‐octyl‐p‐phenylenevinylene) (DPO–PPV) blend after a thermal treatment at 200 °C for 2 h in vacuo to furnish the chemical bonding between polymer chains. ¹H NMR spectroscopy and two‐photon excitation microscopy revealed that the chemical bonding turned the immiscible polyblend into a system more like a block copolymer with a vertically segregated morphology. Because both the lowest unoccupied molecular orbital and highest occupied molecular orbital levels of MEH–PPV in the wetting layer were higher than those of DPO–PPV in the upper layer, the heterojunction between the two layers of the polymers fit the category of so‐called type II heterojunctions. As a result, the turn‐on voltage of the polymer light‐emitting diode prepared with the thermally treated polyblend decreased to ～0.6 V, and the EL emission intensities and quantum efficiencies increased to about 4 times those of the untreated polyblend. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 62–69, 2006     

Segmented poly[2‐methoxy‐5‐(2‐ethylhexyloxy)‐1,4‐phenylene vinylene] via xanthate and dithiocarbamate precursors: A comparative study of thermal eliminations

Segmented poly[2‐methoxy‐5‐(2‐ethylhexloxy)‐1,4‐phenylene vinylene] (MEH‐PPV)‐x's, which contain conjugated segments of varying lengths that are interspersed by nonconjugated units along the polymer backbone, were synthesized by selective thermal elimination of precursors containing controlled amounts (x) of a thermally labile group, namely, xanthate or dithiocarbamate (DTC). These precursors were in turn synthesized by competitive nucleophilic substitution of the Wessling polyelectrolyte with varying molar fractions of the respective nucleophiles—potassium ethyl xanthate or sodium diethyl dithiocarbamate. Methanol, used as the reaction medium, also served to introduce the second thermally less labile nucleophilic substituent. This approach for the preparation of segmented MEH‐PPV‐x is superior to the previous approach that used acetate as the thermally labile group, because it offers greater control over the composition despite a simpler synthetic procedure. Detailed studies of the thermal‐elimination kinetics of the three precursors, namely, acetate, xanthate, and DTC, both in solution and in thin films, were carried by in situ monitoring of their ultraviolet–visible spectra. These studies revealed that the rates of elimination followed the order, DTC > xanthate > acetate. The activation energies for the elimination were, however, not widely different (ca. 30 kcal/mol), suggesting that the rates primarily reflected differences in the pre‐exponential factor. After elimination, the segmented MEH‐PPV‐x samples exhibited the expected redshift in their absorption and fluorescence spectra with an increasing molar fraction (x) of eliminated segments, which was accompanied by a drastic reduction in the fluorescence quantum yields. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 3929–3940, 2003     

Chain composition dependence of luminescence properties for copolymers of 2‐methoxy‐5‐2′‐ethyl‐hexyloxy‐1,4‐phenylenevinylene and 2,3‐diphenyl‐5‐octyl‐1,4‐phenylenevinylene

The copolymers of 2‐methoxy‐5‐2′‐ethyl‐hexyloxy‐1,4‐phenylenevinylene (MEH‐PV) and 2,3‐diphenyl‐5‐octyl‐1,4‐phenylenevinylene were prepared via the Gilch route with their chain compositions and the reactivity ratios of the monomers estimated by ¹H NMR spectroscopy. The results indicated that the copolymers tended to form an alternative copolymer as the feed ratio of the monomers closed to one‐half. When an individual copolymer solution in tetrahydrofuran was spun‐cast to form a film, the MEH‐PV units were able to attract the like units from the adjacent chains. As a result, the ultraviolet–visible absorption spectrum of the alternative copolymer in film form was broader than the spectra of those with different compositions. The photoluminescence spectra of the copolymers in film form exhibited the characteristic shoulder of poly(2‐methoxy‐5‐2′‐ethyl‐hexyloxy‐1,4‐phenylenevinylene), even though the content of MEH‐PV units was not great enough for the formation of repeat units in sequence. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 2180–2186, 2003     

A π‐stacked and conjugated hybrid based on poly(N‐vinylcarbazole) postfunctionalized with terfluorene for stable deep‐blue hole‐transporting materials

The combination of π‐stacked with π‐conjugated building blocks offers an essential strategy to construct multifunctional organic semiconductors (MOSs) with the unique optoelectrical properties. Covalent hybrids can efficiently avoid the intrinsic phase‐separation defects in corresponding blend system. In this contribution, poly(vinylcarbazole) tethered with terfluorene, PVK‐TF, as a double‐channeled π‐stacked and π‐conjugated hybrid (SCH), has been constructed via Friedal‐Crafts click postmodification (FCCP). The chemical structure and optoelectrical property were determined by GPC, UV–vis, PL, TGA, DSC, and CV. Its PL spectra in the annealing thin film at N₂ atmosphere without low‐energy emission bands centered at the 530 nm indicates that no π‐stacks between carbazole and TF or among TFs dominate the whole condensed phase, which is in agreement with the intrachain T‐shaped π‐pitched motifs in molecular modeling simulation due to steric hindrance effect in complicated diarylfluorenes (CDAFs). A supporting prototype stable deep‐blue PLED was successfully obtained with an Internationale de l'Eclairage (CIE) coordinates of (0.20, 0.10) and a width at half maximum (FWHM) of about 60 nm at high current density of 100 mA/cm² (35 V). Deep‐blue PVK‐TF is a promising MOS for hole‐transporting and host materials. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 5221–5229, 2009     

Synthesis and optical properties of a poly(p‐phenylenevinylene) derivative and polyfluorenes with bipolar groups along the main chain

A poly(p‐phenylenevinylene) derivative (PPV–TPA)] and a series of statistical copolyfluorenes (PF–TPA)] containing oxadiazole and triphenylamine segments along the main chain were synthesized by the Heck reaction and nickel‐mediated coupling, respectively. The PF–TPA copolyfluorenes with relatively low contents of oxadiazole and triphenylamine units were readily soluble in common organic solvents, whereas the other copolyfluorenes displayed lower solubility. PPV–TPA showed excellent solubility in solvents such as tetrahydrofuran (THF), dichloromethane, chloroform, and toluene. Thin films of the polymers absorbed light in the range of 375–396 nm and had optical band gaps of 2.76–2.98 eV. They emitted blue‐green light with a maximum at 414–522 nm. The fluorescence quantum yields in THF solutions were 0.08–0.53. The copolyfluorene PF–TPA thin films with high contents of oxadiazole and triphenylamine moieties emitted pure blue light that remained stable even after annealing at 150 °C for 4 h in air. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 3556–3566, 2006     

Fluorescence Quenching of Poly[2-methoxy-5-（2′-ethylhexoxy）-p-phenylene vinylene] （MEH-PPV） in Solutions

Fluorescence quenching processes of poly[2-methoxy-5-(2‘ethyl-hexoxy)-p-phenylene vinylene] (MEH-PPV) in solution by electron acceptors, O2 and acid, have been studied. Static quenching of the fluorescence from MEH-PPV by an electron acceptor (DDQ or TCNE) occurs due to electron transfer from MEH-PPV to the electron acceptor and this electron transfer quenching can be promoted by chloroform. Photooxidation takes place in the MEH-PPV solution and singlet oxygen is an intermediate in the photooxidation, according to the results of ESR spectroscopy. Acid also plays an important role in the fluorescence quenching process of MEH-PPV, by the protonation of the alkoxy groups in the molecular chain.     

Full color light‐emitting electrospun nanofibers prepared from PFO/MEH‐PPV/PMMA ternary blends

In this study, luminescence electrospun (ES) nanofibers based on ternary blends of poly(9,9‐dioctylfluoreny‐2,7‐diyl) (PFO)/poly[2‐methoxy‐5‐(2‐ethylhexyloxy)‐1,4‐phenylenevinylene] (MEH‐PPV)/poly(methyl methacrylate) (PMMA) were prepared from chloroform solutions using a single capillary spinneret. Effects of PFO/MEH‐PPV ratio on the morphology and photophysical properties were studied while the PMMA weight percentage was fixed at 90 wt %. The morphologies of the prepared ES fibers were characterized by FE‐SEM and fluorescence microscopy. The obtained fibers had diameters around a few hundred nm and pore sizes in the range of 30–35 nm. The emission colors of the PFO/MEH‐PPV/PMMA blend ES fibers changed from blue, white, yellowish‐green, greenish‐yellow, orange, to yellow, as the MEH‐PPV composition increased. In contrast, the emission colors of the corresponding spin‐coated films were blue, orange, pink‐red, red, and deep‐red. Based on the values of solubility parameters, the PFO and MEH‐PPV are miscible to each other and trapped in the PMMA matrix. Hence, energy transfer between these two polymers is possible. The smaller aggregated domains in the ES fiber compared to those of spin‐coated films possibly reduce the efficiency of energy transfer, leading to different emission colors. Also, the prepared ES fibers had higher photoluminescence efficiencies than those of the spin‐coated films. Pure white light‐emitting fibers prepared from the PFO/MEH‐PPV/PMMA blend ratio of 9.5/0.5/90 had the Commission Internationale de L'Eclairage (CIE) coordinate of (0.33, 0.31). Our results showed that different color light‐emitting ES fibers were produced through optimizing the composition of semiconducting polymer in the transparent polymer matrix. This type of ES fibers could have potential applications as new light sources or sensory materials for smart textiles. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 463–470, 2009     

Fluorescent PMMA/MEH‐PPV electrospun nanofibers: Investigation of morphology,solvent, and surfactant effect

Electrospinning is a powerful technique to produce nanofibers of tunable diameter and morphology for medicine and biotechnological applications. By doping electrospun nanofibers with inorganic and organic compounds, new functionalities can be provided for technological applications. Herein, we report a study on the morphology and optical properties of electrospun nanofibers based on the conjugated polymer poly[2‐methoxy‐5‐(2‐ethylhexyloxy)‐1,4‐phenylenevinylene] (MEH‐PPV) and poly(methylmethacrylate) (PMMA). Initially, we investigate the influence of the solvent, surfactant, and the polymer concentration on electrospinning of PMMA. After determining the best conditions, 0.1% MEH‐PPV was added to obtain fluorescent nanofibers. The optical characterizations display the successful impregnation of MEH‐PPV into the PMMA fibers without phase separation and the preservation of fluorescent property after fiber electrospinning. The obtained results show the ability of the electrospinning approach to obtain fluorescent PMMA/MEH‐PPV nanofibers with potential for optical devices applications. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2014 , 52, 1388–1394     

Copolyfluorenes containing pendant bipolar carbazole and 1,2,4‐triazole groups: Synthesis,characterization, and optoelectronic applications

Three novel copolyfluorenes ( P1 ‐ P3 ) containing pendant bipolar groups (2.5–7.7 mol %), directly linked hole‐transporting carbazole and electron‐transporting aromatic 1,2,4‐triazole, were synthesized by the Suzuki coupling reaction and applied to enhance emission efficiency of polymer light‐emitting diodes based on conventional MEH‐PPV. The bipolar groups not only suppress undesirable green emission of polyfluorene under thermal annealing, but also promote electron‐ and hole‐affinity of the resulting copolyfluorenes. Blending the bipolar copolyfluorenes with MEH‐PPV results in significant enhancement of device performance [ITO/PEDOT:PSS/MEH‐PPV+ P1 , P2 or P3 /Ca(50 nm)/Al(100 nm)]. The maximum luminance and luminance efficiency were enhanced from 3230 cd/m² and 0.29 cd/A of MEH‐PPV‐only device to 15,690 cd/m² and 0.81 cd/A (blend device with MEH‐PPV/ P3 = 94/6 containing about 0.46 wt % of pendant bipolar residues), respectively. Our results demonstrate the efficacy of the bipolar copolyfluorenes in enhancing emission efficiency of MEH‐PPV. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Synthesis and photovoltaic properties of poly(p‐phenylenevinylene) derivatives containing oxadiazole

A novel poly(p‐phenylenevinylene) PPV‐based copolymer (3C‐OXD‐PPV) with electron‐deficient oxadiazole segments as the side chain has been successfully synthesized through the Gilch polymerization. The obtained copolymer is soluble in common organic solvents such as chloroform, tetrahydronfuran, and 1,1,2,2‐tetrachloroethane. The copolymer was characterized by ¹H NMR, elemental analysis and GPC. TGA measurement of the copolymer shows it has good thermal stability with decomposition temperature higher than 350 °C. The absorption, electrochemical properties of the 3C‐OXD‐PPV were investigated and also compared with the properties of MEH‐PPV. The HOMO and LUMO levels of 3C‐OXD‐PPV were estimated from the electrochemical cyclic voltammograms. Bulk‐heterojunction PVCs were fabricated by using 3C‐OXD‐PPV blended PCBM as an active layer. The PCE of the PVC is 1.60% under 100 mW cm^?2 AM 1.5 illumination, which indicates that 3C‐OXD‐PPV is a potential candidate for the application of polymer PVC. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 1003–1012, 2009     

Synthesis and characterization of novel germanium‐containing poly(p‐phenylenevinylene) derivatives

Novel blue‐emitting germanium‐containing poly(p‐phenylenevinylene) (PPV) derivatives with well‐defined conjugation lengths were synthesized via Wittig‐condensation polymerizations. The polymers can be color‐tuned by the introduction of various chromophores into the PPV‐based polymer backbones. The photoluminescence (PL) spectra of the polymers, GePVK (containing carbazole moieties), GeMEH (containing dialkoxybenzene moieties), and GePTH (containing phenothiazine moieties), were found to exhibit blue, greenish blue, and green emissions, respectively. GePTH produces more red‐shifted emission than GeMEH and GEPVK, resulting in green emission, and the solution and solid state PL spectra of GePVK consist of almost blue emission. The electroluminescence spectra of GeMEH and GePTH contain yellowy green and yellow colors, respectively. Interestingly, GePVK exhibits white emission with CIE coordinates of (0.33, 0.37) due to electroplex emission in the light‐emitting diodes. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 979–988, 2008     

Deep‐blue light‐emitting polyfluorenes containing spiro[fluorene‐9,9′‐thioxanthene‐S,S‐dioxide] isomers

Blue light‐emitting polyfluorenes, PPF‐FSOs and PPF‐SOFs were synthesized via introducing spiro[fluorene‐9,9′‐thioxanthene‐S,S‐dioxide] isomers (2,7‐diyl and 2′,7′‐diyl) (FSO/SOF) into the poly[9,9‐bis(4‐(2‐ethylhexyloxy) phenyl)fluorene‐2,7‐diyl] (PPF) backbone, respectively. With the increasing contents of FSO and SOF moieties, the absorption and PL spectra of PPF‐FSOs show slight red shift, while that of PPF‐SOFs exhibit blue shift, respectively. The HOMO and LUMO levels reduce gradually with increasing SOF unit in PPF‐SOFs. The polymers emit blue light peaked around 430–445 nm and show an excellent spectral stability with the variation in current densities. The distinctly narrowing EL spectra were observed with the incorporation of isomers in the polymers. The full width at half maximum reduced by 15 nm for PPF‐SOFs, resulting in a blue shift with the CIE coordinates from (0.16, 0.11) to (0.16, 0.08). With a device configuration of ITO/PEDOT:PSS/EML/CsF/Al, a maximum luminance efficiency (LE_max) of 2.00 cd A^?1, a maximum external quantum efficiency (EQE_max) of 3.76% with the CIE coordinates of (0.16, 0.08) for PPF‐SOF15 and a LE_max of 1.68 cd A^?1, a EQE_max of 2.38% with CIE (0.16, 0.12) for PPF‐FSO10 were obtained, respectively. The result reveals that spiro[fluorene‐9,9′‐thioxanthene‐S,S‐dioxide] isomers are promising blocks for deep‐blue light‐emitting polymers. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55 , 2332–2341