Fabrication of well‐aligned electrospun nanofibrous membrane based on fluorinated polyimide

We have fabricated novel nanofibrous fluorinated polyimide membranes on a specially designed collector, which is composed of conductive aluminum plates and glass insulator materials and can be removed from the apparatus, using an electrospinning method. We describe the structure and water flux properties of the nanofibrous fluorinated polyimide membranes. The electrospun nanofibers were deposited across the plates and uniaxially aligned to the collector. In addition, the multi‐layer stacked nanofibrous membranes, consisting of three‐dimensionally ordered nanopores, were produced. The pure water fluxes for the stacked membranes were measured, using a stirred dead‐end filtration cell, and were linearly decreased with an increasing deposition time, indicating that the nanopores formed in the nanofibrous membrane were further narrowed due to the regularly accumulated nanofibers. Copyright © 2009 John Wiley & Sons, Ltd.     

Effect of type of solvent and non‐solvents on morphology and performance of polysulfone and polyethersulfone ultrafiltration membranes for milk concentration

Polysulfone (PS) and polyethersulfone (PES) ultrafiltration membranes were manufactured from a casting solution of the polymer, polyvinylpyrrolidone (PVP) in various solvents [N,N‐dimethylacetamide (DMAc), N,N‐dimethylformamide (DMF) and 1‐methyl‐2‐pyrrolidone (NMP)] by immersing the prepared films in different non‐solvents [water, 2‐butanol, mixture of water and 2‐butanol, mixture of water and 2‐propanol (IPA) and mixture of water and 1‐butanol]. The influences of various solvents and non‐solvents on morphology and performance of the prepared membranes were analyzed by scanning electron microscopy (SEM) and separation experiments using milk as the feed. Copyright © 2005 John Wiley & Sons, Ltd.     

Preparation and characterization of asymmetric polyethersulfone (PES) membranes

Flat‐sheet asymmetric polyethersulfone (PES) membranes were prepared from polyethersulfone (PES)/ polyethylene glycol (PEG)/ N‐methyl‐2‐pyrrolidone (NMP) system via phase inversion induced by immersion precipitation in water coagulation bath. Effects of propionic acid (PA) as a non‐solvent additive (NSA) on morphology and performance of the membranes prepared from PES/PEG 6000/NMP system in water coagulation bath were investigated. The cross section morphology of the membranes was studied by scanning electron microscopy (SEM). In addition, performance of the membranes was studied by water content measurements and separation experiments using pure water and human serum albumin (HSA) protein solution as feeds. According to SEM analysis, it was found out that the NSA has a significant influence on the structure of the skin layer and the sublayer. The obtained results indicated that addition of PA to the casting solution decreases permeation flux of the prepared membranes. Copyright © 2009 John Wiley & Sons, Ltd.     

The formation of ultrafine polyamide 6 nanofiber membranes with needleless electrospinning for air filtration

Particulate matter (PM) is a major air pollutant, which has a significant impact on public health. Filtration of PM through filters is a common method to protect the environment. However, the effective removal of PM with conventional filters still remains a challenge because of its small sizes. Here, we reported the formation of ultrafine polyamide 6 (PA‐6) nanofiber membranes formed with needleless electrospinning, in which both relative humidity condition and electrode type were included in the discussion. The PA‐6S nanofibers formed by using spiral electrode as a spinneret at 60% RH had the diameter of 33 nm, while the PA‐6C nanofibers formed by using cylindrical electrode had the diameter of 120 nm. With the integration of fine diameter, small pore size, and high porosity, the resultant PA‐6S nanofiber membrane exhibits high filtration efficiency of 99.42% and low pressure drop of 85.5 Pa under a face velocity of 85 L/min. Besides, it took only 10 minutes to reduce the concentration of PM_2.5 from 999 to 34.1 μg/m³ when used to filter real PM particles.     

静电纺荧光纳米纤维膜在痕量爆炸物检测中的应用

爆炸物检测作为打击爆炸恐怖主义的重要措施之一,正日益彰显出广阔的应用前景.其中,静电纺荧光纳米纤维膜在爆炸物检测领域已展现出其独特的优点,可满足爆炸物检测所需的检测速度快、检测灵敏度高等要求.本文总结了近年来静电纺荧光纳米纤维膜在爆炸物检测中的代表性成果,简要介绍了爆炸物荧光传感机理、静电纺丝技术原理、静电纺荧光纳米纤维膜的制备方法及其爆炸物检测性能的影响因素;系统、重点梳理了有机小分子体系、共轭聚合物体系、聚集诱导发光体系及其他荧光材料体系的静电纺荧光纳米纤维膜在爆炸物检测中的应用,并针对该领域尚未解决的问题和未来可能的发展方向进行了展望,可为实际爆炸物检测中静电纺荧光纳米纤维膜的设计提供指导.     

Enhanced antifouling and anticoagulant properties of grafted biomolecule polyethersulfone membranes

Polyethersulfone (PES) has been widely used in membrane technology and used to purify water in water treatments application or as a dialyzer to purify blood in hemodialysis. In this work, PES was chemically modified by separately grafting two biomolecules, 4‐aminobenzenesulfonamide (ABS), and 4‐amino‐N‐(5‐methylisoxazol‐3‐yl)benzenesulfonamide (AMBS), on PES backbone, and these modified membranes were blended to unmodified PES, in 1:1 ratio, in order to obtain PES‐b‐PES‐ABS and PES‐b‐PES‐AMBS membranes. The first aim of this study is to measure the anticoagulant properties of the modified membrane by measuring the activated partial thromboplastin time (APTT) and prothrombin time (PT). The second aim of the study is to evaluate the antifouling properties of the modified PES membranes by examining its antimicrobial activity against two Gram‐negative bacteria, which are Pseudomonas aeruginosa (P. aeruginosa) and Escherichia coli (E. coli); two Gram‐positive bacteria, which are Bacillus subtilis (B. subtilis) and Staphylococcus aureus (S. aureus); and a fungus, which is Candida albicans (C. albicans). The results showed that grafting of ABS and AMBS improved overall the hydrophilicity properties of the modified PES membranes. PES‐b‐PES‐ABS membranes showed better anticoagulant properties with 13 seconds for PT and 38 seconds for APPT, in comparison with the control sample (pure plasma), which showed 12 seconds for PT and 30 seconds for APPT. For antimicrobial tests, both PES‐b‐PES‐ABS and PES‐b‐PES‐AMBS membranes did not show any antibacterial activity, but when zinc oxide (ZnO) nanoparticles were added to the modified PES membranes in concentrations between 3% to 5% w/w, PES‐b‐PES‐ABS‐ZnO (M‐4 and M‐5), and PES‐b‐PES‐AMBS‐ZnO (M‐8 and M‐9) nanocomposite membranes showed antibacterial activity against P. aeruginosa and S. aureus.     

Recent progress in electrospun nanofibers: Reinforcement effect and mechanical performance

Composite materials are becoming increasingly important as structural materials for aeronautical and space engineering, naval, automotive, and civil engineering, sporting goods, and other consumer products. Fiber‐based reinforcement represents one of the most effective manufacturing strategies for enhancing the mechanical strength and other properties of composite materials. Electrospinning has gained widespread interest in the last two decades because of its ability to fabricate continuous ultrafine nanofibers with unique characteristics. The impact of electrospinning on fiber synthesis and processing, characterization, and applications in drug delivery, nanofiltration, tissue scaffolding, and electronics has been extensively studied in the past. In this article, the authors have focused on a comprehensive review of the mechanical performance and properties of electrospun nanofibers as potential reinforcements as well as their advanced nanocomposites. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 1171–1212     

Cellulose acetate and polyethersulfone blend ultrafiltration membranes. Part I: Preparation and characterizations

The overall objective of this investigation is to achieve high‐performance membranes with respect to flux and rejection characteristics, with an interplay of blending polymers having desired qualities. Thus, cellulose diacetate and polyethersulfone as candidate materials, in the presence of polyethylene glycol 600 as a pore forming agent, were blended in 100/0, 95/5, 90/10, 85/15, 80,20 and 75/25% compositions using N,N′‐dimethylformamide as solvent and membranes were prepared by the phase inversion technique. Polymer blend composition, additive concentration, and casting and gelation conditions were standardized for the preparation of asymmetric membranes with various pore statistics and morphology. These blend membranes were characterized for compaction in ultrafiltration experiments at 414 kPa pressure in order to attain steady state flux and is reached within 4–5 hr. The pure water flux was measured at 345 kPa pressure and is determined largely by the composition of polyethersulfone and additive concentration. The flux was found to reach the highest values of 66.5 and 275 1/(cm² hr) at 0 and 10 wt% additive concentrations respectively, at 25% SPS content of the blend. Membrane hydraulic resistance derived by measuring water flux at various transmembrane pressure and by using an algorithm was found to be inversely proportional to pure water flux. Water content is estimated by simple drying and weighing procedures and found proportional to pure water flux for all the membranes. The molecular weight cut‐offs (MWCOs) of different membranes were determined with proteins of different molecular weights and found to vary from 20–69 kDa (globular proteins) depending on the PEG and SPS content in the casting dope. Skin surface porosity of the membranes were analyzed by scanning the frozen membrane samples using scanning electron microscopy (SEM) at different magnifications. The surface porosity is in direct correlation to the MWCO derived from solute retention experiments. Copyright © 2004 John Wiley & Sons, Ltd.     

Preparation and characterization of PHB/PBAT–based biodegradable antibacterial hydrophobic nanofibrous membranes

In this study, polyhydroxybutyrate/poly(butyleneadipate‐co‐terephthalate) (PHB/PBAT) nanofibrous membranes were produced by electrospinning the blends of biodegradable PHB and PBAT. The antibacterial hydrophobic nanofiber membranes were obtained by grafting 1‐allylhydantoin and perfluorooctyl acrylate onto the PHB/PBAT membranes. The prepared nanofibrous membranes were chlorinated with chlorine bleach and characterized by scanning electron microscopy, Fourier transform infrared, and thermogravimetric analysis. The chlorinated nanofibrous membranes exhibited efficient antimicrobial activity against Escherichia coli O157:H7 (ATCC 43895) and Staphylococcus aureus (ATCC 6538) with 6.08 and 5.78 log reduction, respectively. The contact angle of this antibacterial membrane was 123.1° ± 1.9°. The treated membranes showed good stability and durability towards UV‐A light exposure and storage. Therefore, our designed antibacterial hydrophobic nanofibrous membranes may have great potential for use in food packaging.     

Phosphorylated polyacrylonitrile‐based electrospun nanofibers for removal of heavy metal ions from aqueous solution

The phosphorylated polyacrylonitrile‐based (P‐PAN) nanofibers were prepared by electrospinning technique and used for removal of Cu²⁺, Ni²⁺, Cd²⁺, and Ag⁺ from aqueous solution. The morphological and structural properties of P‐PAN nanofibers were characterized by scanning electron microscope and Fourie transform infrared spectra. The P‐PAN nanofibers were evaluated for the adsorption capacity at various pH, contact time, and reaction temperature in a batch system. The reusability of P‐PAN nanofibers for the removal of heavy metal ions was also determined. Adsorption isotherms and adsorption kinetics were also used to examine the fundamental adsorption properties. It is found that the P‐PAN nanofibers show high efficiency, and the maximal adsorption capacities of metal ions as calculated from the Langmuir model were 92.1, 68.3, 14.8, and 51.7 mg/g, respectively. The kinetics of the heavy metal ions adsorption were found to follow pseudo‐second‐order rate equation, suggesting chemical adsorption can be regarded as the major factor in the adsorption process. Sorption/desorption results reveal that the obtained P‐PAN nanofibers can remain high removal efficiency after four cycles.     

Fabrication of electrospun polyethersulfone/titanium dioxide (PES/TiO2) composite nanofibers membrane and its application for photocatalytic degradation of phenol in aqueous solution

The main objective of this research is to use the photocatalytic properties of PES/TiO₂ nanofibers membranes to remove the phenol as a toxic pollutant in various effluents. The uniform fibers in terms of minimum bead formation and fibers diameter were fabricated. Therefore, more TiO₂ catalysts are on the surface of the fibers which increase the active surface area of nanoparticles and consequently improve the phenol degradation efficiency. The effects of TiO₂ concentration on hydrophilicity, mechanical properties, porosity, mean pore size, and water flux of membranes were studied. The PES/TiO₂ nanofibers were evaluated for phenol degradation under UVA irradiation through a transparent membrane module. The amount of removable phenol was analyzed with high‐performance liquid chromatography. Central composite design was used as a statistical experimental design. Finally, the effect of TiO₂ content in nanofibers and initial phenol concentrations were investigated as well as pH values in synthetic wastewater, on phenol degradation. The results from analysis of variance (ANOVA) analysis indicated that TiO₂ content in nanofibers was the most important and effective parameter on phenol degradation. It was also presented that there is no significant interaction between parameters so that the effect of each parameter was investigated separately. Maximum phenol degradation was 43.0 ± 0.3% and found under conditions of TiO₂ content, initial phenol concentration, and pH value of 8%, 120 ppm, and 7, respectively.     

Different types of electrospun nanofibers and their effect on microfluidic‐based immunoassay

Protein capturing on polymeric substrate of microfluidic devices is a key factor for the fabrication of immunoassay with high sensitivity. In this work, simple and versatile technique of electrospinning was used to produce electrospun nanofibrous membranes (e.NFMs) with high surface area as a substrate for microfluidic‐based immunoassay to increase sensitivity. It was found that the simultaneous use of e.NFM and 1‐Ethylethyl‐3‐(3‐dimethylaminopropyl)‐carbodiimide/N‐Hydroxysuccinimide hydroxysuccinimide as coupling agent has synergic effect on antigen immobilization onto the microchannels. It was found that the oxygen plasma technique for the creation of oxygen containing functional group like carboxyl and hydroxyl causes extreme leakage of solution through the microchannels. Thus, due to capillary effect, it is impossible to use hydrophilic substrate to modify microchannels. In order to compensate this problem, it is propose to utilize other type of polymer for the fabrication of nanofiber to answer this important question that if it is possible to enhance the sensitivity of immunoassay just by changing the polymer type? For this purpose, four different polymers, namely, polycaprolactone, poly lactic‐co‐glycolic acid, poly L‐lactic acid, and polyethersolfone were used as the based material for e.NFM fabrication. Results showed that compared with plain poly (dimethylsiloxane) surface of microchannels, poly lactic‐co‐glycolic acidand poly L‐lactic acid, which inherently contain end‐group of carboxyl in their chemical structure, can improve the protein immobilization, which leads to immunoassay signal enhancement through 1‐ethyl‐3‐(3‐dimethylaminopropyl)‐carbodiimide/N‐hydroxysuccinimide coupling chemistry, significantly.     

The potential of biomimetic nanofibrous electrospun scaffold comprising dual component for bone tissue engineering

Oils play a putative choice for alleviating various symptoms associated with bone-related disorders. In this present study, polyurethane (PU) scaffold encompassing with Mahua oil (MO) and propolis (PP) were developed using the electrospinning technique. Morphological analysis showed the reduction in the diameter of the electrospun scaffold with blending of MO and MO/PP into the PU matrix. The strong interactions between PU, MO, and PP were evident through the infrared spectrum and thermal analysis. The wettability results showed the hydrophobic nature in electrospun PU/MO scaffold and hydrophilic behavior in electrospun PU/MO/PP scaffold. Mechanical testing indicated the enhancement in the strength of the PU due to the addition of MO and PP. Moreover, the fabricated scaffolds exhibited nontoxicity, low hemoglobin release and improved blood clotting time as evident in the coagulation studies. The cell proliferation studies showed the enhanced fibroblast cell adhesion in the developed nanocomposites than the pristine PU. Hence, the fabricated PU scaffolds blended with MO and PP having desirable properties can serve as a valuable candidate for bone tissue repair.     

Synthesis and characterization of asymmetric polyethersulfone membranes: effects of concentration and polarity of nonsolvent additives on morphology and performance of the membranes

In this study, effects of methanol, ethanol and 1‐propanol as variable nonsolvent additives (NSAs) on the morphology and performance of flat sheet asymmetric polyethersulfone (PES) membranes were investigated. The membranes were prepared from PES/Polyvinylpyrrolidone (PVP)/N‐methyl‐2‐pyrrolidone (NMP) system via phase inversion. The obtained results indicate that with the addition of NSAs to the casting solution, the membrane morphology changes slowly from macrovoids to an asymmetric structure with finger‐like pores. By increasing the NSAs concentrations in the casting solution and decreasing their polarities, the membrane structure changes from finger‐like pores to sponge. The AFM and SEM images reveal that addition of NSA to the casting solution decreases the pore size of the prepared membranes and reduces the pure water flux and BSA solution flux, while increasing the protein rejection. Surface analysis of the membranes showed that mean pore size and surface porosity of the prepared membranes with NSAs in the casting solution are smaller compared with those of the membrane prepared with no NSA. Pure water flux and BSA solution flux through the membranes decrease and BSA rejection increases with increase in the concentration of NSAs and decrease in their polarity. Finally, it can be concluded that the T_g values of the PES membranes increase by addition of NSAs to the casting solution. Copyright © 2009 John Wiley & Sons, Ltd.     

Tensile deformation of electrospun nylon‐6,6 nanofibers

Nylon‐6,6 nanofibers were electrospun at an elongation rate of the order of 1000 s^?1 and a cross‐sectional area reduction of the order of 0.33 × 10⁵. The influence of these process peculiarities on the intrinsic structure and mechanical properties of the electrospun nanofibers is studied in the present work. Individual electrospun nanofibers with an average diameter of 550 nm were collected at take‐up velocities of 5 and 20 m/s and subsequently tested to assess their overall stress–strain characteristics; the testing included an evaluation of Young's modulus and the nanofibers' mechanical strength. The results for the as‐spun nanofibers were compared to the stress–strain characteristics of the melt‐extruded microfibers, which underwent postprocessing. For the nanofibers that were collected at 5 m/s the average elongation‐at‐break was 66%, the mechanical strength was 110 MPa, and Young's modulus was 453 MPa, for take‐up velocity of 20 m/s—61%, 150 and 950 MPa, respectively. The nanofibers displayed α‐crystalline phase (with triclinic cell structure). © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 1482–1489, 2006     

Improvement on physical properties of polyethersulfone membranes modified by poly(1‐vinylpyrrolidone) grafted magnetic Fe3O4@SiO2 nanoparticles

Polyethersulfone (PES) and poly(1‐vinylpyrrolidone) (PVP) were used to prepare ultrafiltration membranes with grafted Fe₃O₄ magnetic nanoparticles (PVP‐g‐Fe₃O₄@SiO₂). The structure of synthesized PVP‐g‐Fe₃O₄@SiO₂ was confirmed by FT‐IR and SEM analysis. Physical properties of blend membranes such as thermal resistance, Tensile strength, water uptake, and hydrophilicity were also investigated. Blended membranes of PES/PVP‐g‐Fe₃O₄@SiO₂ have exhibited higher thermal resistance due to increasing the modified nanoparticle content. The hydrophilicity of the synthesized PES/PVP‐g‐Fe₃O₄@SiO₂ membranes also improved by increasing the PVP‐g‐Fe₃O₄@SiO₂ content. As expected, increasing the hydrophilicity of blended membrane, caused enhancement of fouling resistance in membranes. Results showed that the content of PVP‐g‐Fe₃O₄@SiO₂ has different effects on the properties of synthesized composite membranes. Despite increasing the content of PVP‐g‐Fe₃O₄@SiO₂ has a negative effect on elongation, positive effects on maximum stress was observed. Moreover, the water uptake of synthesized membranes was significantly enhanced in comparison to other similar studies.     

Sulfonated silica‐based electrolyte nanocomposite membranes

New functionalized particles were prepared by attaching sulfonated aromatic bishydroxy compounds onto fumed silica surface. First, a bromophenyl group was introduced onto the silica surface by reaction of bromophenyltrimethoxysilane with fumed silica. Then, sulfonated bishydroxy aromatic compounds were chemically attached to the silica surface by nucleophilic substitution reactions. The structure of the modified silica was characterized by elemental analysis: ¹³C‐NMR, ²⁹Si‐NMR, and FTIR. Afterward, novel inorganic–organic electrolyte composite membranes based on sulfonated poly(ether ether ketone) have been developed using the sulfonated aromatic bishydroxy compounds chemically attached onto the fumed silica surface. The composite membrane prepared using silica with sulfonated hydroxytelechelic, containing 1,3,4‐oxadiazole units, has higher proton conductivity values in all range of temperatures (40–140 °C) than the membrane containing only the plain electrolyte polymer, while the methanol permeability determined by pervaporation experiment was unchanged. A proton conductivity up to 59 mS cm^?1 at 140 °C was obtained. The combination of these effects may lead to significant improvement in fuel cells (fed with hydrogen or methanol) at temperatures above 100 °C. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 2278–2298, 2006     

Facile fabrication and characterization of polyimide nanofiber reinforced photocured hybrid electrolyte for Li‐ion batteries

In this study, a novel ion conductive polyimide (PI) nanofiber reinforced photocured hybrid electrolyte has been fabricated. Polyimide fibers were fabricated with the reaction between 4,4′‐oxydianiline (ODA) and 3,3′,4,4′‐benzophenonetetracarboxylic dianhydride (BTDA) followed by electrospinning and thermal imidization methods. Then, PI electrospun fibers were dipped into hybrid resin formulation containing bisphenol A ethoxylate dimethacrylate (BEMA), poly (ethylene glycol) methyl ether methacrylate (PEGMA) and 3‐(methacryloyloxy) propyltrimethoxysilane (MEMO) and then photocured to prepare PI nanofiber reinforced electrolyte membrane. Photocured membranes were soaked into lithium hexafluorophosphate (LiPF₆) before measuring electrochemical stability and ionic conductivity of hybrid polyelectrolyte. The chemical structure and electrochemical performance of the electrolytes were examined by Fourier transform infrared (FTIR), thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), electrochemical impedance spectroscopy (EIS), linear sweep voltammetry (LSV) and scanning electron microscopy (SEM) analysis. The incorporation of MEMO into organic matrix effectively increased the modulus from 2.83 to 5.91 MPa. The obtained results showed that a suitable electrolyte for Li‐ion batteries with high lithium uptake ratio, high conductivity (7.2 × 10^?3 S cm^?1) at ambient temperature and wide stability window above 5.5 V had been prepared. Copyright © 2017 John Wiley & Sons, Ltd.     

Insights into the surface property and blood compatibility of polyethersulfone/polyvinylpyrrolidone composite membranes: toward high‐performance hemodialyzer

Applications of blood purification membranes are fuelled by diverse clinical needs, such as hemodialysis, hemodiafiltration, hemofiltration, plasmapheresis, and plasma collection. For clinical usage, the adding of polyvinylpyrrolidone (PVP) is the general protocol for the design of antifouling and antithrombotic properties integrated artificial membranes. In the present work, to insight into the detailed surface properties and blood compatibilities of the PVP blended composite membranes, we synthesized a series of PVP polymers with different molecular weights using reversible addition fragmentation chain transfer polymerization and designed a series of polyethersulfone (PES)/PVP composite membranes by a physically blending method. The effects of PVP molecular weights and blending ratios on the surface properties and the blood compatibilities of the composite membranes were investigated in detail. The surface attenuated total reflection Fourier transform infrared spectra and scanning electron microscopy pictures indicated that the PVP was successfully immobilized into the membranes, and the composite membranes exhibited morphology transformation from finger‐like structure to sponge‐like structure, which indicated that the composite membrane had tunable porosity and permeability by adding PVP. The blood compatible tests revealed that the composite membranes showed increased hydrophilicity, decreased plasma protein adsorption, suppressed platelet adhesion, and prolonged blood clotting time compared with pristine PES membrane. These results indicated that the PES/PVP composite membranes exhibited enhanced antifouling and antithrombotic properties than the pristine PES membrane. Meanwhile, the results also suggested that the composite membranes with larger molecular weight PVP and higher blending ratios might show better blood compatibility. Copyright © 2014 John Wiley & Sons, Ltd.     

Flexible electrospun PET/TiO2 nanofibrous structures: Morphology,thermal and mechanical properties

In this study, a solvothermal method was used to synthesize anatase titanium dioxide (TiO₂) nanoparticles in the presence of oleic acid (OA) and oleylamine (OM) as morphology‐directing agents. Functional nanocomposite fibers of poly(ethylene terephtalate) (PET) containing surfactants‐capped TiO₂ nanoparticles were developed by electrospinning technique. The morphology, thermal stability and mechanical properties of PET/TiO₂ nanocomposite mats were investigated as a function of TiO₂ concentration. Morphology investigation showed interesting results in terms of the level of TiO₂ dispersion inside the fibers and the improvement of the quality (smoothness) of the fibers' surface when the synthesized nanorhombic TiO₂ nanoparticles were used compared to a commercial P25 TiO₂ (AEROXIDE P25)_. The presence of OA and OM on the surface of the nanorhombic synthesized TiO₂ led to a significant improvement of TiO₂ dispersion inside the PET matrix. Furthermore, the physical interaction between the PET matrix and TiO₂ nanoparticles resulted in an enhanced thermal stability, and an increase of the Young's modulus and tensile strength for TiO₂ concentration up to 10 wt%.