Preparation and characterization of coaxial electrospun thermoplastic polyurethane/collagen compound nanofibers for tissue engineering applications

Collagen functionalized thermoplastic polyurethane nanofibers (TPU/collagen) were successfully produced by coaxial electrospinning technique with a goal to develop biomedical scaffold. A series of tests were conducted to characterize the compound nanofiber and its membrane in this study. Surface morphology and interior structure of the ultrafine fibers were characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM) and atomic force microscopy (AFM), whereas the fiber diameter distribution was also measured. The crosslinked membranes were also characterized by SEM. Porosities of different kinds of electrospun mats were determined. The surface chemistry and chemical composition of collagen/TPU coaxial nanofibrous membranes were verified by X-ray photoelectron spectroscopy (XPS) and Fourier transform infrared spectrometry (FTIR). Mechanical measurements were carried out by applying tensile test loads to samples which were prepared from electrospun ultra fine non-woven fiber mats. The coaxial electrospun nanofibers were further investigated as a promising scaffold for PIECs culture. The results demonstrated that coaxial electrospun composite nanofibers had the characters of native extracellular matrix and may be used effectively as an alternative material for tissue engineering and functional biomaterials.     

Double‐layered composite nanofibers and their mechanical performance

Continuous polymer nanofibers are available through electrospinning, but most have the same structure in their cross section. This article focuses on the fabrication and the structural and mechanical characterization of pencil‐like double‐layered composite nanofibers coaxially electrospun from solutions of two different biodegradable materials, i.e., gelatin and poly(ε‐caprolactone) (PCL). Transmission electron microscopy and water contact angle measurements confirmed that a gelatin inner fiber was wrapped with a PCL outer layer. Possible applications of such nanofibers include a controlled degradation rate when used as a medical device in human body. It has been found that the tensile performance of the composite nanofibers was better than those of both the pure constituent, i.e. gelatin and PCL, nanofibers alone. The ultimate strength and ultimate strain of the composite nanofibers with 7.5% w/v gelatin in the core and 10% w/v PCL as shell were at least 68% and 244% higher, respectively, than those of the same concentration pure gelatin and PCL nanofibers. Thus, a coaxial electrospinning technique as used in this article can be applicable, not only in developing functionalized nanofibers but also in elevating their mechanical property. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 2852–2861, 2005     

Microstructural Study of Nylon-6/Gelatin Composite Nanofibers

Electrospinning is a simple and effective technology for fabricating nanofibers and polymer blending provides strength and minimal defects of electrospun ones. Therefore, in the present study, fabrication, and characterization of nylon-6/gelatin electrospun nanofibers using low-toxic solvents was investigated as means to improve the morphological deficiencies of gelatin nanofibers and facilitate its electrospinnability. The morphology of electrospun nylon-6/gelatin nanofibers were characterized using scanning electron microscope (SEM). SEM results showed that electrospun blend nanofibers had smooth surface with average diameter of from 40 to 100 nm; while, the miscibility of the blend and thermal behavior of nanofibers were determined using Fourier transform-infrared spectroscopy (FTIR) and differential scanning calorimeter (DSC). Water contact-angle measurement (WCA) was employed to investigating the wettability of nanofibers.     

Electrospinning of carboxymethyl starch/poly(L‐lactide acid) composite nanofiber

Carboxymethyl starch (CMS) is a natural polymer derived from sago starch that is obtained from sago palm (Metroxylon spp.). Herein, CMS was used as a polysaccharide source in preparations of composite nanofibers with poly(L‐lactide acid) (PLLA). The incorporation of CMS with PLLA in nanofiber form has great potential to be used in biomedical applications. The composite PLLA/CMS nanofibers were fabricated by electrospinning technique at various ratios of CMS, which were 5, 10, 15, and 20% vol/vol. The composite nanofibers were characterized according to their physical morphology, chemical interaction, wettability, water uptake, and thermal and mechanical behaviors. The result showed that uniform and bead‐free nanofibers were produced at the low ratio of CMS while fractal and discontinuing fiber was observed at a high ratio of CMS. A better mechanical strength was obtained at low CMS ratio as compared with higher one. Fourier transform infrared results showed that there was an interaction between CMS and PLLA after electrospinning. The surface hydrophilicity and water uptake increased with increasing ratio of CMS. The results from the differential scanning calorimeter analysis showed the decrease of the glass transition (T_g) and cold crystallization temperature (T_cc) of the nanofiber after addition of CMS in PLLA.     

Polysulfone nanofibers prepared by electrospinning and gas/jet-electrospinning

Polysulfone nanofibers were prepared by electrospinning. The electrospinning equipment was designed in a new way, wherein the spinneret was combined with a gas jet device. The intrinsic viscosity of the used polysulfone was 0.197 dL/g in dimethyl acetamide, which was also the solvent in electrospinning. The gas used in this gas jet/electrostatic spinning was nitrogen. The relationship between the process parameters and the average diameter of polysulfone nanofibers was investigated. The main process parameters studied in this work were the voltage, the flow rate of the spinning fluid, the distance between the spinneret and the nanofiber collector and the temperature in the spinning chamber. The other important factors determining the nanometer diameter were the spinning fluid properties including its viscosity, surface tension and electrical conductivity. The average diameter and the diameter distribution of electrospinning nanofibers were measured experimentally by using scanning electron microscopy. The diameter of polysulfone nanofibers prepared by the gas jet/electrostatic spinning was in the range 50–500 nm. It was found that the diameter of nanofibers mainly depended on high voltage, the gap between the spinneret and the collector and the concentration of polymer solutions. It is concluded that the gas-jet/electrospinning is a better method than the conventional electrospinning, in that it makes the nanofibers finer and more uniform and exhibits higher efficiency in the process of electrospinning. __________ Translated from Acta Polymerica Sinica, 2005, (5) (in Chinese)     

Electrospinning of Nanofibers Based on Chitosan/Gelatin Blend for Antibacterial Uses

Chitosan/gelatin blend nanofibers were electrospun and the focus of this study was on the chitosan and gelatin concretions and on morphology of resulting nanofibers. The morphology of electrospun chitosan/gelatin blend nanofibers were characterized using scanning electron microscope (SEM). The miscibility of blend was determined using a SEM and Fourier transform infrared spectrometer/attenuated total reflectance (FTIR/ATR). Antibacterial property and stability of samples was also investigated. Water contact angle measurement (WCA) was employed to investigate the wettability of nanofibers.     

Fabrication of photo‐cross‐linked polyethyleneimine‐based barriers for CO2 capture

In this study, first, polyethyleneimine was acrylated and mixed with polyvinyl alcohol solution to prepare photo‐crosslinked polyethyleneimine (PEI)‐based nanofibers by utilizing ultraviolet and electrospinning technique at the same time. For CO₂ permeability testing, same formulations were prepared by using solvent casting technique and exposed to ultraviolet light to have polyethyleneimine‐based membrane films. The chemical structures of the nanofibers were characterized by Fourier transform infrared spectroscopy. The thermal properties of nanofibers were examined by thermal gravimetric analysis and differential scanning calorimeter. The morphology of nanofibers was investigated by scanning electron microscopy. CO₂ permeabilities of samples were also measured. Copyright © 2015 John Wiley & Sons, Ltd.     

Synthesis and mechanical properties of para‐aramid nanofibers

Scalable, bottom‐up chemical synthesis and electrospinning of novel Cl‐substituted poly(para‐phenylene terephthalamide) (PPTA) nanofibers are herein reported. To achieve Cl‐PPTA nanofibers, the chemical reaction between the monomers was precisely controlled, and dissolution of the polymer into solvent was tailored to enable anisotropic solution formation and sufficient entanglement molecular weight. Electrospinning processing parameters were studied to understand their effects on fiber formation and mat morphology and then optimized to yield consistently high quality fibers. Importantly, the control of relative humidity during the fiber formation process was found to be critical, likely because water promotes hydrogen bond formation between the PPTA chains. The fiber and mat morphologies resulting from different combinations of chemistry and spinning conditions were observed using scanning electron microscopy, and observations were used as inputs to the optimization process. Tensile properties of single Cl‐PPTA nanofibers were characterized for the first time using a nanomanipulator mounted inside a scanning electron microscope (SEM), and fiber moduli measuring up to 70 GPa, and strengths exceeding 1 GPa were achieved. Given the excellent mechanical properties measured for the nanofibers, this chemical synthesis procedure and electrospinning protocol appear to be a promising route for producing a new class of nanofibers with ultrahigh strength and stiffness. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2019 , 57, 563–573     

Preparation of polyamide-6/chitosan composite nanofibers by a single solvent system via electrospinning for biomedical applications

This work was focused on preparation and characterizations of chitosan blended polyamide-6 nanofibers by a new single solvent system via electrospinning process for human osteoblastic (HOB) cell culture applications. The morphological, structural and thermal properties of the polyamide-6/chitosan nanofibers were analyzed by using field-emission scanning electron microscopy (FE-SEM), X-ray diffraction (XRD), Fourier transform-infrared (FT-IR) spectroscopy, Raman spectroscopy, differential scanning calorimetry (DSC) and thermogravimetry (TGA). SEM images revealed that the nanofibers were well-oriented and had good incorporation of chitosan. FT-IR results indicated that the amino groups of chitosan existed in the blended nanofibers. TGA analysis revealed that the onset degradation temperature was decreased with increasing chitosan content in the blended nanofibers. The morphological features of the cells attached on nanofibers were confirmed by SEM. The adhesion, viability and proliferation properties of osteoblast cells on the polyamide-6/chitosan blended nanofibers were analyzed by in vitro cell compatibility test.     

静电纺丝法制备La0.67Ba0.33MnO3微纳米纤维及其红外发射率研究

采用静电纺丝法结合溶胶-凝胶技术制备了钙钛矿型La_0.67Ba_0.33MnO₃微纳米纤维, 并利用差示扫描量热-热失重分析(DSC-TGA)、 X射线衍射(XRD)、 傅里叶变换红外光谱(FTIR)和扫描电子显微镜(SEM)等技术对产物进行了表征, 利用IR-2红外发射率测试仪测试了La_0.67Ba_0.33MnO₃在280~370 K范围内的红外发射率. 结果表明, La_0.67Ba_0.33MnO₃在600 ℃时已形成钙钛矿结构. 随着煅烧温度的升高, La_0.67Ba_0.33MnO₃的形貌由纤维状向三维网络状转变, 并最终失去纤维形态. 在280~370 K范围内, La_0.67Ba_0.33MnO₃微纳米纤维的红外发射率随温度升高而升高, 由0.564增加至0.689. 利用钙钛矿材料双交换理论解释了这一现象, 并进一步探讨了其在红外发射率可变材料中的应用前景.     

Electrospinning of chitosan derivative nanofibers with structural stability in an aqueous environment

We report a simple method to produce stable chitosan derivative nanofibers via electrospinning. A chitosan solution with lactate salt was electrospun to produce nanofibers, followed by thermal treatment to enhance fiber stability. Chemical and morphological analyses demonstrated that the resulting nanofibers were crosslinked via amidation between chitosan and lactate salt. These fibers exhibited sustained morphological and structural stabilities to serve as a scaffold for biomedical applications.     

Highly porous core-shell polymeric fiber network

Core-shell nanofibers are of great interest in the field of tissue engineering and cell biology. We fabricated porous core-shell fiber networks using an electrospinning system with a water-immersed collector. We hypothesized that the phase separation and solvent evaporation process would enable the control of the pore formation on the core-shell fiber networks. To synthesize porous core-shell fiber networks, we used polycaprolactone (PCL) and gelatin. Quantitative analysis showed that the sizes of gelatin-PCL core-shell nanofibers increased with PCL concentrations. We also observed that the shapes of the pores created on the PCL fiber networks were elongated, whereas the gelatin-PCL core-shell fiber networks had circular pores. The surface areas of porous nanofibers were larger than those of the nonporous nanofibers due to the highly volatile solvent and phase separation process. The porous core-shell fiber network was also used as a matrix to culture various cell types, such as embryonic stem cells, breast cancer cells, and fibroblast cells. Therefore, this porous core-shell polymeric fiber network could be a potentially powerful tool for tissue engineering and biological applications.     

Process optimization and empirical modeling for electrospun polyacrylonitrile (PAN) nanofiber precursor of carbon nanofibers

Ultrafine fibers were spun from polyacrylonitrile (PAN)/N,N-dimethyl formamide (DMF) solution as a precursor of carbon nanofibers using a homemade electrospinning set-up. Fibers with diameter ranging from 200 nm to 1200 nm were obtained. Morphology of fibers and distribution of fiber diameter were investigated varying concentration and applied voltage by scanning electric microscopy (SEM). Average fiber diameter and distribution were determined from 100 measurements of the random fibers with an image analyzer (SemAfore 5.0, JEOL). A more systematic understanding of process parameters was obtained and a quantitative relationship between electrospinning parameters and average fiber diameter was established by response surface methodology (RSM). It was concluded that concentration of solution played an important role to the diameter of fibers and standard deviation of fiber diameter. Applied voltage had no significant impact on fiber diameter and standard deviation of fiber diameter.     

Fabrication and chemical crosslinking of electrospun <Emphasis Type="Italic">trans</Emphasis>-polyisoprene nanofiber nonwoven

In this work, the optimal electrospinning conditions of trans-polyisoprene (TPI) solutions were evaluated nevertheless its lower glass transition temperature than the room temperature. Subsequently, chemical crosslinking of TPI nonwovens was firstly investigated by vulcanizing at high temperatures in the case of the persistence of nanofiber structure. For this purpose, curing agents of TPI were embedded in TPI nanofibers by co-electrospinning, and then a protect layer was coated on TPI nanofibers by filtering gelatin solution going through TPI nonwoven before the vulcanization at 140?160 °C. The results showed that the vulcanization of TPI fibrous nonwoven at high temperatures did not destroy the fiber morphology. Interestingly, TPI fibrous nonwovens after vulcanization showed excellent mechanical properties (~17 MPa of tensile strength) that could be comparable to or even higher than that of some bulk rubber materials.     

Fabrication and Photocatalytic Properties of Water-stable Ag/PW12/PVA Nanocomposites

A kind of water-stable phosphotungstic acid/polyvinyl alcohol(PW₁₂/PVA) fiber was prepared by thermal or chemical crosslinking treatments with the help of electrospinning, and silver nanoparticles(NPs) modified fibrous precursor was successfully obtained by photoreduced method. The nanocomposites were characterized by transformation infrared spectroscopy(FTIR), UV-Vis diffuse reflection spectroscopy(DRS), field environmental scanning electron microscopy(FE-SEM), transmission electron microscopy(TEM) and X-ray photoelectron spectroscopy(XPS). The results indicate that the sizes of silver NPs are about 20 or 40 nm on thermally or glutaraldehyde(GA) vapor crosslinked PW₁₂/PVA fiber, respectively. As a photocatalyst, PW₁₂/PVA fiber possesses high surface area to volume ratio, stable recyclability, and efficient transportation of electrons under visible light. The nanohybrids exhibit excellent photocatalytic activity for the degradation of Rhodamin B than PW₁₂/PVA nanofiber.     

Optical birefringence and molecular orientation of electrospun polycaprolactone fibers by polarizing-interference microscopy

The potential of polarizing-interference Pluta microscope for determination of optical birefringence of individual nanofibers formed by electrospinning was shown. This technique can be applied for measurements of fiber birefringence, practically at diameter above 300 nm. The molecular orientation of individual polycaprolactone (PCL) nanofibers was determined from birefringence assuming the same orientation of both phases, crystal and amorphous. The molecular orientation was determined using DSC crystallinity, crystal intrinsic birefringence calculated for the first time for PCL from bond polarizabilities as well as estimated value of amorphous intrinsic birefringence. Our results indicate that the birefringence and thus molecular orientation are strongly inhomogeneous along the nanofibers, reflecting a complex nature of forces acting during electrospinning process. The average molecular orientation is weak if any, being dependent together with fiber thickness and crystallinity on electrospinning parameters, like applied voltage, concentration and type of solvent. The obtained results indicate that the average molecular orientation displays similar dependence on applied voltage as fiber diameter. Relatively low melting temperature of electrospun nanofibers suggests low crystal size and/or high concentration of defects in crystals. This observation corresponds with low crystallinity and molecular orientation, indicating together relatively low degree of crystal ordering due to high rate of cooling and solvent evaporation during electrospinning, limiting thus crystallization process.     

聚乙烯醇明胶混合水溶液的静电纺丝

将聚乙烯醇与明胶混合水溶液进行静电纺丝,制备了聚乙烯醇与明胶混合超细纤维及其电纺膜,研究了混合纺丝液的组成对纺丝液的粘度、表面张力和电导率的影响,观察了纤维的微观形貌,并对电纺膜进行了差示扫描量热测定.结果表明:当混合液中明胶含量小于20 9/6时,静电纺丝可以稳定进行.随着明胶含量由5%逐渐增加至25%,混合超细纤维的平均直径先是由260nm逐渐下降至207 nm而后又逐渐增加至320 nm.明胶的含量低于15%时,不影响其混合电纺膜中PVA的结晶.     

Controlled Nanofiber Composed of Multi‐Wall Carbon Nanotube/Poly(Ethylene Oxide)

We have successfully fabricated poly(ethylene oxide) (PEO) nanofibers containing embedded multi‐wall carbon nanotubes (MWCNTs). An initial dispersion of the MWCNTs in distilled water was achieved using sodium dodecyl sulfate. Subsequently, the dispersion was decanted into a PEO solution, which enabled separation of the MWCNTs and their individual incorporation into the PEO nanofibers on subsequent electrospinning. Initially, the carbon nanotube (CNT) rods were randomly oriented, but owing to the sink‐like flow in the electrospinning wedge, they became gradually oriented along the streaming direction, in order that oriented CNTs were obtained on entering the electrospun jet. Individual MWCNTs became embedded in the nanofibers, and were mostly aligned along the fiber axis. Evidence of load transfer to the nanotubes in the composite nanofiber was observed from the field‐emission scanning electron microscopy, transmission electron microscopy and conductivity data.     

The Development of Genipin‐Crosslinked Poly(caprolactone) (PCL)/Gelatin Nanofibers for Tissue Engineering Applications

Composite nanofibers of poly(caprolactone) (PCL) and gelatin crosslinked with genipin are prepared. The contact angles and mechanical properties of crosslinked PCL‐gelatin nanofibers decrease as the gelatin content increases. The proliferation of myoblasts is higher in the crosslinked PCL‐gelatin nanofibers than in the PCL nanofibers, and the formation of myotubes is only observed on the crosslinked PCL‐gelatin nanofibers. The expression level of myogenin, myosin heavy chain, and troponin T genes is increased as the gelatin content is increased. The results suggest that PCL‐gelatin nanofibers crosslinked with genipin can be used as a substrate to modulate proliferation and differentiation of myoblasts, presenting potential applications in muscle tissue engineering.