Study of supramolecular side‐chain and cross‐linking polymers by complexation of various H‐donor acids with H‐acceptor copolymers containing pendent carbazole and fluorescent pyridyl units

Two H‐bonded acceptor (H‐acceptor) homopolymers 14 and 17 were successfully prepared by polymerization of fluorescent pyridyl monomers PBT and PBOT ( 12 and 13 ), which were synthesized via Sonogashira coupling and Wittig‐Horner reactions. To increase the glass transition temperatures as well as reduce the π‐π stacking of the photoluminescent (PL) H‐acceptor copolymers and their H‐bonded polymer complexes, fluorescent monomers 12 and 13 were copolymerized with N‐vinylcarbazole monomer CAZ (23) to produce H‐acceptor copolymers 15–16 and 18–19 . Supramolecular side‐chain and crosslinking polymers (i.e., H‐bonded polymer complexes) obtained by complexation of light‐emitting H‐acceptor polymers 14–19 with various proton donor (H‐donor) acids 20–22 were further characterized by DSC, POM, FTIR, XRD, and PL measurements. The mesomorphic properties can be tuned from the nematic phase in H‐acceptor homopolymers ( 14 and 17 ) to the tilted smectic C phase in their H‐bonded polymer complexes ( 14/20–21 and 17/20–22 ) by the introduction of H‐donor acids (20–22). Moreover, the PL properties of light‐emitting H‐acceptor polymers can be adjusted not only by the central structures of the conjugated pyridyl cores but also by their surrounding nonfluorescent H‐donor acids. In general, redder shifts of PL emissions in H‐bonded polymer complexes occurred when the light‐emitting H‐acceptor polymers were complexed with H‐donors having smaller pKa values. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 2734–2753, 2009     

Synthesis and optical properties of green‐light‐emitting copolymers containing side‐chain oxadiazole units

Atom transfer radical polymerization was used to prepare well‐defined vinyl polyoxadiazole homomacromonomers with a properly modified α‐dicarboxylic acid methyl ester as the initiator. Macromonomers of various molecular weights with narrow polydispersities in some cases were obtained, as proved by gel permeation chromatography (GPC). The structures of the obtained macromonomers were then identified with ¹H NMR spectroscopy. These macromonomers were subsequently copolymerized with a dihydroxy anthracene based monomer by a polycondensation technique, and this resulted in polymacromonomers. Coil–rod–coil copolymers containing side‐chain anthracene and oxadiazole units were also synthesized by atom transfer radical polymerization. The resulting copolymers combined an anthracene derivative as the rigid block with a random copolymer of the desired anthracene‐ and/or oxadiazole‐based monomers as the flexible block. These copolymers were primarily characterized with GPC and ¹H NMR techniques. Additionally, the optical properties of all these copolymers were investigated in detail, and they suggested energy transfer from the oxadiazole to the anthracene chromophores, which became much more efficient in the solid state. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 1049–1061, 2005     

Supramolecular assembly of H‐bonded side‐chain polymers containing conjugated pyridyl H‐acceptor pendants and various low‐band‐gap H‐donor dyes bearing cyanoacrylic acid groups for organic solar cell applications

Novel supramolecular side‐chain polymers were constructed by complexation of proton acceptor (H‐acceptor) polymers, i.e., side‐chain conjugated polymers P1–P2 containing pyridyl pendants, with low‐band‐gap proton donor (H‐donor) dyes S1–S4 (bearing terminal cyanoacrylic acids) in a proper molar ratio. Besides unique mesomorphic properties confirmed by DSC and XRD results, the H‐bonds of supramolecular side‐chain structures formed by pyridyl H‐acceptors and cyanoacrylic acid H‐donors were also confirmed by FTIR measurements. H‐donor dyes S1–S4 in solid films exhibited broad absorption peaks located in the range of 471–490 nm with optical band‐gaps of 1.99–2.14 eV. Furthermore, H‐bonded polymer complexes P1/S1–P1/S4 and P2/S1–P2/S4 exhibited broad absorption peaks in the range of 440–462 nm with optical band‐gaps of 2.11–2.25 eV. Under 100 mW/cm² of AM 1.5 white‐light illumination, the bulk heterojunction polymer solar cell (PSC) devices containing an active layer of H‐bonded polymer complexes P1/S1–P1/S4 and P2/S1–P2/S4 (as electron donors) mixed with [6,6]‐phenyl C₆₁ butyric acid methyl ester (i.e., PCBM, as an electron acceptor) in the weight ratio of 1:1 were investigated. The PSC device containing H‐bonded polymer complex P1/S3 mixed with PCBM (1:1 w/w) gave the best preliminary result with an overall power conversion efficiency (PCE) of 0.50%, a short‐circuit current of 3.17 mA/cm², an open‐circuit voltage of 0.47 V, and a fill factor of 34%. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 5998–6013, 2009     

Synthesis and electro‐optical properties of light‐emitting polymers containing oxadiazole derivatives for light‐emitting diodes applications

Two PPV‐based bipolar polymers containing 1,3,4‐oxadiazole pendant groups were synthesized via the Gilch polymerization reaction for use in light‐emitting diodes (LEDs). The resulting polymers were characterized using ¹H and ¹³C NMR, elemental analysis, DSC, and TGA. These polymers were found to be soluble in common organic solvents and are easily spin‐coated onto glass substrates, producing high optical quality thin films without defects. The electro‐optical properties of ITO/PEDOT/polymer/Al devices based on these polymers were investigated using UV‐visible, PL, and EL spectroscopy. The turn‐on voltages of the OC₁Oxa‐PPV and OC₁₀Oxa‐PPV devices were found to be 8.0 V. The maximum brightness and luminescence efficiency of the OC₁Oxa‐PPV device were found to be 544 cd/m² at 19 V and 0.15 cd/A, respectively. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 1098–1110, 2008     

Single layer light‐emitting diodes from copolymers comprised of mesogen‐jacketed polymer containing oxadiazole units and PVK

A series of copolymers PCt‐co‐Poly(N‐vinylcarbazole) were synthesized through common radical polymerization, in which P‐Ct as a kind of mesogen‐jacketed liquid crystalline polymer was introduced, and the effects of copolymers composing variation on the optical properties of the polymers were studied. The structures and properties of the copolymers were characterized and evaluated by thermogravimetric (TGA), UV, photoluminescence (PL), cyclic voltammetry (CV), and electroluminescence (EL) analyses. All the polymers enjoy high thermal stability. PL peaks in the film show blue‐shift compared with in solutions and fluorescent quantum efficiency decreased with the N‐vinylcarbazole (nvk) content increasing, which supported the efficient energy transfer from nvk units to the oxadiazole units. CV revealed that, with the incorporation of nvk to the copolymer, these copolymers had high‐lying HOMO energy levels ranging from ?5.94 to ?6.09 eV. Single‐layer light‐emitting diodes (LEDs) with the configuration of ITO/PEDOT/PCt‐nvk/Mg:Ag/Ag were fabricated, which emit a blue light around 450 and 490 nm with a maximum luminance of 703 cd/m². The device performance varies with the content of nvk and device configuration, with device configuration ( b ) and PCt‐nvk8 giving the best value of external quantum efficiency of 0.27%. We show here that by proper design copolymer structure and modification of device configuration can exhibit strong blue EL in higher external quantum efficiency. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 1843–1851, 2008     

Controlled synthesis and microstructure tuning of PEG‐containing side‐chain discotic liquid crystalline block copolymers via RAFT polymerization

Liquid crystalline block copolymers (LCBCPs) are fascinating for their combining molecular level liquid crystalline orders and microphase separated multidomain morphologies. Here in this article, a series of PEG‐containing side‐chain discotic LCBCPs of PEG‐b‐P_m‐n with variant spacer length m = 6, 10 and degree of polymerization (DP) of discotic LC block from n = 10 to 45, have been well‐synthesized via reversible addition‐fragmentation chain‐transfer (RAFT) polymerization. The RAFT process mediated by macromolecular chain transfer agent (macroCTA) shows remarkable monomer concentration dependence. The influence of the introduced PEG block on the nano‐scale microphase‐segregation and mesophase organization is closely related to the side‐chain triphenylene (TP) discogens stacking mode dependent on the spacer length. Wherein, the PEG‐b‐P₆‐n series with a six‐methylene spacer exhibit consistent microphase separation with slightly disturbed yet ordered columnar structures. While for PEG‐b‐P₁₀‐n series with a longer ten‐methylene spacer, the columnar organization in the copolymers is even improved in contrast with the low order of randomly TP stacking in their corresponding homopolymers. This work offers a viable and inspiring pathway for controlled synthesis of block copolymers with bulky side groups, as well as enhances in‐depth understanding of the hierarchical superstructure organization in discotic units involved complex block copolymers. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55, 2544–2553     

Self‐assembly of amphiphilic ABA random triblock copolymers in water

Self‐assembly of amphiphilic ABA random triblock copolymers in water serves as a novel approach to create unique structure micelles connected with flexible linkages. The ABA triblock copolymers consist of amphiphilic random copolymers bearing hydrophilic poly(ethylene glycol) and hydrophobic dodecyl pendants as the A segments and a hydrophilic poly(ethylene oxide) (PEO) as the middle B segment. The A block is varied in dodecyl methacrylate content of 20%–50% and degree of polymerization (DP) of 100‐200. By controlling the composition and DP of the A block, various architectures can be tailor‐made as micelles in water: PEO‐linked double core unimer micelles, PEO‐looped unimer or dimer micelles, and multichain micelles. Those PEO‐linked or looped micelles further exhibit thermoresponsive solubility in water. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019 , 57, 313–321     

Self‐assembly of metallo‐supramolecular block copolymers in thin films

The self‐assembly of a metallo‐supramolecular PS‐[Ru]‐PEO block copolymer, where ‐[Ru]‐ is a bis‐2,2′:6′,2″‐terpyridine‐ruthenium(II) complex, in thin films was investigated. Metallo‐supramolecular copolymers exhibit a different behavior as compared to their covalent counterparts. The presence of the charged complex at the junction of the two blocks has a strong impact on the self‐assembly, effecting the orientation of the cylinders and ordering process. Poly(ethylene oxide) cylinders oriented normal to the film surface are obtained directly regardless of the experimental conditions over a wide range of thicknesses. Exposure to polar solvent vapors can be used to improve the lateral ordering of the cylindrical microdomains. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 4719–4724, 2008     

Self‐Assembly in Helical Columnar Mesophases and Luminescence of Chiral 1H‐Pyrazoles

Chiral polycatenar 1H‐pyrazoles self‐assemble to form columnar mesophases that are stable at room temperature. X‐ray diffraction and CD studies in the mesophase indicate a supramolecular helical organization consisting of stacked H‐bonded dimers. The liquid‐crystalline compounds reported are 3,5‐bis(dialkoxyphenyl)‐1H‐pyrazoles that incorporate two or four dihydrocitronellyl chiral tails. It can be observed that the grafting of these branched chiral substituents onto the 3,5‐diphenyl‐1H‐pyrazole core has a beneficial role in inducing mesomorphism, because isomeric linear‐chain compounds are not liquid crystalline; this is not the usual scheme of behavior. Furthermore, the molecular chirality is transferred to the columnar mesophase, because preferential helical arrangements are observed. Films of the compounds are luminescent at room temperature and constitute an example of the self‐organization of nondiscoid units into columnar liquid‐crystalline assemblies in which the functional molecular unit transfers its properties to a hierarchically built superstructure.     

Conjugated and partially conjugated 2,5‐diphenylthiophene‐containing light‐emitting copolymers in polymeric light‐emitting diode (PLED) device fabrications

To study the effect of nonconjugation on polymeric and photophysical properties of thiophene‐containing polymers, new light‐emitting copolymers comprising either alternate 2,5‐diphenylthiophene and vinylene or alternate 2,5‐diphenylthiophene and aliphatic ether segments were synthesized. Both copolymers contained 2,5‐diphenylthiophene as the major chromophore and emitted a sky bluish fluorescence in dilute solution (10^?2 mg/mL). With a rigid and planarity structure and the concomitant crystallinity, the former copolymer (fully conjugated) possessed a higher quantum efficiency, a higher glass‐transition temperature, and a better thermal stability. In contrast, the latter copolymer (conjugated–nonconjugated) had better solubility and provided enhanced photophysical properties for the fabricated polymeric light‐emitting diode (PLED) device: at 15 V, the maximum current and brightness were 110 mA/cm² and 4289 cd/m², respectively, and the electroluminescence efficiency remained constant at approximately 4.9 cd/A in a voltage range of 8 to 14 V. The existence of intramolecular/intermolecular aggregates in the latter copolymer was corroborated from the the UV–vis and photoluminescence spectra of its solutions. With an increase in solution concentration, the shape and λ_max of the photoluminescence spectrum were redshifted. In a solution with a concentration as high as 10 mg/mL, the redshift was so drastic that the photoluminescence spectrum was nearly identical to that of a solid‐film. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 6061–6070, 2004     

Cascade hole transport in efficient green phosphorescent light‐emitting devices achieved by layer‐by‐layer solution deposition using photocrosslinkable‐conjugated polymers containing oxetane side‐chain moieties

A hole‐injection/transport bilayer structure on an indium tin oxide (ITO) layer was fabricated using two photocrosslinkable polymers with different molecular energy levels. Two photoreactive polymers were synthesized using 2,7‐(or 3,6‐)‐dibromo‐9‐(6‐((3‐methyloxetan‐3‐yl)methoxy)hexyl)‐9H‐carbazole) and 2,4‐dimethyl‐N,N‐bis(4‐ (4,4,5,5‐tetramethyl‐1,3,2‐dioxaborolan‐2‐yl)phenyl)aniline via a Suzuki coupling reaction. When the oxetane groups were photopolymerized in the presence of a cationic photoinitiator, the photocured film showed good solvent resistance and compatibility with a poly(N‐vinylcarbazole) (PVK)‐based emitting layer. Without the use of a conventional hole injection layer (HIL) of poly(3,4‐ethylenedioxythiophene)/(polystyrenesulfonate) (PEDOT:PSS), the resulting green light‐emitting device bearing PVK: 5‐4‐tert‐butylphenyl‐1,3,4‐oxadiazole (PBD):Ir(Cz‐ppy)3 exhibited a maximum external quantum efficiency of 9.69%; this corresponds to a luminous efficiency of 29.57 cd/A for the device K‐4 configuration ITO/POx‐I/POx‐II/PVK:PBD:Ir(Cz‐ppy)3/triazole/Alq3/LiF/Al. These values are much higher than those of PLEDs using conventional PEDOT:PSS as a single HIL. The significant improvement in device efficiency is the result of suppression of the hole injection/transport properties through double‐layered photocrosslinked‐conjugated polymers. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Self‐assembly of supramolecular polymers into tunable helical structures

There is growing interest in the design of synthetic molecules that are able to self‐assemble into a polymeric chain with compact helical conformations, which is analogous to the folded state of natural proteins. Herein, we highlight supramolecular approach to the formation of helical architectures and their conformational changes driven by external stimuli. Helical organization in synthetic self‐assembling systems can be achieved by the various types of noncovalent interactions, which include hydrogen bonding, solvophobic effects, and metal‐ligand interactions. Since the external environment can have a large influence on the strength and configuration of noncovalent interactions between the individual components, stimulus‐induced alterations in the intramolecular noncovalent interactions can result in dynamic conformational change of the supramolecular helical structure thus, driving significant changes in the properties of the materials. Therefore, these supramolecular helices hold great promise as stimuli‐responsive materials. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 1925–1935, 2008     

Self‐assembly of a triblock terpolymer mediated by hydrogen‐bonded complexes

A poly(methyl methacrylate)‐block‐poly(4‐vinylpyridine)‐block‐polystyrene (PMMA‐b‐P4VP‐b‐PS) triblock terpolymer is synthesized by ATRP to study its self‐assembly with PAA in organic solvents. The self‐assembly behavior of this system is compared with the one of a mixture of two diblocks, namely polystyrene‐block‐poly(4‐vinylpyridine) (PS‐b‐P4VP) and poly(methyl methacrylate)‐block‐poly(methacrylic acid) (PMMA‐b‐PMAA). For both systems, formation of hydrogen‐bonded complexes between the P4VP and PMAA or PAA blocks occurs. These complexes become insoluble in the solvent used and micelles with a P4VP/P(M)AA complexes core surrounded by PS and PMMA coronal chains are obtained in both cases. These micelles are analyzed by DLS and TEM. Spherical micelles are formed for both systems but the hydrodynamic radii obtained for the two types of micelles are different. Indeed, the micelles formed by the PMMA‐b‐P4VP‐b‐PS + PAA system are smaller than those observed for the PS‐b‐P4VP + PMMA‐b‐PMAA system. Finally, the effect of the molar ratio of the P4VP/PMAA complexing blocks is investigated. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 459–467     

Incorporation of a conjugated side‐chain in regioregular polythiophenes: Chiroptical properties and selective oxidation

The synthesis, aggregation, and optical properties of a chiral, regioregular polythiophene, substituted with a conjugated substituent, are described. The polymer was prepared using a Stille coupling reaction. The fact that the side‐chain contributes to the absorption (UV‐vis), emission (fluorescence), and redox behavior (cyclic voltammetry) of the material demonstrates that the substituent contributes to the electronic properties. It was shown that the conjugated side‐chain chirally stacks in conditions in which the polymer backbone aggregates, which demonstrates the ability of conjugated polymers to induce a (chiral) lamellar organization of conjugated moieties, present in their side‐chain. The aggregation of both the side‐chain and the backbone was monitored using UV‐vis and CD spectroscopy. Finally, it is shown that the conjugated side‐chain can selectively be oxidized, without oxidizing the polythiophene backbone. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 1891–1900, 2009     

Synthesis and optical properties of light‐emitting π‐conjugated polymers containing biphenyl and dithienosilole

Copolymers containing oligo(phenylene vinylene) (2.5), fluorene, and 4,4‐dihexyldithienosilole (DTS) units were synthesized and characterized. The π‐conjugated monomers were joined with the palladium(0)‐catalyzed Suzuki–Miyaura coupling reaction, thus forming either biphenyl– or phenyl–thiophene linkages. These polymers were photoluminescent, with the fluorescent quantum efficiency between 54 and 63% and with λ_max for fluorescence at ～448 nm in tetrahydrofuran. The presence of 5% DTS in the copolymers had little influence on the optical absorption and emission wavelengths. Double‐layer light‐emitting‐diode devices using these polymers as emissive layers had low turn‐on voltages (3.5–4 V) and moderate external quantum efficiencies (0.14–0.30%). The results show that DTS plays a positive role in improving the charge‐injection characteristics of poly(phenylene vinylene) materials. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 2048–2058     

Synthesis and characterization of fluorene‐based copolymers containing benzothiadiazole derivative for light‐emitting diodes applications

Five new thermally robust electroluminescent fluorene‐based conjugated copolymers, including poly[2,7‐(9,9‐dioctylfluorene)‐co‐4,7‐{5,6‐bis(3,7‐dimethyloctyloxymethyl)‐2,1,3‐(benzothiadiazole)}] ( PFO‐P2C₁₀BT ) were synthesized and used to fabricate the efficient polymer light‐emitting diodes (PLEDs). The glass transition temperatures of the polymers were found to be higher than that of poly(9,9‐dialkylfluorenes) and are in the range 113–165 °C. We fabricated PLEDs in indium‐tin oxide/PEDOT/light‐emitting polymer/cathode configurations using either double‐layer LiF/Al or triple‐layer Alq₃/LiF/Al cathode structures. The new copolymers were found to have emission colors that vary from greenish blue (491 nm) to green (543 nm) depending on the copolymer composition. The maximum brightness and luminance efficiency of these PLEDs were found to be up to 5347 cd/m² and 1.51 cd/A at 10 V, respectively. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 6762–6769, 2008     

Novel 9,9′‐(1,3‐phenylene)bis‐9H‐carbazole‐containing copolymers as hole‐transporting and host materials for blue phosphorescent polymer light‐emitting diodes

Novel photo‐crosslinkable hole‐transport and host materials incorporated into multilayer blue phosphorescent polymer light‐emitting diodes (Ph‐PLEDs) were demonstrated in this study. The oxetane‐containing copolymers, which function as hole‐transport layers (HTL), could be cured by UV irradiation in the presence of a cationic photoinitiator. The composition of the two monomers was varied to yield three different hole‐transporting copolymers, [Poly(9,9′‐(5‐(((4‐(7‐(4‐(((3‐methyloxetan‐3‐yl)methoxy)methyl)phenyl)octan‐3‐yl)benzyl)oxy)methyl)?1,3‐phenylene)bis(9H‐carbazole)) ( P(mCP‐Ox)‐I , ‐II , and ‐III )]. In addition, monomer 1 was copolymerized with styrene to produce copolymer P(mCP‐Ph) as a host material for bis[2‐(4,6‐difluorophenyl)pyridinato‐C²,N](picolinato)iridium(III) (FIrpic), a blue‐emitting dopant. All mCP‐based copolymers displayed high glass transition temperatures (T_g) of up to 130–140 °C and triplet energies of up to 3.00 eV. The blue Ph‐PLEDs exhibited a maximum external quantum efficiency of 2.55%, in addition to a luminous efficiency of 8.75 cd A^?1 when using the device configuration of indium tin oxide/poly(3,4‐ethylenedioxythiophene):poly(styrene sulfonate)/ P(mCP‐OX)‐III / P(mCP‐Ph) :FIrpic(15 wt %)/3,3′‐[5′‐[3‐(3‐pyridinyl)phenyl][1,1′:3′,1′′‐terphenyl]‐3,3′′‐diyl]bispyridine/LiF/Al. The device bearing P(mCP‐Ox)‐III HTL, containing the highest composition of mCP unit, exhibited better performance than the other devices, which is attributed to induction of more balanced charge carriers and carrier recombination in the emissive layer. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 707–718     

Synthesis and characterization of new carbazole/fluorene‐based derivatives for blue‐light‐emitting devices

2,7‐Bis(9‐ethylcarbazol‐3‐yl)‐9,9‐di(2‐ethylhexyl)fluorene and a segmented copolymer composed of the same chromophores alternated with hexamethylene fragments were synthesized. The obtained materials possess good solubility in common organic solvents, high thermal stability with 1% weight loss temperature of 350–370 °C, and suitable glass transition temperatures. Both derivatives show blue fluorescence in dilute solutions as well as in solid state, demonstrating that excimers are not formed in the thin films. The fluorescence spectra of the materials do not show any peaks in the long‐wavelength region even after annealing at 200 °C in air. An organic LED with the configuration of ITO/copolymer/Al generates blue electroluminescence with the maximum peak at 416 nm, rather low turn‐on voltage (4.0 V), and brightness of about 400 cd/m². The heterostructure device based on model derivative emitted stable blue light with low operation voltage (100 cd/m² at ～11 V) and demonstrated luminescence efficiency of 0.8 cd/A. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 5987–5994, 2006