Modification of electro-optical properties of polymer dispersed liquid crystal films by iniferter polymerization

In this letter, iniferter polymerization was employed to prepare polymer dispersed liquid crystal (PDLC) films. Polystyrene (PS) was prepared as a macro-iniferter (MI). With the addition of MI in PDLC films, poly(methyl acrylate)-b-polystyrene was prepared in situ and used as polymer matrix in photopolymerization induced phase separation (PIPS). A reduction in driving voltages and an improvement in the ON state transmittance were observed for the sample prepared with a small amount of MI; while a poor electro-optical performance was obtained for that without any MI. Moreover, molecular weight and refractive index of the polymer matrix could be easily adjusted by the concentration of MI, and the matrix seems to be a prospective material for the PDLC devices.     

Preparation and electro‐optical properties of polymer dispersed liquid crystal films with relatively low liquid crystal content

In this paper, polymer dispersed liquid crystals (PDLC) films with LC content as low as 40 wt% were prepared, and the electro‐optical properties were carefully investigated. To accomplish this, different (meth)acrylate copolymerizaiton monomers have been used. The electro‐optical properties and morphologies of the PDLC films were strongly influenced by the chemical structure of copolymerization monomers (hydroxypropyl methacrylate (HPMA), glycidyl methacrylate, hydroxypropyl acrylate) and their feed ratio. Lower driven voltage and higher contrast ratio were achieved when the PDLC films showed a morphology with suitably LC domain size. At high HPMA content, a thin polymer film was formed on the surface of PDLC samples, which is beneficial to decrease the total LC content in PDLC devices. Copyright © 2013 John Wiley & Sons, Ltd.     

Effect of crosslinking polymer networks on the molecular reorientation and electro‐optical performance of in‐plane switching vertically aligned liquid crystal devices

The effects of crosslinking polymer networks (PNs) on the molecular reorientation and electro‐optical properties of vertically aligned (VA) liquid crystal (LC) devices are investigated by applying an in‐plane switching (IPS) electric field. Through the polymerization process, crosslinking PNs are developed on the substrate surface, effectively increasing the anchoring energy and governing the LC molecular reorientation. With its stronger anchoring effect, the PNs cell shows good light transmittance and excellent vertical alignment quality, as compared to the pure LC cell. Furthermore, the alignment transformation and transmittance bounce resulting from the transient process of LC molecular reorientation are eliminated when the cell is operated at high voltages. The rising‐time (t_r) and falling‐time (t_f) responses of the PNs cell are significantly improved, and around 36% improvement in the optical switching response is obtained. In addition, the dynamic gray‐level t_r and t_f responses of the PNs cell are enhanced by around 55% and 42%, respectively, at a low driving voltage (～12 V). This developed VA‐IPS LC/PNs cell benefits not only the LC molecular alignment but also the electro‐optical performance. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 1123–1130     

Control of liquid crystal droplet configuration in polymer dispersed liquid crystal with macro-iniferter polystyrene

A polystyrene macro-iniferter was applied to control the alignment of liquid crystal molecules at the droplet wall of polymer dispersed liquid crystal (PDLC) films. The aspects of the alignment were monitored by observing the droplet in the PDLC film. With increasing the macro-iniferter polystyrene in the composition, the configuration of LC droplets changes from bipolar to radial. This is because the high concentration of the macro-iniferter polystyrene results in a small surface interaction between the LC and the polymer matrix, which favours the formation of radial configuration. The radial configuration was stable under our conditions. However, increasing the LC and the initiator concentrations resulted in the change from radial to bipolar.     

The effect of the resultant microphase-separated structures of polymer matrices on the electro-optical properties of polymer dispersed liquid crystal films by Iniferter polymerization

Iniferter polymerization was employed to prepare polymer dispersed liquid crystal (PDLC) films and an additional photoinitiator was introduced to induce the phase separation of polymer matrices themselves on the process of preparing the PDLC. The effect of the polymerization kinetics and the resultant microphase-separated structures of polymer matrices on the electro-optical properties of PDLC films were studied. It was found that the bigger length scale of phase separation of polymer matrices induced strong light-scattering resulting in low ON-state transmittance. And faster polymerization kinetic induced higher threshold and saturation voltages.     

Reverse-mode polymer dispersed liquid crystal films prepared by patterned polymer walls

This article proposes a methodology to prepare polymer dispersed liquid crystal (PDLC) films working in the reverse-mode operation, where the ion-doped nematic liquid crystals (NLCs) with negative dielectric anisotropy (Δε) were locked by polymer walls. On-state and off-state of films were controlled by an electric field. In the absence of an electric field, it appears to be transparent. In the field, the homogeneous alignment NLCs form dynamic scattering, giving rise to opaque. The effect of the cylindrical holes with different diameters of photo masks and liquid crystal Δε on the electro-optical properties and transmittance wavelength range of 400–3000 nm light of samples were investigated. It was found that it exhibited very good electro-optical characteristics, high contrast ratio and excellent infrared energy-efficient of films used as switchable windows.     

Effects of crosslinking agent,cure temperature,and UV flux on the electro‐optical properties of polymer‐dispersed liquid crystal cells

We present results for the effects of a crosslinking agent, cure temperature, and UV flux on the electro‐optical properties of polymer‐dispersed liquid crystal (PDLC) cells. These cells were fabricated using a mixture of a liquid crystal (E8) and an acrylic monomer (CN135). The maximum in the first derivative of the transmission vs. applied, sinusoidal voltage (inflection voltage, V_inf), varies systematically with PDLC formulation and cure‐process conditions. For PDLC cells fabricated with a crosslinking agent (SR295), V_inf increases with increasing the concentration of SR295. However, for cells fabricated without the use of a crosslinking agent, V_inf decreases with increasing the UV flux and decreasing temperature. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 404–410, 2004     

Design,synthesis, and characterization of a combined main‐chain/side‐chain liquid crystalline polymer based on mesogen‐jacketed liquid crystal polymer via atom transfer radical polymerization

A novel combined main‐chain/side‐chain liquid crystalline polymer based on mesogen‐jacketed liquid crystal polymers (MJLCPs) containing two biphenyls per mesogenic core of MJLCPs main chain, poly(2,5‐bis{[6‐(4‐butoxy‐4′‐oxy‐biphenyl)hexyl]oxycarbonyl}styrene) (P1–P8) was successfully synthesized via atom transfer radical polymerization (ATRP). The chemical structure of the monomer was confirmed by elemental analysis, ¹H NMR, and ¹³C NMR. The molecular characterizations of the polymer with different molecular weights (P1–P8) were performed with ¹H NMR, gel permeation chromatography (GPC), and thermogravimetric analysis (TGA). Their phase transitions and liquid‐crystalline behaviors of the polymers were investigated by differential scanning calorimetry (DSC) and polarized optical microscope (POM). We found that the polymers P1–P8 exhibited similar behavior with three different liquid crystalline phases upon heating to or cooling in addition to isotropic state, which should be related to the complex liquid crystal property of the side‐chain and the main‐chain. Moreover, the transition temperatures of liquid crystalline phases of P1–P8 are found to be dependent on the molecular weight. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 7310–7320, 2008     

Photomechanical effects in liquid crystal polymer networks prepared with m‐fluoroazobenzene

The photomechanical response and photochemistry of a conventional, unsubstituted azobenzene‐functionalized liquid crystalline polymer network (azo‐LCN) is contrasted to that of an analogous material prepared with meta‐fluorinated azobenzene chromophores. The polydomain azo‐LCN materials exhibit nearly identical thermomechanical and optical properties. Photomechanical characterization indicates that the fluorination of the azobenzene chromophore reduces the deflection of cantilevers composed of the materials by 50%, which spectroscopic analysis reveals is due to a reduction in the ability of this material to isomerize and potentially reorient. This work is further confirmation that the underlying photochemistry of azobenzene is a primary contributor to the generation of photomechanical work in these materials. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 876–882     

Dye-dependent studies on droplet pattern and electro-optic behaviour of polymer dispersed liquid crystal

In order to study the droplet pattern and electro-optic (EO) behaviour of polymer dispersed liquid crystal (PDLC) with the addition of dye, dichroic polymer dispersed liquid crystal (DPDLC) films were prepared using a nematic liquid crystal (NLC), photo-curable polymer (NOA 65) and anthraquinone blue dichroic dye (B2), in equal ratio (1:1) of polymer and liquid crystal (LC) by polymerisation induced phase separation (PIPS) technique. Dichroic dye was taken in different concentration (wt./wt. ratio) as 0.0625%, 0.125%, 0.25%, 0.5% and 1% of the LC mixture in DPDLC films. Initially, in an open circuit when there is no proviso for external electric field (0 V), LC droplets in polymer matrix exhibited bipolar pattern, though on closing the circuit with the increase of electric field pattern of droplets starts changing, LC molecules align along the direction of applied electric field and aligned completely relatively at higher field (30 V), which illustrate vertical radial pattern. Further, results show that the DPDLC film containing 0.0625% dye concentration with consistent average droplet size ~4.30 μm, exhibits the best transmission at lower operating voltage.     

Effects of the fluorinated liquid crystal molecules on the electro-optical properties of polymer dispersed liquid crystal films

The different fluorinated liquid crystal (LC) molecules doped to E8 were used as LC component to prepare polymer dispersed liquid crystal (PDLC) films. The mass fraction of the LC mixture is fixed 50.0 wt%. Results indicate that doping 8.0 wt% fluorinated LC molecule ME3CP to E8 significantly reduced the driving voltage of the PDLC films, and the driving voltage reduced with the rise of mass fraction of ME3CP. Besides, the terminal flexible chain length of the fluorinated LC molecule influenced the LC mixture properties based on E8, such as the dielectric anisotropy, birefringence and viscosity of the LC mixture, and the morphology and the electro-optical properties of PDLC films were controlled not only by the physical properties of the LC mixture, but also by the terminal flexible chain length of the fluorinated LC molecule .     

Kinetically controlled phase transitions in liquid‐crystalline polymers. III. Influence of the molecular weight and annealing temperature on two‐dimensional K phase formation in a side‐chain polyacrylate

Narrow fractions of a side‐chain acrylate oligomer/polymer with phenyl benzoate side chains are separated in a broad range of the degree of polymerization (7 ≤ P_w ≤ 149). An examination of the phase behavior of the obtained fractions has shown that only the longer macromolecules can form the two‐dimensional K (TDK) mesophase, whereas oligomers of a shorter main chain form the conventional nematic phase only. A critical P_w value has been observed to be necessary for the TDK mesophase formation. The temperatures and enthalpies of liquid‐crystalline phase transitions have been studied as a function of the molar mass, and the phase‐growth kinetics for the TDK phase have been studied with an Avrami treatment. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 2352–2360, 2005     

固化条件对聚合物分散液晶膜电光性能的影响

选用聚乙二醇二缩水甘油醚(EGDE)/季戊四醇缩水甘油醚(PERTGE)/1,8-二氨基-3,6-二氧杂辛烷(EDBEA)/向列相液晶(SLC1717)复合体系,在不同的固化条件下,通过热聚合诱导相分离方法制备了一系列电光性能不同的聚合物分散液晶(polymer dispersed liquid crystal,简称PDLC)膜.研究了固化温度和固化时间对制备的PDLC膜中聚合物网络的微观形貌和电光性能的影响.结果表明,随着固化温度的升高以及固化时间的缩短,PDLC膜的对比度、驱动电压和开态响应时间逐渐增大,而关态响应时间逐渐减小.在固化温度为363.2 K,固化时间为7 h时,所制备的PDLC膜具有较佳的电光性能.     

A study on the polymer structures and electro-optical properties of epoxy-mercaptan-based polymer dispersed liquid crystal films

ABSTRACT

In this paper, polymer dispersed liquid crystal (PDLC) films based on epoxy-mercaptan system were prepared by thermal-initiated polymerization. The effects of the liquid crystal (LC) content, the proportion and the functionality of epoxy monomers on the polymer structures and electro-optical properties of the as-made PDLC films were investigated systematically. It was found that the morphologies of the polymer matrix can be altered from polymer meshes to polymer balls by increasing the LC content as well as the functionality of epoxy monomers. Accordingly, the electro-optical properties could be regulated by the morphologies of polymer networks. Especially, the as-made PDLC films with homogeneous porous structures exhibited the optimal electro-optical properties. Consequently, this work offers a meaningful approach to control the microstructures and optimize the electro-optical properties of PDLC films, which indeed can form a wonderful footstone for the wide application of PDLC.     

TSC study and electro‐optical properties of epoxy/acrylic polymer‐dispersed liquid‐crystal film in DICY thermal cure

We report on the structures and electro‐optical properties of epoxy/acrylic polymer‐dispersed liquid‐crystal (PDLC) films. A thermal stimulated current (TSC) analysis was used to investigate the physical structures of PDLC. In the TSC spectrum of PDLC, three relaxation peaks were observed: the glass transition of the liquid crystal, the glass transition of the polymer matrix, and the ρ transition. The ρ transition represents the discharge behavior of space charges, and its intensity increased as the curing time and content of the curing agent dicyandiamide (DICY) increased. The pre‐UV‐cured films with different DICY contents were thermally cured at 130 °C for various periods. The electro‐optical properties of PDLC, such as the contrast ratio and switching voltage, increased as the curing time of DICY, the content of DICY, or both increased. As the ambient temperature increased from 10 to 40 °C, the contrast ratio and switching voltage of PDLC gradually decreased. © 2001 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 39: 507–514, 2001     

Studies on electro‐optical properties of polymer matrix/LC/ITO nanoparticles composites

In this paper, polymer‐dispersed liquid crystal (PDLC) films consisting of liquid crystal (LC)/monomers/indium tin oxide (ITO) nanoparticles with good near‐infrared absorption property had been fabricated, and the influence of the ITO nanoparticles modified with 3‐methacryloxypropyltrimethoxysilane (KH570) on the PDLC films was systematically studied. First, different liquid crystal content was studied to obtain PDLC films with good electro‐optical properties. And then, various weight ratio of ITO nanoparticles was added to samples. While the content of ITO nanoparticles was increased, the saturation voltage increased and the CR decreased. Though the electro‐optical properties of PDLC samples reduced with the addition ITO nanoparticles, the near‐infrared absorption property of films was enhanced.     

Control of the microstructure of polymer network and effects of the microstructures on light scattering properties of UV‐cured polymer‐dispersed liquid crystal films

Polymer‐dispersed liquid crystals (PDLC) films were prepared from ultraviolet (UV) irradiation‐induced polymerization of the photopolymerizable monomers in photopolymerizable monomers/nematic liquid crystal (LC) mixtures. The effects of the composition of the mixtures, the curing temperature, and the UV light intensity on the microstructure of the polymer network in the PDLC films were investigated. Furthermore, the effects of the microstructures on the light scattering properties of the PDLC films in the wavelength region of 300–2500 nm were studied experimentally and theoretically based on the combination of three kinds of classical light scattering theories: the Rayleigh‐Gans (RG) approach, the anomalous diffraction (AD) approach, and the geometrical optics (GO) approach. It was found that the sizes of LC domain in PDLC films increased with the increase of the LC content as well as the decrease of the UV curing intensity, while increased at first and then decreased with the increase of the curing temperature. Moreover, smaller LC domain sizes could exhibit strong scattering properties in a smaller VIS wavelength region and the transmittance in NIR region (especially in the wavelength range of 1300–2500 nm) obviously decreased with the increasing sizes of LC domain. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 2090–2099, 2008     

Synthesis and properties of mesogen‐jacketed liquid crystalline polymers containing biphenyl mesogen with asymmetric substitutions

This work focuses on the design, synthesis, and characterization of a series of mesogen‐jacketed liquid crystalline polymers (MJLCPs), poly(alkyl 4′‐(octyloxy)‐2‐vinylbiphenyl‐4‐carboxylate) (pVBP(m,8), m = 1, 2, 4, 6, 8, 10, 12). For the first time, we realized asymmetric substitutions in the mesogens of MJLCPs. The polymers obtained by conventional free radical polymerization were investigated in detail by a combination of various techniques, such as differential scanning calorimetry, wide‐angle X‐ray diffraction, and polarized light microscopy. Our results showed that all the polymers were thermally stable, and their glass transition temperatures decreased when m increased. The liquid crystalline (LC) phases that developed at high temperatures and disappeared at low temperatures were strongly dependent on the difference in lengths of alkyl groups on the 4 and 4′ substitution positions of the side‐chain biphenyl. While polymer pVBP(1,8) was not liquid crystalline, columnar liquid crystalline phases were observed for all other pVBP(m,8) (m = 2, 4, 6, 8, 10, 12) polymers. Polymer pVBP(8,8) showed a tetragonal columnar nematic liquid crystalline phase, and the other LC polymers exhibited columnar nematic phases. In additions, the smaller the difference in the lengths of the terminal alkyls, the easier the development of the liquid crystalline phase. Birefringence measurements showed that solution‐cast polymer films exhibited moderately high positive birefringence values, indicating potential applications as optical compensation films for liquid crystal displays. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Synthesis and hierarchical superstructures of side‐chain liquid crystal polyacetylenes containing galactopyranoside end‐groups

Three kinds of chiral saccharide‐containing liquid crystalline (LC) acetylenic monomers were prepared by click reaction between 2‐azidoethyl‐2,3,4,6‐tetraacetyl‐β‐D ‐galactopyranoside and 1‐biphenylacetylene 4‐alkynyloxybenzoate. The obtained monomers were polymerized by WCl₆‐Ph₄Sn to form three side‐chain LC polyacetylenes containing 1‐[2‐(2,3,4,6‐tetraacetyl‐β‐D ‐galactopyranos‐1‐yl)‐ethyl]‐1H‐[1,2,3]‐triazol‐4′‐biphenyl 4‐alkynyloxybenzoate side groups. All monomers and polymers show a chiral smectic A phase. Self‐assembled hiearchical superstructures of the chiral saccharide‐containing LCs and LCPs in solution state were studied by field‐emission scanning electron microscopy. Because of the LC behavior, the LC molecules exhibit a high segregation strength for phase separation in dilute solution (THF/H₂O = 1:9 v/v). The self‐assembled morphology of LC monomers was dependent upon the alkynyloxy chain length. Increasing the alkynyloxy chain length caused the self‐assembled morphology to change from a platelet‐like texture ( LC‐6 ) to helical twists morphology ( LC‐11 and LC‐12 ). Furthermore, the helical twist morphological structure can be aligned on the polyimide rubbed glass substrate to form two‐dimensional ordered helical patterns. In contrast to LC monomers, the LCP‐11 self‐assembled into much more complicate morphologies, including nanospheres and helical nanofibers. These nanofibers are evolved from the helical cables ornamented with entwining nanofibers upon natural evaporation of the solution in a mixture with a THF/methanol ratio of 3:7. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 6596–6611, 2009     

Electro-optical and dielectric study of multi-walled carbon nanotube doped polymer dispersed liquid crystal films

The self-organising property of nematic liquid crystals (LCs) was used to align multi-walled carbon nanotubes (MWCNT) dispersed in them. MWCNT not only well integrate in the matrix but also, even at very low concentration, have a detectable effect on the LC properties that can be very attractive for display applications. In the present work, MWCNT were doped (0–0.5% wt/wt) in two different types of LCs. These MWCNT doped polymer dispersed LC (CPDLC) films were studied comprehensively using fundamental techniques. Polarising optical microscope (POM) and scanning electron microscope (SEM) techniques used for morphological study reveal that the LC droplet size remains unchanged with increase in MWCNT concentration. The electro-optical (EO) study performed by increasing voltage in steps of 10 V up to 100 V at an optimised frequency of 200 Hz and at temperature 25°C shows that the low MWCNT concentration films show good optical response than the higher one. The dielectric behaviour of CPDLC films in the frequency range 20 Hz to 20 MHz was investigated using precision impedance analyser. The obtained data were modelled with Debye and Cole-Cole methods to calculate relaxation time and distribution parameter (α). The zero value of α indicates Debye type relaxation processes.