A Self‐Sampling‐and‐Flow Biosensor for Continuous Monitoring

A self‐sampling‐and‐flow biosensor was fabricated by sandwiching a nitrocellulose strip on the working electrode side of the double‐sided microporous gold electrodes and a wicking pad on the counter electrode side. The double‐sided microporous electrodes were formed by plasma sputtering of gold on a porous nylon substrate. Sample was taken up to the enzyme‐immobilized working electrode by the capillary action of the front nitrocellulose strip dipped into the sample solution, analyzed electrochemically at the enzyme‐immobilized electrode, and diffuses out to the backside wicking pad through the micropores of the electrodes, constituting a complete flow cell device with no mechanical liquid‐transporting device. Biosensor was formed by co‐immobilizing the glucose oxidase and electron transfer mediator (ferrocene acetic acid) on the thioctic acid self‐assembled monolayer‐modified working electrode. A typical response time of the biosensor was about 5 min with the sensitivity of 2.98 nA/mM glucose, providing linear response up to 22.5 mM. To demonstrate the use of self‐sampling‐and‐flow biosensor, the consumption rate of glucose in the presence of yeast was monitored for five days.     

Which Parameters Affect the Response of the Channel Biosensor?

The important parameters in defining the response of the portable channel biosensor described previously are explored by connecting the portable flow cell to a gravity feed flow system and using a highly defined enzyme immobilization protocol which ensures the enzyme reaction is a surface reaction. The enzyme glucose oxidase (GOD) was immobilized by covalent attachment to a self‐assembled monolayer modified gold surface. As a glucose solution flowed down the rectangular duct defined by the flow cell, it passed over the enzyme layer where the enzyme reaction produced hydrogen peroxide. The hydrogen peroxide was swept further downstream to the detector electrode. The response of such an enzyme electrode was shown to be limited by mass transport of the cosubstrate oxygen to the enzyme layer. Increasing the amount of oxygen in the sample meant the response of the biosensor became limited by the enzyme kinetics. The influence of parameters such as flow rate, height of the channel, enzyme layer length and the gap between the enzyme layer and the detector electrode were explored.     

Minimization of Interferences in Flow Injection Amperometric Glucose Biosensor Based on Oxidation of Enzymatically‐produced H2O2

One of the major problems in amperometric biosensors based on detection of H₂O₂ produced by enzymatic reaction between oxidase enzymes and substrate is the interference of redox active compounds such as ascorbic acid (AA), dopamine (DA) and uric acid (UA). To minimize these interferences, sodium bismuthate was used for the first time as an insoluble pre‐oxidant in the flow injection (FI) amperometric glucose biosensor at a Glucose oxidase (GOx) immobilized Pt/Pd bimetallic modified pre‐anodized pencil graphite electrode (p.PGE). In this context, these interfering compounds were injected into a flow injection analysis (FIA) system using an injector which was filled with NaBiO₃. Thus, these interferents were converted into their redox inactive oxidized forms before reaching the electrode in the flow cell. While glucose was not influenced by the pre‐oxidant in the injector, the huge oxidation peak currents of the interferents decreased significantly in the biosensor. FI amperometric current time curves showed that the AA, DA and UA were minimized by 96 %, 86 %, and 98 % respectively, in the presence of an equivalent concentration of interferences in a 1.0 mM glucose solution. The proposed FI amperometric glucose biosensor exhibits a wide linear range (0.01–10 mM, R²=0.9994) with a detection limit of 2.4×10^?3 mM. Glucose levels in the artificial serum and two real samples were successfully determined using the fabricated FI amperometric biosensor.     

A PVC/TTF‐TCNQ Composite Electrode for Use as a Detector in Flow Injection Analysis

A new polyvinyl chloride (PVC)/tetrathiafulvalene‐tetracyanoquinodimethane (TTF‐TCNQ) composite electrode was prepared and tested for electroanalytical performance. Different PVC/TTF‐TCNQ–graphite proportions were used in order to obtain the best possible detector for accommodation in a wall‐jet electrochemical cell of use in flow injection analysis. A PVC/TTF‐TCNQ w/w ratio of 1/10 provided the best results in terms of sensitivity, coefficients of variation and mechanical resistance. The voltammetric and flow‐injection amperometric detection responses of the electrode to ascorbic acid (AA) were measured and compared with those of a PVC–graphite electrode. The resulting electrode provided good electrode kinetics with a low background current and a relatively reproducible signal. In addition, the electrode can be readily prepared and its surface readily renewed.     

Fabrication of Photoelectrochemical Glucose Biosensor in Flow Injection Analysis System Using ZnS/CdS‐Carbon Nanotube Nanocomposite Electrode

In this work, a photoamperometric glucose biosensor based on glucose oxidase (GODx) was developed in flow injection analysis (FIA) system using ZnS‐CdS quantum dot (QD) modified multiwalled carbon nanotube/glassy carbon electrode (ZnS‐CdS/MWCNT/GCE). Cyclic voltammograms of the proposed electrode (GODx/ZnS‐CdS/MWCNT/GCE) showed a pair of well‐defined reversible redox peak attributing that direct electron transfer between the protein and electrode. The current of the reduction peak became more cathodic in the presence of O₂ due to the electrocatalytic activity of the electrode towards the reduction of dissolved O₂, but reduction current shifted to a less negative value upon addition of glucose in the solution. The obtained CV currents were affected by the irradiation of the electrode surface. Thus, the photoelectrochemical biosensing of glucose in the FIA system was studied by monitoring of the changes in the electrocatalyzed reduction peak current of dissolved O₂ at the proposed electrode dependent on glucose concentration. The proposed photoelectrochemical FIA method has a linear response to glucose ranging from of 0.01 to 1.0 mM with detection limit of 3.0 μM under optimized conditions. Photoelectrochemical biosensor was successfully fabricated in FIA system for selective, sensitive and repeatable detection of glucose and has been satisfactorily applied to determination of glucose in real sample.     

Flow Injection Analysis of Ascorbic Acid in Real Samples Using a Highly Stable Chemically Modified Screen‐Printed Electrode

A silica sol‐gel glass‐coated ferricyanide‐doped Tosflex‐modified screen‐printed electrode (designated as SG/FeCN‐Ts/SPE) was used for the mediated oxidation of ascorbic acid in neutral pH. The sol‐gel overlayer was found to stabilize the Fe(CN) ‐Tosflex system without any foul‐off and deterioration behavior through chemical interaction between the hydrophilic sites of Tosflex and oxy‐ and/or ‐hydroxy surface functional groups of silicate. The electrochemical mediation of ascorbic acid was found to follow the Michaelis‐Menten kinetic pathway. The SG/FeCN‐Ts/SPE was very stable for repetitive measurements by flow injection analysis at 0.3 V (vs. Ag/AgCl). A linear calibration plot was obtained for ascorbic acid determination up to 300 μM with sensitivity and detection limit (S/N=3) of 2.85 nA/μM and 46 nM, respectively. The system also showed tolerable interference to uric acid, urea and carbohydrates and was used for the determination of ascorbic acid in human urine, clinical tablet and apple juice.     

Amperometric Biosensor for Choline Based on Gold Screen‐Printed Electrode Modified with Electrochemically‐Deposited Silica Biocomposite

A mediator‐free choline biosensor was developed using the electrochemically assisted sol‐gel deposition on gold screen‐printed electrodes. The addition of 12 mM of cationic surfactant CTAB in silica sol allowed enhancing the stability of the sensor. The modified electrode demonstrated catalytic activity and stable amperometric response to choline for over 3 weeks of exploitation with the sensitivity of 6 µA mM^?1 and LOD of 6 µM. The interference of ascorbic acid was reduced by pretreating the analyzed solution with MnO₂ powder. The application of the sensor with the purpose of identifying choline in the baby milk demonstrated satisfactory metrological characteristics.     

Lifetime Improvement of Glucose Biosensor by Epoxy‐Enhanced PVC Membrane

A new approach using epoxy resin to enhance the durability and adhesion of a diffusion‐limiting membrane in amperometric biosensors is described. The polymer membrane was mainly composed of commercially available fast epoxy adhesive ATACS 5104, poly(vinyl chloride) (PVC) and plasticizers such as isopropyl myristate (IMP) and Aliquat 336 (AL). It can be readily deposited on various substrates by using coating and other thin film fabrication methods. The effect of epoxy resin in the membrane composition was investigated using a coil‐type glucose biosensor containing extra enzyme. The ideal membrane was found to include approximately 1/3 epoxy resin, 1/3 plasticizer and 1/3 PVC. Such a membrane was verified to be porous and permeable to small molecules like glucose and can tightly adhere to other beneath layers such as a Nafion membrane, which serves as the interference‐eliminating layer. These epoxy‐based glucose biosensors showed excellent electrochemical response properties including a long lifetime and can be used for microanalysis of solutions and biological fluids. With an additional PU outermost layer, the present glucose biosensors can potentially be used for in vivo measurements.     

Electrochemical Reduction of a Conjugated Cinnamic Acid Diazonium Salt as an Immobilization Matrix for Glucose Biosensor

Initial results on the synthesis of a new conjugated diazonium salt of trans‐4‐cinnamic acid diazonium fluoroborate, which is used for the chemical modification of the glassy carbon (GC) electrode with trans‐4‐cinnamic acid groups through electrochemical reduction, and direct covalent immobilization of glucose oxidase (GOD) on the cinnamic acid groups are presented. The chemically modified GC electrode exhibits a good selectivity relative to the bare GC electrode for the various possible interfering compounds in glucose analysis: namely ascorbic acid and 4‐acetamidophenol. Covalent immobilization of GOD on the chemically modified GC electrode produces a biosensor which responds to glucose concentration changes in the presence of a soluble redox mediator (ferrocenemethanol). The chemical modification of GC by cinnamic acid groups is potentially useful for the attachment of other enzymes and biochemical reagents.     

Preparation of GOD/Sol‐Gel Silica Film on Prussian Blue Modified Electrode for Glucose Biosensor Application

A novel amperometric glucose biosensor was fabricated by in situ incorporating glucose oxidase (GOD) within the sol‐gel silica film on a Prussian blue (PB) modified electrode. The method is simple and controllable, which combined the merits of in situ immobilizing biomolecules in sol‐gel silica film by electrochemical method and the synergic catalysis effects of PB and GOD molecules. Scanning electron microscopy (SEM) showed that the GOD/sol‐gel silica film was homogeneous with a large number of three‐dimensional nanopores, which not only enhanced mass transport, but also maintained the active configuration of the enzyme molecule and prevented the leakage of enzyme, therefore improved the stability and sensitivity of the biosensor. The fabricated biosensor showed fast response time (10 s), high sensitivity (26.6 mA cm^?2 M^?1), long‐term stability, good suppression of interference, and linear range of 0.01 mM–5.8 mM with a low detection limit of 0.94 μM for the detection of glucose. In addition, the biosensor was successfully applied to determine glucose in human serum samples.     

SE‐30 Graphite Composite Electrode: An Alternative for the Development of Electrochemical Biosensors

A new graphite composite electrode was constructed by mixing graphite powder with chromatography stationary phase, SE‐30, as the binder. The electrochemical behavior of the new electrode has been evaluated and compared with that of traditional carbon paste electrode (CPE). The proposed electrode provides a remarkable increase in the rate of electron transfer of biomolecules such as nicotinamide adenine dinucleotide (NADH), cysteine, ascorbic acid and catechol and shows a low surface fouling effects. The electrode shows highly promising results when used as an amperometic sensor for biocompounds such as NADH.     

A Mediator‐Free Bienzyme Amperometric Biosensor Based on Horseradish Peroxidase and Glucose Oxidase Immobilized on Carbon Nanotube Modified Electrode

Multiwalled carbon nanotube (CNT) modified glassy carbon electrode immobilized with horseradish peroxidase (HRP) in Nafion coating showed direct electron transfer between HRP enzyme and the CNT‐modified electrode. A mediator‐free bienzyme glucose biosensor based on horseradish peroxidase and glucose oxidase was constructed. The bienzyme biosensor exhibited a high sensitivity for glucose detection at zero applied potential.     

Automated SIA e‐Tongue Employing a Voltammetric Biosensor Array for the Simultaneous Determination of Glucose and Ascorbic Acid

An automated voltammetric electronic tongue has been designed employing a biosensor array formed by three different enzymatic Glucose Oxidase (GOD) electrodes and the Sequential Injection Analysis principle. The system is used for its automated training and operation devised for determining glucose and one of its classical interferents, ascorbic acid. The three enzymatic biosensors contain GOD and different metallic catalysts in order to decrease the working potential and to differentiate the response of primary species and interferents. Linear sweep voltammetry has been the chosen technique for data generation and artificial neural networks have been used as the modeling tool. Different learning algorithms have been tried in order to obtaining the best architecture for the neural network. Glucose has been determined in different fruit juice samples by employing this system, correcting the ascorbic acid contents.     

Selective Detection of Ascorbic Acid Using Octacyanomolybdate‐Doped‐Glutaraldehyde‐Cross‐Linked Poly‐L‐Lysine Film Modified Glassy Carbon Electrode

The present work describes oxidation of ascorbic acid (AA) at octacyanomolybdate‐doped‐glutaraldehyde‐cross‐linked poly‐L ‐lysine (PLL‐GA‐Mo(CN) film modified glassy carbon electrode in 0.1 M H₂SO₄. The modified electrode has been successfully prepared by means of electrostatically trapping Mo(CN) mediator in the cationic film of glutaraldehyde‐cross‐linked poly‐L ‐lysine. The dependence of peak current of modified electrode in pure supporting indicates that the charge transfer in the film was a mixed process at low scan rates (5 to 200 mV s^?1), and kinetically restrained at higher scan rates (200 to 1000 mV s^?1). Cyclic voltammetry and rotating disk electrode (RDE) techniques are used to investigate the electrocatalytic oxidation of ascorbic acid and compared with its oxidation at bare and undoped PLL‐GA film coated electrodes. The rate constant of catalytic reaction k obtained from RDE analysis was found to be 9.5×10⁵ cm³ mol^?1 s^?1. The analytical determination of ascorbic acid has been carried out using RDE technique over the physiological interest of ascorbic acid concentrations with a sensitivity of 75 μA mM^?1. Amperometric estimation of AA in stirred solution shows a sensitivity of 15 μA mM^?1 over the linear concentration range between 50 and 1200 μM. Interestingly, PLL‐GA‐Mo(CN) modified electrode facilitated the oxidation of ascorbic acid but not responded to other electroactive biomolecules such as dopamine, uric acid, NADH, glucose. This unique feature of PLL‐GA‐Mo(CN) modified electrode allowed for the development of a highly selective method for the determination of ascorbic acid in the presence of interferents.     

Simultaneous Voltammetric Determination of Uric Acid and Ascorbic Acid Using a Carbon‐Paste Electrode Modified with Multi‐Walled Carbon Nanotubes/Nafion and Cobalt(II)nitrosalophen

A composition of multiwalled carbon nanotube (MWCNT), Nafion and cobalt(II)‐5‐nitrosalophen (CoNSal) is applied for the modification of carbon‐paste electrode (CPE). The pretreated MWCNT is well dispersed in the alcoholic solution of Nafion under the ultrasonic agitation, and the resulted suspension is used as modifier (with 10% w/w) in the matrix of the paste electrode. The prepared electrode further modified by addition of 3 wt% of CoNSal. The resulted modified electrode is used as a sensitive voltammetric sensor for simultaneous determination of uric acid (UA) and ascorbic acid (AA). The electrode showed efficient electrocatalytic activity in lowering the anodic overpotentials and enhancement of the anodic currents. This electrode is able to completely resolve the voltammetric response of UA and AA. The effects of potential sweep rate and pH of the buffer solution on the response of the electrode, toward UA and AA, and the peak resolution is thoroughly investigated by cyclic and differential pulse voltammetry (CV and DPV). The best peak resolution for these compounds using the modified electrode is obtained in solutions with pH 4. The ΔE_p for UA and AA in these methods is about 315 mV, which is considerably better than previous reports for these compounds. A linear dynamic range of 1×10^?7 to 1×10^?4 M with a detection limit of 6×10^?8 M is resulted for UA in buffered solutions with pH 4.0. The voltammetric response characteristics for AA are obtained as, the linear range of 5×10^?7 to 1×10^?4 M with the detection limit of 1×10^?7 M. The voltammetric detection system was very stable and the reproducibility of the electrode response, based on the six measurements during one month, was less than 3.5% for the slope of the calibration curves of UA and AA. The prepared modified electrode is successfully applied for the determination of AA and UA in mixture samples and reasonable accuracies are resulted.     

Simultaneous Determination of Dopamine and Ascorbic Acid Using the Nano‐Gold Self‐Assembled Glassy Carbon Electrode

Electrochemical behavior of dopamine (DA) was investigated at the gold nanoparticles self‐assembled glassy carbon electrode (GNP/LC/GCE), which was fabricated by self‐assembling gold nanoparticles on the surface of L ‐cysteine (LC) modified glassy carbon electrode (GCE) via successive cyclic voltammetry (CV). A pair of well‐defined redox peaks of DA on the GNP/LC/GCE was obtained at E_pa=0.197 V and E_pc=0.146 V, respectively. And the peak separation between DA and AA is about 0.2 V, which is enough for simultaneous determination of DA and AA. The peak currents of DA and AA were proportional with their concentrations in the range of 6.0×10^?8–8.5×10^?5 mol L^?1 and 1.0×10^?6–2.5×10^?3 mol L^?1, with the detection limit of 2.0×10^?8 mol L^?1 and 3.0×10^?7 mol L^?1 (S/N=3), respectively. The modified electrode exhibits an excellent reproducibility, sensibility and stability for simultaneous determination of DA and AA in human serum with satisfactory result.     

A New Amperometric Biosensor Based on HRP/Nano-Au/L-Cysteine/Poly（o-Aminobenzoic acid）-Membrane-Modified Platinum Electrode for the Determination of Hydrogen Peroxide

The third generation amperometric biosensor for the determination of hydrogen peroxide （H2O2） has been described. For the fabrication of biosensor, o-aminobenzoic acid （oABA） was first electropolymerized on the surface of platinum （Pt） electrode as an electrostatic repulsion layer to reject interferences. Horseradish peroxidase （HRP） absorbed by nano-scaled particulate gold （nano-Au） was immobilized on the electrode modified with polymerized o-aminobenzoic acid （poABA） with L-cysteine as a linker to prepare a biosensor for the detection of H2O2. Amperometric detection of H2O2 was realized at a potential of ＋20 mV versus SCE. The resulting biosensor exhibited fast response, excellent reproducibility and sensibility, expanded linear range and low interferences. Temperature and pH dependence and stability of the sensor were investigated. The optimal sensor gave a linear response in the range of 2.99×10^-6 to 3.55×10^-3 mol·L^-1 to H2O2 with a sensibility of 0.0177 A·L^-1·mol^-1 and a detection limit （S/N = 3） of 4.3×10^-7 mol·L^-1. The biosensor demonstrated a 95% response within less than 10 s.     

Electrochemical Study on DNA Damage Based on the Direct Oxidation of 8‐Hydroxydeoxyguanosine at an Electrochemically Modified Glassy Carbon Electrode

The study of DNA damage induced by Fenton reaction (Fe²⁺/H₂O₂) in vitro was performed based on the direct electrochemical oxidation of 8‐hydroxydeoxyguanosine (8‐OH‐dG), the biomarker of DNA oxidative damage, at an electrochemically modified glassy carbon electrode (GCE). The effects of antioxidants, such as ascorbic acid, and hydroxyl‐radical scavenger (mannitol) on the DNA damage were also investigated. 8‐OH‐dG, the oxidation product of guanine residues in DNA, has shown significantly oxidative peak on the electrochemically modified GCE. The oxidative peak current of 8‐OH‐dG was linear with the damaged DNA concentration in the range of 10–200 mg/L. The experimental results demonstrate that ascorbic acid has ambivalent effect on DNA oxidative stress. It can promote DNA oxidative damage when ascorbic acid concentration is below 1.5 mM and protect DNA from damage in the range of 1.5–2.5 mM. As a hydroxyl‐radical scavenger, mannitol inhibits significantly DNA oxidative damage. The influence of Fe²⁺, as reactant, and EDTA as iron chelator in the system were also studied. The proposed electrochemical method can be used for the estimation of DNA oxidative damage from new point of view.     

Selective Electrochemical Determination of Uric Acid in the Presence of Ascorbic Acid Using a Carbon Paste Electrode Modified with β‐Cyclodextrin

Uric acid (UA) was determined in the presence of ascorbic acid (AA) by using a carbon paste electrode modified superficially by a β‐cyclodextrin film (CPE/β‐CD). The surface carbon paste electrode was prepared applying a 30 cycles potential program and using a 1 M HClO₄+0.01 M β‐CD electrolytic solution. The UA and AA solutions were used to evaluate the electrode selectivity and sensitivity by cyclic voltammetric and amperometric methods. In these experiments the detection limit for UA was (4.6±0.01)×10^?6 M and the RSD calculated from the amperometric curves was 10%. From the data obtained it was possible to quantify UA in the urine and saliva samples. Selective detection of UA was improved by formation of an inclusion complex between β‐CD and UA. The results show that the CPE/β‐CD is a good candidate due to its selectivity and sensitivity in the UA determination in complex samples like the biological fluids.     

Simultaneous Determination of Dopamine and Ascorbic Acid at an In‐Site Functionalized Self‐Assembled Monolayer on Gold Electrode

The in‐site functionalization of 4‐aminothiophenol (4‐ATP) self‐assembled monolayer on gold electrode at physiological pH yields a redox active monolayer of 4′‐mercapto‐N‐phenylquinone diimine (MNPD). The functionalized electrode exhibits excellent electrocatalytic responses towards dopamine (DA) and ascorbic acid (AA), reducing the overpotentials by about 0.22 V and 0.34 V, respectively, with greatly enhanced current responses. Due to its different catalytic activities toward DA and AA, the modified electrode resolves the overlapping voltammetric responses of DA and AA into two well‐defined voltammetric peaks by differential pulse voltammetry (DPV), which can be used for the simultaneous determination of these species in a mixture. The catalytic peak current obtained from DPV was linearly related to DA and AA concentration in the ranges of 5.0×10^?6?1.25×10^?4 M and 8.0×10^?6?1.3×10^?4 M with correlation coefficient of 0.999 and 0.998, respectively. The detective limits (3σ) for DA and AA were found to be 1.2×10^?6 M and 2.4×10^?6 M, respectively. The modified electrode shows good sensitivity, selectivity and stability, and has been applied to the determination of DA and AA simultaneously in samples with satisfactory results.