Flow Injection Determination of Hydrogen Peroxide Using a Carbon Paste Electrode Modified with a Manganese Dioxide Film

Abstract

A manganese dioxide film modified carbon paste electrode was developed for use as an amperometric sensor for the determination of hydrogen peroxide (H₂O₂) in ammoniacal aqueous solutions. The electrode showed a stable response towards H₂O₂ after electrochemical activation. Effects of flow rate, operating potential, concentration, injection volume and interferences were investigated. A linear response towards H₂O₂ from 5 μg.l^?1 to 450 mg.l^?1 and a detection limit (3 signal-to-noise ratio) of 4.7 μg.l^?1 was found. The method was employed for the determination of H₂O₂ in rain water samples.     

Application of a New pH‐Sensitive Electrode as a Detector in Flow Injection Potentiometry

A new pH sensitive detector for flow‐through potentiometry was developed on the basis of a graphite/quinhydrone composite electrode. The detector was constructed of two polymethylmethacrylate plates between which a 0.1 mm thick sensitive layer is situated. After drilling a hole through the plates, a ring of the sensitive layer is exposed to the solution stream. A conventional calomel reference electrode was placed downstream following the flow‐through sensor. The response behavior in different electrolyte solutions was investigated. The detector shows a Nernstian behavior for injections of hydrochloric acid into a KCl background solution as well as for the steady state response in concentration step experiments using hydrochloric acid and buffer solutions. The response time is sufficiently short for FIA applications (T₉₅ between 3 and 5.4 s). The influences of flow rate and injection volume on the detector signal are discussed.     

Flow Injection Analysis of Maleic Hydrazide Using an Electrochemical Sensor Based on Palladium‐Dispersed Carbon Paste Electrode

A new analytical methodology for the electrochemical detection of the herbicide maleic hydrazide (3,6‐dihydroxypyridazine) by flow injection analysis is presented. This method is supported by the novel application of a palladium‐dispersed carbon paste electrode as an amperometric sensor for this herbicide. Maleic hydrazide shows anodic electrochemical activity on carbon‐based electrodes (glassy carbon or carbon paste electrodes) in all the pH range. This electrochemical activity is enhanced using metal‐dispersed carbon paste electrodes, especially at Pd‐dispersed CPE which displays good oxidation signals at 690 mV (0.050 M phosphate buffer pH 7.0), 140 mV lower than at unmodified electrodes. Under the optimized conditions, the electroanalytical performance of Pd‐dispersed CPE in flow injection analysis was excellent, with good reproducibility (RSD 3.3%) and a wide linear range (1.9×10^?7 to 1.0×10^?4 mol L^?1). A detection limit of 1.4×10^?8 mol L^?1 (0.14 ng maleic hydrazide) was obtained for a sample loop of 100 μL at a fixed potential of 700 mV in 0.050 M phosphate buffer solution at pH 7.0 and a flow rate of 2.0 mL min^?1. The proposed method was applied for the maleic hydrazide detection in natural drinking water samples.     

Self‐Assembled Mercapto‐Compound‐Gold‐Nanoparticle‐Modified Carbon Paste Electrode for Potentiometric Determination of Cadmium(II)

A new modified carbon paste electrode (CPE) based on a recently synthesized ligand [2‐mercapto‐5‐(3‐nitrophenyl)‐1,3,4‐thiadiazole] (MNT), self‐assembled to gold nanoparticles (GNP) as suitable carrier for Cd(II) ion with potentiometric method are described. The proposed electrode exhibits a Nernstian slope of 29.4±1.0 mV per decade for Cd(II) ion over a wide concentration range from 3.1×10^?8 to 3.1×10^?4 mol L^?1. The detection limit of electrode was 2.0×10^?8 mol L^?1 of cadmium ion. The potentiometric responses of electrode based on MNT is independent of the pH of test solution in the pH range 2.0–4.0. It has quick response with response time of about 6 s. The proposed electrode show fairly good selectivity over some alkali, alkaline earth, transition and heavy metal ions. Finally, the proposed electrode was successfully employed to detect Cd(II) ion in hair and water samples.     

Potentiometric Determination of Sibutramine Using Batch and Flow Injection Analysis

Sibutramine (SBT⁺) ion-selective electrode (ISE) was constructed using poly(vinyl chloride) matrix membrane containing sibutramine–phosphotungstate (SBT–PTA) plasticized with dioctyl phthalate. The electrode exhibits Nernstian response of 59.54 mV/ concentration decade over the concentration range 1.0 × 10^?5 to 1.0 × 10^?2 M and detection limit of 7.94 × 10^?6 M. The electrode was fully characterized in terms of its composition, response time, life span, pH, selectivity, and temperature and was then applied to the potentiometric determination of SBT in its pure bulk and pharmaceutical formulations under batch and flow injection conditions and for the in vitro testing of the dissolution profile of SBT capsules.     

氧化钯作为电位型传感器中敏感电极的工作机理

This paper describes the sensing properties of a potentiometric sensor based on a palladium oxide (PdO) electrode. Our investigation of the sensing mechanism is also discussed. We studied carbon monoxide (CO) sensing performance of a PdO electrode doped with Mg, Ni, and La, printed on zirconia. The results indicated that defects on the surface of PdO, which allow adsorption of CO, can effectively enhance the sensitivity of the sensors. To explore the source of the signal, a PdO-based electrode was printed on an alumina disc and a zeolite pellet for CO detection at 450℃. Notably the zeolite coupled with the PdO-based electrode to generate potentiometric responses to changes in CO concentration. According to the resistance and impedance measurements, the response to CO was ascribed to the changing interfacial potential between the PdO electrode and electrolyte. A model based on an electrochemical double layer between the PdO and electrolyte was determined to explain the behavior of the potentiometric sensor. It may be possible to harness these effects at PdO electrodes for the development of electrochemical sensors.     

A PVC/TTF‐TCNQ Composite Electrode for Use as a Detector in Flow Injection Analysis

A new polyvinyl chloride (PVC)/tetrathiafulvalene‐tetracyanoquinodimethane (TTF‐TCNQ) composite electrode was prepared and tested for electroanalytical performance. Different PVC/TTF‐TCNQ–graphite proportions were used in order to obtain the best possible detector for accommodation in a wall‐jet electrochemical cell of use in flow injection analysis. A PVC/TTF‐TCNQ w/w ratio of 1/10 provided the best results in terms of sensitivity, coefficients of variation and mechanical resistance. The voltammetric and flow‐injection amperometric detection responses of the electrode to ascorbic acid (AA) were measured and compared with those of a PVC–graphite electrode. The resulting electrode provided good electrode kinetics with a low background current and a relatively reproducible signal. In addition, the electrode can be readily prepared and its surface readily renewed.     

Flow Injection Analysis of Chloramphenicol by Using a Disposable Wall‐Jet Ring Disk Carbon Electrode

A preanodized screen‐printed ring disk carbon electrode was applied to the determination of chloramphenicol (Ph? NO₂, CAP) by flow injection analysis (FIA). By setting up the first irreversible reduction reaction of Ph? NO₂ to Ph? NHOH at the disk electrode, the following reversible oxidation of hydroxylamine (Ph? NHOH) to the nitroso (Ph? NO) derivative can be monitored/collected at the ring electrode for CAP analysis. The interference from dissolved oxygen and others can thus be avoided by using this approach and precise CAP determination can be easily performed by FIA under aerobic conditions. Preanodization treatment helps to lower the overpotential of the electrochemical reaction of CAP and favors the selective detection in aqueous medium. Under the optimum conditions, ten repetitive determinations at 1 μM and 10 μM CAP resulted in relative standard deviations of less than 4%, indicating good reproducibility of the system. A linear calibration range of 0.1–20 μM with a detection limit of 0.074 μM (S/N=3) was obtained. Veterinary pharmaceutics were finally analyzed by this sensor to validate its practical applicability.     

New Determination Scheme of p‐Aminophenol by MnO2 Modified Electrode Coupled with Flow Injection Analysis

New determination scheme of p‐aminophenol by using MnO₂ as a preoxidant is demonstrated in this work. In the flow injection system, the p‐aminophenol is oxidized to quinoneimine by MnO₂ at up‐stream, which can be detected at a suitable reductive potential. After optimization, the linear range of PAP is started from 1 μM to 30 μM (R²=0.999), the estimated detection limit (S/N=3) is 0.28 μM. Two real samples are studied and excellent recoveries are achieved by using standard addition method.     

A Novel Potentiometric Sensor for Thiocyanate Based on an Amide‐Linked Manganese Diporphyrin Xanthene

The synthesis of a new compound, amide‐linked manganese diporphyrin xanthene (Mn₂Cl₂ADPX), and its application for preparation of thiocyanate selective electrodes was described. The electrode was prepared with a PVC membrane combining Mn₂Cl₂ADPX as an electro active material, 2‐nitrophenyl octyl ether (o‐NPOE) as a plasticizer in the percentage ratio of 3 : 65 : 32 (Mn₂Cl₂ADPX: o‐NPOE: PVC, w : w : w). The electrode exhibited linear response within the concentration range of 2.4×10^?6 to 1.0×10^?1 M SCN^?, with a working pH range from 3.0 to 8.0 and a fast response time of less than 60 s. Several electroactive materials and solvent mediators have been compared and the experimental conditions were optimized. The Mn₂Cl₂ADPX based electrode shows obviously better response characteristics than that of monoporphyrin manganese in terms of working concentration range and slope. Selectivity coefficients for SCN^? relative to a number of interfering ions were investigated. The electrode exhibits anti‐Hofmeister selectivity toward SCN^? with respect to common coexisting anions. The electrode was applied to the determination of SCN^? in body urine with satisfactory results.     

流动注射掺杂普鲁士蓝碳糊电极测定过氧化氢

在化学法制得普鲁士蓝(PB)粉末的基础上,用固体石蜡作粘合剂,将PB粉末和石墨粉按一定比例充分混合,制得掺杂PB的碳糊电极(PBCPE)。研究了该修饰电极的制备,电化学性质及对H2O2的电催化作用。该修饰电极在0.5mol/L的KCl底液中进行循环伏安实验,于0.2V(vs.SCE)附近出现一对氧化还原峰,扫速为30mV/s时,峰电位差67mV,重现性良好。采用流动注射进样,基于PBCPE电极成功实现了恒电位快速检测医用消毒水中H2O2的浓度。最佳检测电位为-0.3V,进样频率为120次/小时。响应电流与H2O2的浓度在0.08～3.2mmol/L范围内呈良好的线性关系,线性相关系数为0.9994,检出限为2.4×10-6mol/L(S/N=3)。     

Flow Injection Analysis of Ascorbyl Glucoside in Cosmetics by a Disposable Printed‐Circuit Board Waste Modified Electrode

Ascorbyl glucoside, i.e., ascorbic acid 2‐glucoside (AA‐2G), is anew type of stable vitamin C derived compound used in many cosmetic skin‐lightening formulations, but rarely studied in the literature. In this study, a screen printed electrode modified with copper‐enriched printed circuit‐board waste (designated as Cu_PCB/SPE) was applied to study the electrochemical characteristics of AA‐2G. Cyclic voltammogram of the Cu_PCB/SPE showed an electrocatalytic oxidative feature at ?0.6 V vs. Ag/AgCl in 0.15 M NaOH solution. Flow injection analysis coupled with the Cu_PCB/SPE was further developed for sensitive AA‐2G determination. The calibration plot was linear in the window of 2.5–160 ppm with slope and regression coefficient of 0.0169 μA/ppm and 0.9971, respectively. The detection limit (S/N = 3) was 0.247 ppm. Real sample analysis was demonstrated for different skin‐lightening cosmetic products with appreciable results.     

Carbon Paste Electrode Modified with Functionalized Nanoporous Silica Gel as a New Sensor for Determination of Silver Ion

A new dipyridyl‐functionalized silica gel (DPSG) was synthesized. The potentiometric response of silver ion was investigated at a carbon paste electrode chemically modified with functionalized nanoporous silica gel. The electrodes with a DPSG proportions of 10.1% (w/w), showed very stable potential. Calibration plots with Nernstian slopes for Ag⁺ were observed, 58.7 (±0.9) mV decade^?1, over a wide linear range of concentration (5.0×10^?7 to 1.0×10^?1 M). The electrode has a detection limit of 1.0×10^?7 M. The selectivity coefficients measured by the match potential method in acetate buffer, pH 5.5, were investigated. The electrode has fast response time, high performance, high sensitivity in wide cation activity ranges, and good long term stability (more than 6 months). The method was satisfactory and used to determine the concentration of silver ion in waste waters contaminated by this metal.     

Potentiometric Response of Modified Carbon Paste Electrode Based on Mixed Ion‐Exchangers

A new chemically modified carbon paste electrode based on a mixture of two ion‐exchangers namely chlorpheniramine‐silicotungstate (CPM‐ST) and chlorpheniramine‐tetraphenylborate (CPM‐TPB) as ion‐exchange site for determination of chlorpheniramine maleate (CPM) was described. The best performance was exhibited by the electrode having the paste containing 3.0 wt% ion‐exchangers (CPM‐ST&CPM‐TPB), 48.5 wt% graphite, 47.5 wt% DOPh and 1.0 wt% NaTPB. The proposed chemically modified carbon paste electrode exhibited a Nernstian response for CPM over a wide concentration range of 1.2×10^?6 to 1.0×10^?2 M with a detection limit of 5.1×10^?7 M between pH 4.5 and 7.7 with fast response ≤10 s. The sensor showed good selectivity for CPM with respect to a large number of inorganic cations, organic cations, sugars, amino acids and some common drug excipients. The modified electrode was applied to potentiometric determination of CPM in its pharmaceutical preparations and biological fluids (serum and urine) with average recoveries of 97.5–102% and relative standard deviations of 0.32–1.97%.     

Flow Injection Analysis of Iodate Reduction on PEDOT Modified Electrode

Poly‐(3,4‐ethylenedioxythiophene) (PEDOT) films were electrodeposited by cyclic voltammetry on glassy carbon electrode at different anodic potentials in the range of 1.0–1.5 V (Ag/AgCl) and its electrocatalytic properties towards reduction of iodate were reported. The effect of the pH of the solution on the response of PEDOT electrode towards iodate also studied. The modified electrode was employed successfully as an amperometric sensor for iodate in a flow injection apparatus. The repeatability of the method for 14 injections of a μM iodate solution was 7%. Interference from other oxidant anions such as nitrate was not noticeable, whereas bromate, chlorate and nitrite interfere at slight levels.     

Flow Injection Analysis of Aluminum Chlorohydrate in Antiperspirant Deodorants Using a Built‐in Three‐in‐one Screen‐Printed Silver Electrode

A screen‐printed silver strip with a built‐in three‐in‐one electrode (SPAgE) configuration of Ag‐working, Ag‐counter and Ag/Ag_xO (silver oxides) pseudoreference electrodes has been developed for sensitive and selective electrochemical flow injection analysis (FIA) of aluminum chlorohydrate (ACH) present in antiperspirants, through the free Cl^? ion liberated from ACH in aqueous medium, as a redox signal at Ag‐working electrode in pH 6 phosphate buffer solution (PBS). The solution phase and instrumental parameters were systematically optimized. The calibration graph was linear in the window 1–200 ppm concentration of ACH and the lowest detection limit (S/N=3) was 295 ppb with a slope of 0.0989 μA/ppm and regression coefficient of 0.998. Calculated relative standard deviation (RSD) values for the detection of 5 and 50 ppm ACH by this method are 2.21 % and 2.16 %, respectively. Four different antiperspirant deodorants real samples with and without ACH content were successfully analyzed and the detected values obtained were found to be in good agreement with the product labeled values.     

Fabrication of an Electrochemical L‐Cysteine Sensor Based on Graphene Nanosheets Decorated Manganese Oxide Nanocomposite Modified Glassy Carbon Electrode

The graphene nanosheets/manganese oxide nanoparticles modified glassy carbon electrode (GC/GNSs/MnOx) was simply prepared by casting a thin film of GNSs on the GC electrode surface, followed by performing electrodeposition of MnOx at applied constant potential. The GC/GNSs/MnOx modified electrode shows high catalytic activity toward oxidation of L ‐cysteine. Hydrodynamic amperometry determination of L ‐cysteine gave linear responses over a concentration range up to 120 µM with a detection limit of 75 nM and sensitivity of 27 nA µM^?1. The GC/GNSs/MnOx electrode appears to be a highly efficient platform for the development of sensitive, stable and reproducible L ‐cysteine electrochemical sensors.     

A Novel Flow‐Through Planar Solid Contact Sensor for the Determination of Lead with Potentiometric Anionic Response

The construction and general performance characteristics of two poly(vinyl chloride) matrix chemical sensors for lead were described. These sensors were based on the use of ion association complexes of trihydroxoplumbate, [Pb(OH)₃]^? and tetraiodoplumbate, [PbI₄]^2?with cetylpyridinium chloride (CP) and iron(II)‐4,7‐bathophenanthroline [Fe(bphen)₃]²⁺ as novel electroactive materials dispersed in o‐nitrophenyloctyl ether (o‐NPOE) plasticizer for ionometric sensor controls, respectively. The sensing membrane (3×5 mm) is immobilized on a wafer polyimide chip (size 13.5×3.5 mm) to offer a planar miniaturized design that could be easily used flow injection system. Under static modes of operation, the sensors revealed a near Nernstian response over a wide Pb²⁺ ion concentration range 7.9×10^?7 to 10^?4 and 3.2×10^?7 to 10^?4 mol L^?1 with detection limit of 100 and 45.5 ng mL^?1, respectively . In flow injection potentiometry, excellent reproducibility (RSD%=0.5%), fast response, high sensitivity, high sampling rate (50 sample h^?1) and stable baseline was observed in the presence of 5×10^?2 mol L^?1 NaOH and 10^?1 mol L^?1 KI as a carrier for [CP][Pb(OH)₃] and [Fe(bphen)₃][PbI₄] membrane based sensors, respectively. Validation of the assay method according to the quality assurance standards (range, within‐day repeatability, between‐day variability, standard deviation, accuracy, lower detection limit) reveals good performance characteristics and suggests application for routine determination of lead in industrial wastewaters and stack emissions of lead smelters. The results agree fairly well with data obtained by the standard atomic absorption methods.     

Nanostructured Modified Carbon Paste Electrode as Voltrammetric Sensor for Isoproturon Trace Analysis in Water

A new electrochemical sensor based on nanostructured carbon paste electrodes (CPEs) is developed for the sensitive detection of Isoproturon in water. The CPEs were nanostructured by incorporation of carbon nanotubes (NTCs) and synthetized copper oxide nanoparticles (CuO). They were characterized using the X‐ray diffraction spectroscopy (XRD), scanning electron microscopy (SEM) and voltammetric methods. Electrochemical experiments showed that the adsorption of Isoproturon on to (GC‐NTC‐CuO)‐CPE, associated with nanomaterials (NTCs and CuO), provided remarkable analytical performances of the sensor such as a large quantification range from 1 to 200 μg L^?1 with a detection limit of 0.1 μg L^?1 of Isoproturon and no interferences of some another pesticides tested (specificity of ISO adsorption in acidified water). The tests carried out on real samples of water are conclusive. The analytical performances of the sensor showed that it is suitable for the specific determination of pesticide traces in water.