A Bipotentiostat Based 4‐Electrode Detection System for HPLC Analysis

With the assist of a microcomputer interfacing, a bipotentiostat in corporated 4‐electrode detection system was developed as a versatile electrochemical detector for HPLC. An amperometric chromatogram and two three‐dimensional chromatovoltammograms characterizing the electrochemical characteristics of analytes can be obtained in a single chromatographic run. By following the three operation modes developed, both the oxidizable and reducible analytes contained in sample solutions can be determined. The analytical capability of the 4‐electrode detection system was demonstrated by the analysis of solutions containing hydroquinone, catechol and ascorbic acid. From the calibration graphs obtained, linear coefficients better than 0.9992 were found for hydroquinone and catechol in a concentration range of 1.0 × 10^?4 to 1.0 × 10^?7 M, and a linear coefficient of 0.9929 was found for ascorbic acid in a concentration range of 1.0 × 10^?4 to 1.0 × 10^?6 M. The detection limits (based on S/N = 3) found were about 1.0 × 10^?7 M for hydroquinone and catechol and was 1.0 × 10^?6 M for ascorbic acid.     

Studies on the Interaction of Some Biologically Significant Radical Scavengers on Metal‐Ion Catalyzed Phloroglucinol‐Based Chemical Oscillator

The response of the Ce(III)‐catalyzed phloroglucinol (1,3,5‐trihydroxybenzene)‐based Belousov Zhabotinsky system to the addition of various antioxidants (ascorbic acid, glutathione, inosine, N‐acetylcysteine) is monitored at 30°C under stirred batch conditions. This method is convenient and has good sensitivity for the determination of these antioxidants. The addition of these antioxidants to the BZ mixture influences the oscillatory parameter (number of oscillations) to an extent that depends on the concentration of the antioxidant. The experimental results have shown that the number of oscillations decrease on increasing the concentration of antioxidant. The calibration plots show a linear relationship (R² = 0.98 for ascorbic acid and glutathione and R² = 0.99 for inosine and N‐acetylcysteine) between the number of oscillations and the [antioxidant] over the concentration range of 0.0125‐0.5, 0.05‐0.2, 0.025‐0.1, and 0.1‐0.5 mol L^?1 with detection limits 6.9 × 10^?5, 2.762 × 10^?4, 1.381 × 10^?4, and 5.524 × 10^?4 mol L^?1 for ascorbic acid, glutathione, inosine, and N‐acetylcysteine, respectively. Some aspects of the mechanism of these antioxidants on the BZ system have been discussed.     

Quantitative Analysis of Prometrine Herbicide by Liquid–Liquid Extraction Procedures Coupled to Electrochemical Measurements

A sensitive method is proposed for the preconcentration and quantification of the herbicide Prometrine (PROM) at a liquid‐liquid interface employing square‐wave voltammetry. The preconcentration stage was based on liquid‐liquid extraction methodology and the PROM quantification was carried out from the peak current of square‐wave voltammograms. Under the experimental conditions employed, linear calibration curves in the concentration range 1.0×10^?6 M–5.0×10^?5 M, with detection limit equal to 1.5×10^?6 M were obtained without pretreatment of the samples. This linear range, as well as detection limit could be extended towards lower concentrations when a pretreatment procedure was employed. In this way, linearity of calibration curves between 8.0×10^?8 M and 2.4×10^?7 M and detection limit of 1.0×10^?7 M, were observed. On the other hand, the standard addition method was also used as an alternative and an appropriated quantification technique for this system. A linear concentration range between 1.0×10^?6 M and 2.7×10^?5 M, with a correlation coefficient of 0.997, was obtained. This procedure has also a promising application in the separation of herbicides from other interferents, present in real samples, previous to their quantification.     

Low‐Background,Highly Sensitive DNA Biosensor by Using an Electrically Neutral Cobalt(II) Complex as the Redox Hybridization Indicator

An electrically neutral cobalt complex, [Co(GA)₂(phen)] (GA=glycollic acid, phen=1,10‐phenathroline), was synthesized and its interactions with double‐stranded DNA (dsDNA) were studied by using electrochemical methods on a glassy carbon electrode (GCE). We found that [Co(GA)₂(phen)] could intercalate into the DNA duplex through the planar phen ligand with a high binding constant of 6.2(±0.2)×10⁵ M ^?1. Surface studies showed that the cobalt complex could electrochemically accumulate within the modified dsDNA layer, rather than within the single‐stranded DNA (ssDNA) layer. Based on this feature, the complex was applied as a redox‐active hybridization indicator to detect 18‐base oligonucleotides from the CaMV35S promoter gene. This biosensor presented a very low background signal during hybridization detection and could realize the detection over a wide kinetic range from 1.0×10^?14 M to 1.0×10^?8 M , with a low detection limit of 2.0 fM towards the target sequences. The hybridization selectivity experiments further revealed that the complementary sequence, the one‐base‐mismatched sequence, and the non‐complementary sequence could be well‐distinguished by the cobalt‐complex‐based biosensor.     

Kinetic Determination of Uric Acid in Human Serum by Using the Uncatalyzed BZ Reaction in Non‐equilibrium Steady State

A novel kinetic method for determination of uric acid in human serum by means of an uncatalyzed BZ system consisting of potassium bromate and p‐hydroxybenzaldehyde (p‐HBA) in sulfuric acid medium was proposed, in which the analyte perturbation to the system was recorded close to the bifurcation point. The potential change was directly proportional to the logarithm of concentration of uric acid in the range of 3.73×10^?8–7.48×10^?4 mol·L^?1 (r=0.9983) with a detection limit of 7.45×10^?9 mol·L^?1 and a recovery from 98.9% to 101.1%. A comparison between the proposed technique and other methods indicated that results obtained were in agreement with those in clinical detection. In addition, the possible mechanism of action of uric acid on the uncatalyzed BZ reaction was also discussed briefly.     

Nanomolar Determination of Methyldopa in the Presence of Large Amounts of Hydrochlorothiazide Using a Carbon Paste Electrode Modified with Graphene Oxide Nanosheets and 3‐(4′‐Amino‐3′‐hydroxy‐biphenyl‐4‐yl)‐acrylic Acid

A novel electrochemical sensor for sensitive detection of methyldopa at physiological pH was developed by the bulk modification of carbon paste electrode (CPE) with graphene oxide nanosheets and 3‐(4′‐amino‐3′‐hydroxy‐biphenyl‐4‐yl)‐acrylic acid (3,′AA). Applying square wave voltammetry (SWV), in phosphate buffer solution (PBS) of pH 7.0, the oxidation current increased linearly with two concentration intervals of methyldopa, one is 1.0×10^?8–1.0×10^?6 M and the other is 1.0×10^?6–4.5×10^?5 M. The detection limit (3σ) obtained by SWV was 9.0 nM. The modified electrode was successfully applied for simultaneous determination of methyldopa and hydrochlorothiazide. Finally, the proposed method was applied to the determination of methyldopa and hydrochlorothiazide in some real samples.     

Electrochemical Determination of Boron in Natural Waters

Abstract

A sensitive voltammetric method for the determination of trace boron, based on the formation of the complex of boric acid with 4‐hydroxy‐5‐[salicylideneamino]‐2‐7‐naphthalenedisulfonic acid (azomethine H) is described. The reduction of the boric acid‐azomethine H complex at a hanging mercury drop electrode was exploited by square wave voltammetry (SWV) and cyclic voltammetry to determine boron in natural water samples, which were collected in the regions surrounding the boron mines of Central Anatolia. A reduction peak that belongs to the boric acid‐azomethine H complex at this electrode was observed at ?1.05 V vs. Ag/AgCl/KCl_(sat.). The effects of various parameters, such as ligand concentration, boric acid concentration, and formation time of the boric acid‐azomethine H complex, were investigated. Electrochemical experiments were conducted in 1.0 M HOAc/0.5 M NH₄OAc buffer at pH of 4.4±0.2. Linear working range was established by regression analysis between 5.0×10^?8 M and 1.0×10^?4 M. The probable metal cation interferences in water samples were eliminated by adding EDTA (ethylenediaminetetraacetic acid) to the samples. Data obtained using the square wave voltammetric (SWV) technique was compared statistically with inductively coupled plasma mass spectroscopy (ICP‐MS) data. Evaluation of the method based on statistical data was performed and the values of the limit of detection (LOD) and limit of quantitation (LOQ) were found to be 4.17×10^?6 M and 1.39×10^?5 M, respectively.     

Sensitive Determination of Clomipramine at Poly‐ABSA/Pt Nano‐Clusters Modified Glassy Carbon Electrode

Abstract

Clomipramine, an important tricylic antidepressant drug with low redox activity, was effectively electrocatalyzed on poly‐aminobenzene sulfonic acid/Pt nano‐clusters modified glassy carbon electrode (i.e., poly‐ABSA/Pt/GCE) and generated a sensitive anodic peak at about 0.80 V in pH 8.1 PBS. ABSA was electropolymerized on the surface of GCE modified with Pt nano‐clusters. Pt nanoparticles provide a 3 D and conductive structure for the polymer immobilization. The resulting sensor exhibited a considerable enhancement in voltammetric response characteristics: extending the linear range and lowering the detection limit. The anodic peak current of clomipramine was linear with its concentration over two concentration intervals, viz., 1.0×10^?7～4.0×10^?6 M and 4.0×10^?6～4.0×10^?5 M, with the detection limit of 1.0×10^?9 M (S/N=3). This method was successfully applied to the determination of clomipramine in drug tablets and proved to be reliable compared with UV.     

Electrocatalytic Oxidation and Voltammetric Determination of L‐Cysteic Acid at the Surface of p‐Bromanil Modified Carbon Paste Electrode

The electrochemical properties of L ‐cysteic acid studied at the surface of p‐bromanil (tetrabromo‐p‐benzoquinone) modified carbon paste electrode (BMCPE) in aqueous media by cyclic voltammetry (CV) and double step potential chronoamperometry. It has been found that under optimum condition (pH 7.00) in cyclic voltammetry, the oxidation of L ‐cysteic acid at the surface of BMCPE occurs at a half‐wave potential of p‐bromanil redox system (e.g., 100 mV vs. Ag|AgCl|KCl_sat), whereas, L ‐cysteic acid was electroinactive in the testing potential ranges at the surface of bare carbon paste electrode. The apparent diffusion coefficient of spiked p‐bromanil in paraffin oil was also determined by using the Cottrell equation. The electrocatalytic oxidation peak current of L ‐cysteic acid exhibits a linear dependency to its concentration in the ranges of 8.00×10^?6 M–6.00×10^?3 M and 5.2×10^?7 M–1.0×10^?5 M using CV and differential pulse voltammetry (DPV) methods, respectively. The detection limits (2σ) were determined as 5.00×10^?6 M and 4.00×10^?7 M by CV and DPV methods. This method was used as a new, selective, rapid, simple, precise and suitable voltammetric method for determination of L ‐cysteic acid in serum of patient's blood with migraine disease.     

Kinetic determination of some inorganic and organic compounds by oxidation with iodate

Sulphite (5.0 × 10^?1?5.0 × 10^?3 M), ascorbic acid and other compounds are oxidized by potassium iodate in dilute sulphuric acid; the production of iodide is monitored by an iodide-selective electrode. The time needed for a 40-mV potential change is inversely proportional to concentration. For sulphite (1.0 × 10^?5?1.0 × 10^?4 M), selectivity is improved by sweeping the sulphur dioxide formed in acidic EDTA-containing solution into the iodate solution.     

Sensitive Voltammetric Response of p‐Nitroaniline on Single‐Wall Carbon Nanotube‐Ionic Liquid Gel Modified Glassy Carbon Electrodes

An ionic liquid (i.e., 1‐butyl‐3‐methylimidazolium hexafluorophosphate, BMIMPF₆)‐single‐walled carbon nanotube (SWNT) gel modified glassy carbon electrode (BMIMPF₆‐SWNT/GCE) is fabricated. At it the voltammetric behavior and determination of p‐nitroaniline (PNA) is explored. PNA can exhibit a sensitive cathodic peak at ?0.70 V (vs. SCE) in pH 7.0 phosphate buffer solution on the electrode, resulting from the irreversible reduction of PNA. Under the optimized conditions, the peak current is linear to PNA concentration over the range of 1.0×10^?8–7.0×10^?6 M, and the detection limit is 8.0×10^?9 M. The electrode can be regenerated by successive potential scan in a blank solution for about 5 times and exhibits good reproducibility. Meanwhile, the feasibility to determine other nitroaromatic compounds (NACs) with the modified electrode is also tested. It is found that the NACs studied (i.e., p‐nitroaniline, p‐nitrophenol, o‐nitrophenol, m‐nitrophenol, p‐nitrobenzoic acid, and nitrobenzene) can all cause sensitive cathodic peaks under the conditions, but their peak potentials and peak currents are different to some extent. Their peak currents and concentrations show linear relationships in concentration ranges with about 3 orders of magnitude. The detection limits are 8.0×10^?9 M for p‐nitroaniline, 2.0×10^?9 M for p‐nitrophenol, 5.0×10^?9 M for o‐nitrophenol, 5.0×10^?9 M for m‐nitrophenol, 2.0×10^?8 M for p‐nitrobenzoic acid and 8.0×10^?9 M for nitrobenzene respectively. The BMIMPF₆‐SWNT/GCE is applied to the determination of NACs in lake water.     

Determination of Butylated Hydroxyanisole by Briggs‐Rauscher Oscillating Reaction Catalyzed by a Macrocyclic Nickel (II) Complex

A novel analytical approach for quantitative measurement of butylated hydroxyanisole (BHA) is dis‐ cussed in this paper. Such a method depends on the inhibitory effect of BHA on a Briggs‐Rauscher (B‐R) oscillating reaction. Unlike the classical B‐R system which involves Mn²⁺ as the catalyst, such a B‐R sys‐ tem is catalyzed by a macrocyclic nickel (II) complex [NiL](ClO₄)₂, where L in the complex is an unsatu‐ rated ligand 5,7,7,12,14,14‐hexemethyl‐1,4,8,11‐tetraazacyclotetradeca‐4,11‐diene. By perturbation of BHA on the system, the oscillation was inhibited in the presence trace amounts of BHA and the inhibition time was found to be proportional to the concentration of BHA over the range 1.00×10^?7–1.20×10^?4 mol/L. Two calibration curves were obtained: the first linear regression is over the range of 1.00×10^?7–2.00×10^?6 mol/L, and the second linear regression is over the range between 2.00×10^?6 and 1.20×10^?4 mol/L, with a lowest limit of detection of 4.00×10^?8 mol/L. UV spectra measurements were employed to clarify the possible perturbation mechanism caused by BHA on the B‐R oscillating reaction.     

Simultaneous spectrofluorimetric determination of terbium,samarium and europium with hexafluoroacetylacetone-trioctylphosphine oxide and Triton X-100

In aqueous solution, the fluorescence intensity is a linear function of concentration in the ranges 1.0 × 10^?4-1.0 × 1.0^?6 M Sm and 1.0 × 10^?6-1.0 × 10^?8 M Tb and Eu. The optimum conditions are 1 × 10^?3 M hexafluoroacetylacetone, 1 × 10^?4 M trioctylphosphine oxide and 0.05% Triton X-100 at pH 3.0.     

Catalytic Adsorptive Stripping Voltammetry of Germanium(IV) in the Presence of Gallic Acid and Vanadium(IV)‐EDTA

A highly sensitive and selective catalytic adsorptive cathodic striping procedure for the determination of trace germanium is presented. The method is based on adsorptive accumulation of the Ge(IV)‐gallic acid (GA) complex onto a hanging mercury drop electrode, followed by reduction of the adsorbed species. The reduction current is enhanced catalytically by addition of vanadium(IV)‐EDTA. The optimal experimental conditions include the use of 0.03 mol/L HClO₄ (pH1.6), 6.0×10^?3 mol/L GA, 3.0×10^?3 mol/L V(IV), 4.0×10^?3 mol/L EDTA, an accumulation potential of ?0.10 V(vs. Ag/AgCl), an accumulation time of 120 s and a differential pulse potential scan mode. The peak current is proportional to the concentration of Ge(IV) over the range of 3.0×10^?11 to 1.0×10^?8 mol/L and the detection limit is 2×10^?11 mol/L for a 120 s adsorption time. The relative standard deviation at 5.0×10^?10 mol/L level is 3.1%. No serious interferences were found. The method was applied to the determination of germanium in ore, mineral water and vegetable samples with satisfactory results.     

Voltammetric Determination of Uric Acid with a Glassy Carbon Electrode Coated by Paste of Multiwalled Carbon Nanotubes and Ionic Liquid

The voltammetric behavior of uric acid (UA) has been studied at a multiwalled carbon nanotube‐ionic liquid (i.e., 1‐butyl‐3‐methylimidazolium hexafluorophosphate, BMIMPF₆) paste coated glassy carbon electrode (MWNTs‐BMIMPF₆/GC). It is found that UA can effectively accumulate at this electrode and cause a sensitive anodic peak at about 0.49 V (vs. SCE) in pH 4.0 phosphate buffer solutions. Experimental parameters influencing the response of the electrode, such as solution pH and accumulation time, are optimized for uric acid determination. Under the optimum conditions, the anodic peak current is linear to UA concentration in the range of 1.0×10^?8 M to 1.0×10^?6 M and 2.0×10^?6 M to 2.0×10^?5 M. The detection limit is 5.0×10^?9 M for 180 s accumulation on open circuit. The electrode can be regenerated by successively cycling in a blank solution for about 3 min and exhibits good reproducibility. A 1.0×10^?6 M UA solution is measured for eight times using the same electrode regenerated after every determination, and the relative standard deviation (RSD) of the peak current is 3.2%. As for different electrodes fabricated by the same way the RSD (i.e., the electrode to electrode deviation) is 4.2%(n=9). This method has been applied to the determination of UA in human urine samples, and the recoveries are 99%–100.6%. In addition, comparison is made between MWNTs‐BMIMPF₆/GC and MWNTs/GC. Results show that the MWNTs‐BMIMPF₆/GC exhibits higher sensitivity, selectivity and ratio of peak current to background current.     

The Electrochemical Properties of Co(TPP), Tetraphenylborate Modified Glassy Carbon Electrode: Application to Dopamine and Uric Acid Analysis

We report the combination of the charge repelling property of tetraphenyl‐borate (TPB) anion and the electrooxidation catalytic effect of cobalt(II) tetrakisphenylporphyrin (CoTPP) embedded in a sol gel ceramic film to develop a modified glassy carbon electrode (CoTPP‐TPB‐SGGCE) for the simultaneous determination of dopamine (DA) and uric acid (UA). The optimized CoTPP‐TPB‐SGGCE shows excellent sensitivity and selectivity for the DA and UA analysis. As high as 2000 fold acceptable tolerance of ascorbic acid (AA) for the determination of trace DA and UA is reached. In the presence of 0.10 mM AA, the linear concentration range for DA is from 6.0×10^?8 to 2.5×10^?5 M, and the detection limit is 2.0×10^?8 M. For UA, the linear concentration range is from 1.0×10^?7 to 3.5×10^?5 M, and the detection limit is 7.0×10^?8 M. Our study has also demonstrated that the novel CoTPP‐TPB‐SGGCE shows high stability and reliability. For 6.00 μM DA and UA, a total of 12 measurements were taken in one week, and the relative standard deviation is 2.05% and 2.68% respectively. No obvious shift of peak current and peak potential is observed over a three‐month lifetime test. The response of the sensor is very quick and response time is approximately 1 s. Satisfactory results are also achieved when the CoTPP‐TPB‐SGGCEs being used to detect the DA and UA in human urine samples.     

Xanthine Sensors Based on Anodic and Cathodic Detection of Enzymatically Generated Hydrogen Peroxide

A xanthine biosensor was fabricated by the covalent immobilization of xanthine oxidase (XO) onto a functionalized conducting polymer (Poly‐5, 2′: 5′, 2″‐terthiophine‐3‐carboxylic acid), poly‐TTCA through the formation of amide bond between carboxylic acid groups of poly‐TTCA and amine groups of enzyme. The immobilization of XO onto the conducting polymer (XO/poly‐TTCA) was characterized using cyclic voltammetry, quartz crystal microbalance (QCM), and X‐ray photoelectron spectroscopy (XPS) techniques. The direct electron transfer of the immobilized XO at poly‐TTCA was found to be quasireversible and the electron transfer rate constant was determined to be 0.73 s^?1. The biosensor efficiently detected xanthine through oxidation at +0.35 V and reduction at ?0.25 V (versus Ag/AgCl) of enzymatically generated hydrogen peroxide. Various experimental parameters, such as pH, temperature, and applied potential were optimized. The linear dynamic ranges of anodic and cathodic detections of xanthine were between 5.0×10^?6?1.0×10^?4 M and 5.0×10^?7 to 1.0×10^?4 M, respectively. The detection limits were determined to be of 1.0×10^?6 M and 9.0×10^?8 M with anodic and cathodic processes, respectively. The applicability of the biosensor was tested by detecting xanthine in blood serum and urine real samples.     

Determination of Ascorbic Acid Using a New Oscillating chemical System of Lactic Acid—Acetone—BrO3^— —Mn^2 —H2SO4

ＩｎｔｒｏｄｕｃｔｉｏｎＯｓｃｉｌｌａｔｉｎｇｒｅａｃｔｉｏｎｓａｒｅｃｏｍｐｌｅｘｄｙｎａｍｉｃｓｙｓｔｅｍｓｔｈａｔｉｎｖｏｌｖｅｐｅｒｉｏｄｉｃｃｈａｎｇｅｓｉｎｔｈｅｃｏｎｃｅｎｔｒａｔｉｏｎｏｆｓｏｍｅｉｎｇｒｅｄｉｅｎｔｓ (ｗｈｅｔｈｅｒａｒｅａｃｔａｎｔ,ａｐｒｏｄｕｃｔｏｒａｎｉｎｔｅｒｍｅ ｄｉａｔｅ)ｗｉｔｈｔｉｍｅ .Ｔｈｅｓｉｍｉｌａｒｉｔｉｅｓｂｅｔｗｅｅｎｌｉｆｅｐｒｏｃｅｓｓｅｓｔｈａｔｅｘｈｉｂｉｔｏｓｃｉｌｌａｔｉｎｇｂｅｈａｖｉｏｒａｎｄｏｓｃｉｌｌａｔｉｎｇｃｈ…     

A New Chromium(III) Microelectrode Based on Self‐Assembled Diethylenetriamminepentaacetic Acid‐Poly(fuchsin basic) Modified Electrode

A new selective, sensitive, and rapid response microelectrode for microamount chromium(III) determination was developed. For the electrode preparation, fuchsin basic was electropolymerized onto a carbon microdisk electrode, and then diethylenetriamminepentaacetic acid (DTPA) was self‐assembled on the electrode surface by the reaction between DTPA and poly(fuchsin basic). The determination conditions were optimized. The electrode showed a linear response to Cr³⁺ ions in the concentration range of 1.0×10^?6?1.0×10^?4 M and exhibits a super‐Nernstian slope of 32.5±0.4 mV per decade. The detection limit is 3.6×10^?7 M. The response time of the electrode is less than 10 s, and it can be used for at least 2 months with limited considerable divergences in its potentials. The proposed electrode was applied for monitoring the chromium ion level in wastewater of chromate industries.     

Silicomolybdate‐Incorporated‐Glutaraldehyde‐Cross‐Linked Poly‐L‐Lysine Film Modified Glassy Carbon Electrode as Amperometric Sensor for Bromate Determination

Silicomolybdate‐doped‐glutaraldehyde‐cross‐linked poly‐L ‐lysine (PLL‐GA‐SiMo) film modified glassy carbon electrode was successfully prepared by means of electrostatically trapping the silicomolybdate anion in PLL‐GA cationic coating. The PLL‐GA‐SiMo film was stable and the charge transport through the film was fast. The modified electrode shows excellent electrocatalytic activity towards bromate reduction with significant reduction of overpotential. In amperometric determination of bromate, the calibration plot was linear over the concentration range of 5×10^?5 to 1.2×10^?3 M with a sensitivity of 3.6 μA mM^?1. Furthermore, PLL‐GA‐SiMo film electrode showed fast response and good stability.