Electrochemical properties of Li<Subscript>3</Subscript>V<Subscript>2</Subscript>(PO<Subscript>4</Subscript>)<Subscript>3</Subscript>/C cathode materials synthesized via ethylene glycol-assisted solvothermal method

The Li₃V₂(PO₄)₃/C (LVP/C) cathode materials for lithium-ion batteries were synthesized via ethylene glycol-assisted solvothermal method. The phase composition, phase transition temperature, morphology, and fined microstructure were studied using X-ray diffraction (XRD), differential thermal analyzer (DTA), scanning electron microscope (SEM), and transmission electron microscope (TEM), respectively. The electrochemical properties, impedance, and electrical conductivity of LVP/C cathode materials were tested by channel battery analyzer, the electrochemical workstation, and the Hall test system, respectively. The results shown that the appropriate amount of water added to ethylene glycol solvent contributes to the synthesis of pure phase LVP. The LVP₁₀/C cathode material can exhibit discharge capacities of 128, 126, 126, 123, 124, and 114 mAh g^?1 at 0.1, 0.5, 2, 5, 10, and 20 C in the voltage range of 3.0–4.3 V, respectively. Meanwhile, it shows also a stable cycling performance with the capacity retention of 89.6% after 180 cycles at 20 C.     

Electron microscopic study of chain aggregates of MoO<Subscript>3</Subscript> nanoparticles

Chain aggregates of MoO₃ nanoparticles have been obtained and their polymer-like properties revealed. Chain aggregates of MoO₃ nanoparticles, like polymers, form parallel packings, coils and exhibit coil-helix transition, Brownian motion, and high flexibility.     

Characterization of Y<Subscript>2</Subscript>BaCuO<Subscript>5</Subscript> nanoparticles synthesized by nano-emulsion method

Nanoscale yttrium–barium–copper oxide (Y₂BaCuO₅, Y211) particles were synthesized using the emulsion method and the solution method. The basic water-in-oil (w/o) emulsion system consisted of n-octane (continuous oil phase), cetyltrimethylammonium bromide (cationic surfactant), butanol (cosurfactant) and water. The composition of the emulsion system was varied and characterized by measuring the conductivity of the solutions and droplet size. The droplet size of emulsion was determined by using the dynamic light scattering method. The water content, cosurfactant content, and surfactant/n-octane ratio affected the droplet size which was in the range of 3–8 nm, and hence the w/o emulsion system was referred to as a nano-emulsion system. A model was used to verify the droplet size. The influence of salt (Y₂(NO₃)₃) content on the droplet size was investigated and the addition of salt reduced the droplet size. The effects of reaction time and temperature on the Y211 particle sizes were also investigated. The particles were characterized using the TEM, SEM, and XRD. Nanoparticles produced by the nano-emulsion method were calcined at 850°C to form the Y211 phase as compared to solid state processing temperature of 1050°C. Based on the TEM analysis, the average diameter of the Y211 particles produced using the nano-emulsion method was in the range of 30–100 nm. The effect of adding 15% Y211 nanoparticles to the superconductor YBCO-123 as flux pinning centers, was investigated, and the transition temperature was reduced by 3 K.     

Synthesis and gas sensing properties of perovskite CdSnO<Subscript>3</Subscript> nanoparticles

The CdSnO₃ semiconducting oxide that can be used as a gas-sensitive material for detecting ethanol gas is reported in this paper. CdSnO₃ nanoparticles were prepared by a chemical co-precipitation synthesis method, in which the preparation conditions were carefully controlled. The n-type gas-sensing semiconductors were obtained from the as-synthesized powders calcined at 600°C for 1 h. The phase and microstructure of the obtained nanoparticles were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), and Brunauer–Emmett–Teller (BET) method with a gas adsorption analyzer. CdSnO₃ has a small particle size range of 30–50 nm and a high surface area of 9.12 m²/g, and a uniformity global shape. The gas sensitivity and operating temperature, and selectivity of CdSnO₃-based sensors were measured in detail. The gas sensors fabricated by CdSnO₃ nanoparticles had good sensitivity and selectivity to vapor of C₂H₅OH when working temperature at 267°C, the value of gas sensitivity at 100 ppm of C₂H₅OH gas can reach 11.2 times. Furthermore, gas-sensing mechanism was studied by using chromatographic analysis.     

Photoaccumulating film systems based on TiO<Subscript>2</Subscript>/MoO<Subscript>3</Subscript> and TiO<Subscript>2</Subscript>/MoO<Subscript>3</Subscript>:V<Subscript>2</Subscript>O<Subscript>5</Subscript> nanoheterostructures

The thin-film photocatalysts TiO₂/MoO₃ and TiO₂/MoO₃:V₂O₅ obtained by a combination of sol–gel and sintering techniques were studied using the photooxidation of probing dyes, EPR spectroscopy, X-ray diffraction analysis, and electron microscopy. It was shown that due to charge accumulation caused by UV irradiation, these photocatalysts retain their oxidative activity and ability for self-sterilization in the dark for a long time after irradiation was terminated (up to 5 h for TiO₂/MoO₃:V₂O₅).     

Magnetic and dielectric properties of Mn<Subscript>0.2</Subscript>Ni<Subscript>0.8</Subscript>Fe<Subscript>2</Subscript>O<Subscript>4</Subscript> nanoparticles synthesized by PEG-assisted hydrothermal method

We present a systematic investigation on the structural and magnetic properties of Mn_0.2Ni_0.8Fe₂O₄ nanoparticles synthesized by a polyethylene glycol (PEG)-assisted hydrothermal route. XRD, FT-IR, TEM and VSM were used for the structural, morphological, dielectric properties and magnetic investigation of the products, respectively. Average crystallite size of product was estimated using Line profile fitting as 6 ± 1 nm and particle size as 6.5 ± 1.0 nm from TEM micrographs. Magnetization measurements have shown that the particles have a blocking temperature of 134 K. Magnetization and the coercive field of the sample increase by decreasing the temperature. The conductivity measurements reveal the semiconducting behaviour for the sample. Temperature-dependent dielectric properties: dielectric permittivity (ε) and ac conductivity (σ_ac) for the sample were studied as a function of applied frequency in the range from 1 Hz to 3 MHz. These studies indicated that the dielectric dispersion curve for the sample showed usual dielectric dispersion which can be explained on the basis of Koop’s theory, which is based on the Maxwell–Wagner model for the interfacial polarization of homogeneous double structure.     

Photoinduced processes in thin films of MoO<Subscript>3</Subscript> and mixed V<Subscript>2</Subscript>O<Subscript>5</Subscript>: MoO<Subscript>3</Subscript> oxides

Photoinduced processes in thin films of MoO₃ and mixed V₂O₅: MoO₃ oxides prepared by polycondensation of the respective oxoacids under solvothermal conditions are studied using Raman spectroscopy, ESR, and AFM. It is shown that, under UV irradiation, the photoinduced polycondensation occurs in the oxide films, leading to the formation of the oxygen bridges, an effect that opens up the possibility of developing a new photolithographic process.     

Spectral properties of a Nd<Superscript>3+</Superscript>-doped Li<Subscript>3</Subscript>Ba<Subscript>2</Subscript>Gd<Subscript>3</Subscript>(MoO<Subscript>4</Subscript>)<Subscript>8</Subscript> crystal

The spectral properties of a promising laser material, ternary molybdate Li₃Ba₂Gd₃(MoO₄)₈:Nd³⁺, are studied (i.e., its optical absorption spectra, luminescence spectra, kinetic of luminescence decay, and temperature dependence of luminescence). Luminescence of the crystalline matrix is detected, and the temperature dependence of its intensity and reabsorption by neodymium are investigated.     

NO<Subscript>2</Subscript>-sensing properties of La<Subscript>0.65</Subscript>Sr<Subscript>0.35</Subscript>MnO<Subscript>3</Subscript> synthesized by self-propagating combustion

Ultrafine-structure La_0.65Sr_0.35MnO₃ (LSM) powders synthesized by self-propagating combustion method have been used to fabricate sensing electrodes (SEs) for NO₂ mixed-potential sensors based on yttria-stabilized zirconia (YSZ). This type of sensor was found to provide better NO₂ sensitivity at 500 °C than sensors with LSM powders synthesized by traditional solid-state methods. The response values of the sensor have good linear relationship (sensitivity 36.6 mV/decade and linear fit 0.99) with the logarithm of NO₂ concentration varying from 30 to 500 ppm. The influence of sintering temperature (1000, 1100, 1200, and 1300 °C) on sensor response was also examined and was found to have a significant effect on the morphology of LSM-SEs. Moreover, in the presence of NO, CO₂, CO, and NO₂, the sensor exhibited good NO₂ selectivity.     

Growth and magneto-optical properties of LiTb(MoO<Subscript>4</Subscript>)<Subscript>2</Subscript> crystal

Lithium terbium molybdate (LiTb(MoO₄)₂) single crystal was grown by the Czochralski method. The lattice parameters of the crystal were determined by X-ray diffraction analysis. The absorption coefficient and the Faraday rotation spectrum (B=1.07 T) were investigated at wavelengths of 400–1500 nm at room temperature. Verdet constants of LiTb(MoO₄)₂ crystal at 532-, 633- and 1064-nm wavelengths were measured by the extinction method. The results show that LiTb(MoO₄)₂ crystal has a larger magneto-optical figure of merit than that of terbium gallium garnet at wavelengths of 600–1500 nm.     

Structural transformation of MoO<Subscript>3</Subscript> nanobelts into MoS<Subscript>2</Subscript> nanotubes

The structural transformation of MoO₃ nanobelts into MoS₂ nanotubes using a simple sulfur source has been reported. This transformation has been extensively investigated using electron microscopic and spectroscopic techniques including scanning electron microscopy (SEM), transmission electron microscopy (TEM), high-resolution transmission electron microscopy (HRTEM), electron diffraction (ED), and energy-dispersive X-ray analysis (SEM-EDAX and TEM-EDX). The method described in this report will serve as a generic route for the transformation of other oxide nanostructures into the chalcogenide nanostructures.     

Regular hexagonal MoS<Subscript>2</Subscript> microflakes grown from MoO<Subscript>3</Subscript> precursor

Regular hexagonal MoS₂ microflakes with high yield were grown from MoO₃ precursor by a sulfurization process using S powders as sulfuration reducer. The precursors, long and smooth MoO₃ microbelts, were synthesized through a direct oxidation reaction of Mo plates in air. X-ray powder diffraction and scanning electron microscopy revealed that the sulfurized products were hexagonal MoS₂ with regular hexagonal flake-like morphology. The results of transmission electron microscopy examinations demonstrated that the microflakes were single crystalline MoS₂. Elemental analysis by EDAX and XPS showed that the microflakes consist of Mo and S with the atomic ratio near to 0.5. Factors influencing the formation of the product were systematically studied. PACS 81.15.Gh; 81.15.Kk; 81.05.Hd; 78.67.Pt; 82.40.Ck     

Nanosized rare earth cobaltite LaCoO<Subscript>3</Subscript> synthesized by urea combustion method

The structural, magnetic, and electrical properties of nano- and bulk samples of LaCoO₃, prepared by a urea combustion method, are investigated in this paper. The structures of phases, calcined at different temperatures, were refined in two different space groups rhombohedral R-3c and monoclinic I2/a, and a good agreement was obtained between the observed and calculated XRD patterns. Magnetic measurements reveal that the magnetic susceptibility increases with reduction in particle size. It is observed that there are two types of mechanisms which govern the conduction in different temperature ranges of these samples, and no single law of conduction fits the entire range of temperature. In high temperature range (200–300 K), Arrhenius law fits well, while in the low temperature region (100–200 K), the conduction is governed by Efros-Shklovskii’s (ES) hopping.     

Spectroscopy of NaLa(MoO<Subscript>4</Subscript>)<Subscript>2</Subscript>: Tm<Superscript>3+</Superscript> and NaGd(MoO<Subscript>4</Subscript>)<Subscript>2</Subscript>: Tm<Superscript>3+</Superscript> crystals as advanced laser materials

Single crystals of double sodium-containing lanthanum and gadolinium molybdates doped with Tm³⁺ ions were synthesized by the Czochralski method. The spectroscopic properties of these crystals were investigated from the viewpoint of their use as active media in diode-pumped lasers. The polarized spectra of absorption on the ³ H ₄ and ³ F ₄ levels and the polarized spectra of luminescence due to the ³ F ₄-³ H ₆ laser transition were recorded, and the lifetimes of the ³ H ₄ and ³ F ₄ excited states of the Tm³⁺ ions were determined. The luminescence cross sections were calculated using the Füchtbauer-Ladenburg formula. The simulation of the decay curve of the ³ H ₄ excited state according to the Golubov-Konobeev-Sakun method revealed that, in the crystals under investigation, the interaction between Tm³⁺ ions predominantly occurs through the dipole-dipole mechanism.     

Optical properties of pyridine funtionalized TbF<Subscript>3</Subscript> nanoparticles

The preparation of pyridine functionalized TbF₃ nanoparticles are described in this report. Synthesized nanoparticles were characterized using the TEM, UV/Vis, FTIR and photoluminescence spectroscopy. TEM micrograph reveals the nanorod shaped, uniform in size with a particles size in the range of 20–30 nm. FTIR spectrum shown characteristic absorption bands of pyridine and a small intensity band at 411 cm⁻¹ corresponding metal nitrogen ν(Tb–N) bonding. Uv-vis spectrum shown the characteristic absorption transitions of Tb³⁺ ion. A strong emission transition at 540 nm (⁵D₄ → ⁷F₅) was observed on excite by visible light at 414 nm.     

Cooperative down-conversion of UV light in disordered scheelitelike Yb-doped NaGd(MoO<Subscript>4</Subscript>)<Subscript>2</Subscript> and NaLa(MoO<Subscript>4</Subscript>)<Subscript>2</Subscript> crystals

Concentration series of disordered scheelitelike Yb:NaGd(MoO₄)₂ and Yb:NaLa(MoO₄)₂ single crystals are grown by the Czochralski method. The actual concentrations of Yb³⁺ ions in the crystals are determined by optical-absorption spectroscopy. The luminescence of Yb³⁺ ions in these crystals in the region of 1 μm is studied under UV and IR excitation. In the case of UV excitation, this luminescence appears as a result of nonradiative excited state energy transfer from donor centers of unknown nature to ytterbium. The character of the concentration dependence of Yb³⁺ luminescence indicates that the energy transfer at high Yb concentrations occurs with active participation of a cooperative mechanism, according to which the excitation energy of one donor center is transferred simultaneously to two Yb³⁺ ions. In other words, the quantum yield of this transfer exceeds unity, which can be used to increase the efficiency of crystalline silicon (c-Si) solar cells.     

Structural aspects of solid-state amorphization in Eu<Subscript>2</Subscript>(MoO<Subscript>4</Subscript>)<Subscript>3</Subscript> single crystals

X-ray diffraction studies of Eu₂(MoO₄)₃ single crystals were performed, which demonstrate that, in contrast to polycrystalline samples, these crystals do not exhibit amorphous-like diffraction patterns during the reverse transition from the high-pressure phase into the initial β phase; rather, the diffracted intensity in their diffraction patterns decreases significantly to the background. Such a diffraction pattern can be explained under the assumption that a single crystal is divided into small (nanoscopic) regions inside which the lattice parameters of the high-pressure phase and the initial β phase change continuously. The simultaneous recovery of the single-crystal state of the β phase from this intermediate state in all nanoscopic regions as the annealing temperature increases indicates that nanocrystals in this state are structurally correlated with each other. This result suggests that the halo-type diffraction patterns of polycrystalline samples reflect an intermediate state between the high-pressure phase and the β phase in every initial crystallite (as in the single crystals) rather than being caused by an amorphous structure of the sample. In this case, the total diffraction pattern of differently oriented crystallites gives an amorphous-like diffraction pattern reflecting the contributions from numerous various crystallographic planes involved in diffraction.     

Characterization of MoO<Subscript>3</Subscript> nanobelt cathode for Li-battery applications

Molybdenum trioxide (MoO₃) and PPy_xMoO₃ (x=0.5 and 1) nanobelts were obtained by the simple hydrothermal process from MoO₃ sol. The morphology and structure of the samples were characterized using X-ray diffractometry (XRD), Fourier transformation infrared spectroscopy (FTIR), Raman spectra, SEM and AFM. The results show that the H atoms in polypyrrole are H-bonded with the O atoms in the Mo=O bonds of MoO₃ nanobelts. Using the electrolyte, we fabricated electrochemical cells with a configuration of Li/(LiPF₆+EC+DMC)/(MoO₃+acetyleneblack+PTFE) and studied discharge profiles. PACS 81.07.BC; 81.05.Je; 82.47.Aa; 82.45.Fk; 82.45.Gj